EIGRP Troubleshooting

A network engineer runs the following command on Router R1:

R1# show ip eigrp neighbors

EIGRP-IPv4 Neighbors for AS(100) H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 10.1.1.2 Gi0/0 13 00:12:34 12 200 0 45 1 10.2.2.2 Gi0/1 12 00:10:20 15 200 0 32 2 10.3.3.2 Gi0/2 14 00:08:15 18 200 0 28 3 10.4.4.2 Gi0/3 13 00:06:10 20 200 0 22

Based on this output, which statement is correct?

A network engineer runs the following command on Router R1:

R1# show ip eigrp topology

EIGRP-IPv4 Topology Table for AS(100)/ID(192.168.1.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status

P 10.10.10.0/24, 1 successors, FD is 28160 via 10.1.1.2 (28160/28160), GigabitEthernet0/0 P 10.20.20.0/24, 1 successors, FD is 28160 via 10.2.2.2 (28160/28160), GigabitEthernet0/1 P 10.30.30.0/24, 1 successors, FD is 28160 via 10.3.3.2 (28160/28160), GigabitEthernet0/2 A 10.40.40.0/24, 0 successors, FD is Infinity via 10.4.4.2 (Infinity/Infinity), GigabitEthernet0/3

Based on this output, what is the problem?

A network engineer runs the following command on Router R1:

R1# show ip eigrp interfaces

EIGRP-IPv4 Interfaces for AS(100) Xmit Queue Mean Pacing Time Multicast Pending

Interface        Peers  Un/Reliable  SRTT   Un/Reliable   Flow Timer   Routes

Gi0/0 1 0/0 12 0/10 50 0 Gi0/1 1 0/0 15 0/10 50 0 Gi0/2 1 0/0 18 0/10 50 0 Gi0/3 1 0/0 20 0/10 50 0 Gi0/4 0 0/0 0 0/10 50 0

Based on this output, which statement is correct?

A network engineer runs the following command on Router R1:

R1# show ip eigrp traffic

EIGRP-IPv4 Traffic Statistics for AS(100) Hellos sent/received: 5000/4995 Updates sent/received: 150/148 Queries sent/received: 10/8 Replies sent/received: 8/10 Acks sent/received: 300/298 Input queue high water mark: 10 Input queue drops: 0 SIA-Queries sent/received: 0/0 SIA-Replies sent/received: 0/0 Hello process ID: 123 PDM process ID: 124 Socket queue: 0/2000/10/0 (current/max/highest/drops) Input queue: 0/2000/10/0 (current/max/highest/drops)

Based on this output, which statement is correct?

A network engineer runs the following command on Router R1:

R1# show ip eigrp neighbors detail

EIGRP-IPv4 Neighbors for AS(100) H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 0 10.1.1.2 Gi0/0 13 00:12:34 12 200 0 45 Version 12.0/2.0, Retrans: 0, Retries: 0, Restarts: 0 Topology ids from peer: 0 Passive interface: No Hello interval: 5 Hold time: 15

Based on this output, what is the problem?

A network engineer runs the following command on Router R1:

R1# show ip eigrp topology 10.10.10.0/24

EIGRP-IPv4 Topology Entry for AS(100)/ID(192.168.1.1) for 10.10.10.0/24 State: Passive, Reply status: 0, Originating router: 192.168.1.1 Routing Descriptor Blocks:

0.0.0.0 (Null0) from 0.0.0.0, Send flag: 0x0

Composite metric: (2560000000/0), Route is Internal Vector metric: Minimum bandwidth: 100000 Kbit Total delay: 100 microseconds Reliability: 255/255 Load: 1/255 Minimum MTU: 1500 Hop count: 0

Based on this output, what is the problem?

A network engineer runs the following command on Router R1:

R1# show ip eigrp topology all-links

EIGRP-IPv4 Topology Table for AS(100)/ID(192.168.1.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status

P 10.10.10.0/24, 1 successors, FD is 28160, Qos: 0 via 10.1.1.2 (28160/28160), GigabitEthernet0/0 via 10.2.2.2 (28672/28160), GigabitEthernet0/1 P 10.20.20.0/24, 1 successors, FD is 28160, Qos: 0 via 10.2.2.2 (28160/28160), GigabitEthernet0/1 via 10.3.3.2 (28672/28160), GigabitEthernet0/2

Based on this output, which statement is correct?

A network engineer runs the following command on Router R1:

R1# show ip eigrp interfaces detail Gi0/0

EIGRP-IPv4 Interfaces for AS(100)

Interface: GigabitEthernet0/0

Peers: 1 Xmit Queue Un/Reliable: 0/0 Mean SRTT: 12 Pacing Time Un/Reliable: 0/10 Multicast Flow Timer: 50 Pending Routes: 0 Hello interval: 5 Hold time: 15 Split horizon: Enabled Next multicast: 0.0.0.0 Next broadcast: 0.0.0.0

Based on this output, what is the problem?

A network engineer runs the following command on Router R1:

R1# show ip eigrp topology 10.50.50.0/24

EIGRP-IPv4 Topology Entry for AS(100)/ID(192.168.1.1) for 10.50.50.0/24 State: Active, Reply status: 0, Originating router: 192.168.1.1 Routing Descriptor Blocks:

10.1.1.2 (GigabitEthernet0/0), from 10.1.1.2, Send flag: 0x0

Composite metric: (4294967295/4294967295), Route is Internal Vector metric: Minimum bandwidth: 100000 Kbit Total delay: 100 microseconds Reliability: 255/255 Load: 1/255 Minimum MTU: 1500 Hop count: 1

Based on this output, what is the problem?

Consider the following EIGRP configuration on Router R1:

router eigrp 100
 network 10.0.0.0
 passive-interface default
 no passive-interface GigabitEthernet0/0

What is the effect of this configuration?

Given the following EIGRP configuration on Router R2:

router eigrp 200
 network 192.168.1.0
 network 10.0.0.0
 no auto-summary

Which statement is true about the operation of EIGRP?

Examine the following EIGRP configuration on Router R3:

interface GigabitEthernet0/1
 ip bandwidth-percent eigrp 100 50

What is the effect of this command?

Consider the following EIGRP configuration on Router R4:

router eigrp 300

variance 2

network 172.16.0.0

What is the purpose of the variance command?

Given the following configuration snippet on Router R5:

router eigrp 400
 network 10.1.1.0 0.0.0.255

What is wrong with this configuration?

Examine the following EIGRP configuration on Router R6:

interface GigabitEthernet0/2
 ip hello-interval eigrp 100 15
 ip hold-time eigrp 100 45

What is the effect of these commands?