LPIC-1 System Architecture — Timed 10 Questions

Question 1

Which command shows the amount of free and used memory in the system, including swap?

Accepted Answer

free -h. The `free -h` command displays the total, used, and free physical memory (RAM) and swap space in a human-readable format (e.g., GiB, MiB). The `-h` flag ensures output is scaled to appropriate units, making it the direct and correct tool for checking both memory and swap usage.

Answer

top

Answer

df -h

Answer

vmstat

Question 2

A system administrator needs to blacklist the kernel module 'pcspkr' to disable the PC speaker. Which is the correct method?

Accepted Answer

Add 'blacklist pcspkr' to /etc/modprobe.d/blacklist.conf. The 'blacklist' directive in a file under /etc/modprobe.d/ tells modprobe to ignore the specified module entirely, preventing it from being loaded automatically or manually. This is the standard method to permanently disable a kernel module like 'pcspkr' without removing its files.

Answer

Add 'load pcspkr' to /etc/modules

Answer

Add 'install pcspkr /bin/true' to /etc/modprobe.d/blacklist.conf

Answer

Remove the module from /lib/modules/$(uname -r)/kernel/drivers

Question 3

A system administrator notices that the server's clock is consistently off by several minutes. Which service should be used to synchronize the time with an external time source?

Accepted Answer

ntpd. The Network Time Protocol (NTP) daemon (ntpd) is the traditional and widely used service for synchronizing a server's clock with an external time source. It continuously adjusts the system time by communicating with NTP servers, compensating for clock drift and network delays to maintain accurate time. This makes ntpd the correct choice for resolving a consistent clock offset of several minutes.

Answer

timed

Answer

chronyd

Answer

systemd-timesyncd

Question 4

During boot, the kernel must mount the root filesystem. Which of the following is responsible for providing the kernel with the location of the root filesystem?

Accepted Answer

boot loader. The boot loader (e.g., GRUB) is responsible for loading the kernel into memory and passing it the location of the root filesystem via kernel command-line parameters such as `root=`. Without this parameter, the kernel would not know which block device or partition to mount as `/`. The boot loader reads configuration files (e.g., `grub.cfg`) that specify this parameter, making it the direct provider of the root filesystem location.

Answer

udev

Answer

initramfs

Answer

init

Question 5

A server has two disk drives: /dev/sda (SSD) and /dev/sdb (HDD). The administrator wants to place frequently accessed files on the SSD for performance. Which approach best achieves this using Linux filesystem features?

Accepted Answer

Create separate LVM logical volumes on each disk and mount them at different mount points.. LVM allows the administrator to create separate logical volumes on each physical disk (/dev/sda and /dev/sdb) and mount them at distinct mount points. By placing frequently accessed files on the SSD logical volume and less critical data on the HDD logical volume, the administrator can directly control which files benefit from the SSD's faster performance without mixing data or requiring complex overlays.

Answer

Configure RAID 0 across both disks to combine speed.

Answer

Use symbolic links to redirect file access to the SSD.

Answer

Use a union mount to overlay the SSD on top of the HDD.

Question 6

A technician is troubleshooting a system that fails to boot with the error 'Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)'. What is the most likely cause?

Accepted Answer

The kernel lacks the necessary driver for the storage controller.. The error 'VFS: Unable to mount root fs on unknown-block(0,0)' indicates that the kernel cannot locate or access the root filesystem. This typically occurs because the kernel lacks the necessary driver (module) for the storage controller (e.g., SATA, SCSI, NVMe) that the root device is connected to, so it cannot read the partition table or mount the root filesystem.

Answer

The init binary is missing or corrupted.

Answer

The root filesystem is corrupted and needs fsck.

Answer

The boot loader is not installed correctly.

Question 7

Which hardware component uses a unique address to identify itself on the network at the data link layer?

Accepted Answer

MAC address. The MAC address (Media Access Control) is a unique 48-bit identifier burned into the network interface controller (NIC) by the manufacturer. It operates at Layer 2 (data link layer) of the OSI model, enabling devices on the same local network segment to communicate directly using protocols like Ethernet or Wi-Fi.

Answer

IP address

Answer

Hostname

Answer

Port number

Question 8

A Linux system has two network interfaces: eth0 and eth1. The administrator wants to bond them for increased throughput. Which kernel module is required for bonding?

Accepted Answer

bonding. The bonding driver in Linux allows multiple network interfaces to be aggregated into a single logical interface for increased throughput or redundancy. The correct kernel module is named 'bonding' (loaded via modprobe bonding or compiled into the kernel), which implements the IEEE 802.3ad Link Aggregation standard and other bonding modes. Option B is correct because 'bonding' is the exact module name used in the Linux kernel.

Answer

aggregation

Answer

team

Answer

bond

Question 9

An administrator needs to ensure that a specific kernel module is loaded automatically at boot. Which file should be used to permanently load the module?

Accepted Answer

/etc/modules. On modern Linux systems using a standard init system, the file /etc/modules (or /etc/modules-load.d/*.conf on systemd-based distributions) is read at boot to load specified kernel modules automatically. This file lists module names one per line, and the kernel's module loading mechanism processes it early in the boot sequence to ensure the module is available before services that depend on it start.

Answer

/etc/modprobe.d/modules.conf

Answer

/etc/sysconfig/modules

Answer

/etc/conf.modules

Question 10

Which command displays information about the CPU, including model name, cache size, and flags?

Accepted Answer

lscpu. The `lscpu` command is the correct choice because it is specifically designed to display CPU architecture information, including model name, cache sizes, and flags (such as SSE, AES, etc.), by reading data from sysfs and /proc/cpuinfo in a human-readable format. It provides a concise summary without requiring root privileges, making it the most appropriate tool for this task.

Answer

uname -a

Answer

cat /proc/cpuinfo

Answer

dmidecode