100-140 Practice Question: Which protocol is primarily used to resolve a known IPv4 address to an unknown MAC…
Which protocol is primarily used to resolve a known IPv4 address to an unknown MAC address on a local area network?
⚠ Common exam trap
Students frequently confuse ARP with RARP, DNS, or DHCP, mistakenly thinking IP addresses are resolved from MAC addresses rather than the other way around.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
ARP
Address Resolution Protocol (ARP) is essential for local communication. Since Ethernet networks use MAC addresses to deliver frames to specific network interface cards, devices must map the target IP to a hardware address. Understanding ARP is vital for IT support, as it explains why devices cannot communicate if the resolution process fails, often due to misconfigured subnets or ARP table issues on the local gateway.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✗
DNS
Why it's wrong here
DNS translates names into IP addresses, for example www.cisco.com to an IPv4 or IPv6 address, one step earlier in the process. Once the destination IP address is known, the host still needs a MAC address to build the Ethernet frame, which DNS cannot provide. So a typical connection uses DNS to find the IP address, then ARP to find the next hop's MAC address.
- ✗
DHCP
Why it's wrong here
DHCP gives a host its own configuration, an IP address, subnet mask, default gateway and DNS servers, when it joins the network. It does not discover other devices' MAC addresses. After DHCP finishes, the host uses ARP whenever it needs the MAC address of a local destination or of its default gateway, for example before sending its first packet off the subnet.
- ✓
ARP
Why this is correct
ARP finds the MAC address that belongs to a known IPv4 address on the local network. The host broadcasts a request asking who has that address, the owner replies directly with its MAC address, and the host caches the answer for a few minutes. For remote destinations, it ARPs for the default gateway instead. IPv6 uses Neighbor Discovery over ICMPv6 for the same job.
- ✗
ICMP
Why it's wrong here
ICMP carries diagnostic and error messages, such as echo request and reply used by ping, destination unreachable and time exceeded used by traceroute. It does not map IP addresses to MAC addresses. In fact, before the first ping to a local host can be sent, the sender typically uses ARP to learn that host's MAC address, which is why the first ping sometimes times out.
Visual reference
Quick reference
Access Control Model Comparison
| Model | Acronym | Who Controls Access? | Best For |
|---|---|---|---|
| Discretionary Access Control | DAC | Resource owner | Small teams, file shares |
| Mandatory Access Control | MAC | System / security labels | Classified govt / military |
| Role-Based Access Control | RBAC | Administrator (via roles) | Enterprise environments |
| Attribute-Based Access Control | ABAC | Policy engine (user + resource attributes) | Fine-grained, dynamic policies |
| Rule-Based Access Control | RuBAC | System rules / ACLs | Firewall rules, network ACLs |
About these practice questions
One of 305 original 100-140 practice questions on Courseiva, each with a full explanation and wrong-answer analysis — not exam dumps or protected exam content. Learn why practice questions differ from exam dumps →
You might also like
Similar 100-140 questions
- A support technician is connecting a new Cat 6a patch cable from a wall jack to a user's desktop. The user reports inter…
- A network administrator needs to verify the connectivity between two hosts on the same VLAN. Which tool is most effectiv…
- A technician is troubleshooting a workstation that cannot access network resources. The workstation is connected to a Ci…
- A small office is deploying a wireless network for employees and guests. The IT support technician must choose security…
- Which TWO of the following are valid methods to secure a Cisco device's management access? (Choose two.)
Written and reviewed by Johnson Ajibi, MSc IT Security
Security Systems Architect · founder of Courseiva
Last reviewed September 2026 · checked against the official Cisco exam blueprint
This 100-140 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 100-140 exam.