200-301 · domain
IP Routing
IP Routing covers how a Cisco router builds its routing table, chooses a path, and forwards packets between subnets. You must read show ip route output, compare static, OSPF, and default routes, and explain longest-prefix match and administrative distance decisions on Cisco IOS routers.
Focused practice
Practice IP Routing questions
Scored sessions drawing only from this domain — pick a length below.
Start 20-question practice test →What this domain covers
What to know about IP Routing
Be able to read a routing table and decide which route installs and forwards a given destination. The single most important thing: longest-prefix match first, then administrative distance, then metric.
Interpreting show ip route codes, next-hop addresses, and outgoing interfaces
Longest-prefix match selection among connected, static, and OSPF routes
Administrative distance comparison, including static routes with modified distance
Static route configuration with ip route, including default and floating routes
Watch out for
Common IP Routing exam traps
- ▸Assuming the lowest administrative distance always wins; longest prefix match is checked before administrative distance.
- ▸Forgetting that a static route with distance 200 loses to OSPF (distance 110) while OSPF is up.
- ▸Mixing up next-hop IP and exit interface in static routes, causing unresolved or recursive routing.
Question index
All IP Routing questions (279)
Click any question to see the full explanation, or start a practice session above.
Drag and drop the following steps into the correct order to configure an IPv4 default static route with a floating static backup route on a Cisco router and save the configuration. Select the correct sequence.
Medium2You are connected to R1 via console. R1 and R2 are directly connected through their GigabitEthernet0/0 interfaces (R1 2001:db8:acad:1::1/64, R2 2001:db8:acad:1::2/64). R2 already runs OSPFv3 in area 0 on G0/0 and on Loopback0 (2001:db8:acad:2::1/64). R1 has no IPv4 addresses. Configure OSPFv3 on R1 so that R2's loopback network is reachable from R1, then verify the neighbor and route. Select the correct approach.
Hard3Which TWO statements correctly describe the behavior of the passive-interface command in single-area OSPFv2?
Medium4A router has learned route 172.16.50.0/24 from OSPF with cost 20 and also has a static route to the same prefix with administrative distance 5. Which two statements are correct about route selection?
Hard5A technician configures OSPF on R1 using the command network 10.0.0.0 0.0.0.255 area 0. R1's GigabitEthernet0/0 interface has IP address 10.0.0.1/30 and is included in the OSPF process. The technician confirms the interface is not passive using the show ip ospf interface GigabitEthernet0/0 command. However, R2 is not forming an OSPF adjacency with R1. What should the technician do next?
Hard6A router has learned a route to 10.10.10.0/24 from both OSPF and EIGRP. The OSPF route has a metric of 20, and the EIGRP route has a metric of 1000. Which route will be installed in the routing table, and why?
Medium7A route to 192.168.1.0/24 appears in the routing table from OSPF, but a more specific static route to 192.168.1.128/25 is also configured. Which route is used for traffic to 192.168.1.200?
Hard8An engineer is troubleshooting an OSPF adjacency issue between two Cisco routers, R1 and R2, connected via GigabitEthernet0/0 on both sides. Hosts on R1's LAN cannot ping hosts on R2's LAN. The engineer checks the OSPF neighbor state on R1 and sees the adjacency is stuck in EXSTART/EXCHANGE. The router IDs are 1.1.1.1 on R1 and 2.2.2.2 on R2, and both routers have a network statement for their directly connected subnet. What is the most likely cause of this problem?
Hard9A router learns route 198.51.100.0/24 from OSPF with AD 110 and also has a static route to the same prefix configured with AD 150. Which route is installed?
Hard10A network engineer configures OSPF on R1 and R2 over a point-to-point link. The interfaces are in the same OSPF area, with matching hello and dead timers, and are on the same IP subnet. However, the command show ip ospf neighbor on both routers shows no neighbors. A firewall sits between R1 and R2. What should the technician do next?
Hard11Based on the exhibit, which route will be used for destination 192.168.10.130?
Hard12A network technician is examining the routing table of a Cisco router and sees the following entry: O 10.10.10.0/24 [110/2] via 192.168.1.2, 00:00:23, GigabitEthernet0/1. What does the value 110 represent in this output?
Easy13R1 is not forming an OSPF adjacency with R2 on GigabitEthernet0/1. Which mismatch below is the most likely cause?
Hard14A router has a static route for 172.16.10.128/25 and an OSPF-learned route for 172.16.10.0/24. When forwarding traffic to 172.16.10.130, why does the router use the static route instead of the OSPF route?
Hard15A router receives a destination prefix from EIGRP with administrative distance 90 and also from OSPF with administrative distance 110. The prefix length is identical. Which route source is preferred?
Hard16A router learns the same destination prefix from OSPF and from a static route configured with administrative distance 90. Which route is preferred by default?
Hard17An engineer is troubleshooting an OSPFv3 adjacency issue between two routers R1 and R2 connected over a serial link. The link is up/up on both sides, and IPv6 is enabled on the interfaces. However, the 'show ipv6 ospf neighbor' command shows no neighbors. The engineer checks the OSPFv3 configuration. What is the most likely cause of the missing adjacency?
Hard18Match each routing concept to its most accurate meaning.
Medium19Drag and drop the following steps into the correct order to configure IPv4 and IPv6 static routes (including a default route and a floating static route with a higher administrative distance) on a router and then verify the routing tables. Select the correct sequence.
Medium20A network engineer wants a static route to be used only when the OSPF-learned route disappears. Which configuration approach meets that goal?
Medium21A network administrator is configuring a router to forward all unknown IPv4 traffic to the next-hop address 192.168.1.1. Which command correctly creates this default static route?
Easy22What is the main purpose of this configuration? ipv6 route 2001:db8:100::/64 GigabitEthernet0/0
Hard23A network administrator has configured HSRP between RouterA and RouterB for VLAN 10. End hosts using the virtual IP 192.168.1.1 as their default gateway experience intermittent connectivity losses, and pings to 192.168.1.1 often fail. The output of 'show standby brief' on both routers shows the state as Active. What is the most likely cause?
Hard24R1 and R2 are directly connected. Their interfaces are up/up and belong to the same subnet. R1's OSPF configuration places the interface in area 0, while R2's interface is in area 1. R1 does not show R2 as an OSPF neighbor. What is the most likely cause?
Hard25A router is running OSPFv2 and has learned multiple routes to the same destination. You need to ensure that OSPF installs the route with the lowest cost into the routing table. Which two statements about OSPF path selection are true? (Choose two.)
Hard26Which TWO statements about HSRP active/standby election, priority, and preempt are true?
Medium27R1 is an IPv6-only branch router. The administrator wants all unknown IPv6 destinations to be sent to the upstream router at 2001:db8:ff::1. Which command best achieves that goal?
Hard28You are connected to R1 via console. R1 must forward traffic to the 203.0.113.0/24 and 2001:db8:1::/48 networks through R2 (10.0.0.2/30, 2001:db8:ff::2/64). The primary path must use a next-hop of 10.0.0.2 for IPv4 and 2001:db8:ff::2 for IPv6. Additionally, configure a floating static default route for IPv4 that uses R3 (192.0.2.2/30) as a backup only when the primary path fails. The current configuration has errors: the IPv4 static route points to a wrong next-hop (10.0.0.5) and the primary default route is missing, causing the floating route (AD 100) to become active instead of serving as a backup. Fix these issues so that both primary and backup routes work correctly.
Hard29You are connected to R1. R1 and R2 are HSRP peers for VLAN 100 (group 1, virtual IP 192.0.2.254). R2 uses the default priority 100. R1 must be the active gateway, preempt, and track its G0/1 interface with a decrement of 20. The exhibit shows R1's current state. Which change on R1 makes R1 the active router?
Hard30Why does traffic to 172.31.80.10 use the RIP route (172.31.80.0/24) instead of the static route (172.31.0.0/16)?
Hard31Which two statements accurately describe longest-prefix match in routing?
Medium32You are connected to R1. Configure R1 so that it uses a floating static route to reach the 203.0.113.0/24 network via R2 only when the primary route (learned via EIGRP) fails. The primary route has an administrative distance of 90. Currently, R1 has no route to 203.0.113.0/24 because EIGRP is down on the direct link. Ensure the floating static route is installed and used.
Hard33A static route is configured as 198.51.100.0/24 via 192.0.2.9, but the connected network to the next hop goes down. What happens to the static route in the routing table?
Hard34Drag and drop the following OSPFv2 neighbor state transitions and DR/BDR election steps into the correct order for a multi-access network with default priority values.
Medium35When two routes to the same destination are learned by OSPF from different paths, what criterion does OSPF use to select the best path?
Medium36You are connected to R1 via console. Configure OSPFv3 for IPv6 on both R1 and R2 so that the loopback0 interface on R2 (IPv6 address 2001:db8:1:2::1/64) is reachable from R1. The link between R1 and R2 uses the subnet 2001:db8:1:1::/64 with R1's G0/0 having IPv6 address 2001:db8:1:1::1/64 and R2's G0/0 having 2001:db8:1:1::2/64. OSPFv3 process ID must be 100 and every interface that runs OSPFv3 must be in area 0. After configuration, verify OSPFv3 neighbors and the IPv6 route to the loopback0 network.
Hard37A router output shows this neighbor state: Neighbor ID 10.1.1.1 State FULL/DR Address 192.168.12.1 What does the FULL/DR state indicate?
Medium38A technician is troubleshooting an OSPF adjacency problem: R1 and R2 are not forming a neighbor relationship. R1's OSPF configuration includes the command 'network 192.168.1.0 0.0.0.255 area 0'. R2's GigabitEthernet0/0 is configured with IP address 10.1.1.1/30 and is participating in OSPF area 0. The engineer verifies that physical connectivity is fine and OSPF is enabled on R2. What is the most likely cause?
Hard39R1 and R2 are directly connected. Both are configured in OSPF area 0, and they can successfully ping each other. However, OSPF neighbor adjacency fails. R1's interface is configured with `ip ospf authentication message-digest` and a valid key, while R2's interface has no OSPF authentication configured. What is the most likely cause?
Hard40A router has both an OSPF route and a static route to the same destination. The static route has an administrative distance of 200. What is the expected behavior while the OSPF route remains available?
Hard41An administrator configured a floating static default route on R1 as a backup to reach 10.10.10.0/24. The primary path is learned via OSPF, and the floating static route uses an administrative distance of 130. After the primary OSPF neighbor fails, traffic to 10.10.10.0/24 is dropped. According to the exhibit, why is the backup default route not being used?
Hard42Exhibit: R1 shows an OSPF neighbor stuck in EXSTART with R2 on a serial link. What is the most likely cause?
Medium43You are connected to R1. The network uses HSRP group 1 for default gateway redundancy on 192.168.1.0/24 with virtual IP 192.168.1.254. R2 is already configured with priority 100 and preempt, and R2 should be the active router with R1 as standby. Currently R1 (priority 110) is active. On R1, set the priority to 90, keep preempt enabled, and track interface GigabitEthernet0/1 (line protocol) so that the priority drops by 20 if that interface goes down. Verify with show standby brief.
Hard44Which WAN technology is most closely associated with establishing a direct point-to-point data-link connection between two routers over a serial link?
Medium45A packet destined for 10.1.1.130 arrives at the router. Based on the routing table, which route will be used?
Hard46You are connected to R1. R1 must reach the loopback network 203.0.113.0/24 on R3 through two paths: a primary static route via R2's G0/0 (192.0.2.2) and a floating backup static route via R2's G0/1 (198.51.100.2). R1 already has a default route via 192.0.2.2. Currently both static routes to 203.0.113.0/24 are installed and traffic is load-balanced across both paths. Fix the configuration so that the backup route is used only if the primary fails.
Hard47You are troubleshooting connectivity from R1 to the 203.0.113.0/24 network. R1 has a primary static route via R2 (192.0.2.2) and a floating backup static route via R3 (198.51.100.2). The link to R2 is up, but R1 is sending traffic via R3. Examine the routing table and configuration, and fix the primary route so that R2 is used while the link is up and the R3 route takes over only when the primary route is lost.
Hard48A router learns 10.10.10.0/24 from OSPF and EIGRP at the same time. OSPF reports a metric of 20, and EIGRP reports a metric of 30720. Which route is installed in the routing table by default?
Medium49A router has a static default route with administrative distance 250 and also learns a default route through OSPF. What is the main design purpose of the static default route?
Hard50A router learns 10.0.0.0/8 from OSPF and 10.10.0.0/16 from a static route. Which route is used for traffic to 10.10.20.1?
Hard51A network administrator is configuring a Cisco router to use OSPFv2 for IPv4 routing. The router is connected to two OSPF areas: area 0 and area 1. The administrator wants to ensure that the router becomes an Area Border Router (ABR) and that it can exchange routes between the areas. Which two statements are true about the OSPFv2 configuration and operation in this scenario? (Choose two.)
Hard52Drag and drop the following steps into the correct order to determine the best route to a destination using a routing table.
Medium53What is the operational purpose of configuring the IPv6 route ::/0?
Medium54A router has routes to 10.50.0.0/16, 10.50.10.0/24, and 10.50.10.128/25. Which route is used for traffic to 10.50.10.140?
Hard55Refer to the exhibit. A network administrator is troubleshooting a connectivity issue between two remote sites connected via a WAN link. Hosts on VLAN 10 at Site A (192.168.10.0/24) cannot ping the server at Site B (10.10.20.100). The configuration on RouterA contains 'ip route 0.0.0.0 0.0.0.0 10.10.10.2', but the default route does not appear in the routing table. What is the most likely cause of the problem?
Hard56You are connected to R1 via console. R1 has two Internet connections: ISP1 with next hop 203.0.113.1 (the primary) and ISP2 with next hop 203.0.113.5 (the backup). R1 currently has a static default route to ISP1 only. Configure a floating static default route to ISP2 with an administrative distance of 150 so that it is used only when the route to ISP1 is not available.
Medium57A network administrator is troubleshooting a connectivity issue on a subnet where two routers, R1 and R2, are configured with HSRP to provide a virtual gateway. Hosts on the subnet can ping the virtual IP address but cannot reach destinations outside the subnet. The administrator discovers that R1 is the active HSRP router. What is the most likely root cause of the problem?
Hard58A network engineer is configuring HSRP group 1 on two Cisco routers. R1 is configured with 'standby 1 priority 110' and R2 uses the default priority. The goal is for R1 to be the active router and to automatically reclaim the active role after it recovers from a failure. Which additional configuration is required on R1?
Medium59Exhibit: R1 learns 192.168.50.0/24 from multiple sources. Which two statements are correct about the route that will be installed in the routing table?
Medium60Which three options accurately describe characteristics of OSPFv2 in a single area? (Choose three.)
Medium61Exhibit: A router has both an OSPF-learned default route and a floating static default route. Which route is currently active?
Hard62A junior network engineer configured a floating static route on Router R1 as backup connectivity to the remote network 10.10.10.0/24. The primary path uses OSPF. After the primary link fails and the OSPF route is withdrawn, hosts behind R1 still cannot reach 10.10.10.0/24, and the floating static route is not in the routing table. Based on the exhibit, what is the most likely cause?
Hard63You are connected to R1. Configure OSPFv3 for IPv6 on R1 and R2 so that the loopback0 interface on R1 (IPv6 address 2001:db8:1::1/64) can ping the loopback0 interface on R2 (IPv6 address 2001:db8:2::1/64). The routers are connected via their GigabitEthernet0/0 interfaces using IPv6 addresses 2001:db8:12::1/64 (R1) and 2001:db8:12::2/64 (R2). OSPFv3 process ID 100 must be used, and all interfaces must be in area 0.
Hard64Two routers are directly connected and running OSPF. Their IP addresses and hello timers match, but they still do not become neighbors. One side is configured for area 0 and the other for area 1 on the shared link. What is the most likely cause?
Hard65Drag and drop the following steps into the correct order to describe how a router forwards an IPv4 packet, from the destination address to the outgoing frame.
Hard66Which two statements about OSPF neighbor requirements on a shared Ethernet segment are correct? (Choose two.)
Medium67A router shows this output: R1#show ip ospf neighbor Neighbor ID Pri State Dead Time Address Interface 10.1.1.2 1 FULL/DR 00:00:34 192.168.12.2 GigabitEthernet0/0 10.1.1.3 1 2WAY/DROTHER 00:00:39 192.168.12.3 GigabitEthernet0/0 Which statement is correct?
Hard68Drag and drop the following steps into the correct order to configure OSPFv2 process 1 on R1 so that adjacencies form only on GigabitEthernet0/1 (in 10.1.1.0/24) and hellos are suppressed on all other OSPF interfaces: process and router ID, network statement, passive default, then the exception.
Medium69Which TWO statements about IPv4 and IPv6 static routing are correct?
Medium70A route to 10.10.10.0/24 is learned through two OSPF paths. Both have the same prefix length and the same administrative distance, but one path has a lower OSPF metric. Which path is preferred?
Hard71A router learns the same destination prefix from OSPF and EIGRP. The prefix length is identical, and both routes are valid. Which route is preferred by default?
Hard72Which two statements accurately describe OSPF passive interfaces?
Medium73Which command correctly configures an IPv6 default route using next-hop address 2001:db8:1::1?
Medium74A network engineer is configuring a floating static route on a Cisco router to provide backup connectivity to a remote network 172.16.0.0/16. The primary route is learned via OSPF. The engineer wants the static route to be used only if the OSPF route is lost. Which command should be used?
Hard75Why does a passive interface in OSPF still matter even though it does not send hello packets?
Medium76You are troubleshooting backup connectivity from R1 to 172.16.20.0/24. A floating static route was configured as a backup for the OSPF-learned route via R2, but when the OSPF neighbor R2 fails, R1 still cannot reach 172.16.20.0/24 through R3. Examine the output and fix the static route so that it takes over when the OSPF route disappears.
Hard77You are connected to R1 via console. R1 and R2 are connected via a serial link. OSPFv2 has been configured, but the adjacency is stuck in EXSTART state. You suspect a mismatched MTU. On R1, the interface MTU is currently set to 1400, while R2 uses the default MTU of 1500. You need to verify and fix the issue.
Hard78A network administrator is configuring OSPFv2 on a Cisco router. The router is connected to two different areas: Area 0 and Area 1. The administrator wants to summarize the routes from Area 1 into Area 0. Which two statements are true about OSPF inter-area route summarization? (Choose two.)
Medium79You are connected to R1 via the console. R1 and R2 are running OSPFv2 in area 0. R1's router ID is 1.1.1.1, and R2's router ID is 2.2.2.2. Both routers are connected via GigabitEthernet0/0 on the 192.168.12.0/30 subnet. You need to ensure that R1 does not send OSPF hello messages out of its Loopback0 interface, while still advertising the loopback network into OSPF.
Medium80A routing table entry begins with the code C. What does that code indicate?
Medium81Two routers are directly connected over IPv6 and should form an OSPFv3 adjacency, but they do not. Link-local addressing is present on both interfaces. Which issue is most likely to prevent the adjacency?
Hard82What problem is HSRP designed to solve?
Medium83Two OSPF routers connected on an Ethernet link remain in the INIT state. Which issue is the most likely cause?
Hard84Drag and drop the OSPF neighbor states into the order a neighbor passes through on a broadcast link, from Down to Full.
Medium85Drag and drop the following commands into the correct order to configure OSPFv3 for IPv6 on a Cisco router.
Medium86R1 and R2 are directly connected and running OSPF. The IP addressing is correct and both routers are in area 0, but they do not form an adjacency. What is the most likely cause?
Hard87Why is route summarization often useful at distribution or area boundaries in larger networks?
Medium88A router learns 192.168.30.0/24 from OSPF and also has a static route to 192.168.30.0/24 with administrative distance 200. Which route is installed in the routing table while both are available?
Hard89A router receives two routes to 10.50.0.0/16: one from OSPF and one static route with an administrative distance of 90. Which route is installed by default?
Hard90A router has routes to 192.168.0.0/16 and 192.168.100.0/24. Which route is used for traffic to 192.168.100.77?
Hard91A routing table contains these entries for the same destination space: 10.1.0.0/16, 10.1.10.0/24, and 0.0.0.0/0. Which route is used for traffic to 10.1.10.44?
Hard92R1 must use R2 (10.0.0.2 / 2001:DB8:1:1::2) as the primary default route and R3 (10.0.0.6 / 2001:DB8:2:1::2) as a backup that is used only if the primary fails. The current IPv4 configuration installs both default routes at the same time and no IPv6 default route exists. Fix IPv4 and add IPv6 floating static default routes (backup AD 10).
Hard93An engineer is troubleshooting an OSPF adjacency between two directly connected routers, R1 and R2. R1 is configured with a passive-interface default under the OSPF process, and the interface connecting to R2 is not explicitly set to no passive-interface. The engineer runs a show ip ospf neighbor command on R1 and sees no neighbors. What is the most likely reason for the missing adjacency?
Hard94An OSPF router learns a route with metric 20 and another OSPF route to the same destination with metric 30. The prefix length is the same. Which path is preferred?
Hard95Which TWO statements correctly describe the configuration and verification of OSPFv3 for IPv6?
Medium96Two directly connected routers do not become OSPF neighbors. IP addressing, subnet masks and area assignment are correct. Based on the exhibit, what is the most likely cause?
Hard97R1 must reach the loopback 2001:db8:1::1/128 on R3 through R2 (2001:db8:0:2::2/64 on the R1-R2 link), but IPv6 pings fail. Also, the IPv4 default route via R2 (198.51.100.2) must act only as a backup for a default route learned dynamically via OSPF (AD 110). Fix the IPv6 static route and set a suitable AD (200) on the IPv4 default route.
Hard98You are connected to R1. Configure OSPFv3 for IPv6 so that R1 and R2 can exchange IPv6 routes over their directly connected link. Enable IPv6 routing, assign OSPFv3 process and area on the interface, and verify that the neighbor adjacency forms and routes appear in the IPv6 routing table.
Hard99A company wants to connect two sites across an IP network by creating a logical tunnel between the edge routers. Which technology is most directly associated with that requirement?
Hard100A network engineer adds a loopback interface Lo0 with IP address 172.16.0.1/32 to router R1. After restarting the OSPF process, the OSPF router-ID changes from 10.1.1.1 to 172.16.0.1, and the neighbor relationship with R2 resets. What should the technician do next to prevent this disruption the next time a loopback is added?
Hard101An OSPF-enabled router R1 fails to advertise the 192.168.50.0/24 network to neighbor R2, even though the neighbor relationship is up. Which misconfiguration on R1 would cause this?
Hard102Exhibit: A router has the following routes in its routing table: - OSPF: 10.1.1.0/24 - Static: 10.1.1.128/25 - Default: 0.0.0.0/0 A packet is destined for 10.1.1.130. Which route does the router use?
Hard103Which Cisco IOS command configures a default static route pointing to next hop 203.0.113.1?
Easy104A route to 10.10.20.0/24 disappears when an OSPF adjacency fails. Which design would most directly provide an automatic backup without changing the primary OSPF path during normal operation?
Hard105Exhibit: R1 has a static default route to 192.0.2.2 and also learns a default route from OSPF. Which default route is installed in the routing table?
Medium106You are configuring a Cisco router that connects to an ISP through two different providers. The primary path is learned dynamically through OSPF, and the backup path is a static route pointing to a next-hop of 203.0.113.1. You need the static route to remain in the routing table only when the OSPF-learned default route is unavailable. Which configuration should you apply?
Medium107A router has the following routes in its routing table: a static route to 10.1.1.0/24 with administrative distance 1, an OSPF route to 10.1.1.0/24 with administrative distance 110, and an EIGRP route to 10.1.1.0/24 with administrative distance 90. A packet arrives destined for 10.1.1.50. Which route will the router use to forward the packet?
Hard108You are connected to R1. Configure HSRP so that R1 becomes the active router for VLAN 10, with a virtual IP of 192.168.10.1. Ensure that R1 preempts if it comes back online after a failure. Also, configure R1 to decrement its HSRP priority by 20 if its GigabitEthernet0/1 interface goes down. The current configuration shows both routers as active — identify and fix the issues.
Hard109Which OSPF component is used to identify routers uniquely inside an OSPF domain?
Easy110Based on the exhibit, why is traffic to host 198.51.100.70 using the OSPF route instead of the static route?
Hard111What is the best explanation for why a router chooses the OSPF route to 10.50.0.0/16 instead of the RIP route?
Hard112Why is RIP rarely chosen for large modern enterprise networks?
Medium113Why is a default route often called a route of last resort?
Medium114Based on the exhibit, which command is the best next step to verify whether the floating static route becomes active after the primary route is lost?
Hard115You are verifying OSPF operation on router R1. After confirming that OSPF is configured on the correct interfaces, which command should you use next to directly check whether R1 has established a neighbor adjacency with another OSPF router?
Hard116Exhibit: R1 can ping 10.1.23.2 but cannot ping 192.168.3.10 behind R3. The routing table on R1 lacks 192.168.3.0/24. What is the best next check?
Medium117Which two statements accurately describe longest-prefix match?
Medium118A network technician is troubleshooting a router-on-a-stick configuration. R1 has sub-interface G0/0.10 with encapsulation dot1q 10 and IP 192.168.10.1/24, and sub-interface G0/0.20 with encapsulation dot1q 20 and IP 192.168.20.1/24. Hosts in VLAN 10 cannot reach hosts in VLAN 20. The physical interface G0/0 is up and no shutdown. Both sub-interfaces show up/up. What should the technician do next?
Hard119You are connected to R1. The network currently uses a static default route pointing to ISP1 (198.51.100.1) via GigabitEthernet0/0. However, the backup link to ISP2 (203.0.113.1) via Serial0/0/0 has a floating static default route with an administrative distance of 130. The backup route is not taking over when the primary link fails. Configure the floating static route correctly so that it becomes active when the primary route is lost, and verify that the routing table shows the backup default route with the appropriate next-hop.
Hard120Based on the exhibit, what is the most likely reason the PPP link is down?
Hard121What metric does RIP use to choose the best path?
Easy122R1 and R2 are directly connected and running OSPF. They can ping each other, the area matches, and the timers match, but they still do not become neighbors. What is the most likely cause?
Hard123A network administrator configures OSPF on two routers, R1 and R2, connected via their Serial0/0/0 interfaces (IP addresses 10.1.1.1/30 and 10.1.1.2/30). They verify that both routers use the same OSPF process ID and area 0, but R1's 'show ip ospf neighbor' shows no adjacencies. Given the partial exhibit from R1, what is the most likely cause of the adjacency failure and its correct solution?
Hard124Which TWO statements accurately describe OSPFv3 configuration and verification for IPv6?
Medium125Drag and drop the following steps into the correct order. Configure the router in this sequence: an IPv4 static route, then an IPv6 static route, then an IPv4 default route together with a floating static backup route (higher administrative distance), and finally verify with show ip route and show ipv6 route.
Medium126A router learns the same prefix from both OSPF and EIGRP. Which route is installed by default?
Medium127R1 and R2 are connected via a GigabitEthernet link in the same IPv4 subnet, and both routers have OSPF configured in the same area. However, R1 is not learning any OSPF routes from R2. What is the most likely cause?
Hard128Which TWO statements correctly describe how a router selects the best path for a destination network when multiple routing table entries exist?
Medium129A router learns 203.0.113.0/24 through OSPF and 203.0.113.0/25 through a static route. Which route is used for traffic destined to 203.0.113.10?
Medium130A router has two static routes to the same destination network: one with administrative distance 1 and another with administrative distance 200. Both routes are configured with the same next-hop address. What will the router do with these routes?
Medium131Refer to the exhibit. A network engineer is troubleshooting connectivity to server 10.10.10.130. The routing table contains both a static route and an OSPF route for overlapping prefixes. The engineer examines the specific routing entry for 10.10.10.130. Based on the output, why does the router choose the route via 10.1.1.2 instead of the OSPF route via 10.2.2.2 (for 10.10.10.0/24)?
Hard132A network engineer is troubleshooting a router that is not forwarding traffic to a remote network. The router has a static route configured for that network, but the next-hop address is not directly connected and is not reachable via any other route. What is the most likely cause of the problem?
Hard133A router has routes to 192.168.100.0/24 and 192.168.100.128/25. Which route is used for traffic to 192.168.100.140?
Hard134Based on the exhibit, why is the static route not being used for 172.18.9.10?
Hard135Which three statements about IPv6 routing are correct? (Choose three.)
Medium136Two routers, R1 and R2, have been configured with HSRP for VLAN 10 to provide default gateway redundancy to hosts. The virtual IP address is 192.168.10.1. After configuration, end hosts report inconsistent connectivity to the gateway, and a failover test reveals that when the active router is shut down, connectivity is lost. The network administrator checks the HSRP status on both routers. R1 shows HSRP group 10 as Active with no standby router, and R2 shows HSRP group 20 as Active with no standby router. What is the most likely cause of the redundancy failure?
Hard137You are configuring a Cisco router that connects to an ISP via a serial link. The ISP has assigned the next-hop address 203.0.113.1 for all Internet-bound traffic. You need to ensure that the router forwards all traffic for unknown destinations to this next-hop, but you do not want to use a fully specified static route. Which command should you use?
Medium138Why is R1 not installing the floating static default route into the routing table?
Hard139Drag and drop the following steps into the correct order for the router's routing table lookup process when forwarding a packet to a destination IP address, including the best-path selection logic.
Hard140Which two statements accurately describe OSPF route selection or behavior at the CCNA level?
Medium141Drag and drop the following OSPFv2 neighbor state transitions into the correct order, starting from the initial Down state on a broadcast or point-to-point network (non-NBMA).
Medium142A network engineer configures a primary default route via Gi0/0 (next-hop 192.168.12.2) and a floating static default route via Gi0/1 (next-hop 192.168.12.6) with AD 200. To test failover, the engineer issues the shutdown command on Gi0/0. After this, the router does not have a default route in the routing table. Which problem explains this behavior?
Hard143Drag and drop the following steps into the correct order to configure and verify OSPFv3 on R1 GigabitEthernet0/0 (which already has an IPv6 address and therefore a link-local address) in area 0. R1 has no IPv4 addresses, so a router ID must be set manually. Enable routing, create the process with its router ID, then configure the interface, then verify.
Medium144Which static route on R1 sends all unknown IPv4 destinations to next-hop address 192.0.2.1?
Easy145Drag and drop the following steps into the correct order to configure and verify HSRP on an interface. Configure in this sequence: the interface IP address, the HSRP group and virtual IP, the priority, then preemption, and finally verify.
Medium146A router has routes to 192.168.0.0/16 and 192.168.50.0/24. Which route is used for traffic to 192.168.50.99?
Hard147Refer to the exhibit. A network administrator is troubleshooting why not all OSPF neighbors are fully adjacent on a multi-access broadcast segment. After issuing the show ip ospf neighbor command on R1, the output is displayed. What is the most likely cause of the 2WAY/DROTHER state for neighbor 172.16.1.1?
Hard148A network engineer configures a static route: ip route 192.168.10.0 255.255.255.0 10.1.1.2. The next hop 10.1.1.2 is reachable via OSPF. Later, the engineer notices that the route to 192.168.10.0/24 has disappeared from the routing table. What is the most likely cause?
Hard149A router advertises its LAN network into OSPF, but no OSPF Hellos should be sent toward end-user devices on that LAN. Which configuration approach solves this cleanly?
Medium150Match each route source or route type to its most accurate description.
Medium151Which OSPF network type on Ethernet performs a DR and BDR election by default?
Medium152Why is a default route useful on a small branch router connected to a single upstream provider?
Medium153A router has an OSPF-learned route to a destination prefix and also a directly connected route to a broader supernet that includes that destination. The OSPF route is more specific. Which route is used for the destination?
Hard154Why is a default route often described as a route of last resort?
Medium155You have console access to both R1 and R2. Configure OSPFv2 on both routers to establish a single-area adjacency in area 0. The link between R1 and R2 uses 10.0.0.0/30. Currently, OSPF is not configured on either router. After configuration, verify the adjacency forms and routes are exchanged.
Hard156Refer to the exhibit. R1 and R2 are directly connected and both configured for OSPF area 0. The IP addresses are correct and in the same subnet, but the routers do not become neighbors. What is the most likely cause?
Hard157Drag and drop the following steps into the correct order to configure HSRP on the intended active router, verify the election, and test failover. Configure the virtual IP first, then the priority, then preempt.
Medium158Exhibit: OSPF neighbors are not reaching FULL state on an Ethernet segment with multiple routers. The output of show ip ospf neighbor on R2 shows a neighbor in the 2WAY/DROTHER state. What is the most likely reason?
Hard159An engineer configures a floating static route to 0.0.0.0/0 with an administrative distance of 200 while OSPF is providing a default route. What is the intended behavior?
Hard160A router learns the same destination from EIGRP and OSPF. The EIGRP route has a metric of 1000, and the OSPF route has a metric of 10. Which route is installed by default?
Hard161A router learns 172.16.0.0/16 from OSPF and 172.16.10.0/24 from a static route. Which route is used for traffic to 172.16.10.55?
Hard162Drag and drop the following steps into the correct order to configure and verify HSRP version 2 on a router interface. Set the HSRP version before defining the group, then configure the virtual IP, then the priority, then preempt.
Medium163Which TWO statements correctly describe OSPFv2 router-id selection and verification in a single-area configuration?
Medium164Drag and drop the following steps into the correct order to configure and verify OSPFv3 for IPv6 on a Cisco router. Enable IPv6 routing first.
Medium165A router learns a route to 172.16.0.0/16 via OSPF (administrative distance 110) and a route to 172.16.10.0/24 via EIGRP (administrative distance 90). No other overlapping routes exist. Which TWO statements about how the router handles these routes are correct?
Medium166Which TWO statements about IPv4 and IPv6 static routes, including floating static routes, are correct?
Medium167R1 cannot reach host 10.3.3.1 on R3. The technician checks routing: R1 has a route to 10.3.3.0/24 via next-hop 10.1.1.2 (R2). R2 has a route to 10.3.3.0/24 via next-hop 10.2.2.2 (R3). No ACLs are applied on any of the routers. A ping from R1 to 10.3.3.1 times out. A ping from R2 to 10.3.3.1 succeeds. What should the technician do next?
Hard168R1 has the following static route configured: ip route 0.0.0.0 0.0.0.0 203.0.113.1 What does this route accomplish?
Medium169R1 and R2 are connected via Ethernet and are configured with OSPF, but they fail to form an adjacency. Upon checking the interface configurations, you see that R1’s interface is in OSPF area 0 while R2’s interface is in area 1, and both interfaces use default timers and are in the same subnet. What is the most likely reason?
Hard170Drag and drop the following steps into the correct order to describe the router's routing table lookup process for a destination IP address, including the best-path selection logic (longest prefix match, then administrative distance, then metric) and the final forwarding decision.
Medium171A router has a connected route to 192.168.1.0/24 and also has a default route. Which route is used for traffic to 192.168.1.55?
Hard172Which three of the following statements about the routing table lookup process on a Cisco router are true? (Choose three.)
Medium173Exhibit: R1 has the static route 'ip route 0.0.0.0 0.0.0.0 192.0.2.2 200' and also learns a default route from OSPF. Which default route will be installed while the OSPF route is present?
Hard174A router shows the following route: O 10.10.40.0/24 [110/20] via 192.0.2.2, 00:00:12, GigabitEthernet0/0 What does the value 110 represent?
Hard175A network engineer notices that R1 is using the static route to 192.168.10.0/24 via next-hop 10.1.1.2 instead of the OSPF route via 10.2.2.2, even though the OSPF path has lower latency. What is the most likely cause?
Hard176You are connected to R1 via console. R1 is an area border router. Its three LAN subnets 10.0.1.0/24, 10.0.2.0/24 and 10.0.3.0/24 are in OSPF area 0. The serial link to R2 uses subnet 10.0.4.0/30 and is in OSPF area 1. The network administrator wants R1 to advertise a single summary route for the three LAN subnets into area 1, reducing the size of the link-state database in area 1. R1 is already running OSPF with network statements for its connected subnets in their respective areas. Configure the route summarization on R1.
Medium177You are connected to R1 via the console. The network currently uses EIGRP as its IGP, but you recently configured a static default route toward R2 (next-hop 203.0.113.2) to reach the Internet. However, traffic from R1 to the Internet is not taking the expected path. Examine the provided routing table and partial configuration, then fix the issue so that the static default route is used only when the EIGRP-learned default route is unavailable.
Hard178You are connected to R1. Configure OSPFv2 on R1 and R2 so that they form a full adjacency and can exchange routes. The current configuration has mismatched hello/dead timers blocking the adjacency. Adjust only the necessary settings on R1 to match R2's OSPF timers.
Hard179Which TWO statements about floating static routes and default routes are correct?
Medium180Drag and drop the following steps into the correct order to configure and verify HSRP on the router that should be active. The interface IP address is already configured. Configure the virtual IP first, then the priority, then preempt.
Medium181You are connected to R1 via console. R1 and R2 are directly connected via GigabitEthernet0/0 and both run OSPF process 1 in area 0 (R1 router-id 1.1.1.1, R2 router-id 2.2.2.2), but they do not form an adjacency. R2 uses the default OSPF timers on the link. R1 must also not send OSPF hellos out of its GigabitEthernet0/1 interface. Use the exhibit to find and fix the issue on R1.
Hard182Based on the exhibit, why is traffic to 192.168.40.200 using the default route instead of the intended static route?
Hard183Two directly connected routers, R1 and R2, are configured with single-area OSPF in Area 0. The administrator notices that they are not forming a full OSPF neighbor adjacency. The exhibit displays relevant portions of the running configurations. What is the most likely cause of the problem?
Hard184Refer to the exhibit. A network engineer is troubleshooting an OSPF adjacency issue between R1 and R2. The output of the show ip ospf neighbor command on R1 shows the neighbor relationship with R2 stuck in the EXSTART/DROTHER state. What is the most likely cause?
Hard185You are connected to R1 via console. R1 has three directly connected subnets: 192.168.1.0/24 (G0/0), 192.168.2.0/24 (G0/1), and 192.168.3.0/24 (G0/2). Configure a single static summary route to Null0 that covers all three subnets using the smallest (most specific) summary prefix possible, so that traffic matching the summary but no more specific route is discarded and routing loops are avoided.
Medium186A branch router learns a route to 10.20.30.0/24 from OSPF with metric 30 and also has a static route to the same prefix with an administrative distance of 5. Which route will appear in the routing table?
Medium187You are connected to R1 via the console. R1 is a new router that connects to three subnets: 192.168.1.0/24 (connected to GigabitEthernet0/0), 192.168.2.0/24 (connected to GigabitEthernet0/1), and 192.168.3.0/24 (connected to GigabitEthernet0/2). R1 must be able to ping the loopback0 interface of R2 (192.168.100.1/32) which is reachable via R2's Serial0/0/0 interface (10.0.0.2/30). The link between R1 and R2 is 10.0.0.0/30, with R1's interface being 10.0.0.1/30. No dynamic routing protocols are configured. Configure R1 to reach the loopback address of R2 using a host-specific static route (not a default route).
Medium188Which summary route best represents these four networks? 10.20.0.0/24 10.20.1.0/24 10.20.2.0/24 10.20.3.0/24
Hard189Drag and drop the following steps into the correct order to describe the router's routing table lookup process for a destination IP address, including best-path selection using longest prefix match, administrative distance, and metric.
Medium190A router has a static route to 10.20.20.0/24 and also has a default route. Which route is used for traffic to 10.20.20.8?
Hard191You are connected to R1 via the console. R1 and R2 must form a full OSPFv2 adjacency in area 0 over the 203.0.113.0/30 link (R1 G0/0 203.0.113.1/30, R2 G0/0 203.0.113.2/30). R1's router-id is 1.1.1.1 and R2's is 2.2.2.2. R1 uses passive-interface default, which currently makes G0/0 passive so no hellos are sent. Fix the adjacency while keeping R1's Loopback0 (203.0.113.129/32) passive, then verify the neighbor state and routes.
Hard192Which two statements accurately describe route summarization?
Medium193Refer to the exhibit. A network engineer notices that traffic from R1 to the 10.1.0.0/16 network is taking a longer path than expected despite OSPF being the only routing protocol. The engineer examines the OSPF LSDB on R1 to investigate. Based on the output, what is the most likely cause of the suboptimal routing?
Hard194An enterprise network uses an IPv6 dual-stack design. Router R1 has a primary default route ::/0 via 2001:db8:1::1 with AD 1 and a floating default route with AD 10 via link-local address fe80::2. After the primary link fails, the floating route fails to install, and R1 loses all external connectivity. The administrator confirms the backup interface is up/up.
Hard195Refer to the exhibit. Router R1 reaches its OSPF neighbor and internal networks, but cannot reach hosts on the internet. R1 connects to an ISP router at 203.0.113.1 through GigabitEthernet0/2. What is the most likely cause?
Hard196R1 has routes to 172.16.10.0/24 from multiple sources. Which route will be installed?
Hard197Drag and drop the following steps into the correct order to describe the router's routing table lookup process from receiving a packet with a destination IP address to making the forwarding decision, including best-path selection criteria.
Medium198A router has learned the following candidate routes for the same destination (before best-path selection): O 10.10.50.0/24 [110/20] via 192.168.12.2, GigabitEthernet0/0 D 10.10.50.0/24 [90/30720] via 192.168.13.2, GigabitEthernet0/1 Which route will become the active route in the routing table?
Hard199A static default route is configured on R1 toward ISP-A, and a second default route toward ISP-B is configured with a higher administrative distance. Which two statements are correct during normal operation and after ISP-A failure?
Hard200Which three of the following are valid features of Enhanced Interior Gateway Routing Protocol (EIGRP)? (Choose three.)
Medium201You are connected to R1, which must become an OSPFv3 neighbor of R2 over G0/0 and learn R2's loopback route (2001:db8:1:2::2/128, advertised as a host route). The legacy OSPFv3 process is configured, but IPv6 routing is not enabled globally and OSPFv3 is not enabled on the interface. Configure R1 and verify the neighbor state and routing table.
Hard202Exhibit: An OSPFv2 adjacency between two routers on Ethernet is not forming. Which two mismatches would directly prevent the routers from becoming neighbors?
Hard203Refer to the exhibit. A network administrator is troubleshooting an OSPF adjacency on R1's GigabitEthernet0/0 interface connected directly to R2. R2 is powered on and shows correct OSPF configuration, but the adjacency is stuck in the INIT or DOWN state. Based on the output, what is the most likely cause of the failure?
Hard204You are connected to R1 via console. R1 is connected to three routers (R2, R3, R4) over Ethernet links, all in OSPF area 0. Due to network topology, R1 should not become the Designated Router (DR) or Backup Designated Router (BDR) on any of its interfaces. You need to configure R1's OSPF priority appropriately to ensure it never participates in DR/BDR elections.
Medium205A network engineer notices that traffic from the router to server 192.168.10.5 is being sent over a slow backup link, even though the primary high-speed link is up. The routing table has an OSPF route for 192.168.10.0/24 via the primary link and a static host route to 192.168.10.5/32 via the backup link. Why is the backup link used for traffic to the server?
Hard206An OSPF-enabled router has two paths to the same destination network, and both paths have the same OSPF cost. What is the most likely default behavior?
Hard207Exhibit: R1 has a default route pointing to 10.1.1.2. Users lose internet access when that next hop fails, even though a floating static backup exists. Why is the backup not installed?
Hard208R1 reaches 192.168.20.0/24 through OSPF (AD 110) with a floating static route (AD 200) as backup. R2's GigabitEthernet0/0 flapped, and R1 switched to the floating static route. The interface has been up/up for 15 minutes, but R1's routing table still shows the static route and not the OSPF route. What should the technician do next?
Hard209An engineer wants a static route to be used only if the OSPF route to the same network disappears. What should be configured?
Hard210A network engineer is configuring a Cisco router that must forward all traffic destined to unknown networks to the next-hop 192.0.2.1. The engineer enters the command ip route 0.0.0.0 0.0.0.0 192.0.2.1. After this configuration, which routing table entry will be created?
Easy211Match each route source on the left to its default administrative distance and description on the right.
Medium212Refer to the exhibit. R1 connects to R2 on GigabitEthernet0/1 (10.1.1.0/24) and to R3 on GigabitEthernet0/2 (10.1.2.0/30). R3 is supposed to advertise 192.168.30.0/24 in OSPF area 0, but R1 has no such route. Based on the output, what is the most likely cause?
Hard213Refer to the exhibit. A static default route was configured on branch router R1, but a ping to 8.8.8.8 fails. The output of show ip route and the relevant configuration are shown. What is the most likely cause?
Hard214Two directly connected routers running OSPFv3 do not form an adjacency. Both interfaces have valid IPv6 addresses and can ping each other using link-local addresses. What is the most likely cause?
Hard215You are connected to R1 via console. Configure OSPFv3 for IPv6 in area 0 on R1 and R2 so that the IPv6 loopbacks on both routers can communicate. R1's GigabitEthernet0/0 and R2's GigabitEthernet0/1 are directly connected (2001:db8:12::/64). Neither router has an IPv4 address, so configure router IDs 1.1.1.1 (R1) and 2.2.2.2 (R2). Enable OSPFv3 on the correct interfaces and verify neighbors and routes.
Hard216You are connected to R1. R1 G0/0 (10.0.0.1/30, 2001:db8:1::1/64) connects to R2 (10.0.0.2, 2001:db8:1::2), and G0/1 connects to the LAN. R1 normally learns 192.0.2.0/24 through OSPF (AD 110). Configure IPv4 and IPv6 default routes toward R2, and replace the existing static route for 192.0.2.0/24, which uses R1's own G0/0 address as its next hop, with a floating static route via R2 using an administrative distance of 130 so it is used only if the OSPF route disappears.
Hard217You are connected to multilayer switch MLS1. It should use 192.0.2.2 (reachable through Vlan10) as its primary IPv4 default gateway and 198.51.100.2 (through Vlan20) as a floating backup default route with an administrative distance of 10. It should also have an IPv6 host route for 2001:db8:1::10/128 via next hop 2001:db8:1::1 (on the Vlan10 segment). The exhibit shows that both IPv4 default routes are active at once and that the IPv6 host route is missing from the routing table. Fix both problems.
Hard218A router has the following routes in its routing table: a static route to 10.60.4.16/28, an OSPF route to 10.60.4.0/24, and an EIGRP route to 10.60.0.0/16. Which route will be used for a packet destined to 10.60.4.17?
Hard219You are connected to R1. R1 must reach the Internet through R4 (IPv4 next hop 203.0.113.2, IPv6 next hop 2001:db8:203:0:113::2) as the primary path. A backup floating static default route with administrative distance 200 must exist for IPv4 only, using R3 (next hop 198.51.100.2). R1 currently has only the floating IPv4 default route and an IPv6 default route that points to the wrong next hop (R3, 2001:db8:198:51:100::2). Fix the configuration.
Hard220A PC cannot reach a server at 10.1.1.5. The server is only reachable through R3 (192.168.13.3), which R1 learned through OSPF. An engineer reviews the routing table on R1 and finds that traffic to the server is being sent toward 192.168.12.2 instead. Based on the exhibit, what is the most likely cause of the problem?
Hard221A network engineer configures OSPF between R1 and R2, but the routers never become neighbors on GigabitEthernet0/0. Based on the exhibit, what is the most likely cause?
Hard222A router has a static route and a RIP route for the same destination prefix. What is the primary reason the static route is preferred over the RIP route?
Hard223You are connected to R1, a multilayer switch that should be the HSRP active gateway for VLAN 100 with virtual IP 192.168.100.1 (R2 already uses 192.168.100.1 in group 100). R1 and R2 both show as Active, because R1's virtual IP does not match. R1 has default priority, no preempt, and no tracking. Configure HSRP group 100 on R1 to fix the virtual IP, set priority 110, enable preempt, and track GigabitEthernet0/1 with a decrement of 20.
Hard224After configuring a static discard route with the command 'ip route 0.0.0.0 0.0.0.0 Null0 254' on R1, a network engineer finds that traffic to destinations that are not in the routing table is still being forwarded out to the ISP instead of being dropped. What is the most likely cause?
Hard225You are troubleshooting a network connectivity issue on R1. The network 192.168.10.0/24 behind R2 must be reachable from R1 via the primary path through R2 (192.0.2.2). A backup path via R3 (198.51.100.2) should automatically take over if the primary fails. Currently, traffic to 192.168.10.0/24 is incorrectly using the backup path even though the primary path is operational. Analyze the routing table and configuration, then fix the issue so that the primary path is preferred when available.
Hard226Which two statements accurately describe why BGP is often relevant at an Internet or multi-provider edge?
Medium227A router has routes to 172.20.0.0/16, 172.20.10.0/24, and 172.20.10.64/26. Which route is used for traffic to 172.20.10.70?
Hard228You are connected to R1. R1 and R2 cannot form an OSPF adjacency on 10.0.0.0/30. R1 has network 10.0.0.0 0.0.0.3 in area 1 with the default hello (10) and dead (40) timers. R2 has the same network in area 0 with hello-interval 5 and dead-interval 20. R2 is correct (area 0 is the backbone and 5/20 is the standard on the rest of the network), so change only R1 to match R2.
Hard229What problem do first-hop redundancy protocols such as HSRP solve?
Medium230A router has routes for 10.10.0.0/16, 10.10.20.0/24, and a default route. Which route is used for destination 10.10.20.55?
Medium231A router has a static route to 10.30.5.128/25, an OSPF route to 10.30.5.0/24, and a default route 0.0.0.0/0 in its routing table. Which route will the router use for destination 10.30.5.130?
Hard232Which TWO statements are true about OSPFv2 neighbor adjacency, network statements, and passive interfaces?
Medium233Refer to the exhibit. An engineer expects all traffic destined to the 10.10.10.0 network to be forwarded via 10.1.1.2. However, when testing connectivity to host 10.10.10.64, traffic is being sent to 10.2.2.2 instead. What is the most likely cause?
Hard234A router learns 172.16.40.0/24 from OSPF with AD 110 and metric 20. It also learns the same prefix from EIGRP with AD 90 and feasible distance 30720. Which route is installed?
Medium235A router interface is configured for OSPF, but neighbors do not form. The engineer checks the interface and sees Hello 10 and Dead 40. The neighbor on the same segment uses Hello 30 and Dead 120. What is the most likely cause of the OSPF adjacency failure?
Medium236A router has these routes installed. Which path will be chosen for traffic to 172.16.10.200?
Hard237Why is route summarization useful at a distribution layer or area boundary?
Medium238A static default route is configured with an administrative distance of 250. What is the most likely design intention?
Hard239You are connected to R2. Single-area OSPFv2 (all interfaces in area 0 with default timers) is being deployed on R1, R2 and R3. R2's G0/0 to R1 has non-default hello and dead timers, and R2's network statement for the link to R3 (10.0.23.0/30) places it in area 1 while R3 uses area 0. Correct R2 so that both adjacencies form.
Hard240Which two statements accurately describe passive interfaces in OSPF?
Medium241Exhibit: R3 learns 10.50.0.0/16 by OSPF through two equal-cost paths. What will R3 do by default?
Hard242A branch router uses PPP on a serial WAN link. Which additional PPP capability most directly improves access security on that link?
Hard243A router has a default route and a specific route to 203.0.113.0/24. Which route is used for traffic to 203.0.113.25?
Hard244A network engineer needs a floating static route to back up an OSPF-learned route. Which two configurations are necessary for the static route to remain unused until OSPF fails?
Medium245Exhibit: R1 has learned 10.50.0.0/24 through OSPF and also has a floating static route to the same prefix with administrative distance 130. Which route is installed while OSPF is healthy?
Medium246Which two statements accurately describe floating static routes?
Medium247Two routers are in the same OSPF area and on the same subnet, but they do not form an adjacency. One interface uses a hello interval of 10 seconds and the other uses 5 seconds. What is the most likely cause?
Hard248You are configuring a default route on R1 to send all unknown traffic to the next-hop 203.0.113.1. However, you want this route to be used only if the primary default route learned via OSPF is unavailable. Which command should you use?
Medium249A branch router is running single-area OSPF. An engineer wants an interface to advertise its connected network into OSPF but must prevent hello packets from being sent on that LAN segment. Which two actions achieve that goal?
Medium250Exhibit: A static route to 172.16.40.0/24 is configured, but traffic still follows the default route. Which two explanations are plausible?
Hard251On a broadcast multiaccess segment, R3 has an OSPF priority of 200, but it is in the DROTHER state. Which explanation best fits OSPF behavior?
Hard252Which TWO statements accurately describe the behavior and configuration of floating static routes?
Medium253A network administrator needs to configure a static route on a Cisco router to reach the 192.168.50.0/24 network through next-hop 10.1.1.2, using the default administrative distance. Which command accomplishes this?
Easy254A network engineer is troubleshooting an OSPFv3 adjacency issue between two directly connected routers. Both routers are configured for OSPFv3 in area 0 on their GigabitEthernet0/0 interfaces. The engineer checks the OSPFv3 neighbor status on R1 and sees that the neighbor state is stuck in EXSTART. The engineer verifies that both interfaces are up and have IPv6 link-local addresses. What is the most likely cause of this problem?
Hard255A packet is destined for 192.168.40.130. The routing table contains 192.168.40.0/24, 192.168.40.128/25, and 0.0.0.0/0. Which route is used?
Hard256Two OSPF routers connected over Ethernet fail to become neighbors. Their interfaces are up/up and in the same IPv4 subnet. One router uses area 0 and the other uses area 1 on the connecting interfaces. What is the most likely cause?
Hard257An administrator configures a GRE tunnel interface on a router as shown in the exhibit (Tunnel0 sourced from GigabitEthernet0/0 with tunnel destination 198.51.100.2). What is the main purpose of this configured tunnel?
Hard258Drag and drop the following OSPFv2 neighbor state transitions into the correct order, starting from the initial state when no neighbor information has been received.
Medium259Why is traffic to 10.10.10.200 using the EIGRP route instead of the OSPF route, given that both routes have the same prefix length?
Hard260Which TWO statements about IPv4/IPv6 static routing are true?
Medium261Based on the exhibit, what is the most likely reason the PPP link is failing to authenticate?
Hard262A router has the following routes in its table: 172.16.0.0/16, 172.16.20.0/24, and 172.16.20.128/25. Which route is used for traffic to 172.16.20.200?
Hard263A router has a directly connected route to 10.1.1.0/24 and a static default route. Which route is used for traffic to 10.1.1.200?
Hard264You are connected to R1 via the console. R1 connects two subnets, 192.168.1.0/24 on GigabitEthernet0/0 and 192.168.2.0/24 on GigabitEthernet0/1, and reaches ISP routers 203.0.113.1 and 203.0.113.2 through GigabitEthernet0/2. A default route points to 203.0.113.1, but policy requires traffic from 192.168.1.0/24 to the Internet to use next hop 203.0.113.2. Traffic between the two internal subnets must keep using normal routing, and all other traffic uses the default route. Implement policy-based routing on R1.
Hard265Refer to the exhibit. A network engineer is verifying OSPF routing on R1. All routers in the topology are expected to reside in OSPF area 0, and the network 172.16.0.0/16 should be advertised from R2 within the same area. The engineer issues the show ip route 172.16.0.0 command on R1 and sees the output in the exhibit. The engineer expected to see an intra-area route (O) instead of an inter-area route (O IA). What is the most likely cause of this discrepancy?
Hard266R1 and R2 are connected via a shared Ethernet segment. Both routers are configured in OSPF area 0 and are on the same IP subnet. OSPF authentication is enabled on both interfaces, but the adjacency is not forming. What is the most likely reason?
Hard267R3 has the static route shown in the exhibit. Packets destined for 172.20.8.0/24 are being dropped. What is the most likely cause?
Medium268What is an autonomous system in basic BGP terminology?
Medium269Drag and drop the following OSPFv2 neighbor states into the correct order for a new router forming a full adjacency with the DR on a multi-access network.
Medium270A network engineer configures R1 and R2 as shown in the exhibit, but R1 cannot form an OSPF adjacency with R2 on interface GigabitEthernet0/0. What is the most likely cause of the failure?
Medium271An administrator has just configured OSPF in a single area between router R1 and router R2, which are directly connected via their Gi0/0 interfaces with IP addresses 10.0.0.1/30 and 10.0.0.2/30. On R1, the command show ip ospf neighbor shows no entries, and a further check on R2 with show ip ospf interface gi0/0 indicates that the interface is passive. Which configuration error is most likely causing the adjacency failure?
Hard272An ABR connects Area 0 and Area 1. Area 1 contains the subnets 10.1.1.0/24, 10.1.2.0/24 and 10.1.3.0/24. The engineer enters 'area 1 range 10.1.0.0 255.255.252.0' under the OSPF process on the ABR. Which statement describes the result for routers in Area 0?
Hard273On a broadcast segment, R1 is the DR (priority 100), R2 is the BDR (priority 1), and R3 is a DROther (priority 200) that was powered on after the election. R1's GigabitEthernet0/0 is shut down for maintenance. Which statement describes what OSPF does next?
Hard274Drag and drop the following commands into the correct order to configure OSPFv3 for IPv6 on a Cisco IOS-XE router using the address-family style. Enable IPv6 routing first, then create the process and its router ID, then enable OSPFv3 on the interface.
Medium275R1 and R2 are directly connected via Ethernet on interface G0/0. Both interfaces are in the same subnet and configured for OSPF area 0. After enabling OSPF, R1 never lists R2 as an OSPF neighbor. What is the most likely cause?
Hard276A router has a static route configured as shown in the exhibit. The output of show ip interface brief shows that the exit interface, Serial0/0/0, is administratively down. Why is the route to 10.200.0.0/16 present in the running configuration but absent from the routing table?
Hard277A network engineer is troubleshooting OSPFv3 adjacency between R1 and R2, two directly connected Cisco IOS-XE routers. R1 connects to R2 through GigabitEthernet0/0. The engineer configured OSPFv3 on both routers, but 'show ospfv3 neighbor' on R1 shows no neighbors. Based on the output, what is the most likely cause?
Hard278A route table shows both a default route and a more specific route to 192.168.50.0/24. Which two statements describe how packets destined for 192.168.50.25 are handled?
Medium279Which TWO statements about interpreting routing table output are true? (Choose two.)
MediumOther domains
All 200-301 exam domains
Frequently asked questions
- What does the IP Routing domain cover on the 200-301 exam?
- Be able to read a routing table and decide which route installs and forwards a given destination. The single most important thing: longest-prefix match first, then administrative distance, then metric.
- How many questions are in this domain?
- This page lists all 279 IP Routing questions in the 200-301 question bank. The actual exam draws from this domain proportionally to its weighting in the official exam blueprint.
- What is the best way to practise this domain?
- Start with a short focused session (10 questions) to identify gaps, then work through explanations. Repeat with a longer session once the weak areas feel solid.
- Can I practise only IP Routing questions?
- Yes — the session launcher on this page filters questions to this domain only. Choose any session length for inline explanations and scoring.