Network Logging and Syslog

A network engineer runs the following command on Router R1:

R1# show logging

Syslog logging: enabled (0 messages dropped, 3 messages rate-limited, 0 flushes, 0 overruns, xml disabled, small buffer) Console logging: level debugging, 37 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level informational, 5 messages logged, xml disabled, filtering disabled

Logging Exception size (4096 bytes)

Count and timestamp logging messages: disabled Persistent logging: disabled

No active filter modules.

Trap logging: level informational, 0 message lines logged

Logging to 192.168.1.100 (udp port 514, audit disabled,

link up), 0 message lines logged, xml disabled, filtering disabled

Logging Source Interface: Loopback0

Log Buffer (4096 bytes):

*Mar  1 00:01:23.456: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Mar  1 00:02:34.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Based on this output, which statement is correct?

A network engineer runs the following command on Router R2:

R2# show logging | include %SYS-5-CONFIG_I

*Mar  1 00:10:15.123: %SYS-5-CONFIG_I: Configured from console by console
*Mar  1 00:12:45.678: %SYS-5-CONFIG_I: Configured from console by console
*Mar  1 00:15:30.001: %SYS-5-CONFIG_I: Configured from console by console
*Mar  1 00:20:00.999: %SYS-5-CONFIG_I: Configured from console by console

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R3:

R3# show logging | include %OSPF-5-ADJCHG

*Mar  1 00:05:10.123: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
*Mar  1 00:06:20.456: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired
*Mar  1 00:07:30.789: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from DOWN to INIT, Received Hello
*Mar  1 00:08:40.012: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from INIT to EXSTART, Event: start
*Mar  1 00:09:50.345: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from EXSTART to EXCHANGE, Event: Negotiation Done
*Mar  1 00:10:00.678: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from EXCHANGE to LOADING, Event: Exchange Done
*Mar  1 00:11:10.901: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
*Mar  1 00:12:20.234: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on GigabitEthernet0/0 from FULL to DOWN, Neighbor Down: Dead timer expired

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R4:

R4# show logging | include %BGP-3-NOTIFICATION

*Mar  1 00:01:05.123: %BGP-3-NOTIFICATION: sent to neighbor 10.0.0.2 4/0 (Hold Timer Expired) 0 bytes
*Mar  1 00:02:10.456: %BGP-3-NOTIFICATION: received from neighbor 10.0.0.2 4/0 (Hold Timer Expired) 0 bytes
*Mar  1 00:03:15.789: %BGP-3-NOTIFICATION: sent to neighbor 10.0.0.2 4/0 (Hold Timer Expired) 0 bytes

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R5:

R5# show logging | include %LINEPROTO-5-UPDOWN

*Mar  1 00:00:10.123: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Mar  1 00:00:20.456: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Mar  1 00:00:30.789: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Mar  1 00:00:40.012: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Mar  1 00:00:50.345: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Mar  1 00:01:00.678: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R6:

R6# show logging | include %SEC-6-IPACCESSLOGP

*Mar  1 00:01:15.123: %SEC-6-IPACCESSLOGP: list ACL_INBOUND denied tcp 10.0.0.100(12345) -> 192.168.1.1(80), 1 packet
*Mar  1 00:01:20.456: %SEC-6-IPACCESSLOGP: list ACL_INBOUND denied tcp 10.0.0.100(12346) -> 192.168.1.1(80), 1 packet
*Mar  1 00:01:25.789: %SEC-6-IPACCESSLOGP: list ACL_INBOUND denied tcp 10.0.0.100(12347) -> 192.168.1.1(80), 1 packet
*Mar  1 00:01:30.012: %SEC-6-IPACCESSLOGP: list ACL_INBOUND denied tcp 10.0.0.100(12348) -> 192.168.1.1(80), 1 packet

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R7:

R7# show logging | include %SYS-2-MALLOCFAIL

*Mar  1 00:05:10.123: %SYS-2-MALLOCFAIL: Memory allocation failed for size 1024, from process 0x12345678, pool Processor
*Mar  1 00:06:20.456: %SYS-2-MALLOCFAIL: Memory allocation failed for size 2048, from process 0x12345678, pool Processor
*Mar  1 00:07:30.789: %SYS-2-MALLOCFAIL: Memory allocation failed for size 512, from process 0x12345678, pool Processor

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R8:

R8# show logging | include %LDP-5-NBRCHG

*Mar  1 00:01:10.123: %LDP-5-NBRCHG: LDP Neighbor 10.0.0.2:0 (1) is UP
*Mar  1 00:02:20.456: %LDP-5-NBRCHG: LDP Neighbor 10.0.0.2:0 (1) is DOWN
*Mar  1 00:03:30.789: %LDP-5-NBRCHG: LDP Neighbor 10.0.0.2:0 (1) is UP
*Mar  1 00:04:40.012: %LDP-5-NBRCHG: LDP Neighbor 10.0.0.2:0 (1) is DOWN

Based on this output, what is the most likely problem?

A network engineer runs the following command on Router R9:

R9# show logging | include %DMVPN-5-ADJCHG

*Mar  1 00:01:05.123: %DMVPN-5-ADJCHG: NHRP: Peer 10.0.0.1 on Tunnel0 is UP
*Mar  1 00:02:10.456: %DMVPN-5-ADJCHG: NHRP: Peer 10.0.0.1 on Tunnel0 is DOWN
*Mar  1 00:03:15.789: %DMVPN-5-ADJCHG: NHRP: Peer 10.0.0.1 on Tunnel0 is UP
*Mar  1 00:04:20.012: %DMVPN-5-ADJCHG: NHRP: Peer 10.0.0.1 on Tunnel0 is DOWN

Based on this output, what is the most likely problem?

Examine the following partial router configuration:

logging buffered 16384
logging console warnings
logging monitor notifications
logging trap debugging
logging source-interface Loopback0
logging 192.168.1.100

What is the effect of this configuration?

Given the following partial configuration on a Cisco IOS-XE router:

logging host 10.1.1.1 transport tcp port 514
logging source-interface GigabitEthernet0/1
logging on

What is missing or incorrect in this configuration?

Refer to the following partial configuration:

logging console informational
logging monitor debugging
logging trap errors
logging buffered 4096

Which statement is true about the logging levels?

Consider the configuration snippet:

logging 192.168.1.10 vrf Mgmt-intf
logging source-interface Vlan1
logging trap 6

What is the effect of the 'logging trap 6' command?

Examine the following configuration:

logging host 10.1.1.1
logging host 10.1.1.2
logging host 10.1.1.3
logging origin-id hostname
logging facility local7

What is the purpose of the 'logging origin-id hostname' command?

Given the configuration:

logging buffered 8192 warnings
logging console alerts
logging monitor critical

Which of the following is true?