Courseiva

100-140 · domain

Networking and Network Connectivity

This domain covers how Cisco devices move traffic across LANs and VLANs: interface configuration modes, trunking with IEEE 802.1Q, inter-VLAN routing, and verification commands on Catalyst switches and routers. Questions are scenario-based, asking you to pick the correct CLI mode, command, or router function rather than recite theory.

40 questions7 easy24 medium9 hard

Focused practice

Practice Networking and Network Connectivity questions

Scored sessions drawing only from this domain — pick a length below.

Start 20-question practice test →

What this domain covers

What to know about Networking and Network Connectivity

Be able to move between Cisco IOS CLI modes, configure a router subinterface with 802.1Q encapsulation for inter-VLAN routing, and verify VLANs with show vlan. The key skill is choosing the correct configuration mode and matching subinterface encapsulation to the trunked VLAN.

Entering global configuration mode to make device configuration changes on Cisco IOS

Router-on-a-stick: one physical router interface with 802.1Q subinterfaces for inter-VLAN routing

Using show vlan to verify VLAN configuration, status, and switch port membership

Router functions: interconnecting networks, forwarding packets between subnets, and path selection

Watch out for

Common Networking and Network Connectivity exam traps

  • ▸Confusing privileged EXEC mode with global configuration mode; configuration changes require the configure terminal command, not just enable.
  • ▸Forgetting that router-on-a-stick needs 802.1Q encapsulation and unique subinterface IDs matching VLAN IDs on the trunk.
  • ▸Assuming show vlan displays routing or trunk details; it shows VLAN and port membership, while trunk status needs show interfaces trunk.

Question index

All Networking and Network Connectivity questions (40)

Click any question to see the full explanation, or start a practice session above.

1

A user at a small branch office reports that their laptop cannot reach any website, but the laptop can successfully ping 8.8.8.8. The technician runs ipconfig /all and sees the IPv4 address, subnet mask, and default gateway are correct, but the DNS server field is blank. Which action should the technician take first to restore web browsing?

Easy
2

A user on a corporate laptop can reach internal file shares by IP address but cannot reach them by hostname. The technician verifies the laptop has a valid IP address, subnet mask, and default gateway, and can ping the file server's IP address successfully. Which configuration should the technician verify next?

Easy
3

A user reports that they cannot access the internet, but they can ping the default gateway of their local subnet. What is the most likely cause of the issue?

Medium
4

Which protocol is primarily used to resolve a known IPv4 address to an unknown MAC address on a local area network?

Medium
5

A support technician is connecting a new Cat 6a patch cable from a wall jack to a user's desktop. The user reports intermittent disconnects and slow transfers. The technician notices the cable's RJ-45 connector has visible damage to the plastic tab that locks it into the port. Which layer of the OSI model is most directly implicated by this physical defect?

Hard
6

A network administrator needs to verify the connectivity between two hosts on the same VLAN. Which tool is most effective for testing if the host is reachable at the IP layer?

Medium
7

A technician is troubleshooting a workstation that cannot access network resources. The workstation is connected to a Cisco switch port that is configured for VLAN 10. The technician runs ipconfig and sees an IPv4 address of 169.254.10.5 with a subnet mask of 255.255.0.0. Which two statements describe the likely cause of this address? (Choose two.)

Medium
8

A small office is deploying a wireless network for employees and guests. The IT support technician must choose security settings that protect employee traffic while meeting these requirements: employee credentials must not be sent in cleartext over the air, and each employee must authenticate with unique credentials rather than a shared key. Which two wireless security configurations meet these requirements? (Choose two.)

Medium
9

Which TWO of the following are valid methods to secure a Cisco device's management access? (Choose two.)

Hard
10

Which protocol is used to resolve a known IPv4 address to a physical MAC address on a local Ethernet segment?

Medium
11

A technician is using the network scanner in a laptop's operating system to examine a colleague's workstation that is suspected of running an unauthorized service. The scan reports that TCP port 3389 on the workstation is open and accepting connections. Which service should the technician expect to be running on that port?

Medium
12

A technician is configuring a new Cisco switch for a small office. The office uses a single VLAN for all devices. The technician wants to assign an IP address to the switch's management interface so it can be accessed remotely via SSH. Which command must be entered in global configuration mode to create the management interface?

Medium
13

Refer to the exhibit. Router R1 lacks a default gateway and cannot reach external subnets. Which static route configuration correctly establishes a default route pointing to next-hop IP address 192.168.1.254?

Hard
14

A technician is asked to segment a network so that the finance department's traffic is isolated from the guest network at Layer 2. The requirement is that broadcast traffic from the guest network must not reach finance devices. Which technology should the technician implement to meet this requirement?

Hard
15

A user's desktop can reach devices on its own subnet but cannot reach any host on a remote network. The technician runs ipconfig and sees that the IPv4 address, subnet mask, and DNS server are all correct, but the default gateway field is blank. Which action should the technician take to resolve the problem?

Easy
16

A network technician is configuring a Cisco Catalyst switch for a small office. The company uses a single VLAN (VLAN 1) for all devices. The technician wants to allow remote management of the switch from a PC on the same subnet. Which IP configuration must be applied to the switch to enable this access?

Medium
17

A technician is configuring a Cisco IOS router that connects a small office to the internet. The ISP has assigned a single public IPv4 address on the WAN interface, and the router must allow the office's internal 192.168.10.0/24 hosts to access web servers on the internet. Which feature should the technician configure on the router to accomplish this?

Medium
18

An IT support technician needs to verify whether a remote server is actively listening on TCP port 443 before troubleshooting an HTTPS connectivity issue. Which command-line utility provides the most direct test of this specific TCP port state from a client machine?

Medium
19

Which layer of the OSI model is responsible for logical addressing and routing of packets between different networks?

Easy
20

A network administrator needs to connect two switches using a link that allows multiple VLANs to traverse the cable. Which configuration step is mandatory for this link?

Medium
21

A network administrator is configuring a Cisco wireless LAN controller (WLC) for a small office. The office has a single VLAN for both management and client traffic. The administrator wants to ensure that wireless clients receive IP addresses from the same subnet as the wired clients. Which interface type on the WLC should be configured to map to this VLAN?

Hard
22

Refer to the exhibit. A router is unable to reach any external networks. Based on the output, what is the most likely configuration error?

Hard
23

Which OSI layer is primarily responsible for end-to-end communication, flow control, and error correction of data segments?

Easy
24

A technician is troubleshooting a workstation that cannot reach any device beyond its own subnet. The workstation has a valid IP address, subnet mask, and DNS server. The technician suspects a Layer 2 or Layer 3 configuration issue. Which two items should the technician verify to confirm the workstation can communicate off-subnet? (Choose two.)

Medium
25

A network administrator troubleshoots a newly installed unmanaged gigabit switch connecting multiple workstations. Which TWO symptoms most strongly indicate a physical layer cabling issue rather than a higher-layer configuration problem? (Choose two)

Hard
26

What is the function of a default gateway in an IPv4 network?

Easy
27

A technician notices that a workstation connected to a Cisco switch port shows a link light but cannot reach any other device. The switch output shows the port in the err-disabled state with the reason psecure-violation. Which action should the technician take to restore connectivity while keeping the security feature active?

Hard
28

Which TWO of the following statements correctly describe the function of a default gateway in a local area network?

Medium
29

Which command-line interface (CLI) mode must a technician enter to perform configuration changes on a Cisco device?

Medium
30

Refer to the exhibit. An administrator is troubleshooting a link between two switches. The status shows 'up' but the protocol is 'down'. What is the most likely cause?

Medium
31

A network administrator configures inter-VLAN routing using a single physical router interface connected to an enterprise switch configured with IEEE 802.1Q trunking. What is the standard Cisco term for this specific routing architecture?

Medium
32

Which command is used to verify the current VLAN configuration, status, and port membership on a Cisco Catalyst switch?

Medium
33

Which THREE of the following are primary functions of a router in a modern enterprise network? (Choose three.)

Medium
34

Refer to the exhibit. A technician is troubleshooting connectivity for a device connected to FastEthernet0/2. Based on the output, what is the most likely cause of the issue?

Medium
35

A network administrator needs to connect a workstation to a switch port. The link must be configured to prevent loops while ensuring high availability. Which technology should be implemented on the switch port to immediately transition the port to the forwarding state upon connection?

Medium
36

A technician is connecting a new Cisco access point to a switch port in an office. The access point must receive its management IP address automatically from the DHCP server and must be placed in the wireless management VLAN. The switch port currently has no special configuration. Which switch port setting should the technician apply?

Medium
37

Refer to the exhibit. A technician notices that traffic cannot traverse GigabitEthernet0/1 on router R1. Based on the provided CLI output, what action must the technician perform to bring the interface operational?

Hard
38

When configuring a Cisco router interface, which THREE parameters are required for the interface to become 'up/up' and pass traffic? (Choose three.)

Medium
39

A user at a small branch office reports that file transfers to a server on a different subnet are extremely slow, even though the local network works fine. A technician runs the ipconfig /all command on the workstation and notices the DNS server address is 127.0.0.1. Which statement best describes the immediate problem with this configuration?

Easy
40

A technician is testing a newly installed fiber uplink between a distribution switch and an access switch. The link status shows up/up, and the technician wants to confirm the actual achievable throughput before putting the link into production. Which tool should the technician use to measure the real bandwidth between the two Cisco switches?

Medium

Frequently asked questions

What does the Networking and Network Connectivity domain cover on the 100-140 exam?
Be able to move between Cisco IOS CLI modes, configure a router subinterface with 802.1Q encapsulation for inter-VLAN routing, and verify VLANs with show vlan. The key skill is choosing the correct configuration mode and matching subinterface encapsulation to the trunked VLAN.
How many questions are in this domain?
This page lists all 40 Networking and Network Connectivity questions in the 100-140 question bank. The actual exam draws from this domain proportionally to its weighting in the official exam blueprint.
What is the best way to practise this domain?
Start with a short focused session (10 questions) to identify gaps, then work through explanations. Repeat with a longer session once the weak areas feel solid.
Can I practise only Networking and Network Connectivity questions?
Yes — the session launcher on this page filters questions to this domain only. Choose any session length for inline explanations and scoring.
Cisco Certified Support Technician - IT Support 100-140 Networking and Network Connectivity Practice Questions