Courseiva

Cisco Certified Support Technician - IT Support (100-140) — Questions 151–225

305 questions total · 5 pages · All types, answers revealed

Page 2

Page 3 of 5

Page 4
151
MCQhard

A technician notices that a workstation connected to a Cisco switch port shows a link light but cannot reach any other device. The switch output shows the port in the err-disabled state with the reason psecure-violation. Which action should the technician take to restore connectivity while keeping the security feature active?

A.Enable errdisable recovery with an interval so the port re-enables automatically.
B.Remove the port security configuration from the interface and re-enable the port.
C.Shut down and re-enable the interface after removing the offending MAC address or device.
D.Configure the interface as a trunk port so the violation no longer applies.
AnswerC

A psecure-violation err-disabled state occurs when an unauthorized MAC address appears on a port with port security enabled. Removing the offending device or clearing the learned address and then cycling the interface with shutdown and no shutdown restores service while port security remains configured and enforced. This satisfies both restoring connectivity and keeping the security feature active.

Why this answer

The err-disabled reason psecure-violation means port security detected a MAC address beyond the allowed maximum or an address not in the secure table. The correct recovery is to eliminate the offending device or address and then re-enable the interface with shutdown followed by no shutdown. This clears the violation while leaving port security configured, so the protection remains in force for future unauthorized connections.

Exam trap

The trap here is reaching for errdisable recovery or removing security instead of correcting the violation cause.

152
Multi-Selectmedium

Which TWO of the following statements correctly describe the function of a default gateway in a local area network?

Select 2 answers
A.It is the IP address of the local switch used for internal VLAN communication.
B.It allows devices to communicate with hosts on different subnets.
C.It provides the IP address for all devices within the same broadcast domain.
D.It acts as the exit point for traffic destined for remote networks.
E.It is responsible for translating private IP addresses to public ones.
AnswersB, D

When a host determines that a destination IP address is outside its own subnet, it encapsulates the frame with the MAC address of the default gateway. This enables the router to receive the packet and forward it toward the correct network destination across the internetwork.

Why this answer

A default gateway is a crucial component that enables devices to communicate outside of their local subnet. It serves as the path for traffic destined for remote networks by forwarding packets to a router. Understanding the role of the gateway is fundamental for network support, as misconfiguration is one of the most common reasons for end-user connectivity issues when accessing external resources or the internet.

Exam trap

Candidates often assume the default gateway handles local traffic between devices on the same subnet, forgetting that local communication happens entirely via Layer 2 MAC addresses.

153
MCQeasy

Which macOS feature allows a user to securely wipe a drive and reset the device to factory settings without reinstalling the OS from external media?

A.Disk Utility Erase function
B.Erase All Content and Settings
C.Target Disk Mode
D.Time Machine Restore
AnswerB

This feature provides a streamlined way to securely delete all user data and reset system settings without the need for a full OS reinstallation. It is the fastest and most secure method for preparing a macOS device for a new user, ensuring all personal data is permanently wiped.

Why this answer

The 'Erase All Content and Settings' feature is designed to perform a secure wipe of user data while keeping the system software intact. This is the modern, preferred method for repurposing or returning devices in an enterprise environment. It leverages the underlying APFS encryption keys to cryptographically erase data, ensuring that no sensitive remnants are recoverable, which is vital for data privacy compliance.

Exam trap

Candidates often suggest 'Disk Utility' or 'Recovery Mode'. While those work, they are legacy methods; 'Erase All Content and Settings' is the specific modern feature for this task.

154
Multi-Selecthard

A user reports that a browser warning appeared while visiting a supplier portal, and later that day several files on a shared drive were renamed with a strange extension. As the IT support technician, which two initial actions best support containment and later investigation? (Choose two.)

Select 2 answers
A.Preserve the current system state and collect volatile evidence such as running processes, network connections, and logged-on users before any cleanup.
B.Disconnect the affected workstation from the wired and wireless networks.
C.Run a full antivirus scan and delete every file it flags as malicious.
D.Email the suspicious browser warning details to all staff so they can watch for similar messages.
E.Immediately reimage the workstation to guarantee that no malware remains.
AnswersA, B

Volatile data disappears when the machine is powered off or rebooted, so capturing running processes, active network connections, and logged-on users immediately supports root-cause analysis and scope determination. This evidence can identify the initial vector, the malware family, and whether other hosts were contacted, which guides the broader response.

Why this answer

Containment and investigation both depend on limiting the spread while keeping evidence intact. Disconnecting the workstation stops outbound communication and lateral movement, and capturing volatile data before any cleanup preserves the processes, connections, and user context that explain what happened. Together these actions support scope determination and a safe recovery later.

Exam trap

The trap here is treating immediate eradication, such as reimaging or deleting flagged files, as the first step instead of containing the host and preserving volatile evidence.

155
MCQhard

Which THREE factors should be considered when designing a remote access VPN solution for a global workforce? (Choose three)

A.Authentication and multi-factor security
B.Geographic proximity of VPN concentrators
C.Compatibility with local hardware manufacturers
D.Bandwidth and latency impact on applications
E.Mandatory use of wired connections for all users
AnswerA, B, D

Multi-factor authentication (MFA) is a critical security requirement for any remote access solution. Given that VPN credentials are often targeted by attackers, ensuring that an additional layer of verification exists prevents unauthorized access, even if a primary password is compromised, which is essential for protecting sensitive corporate infrastructure.

Why this answer

Designing a global remote access VPN requires balancing performance, security, and scalability. Users may be connecting from various regions with different ISP qualities, making optimized routing and authentication essential. By considering latency, authentication methods, and split-tunneling policies, architects can ensure a seamless user experience while maintaining the corporate security posture.

These factors are vital for supporting diverse workforces and ensuring that productivity is not hindered by remote connectivity limitations or security gaps.

Exam trap

Test-takers often focus solely on encryption protocols while ignoring logistical and performance factors like geographic latency and user bandwidth.

156
MCQhard

A technician suspects a workstation is infected with malware that is contacting a command-and-control server. The technician wants to capture the actual traffic leaving the host for later analysis without disrupting the user's work. Which action best accomplishes this?

A.Run a full antivirus scan on the workstation.
B.Change the workstation's DNS server to a public resolver.
C.Enable a port mirror on the switch port and capture with a protocol analyzer.
D.Disable the switch port the workstation is connected to.
AnswerC

A switched port analyzer session copies the workstation's traffic to a monitoring port where a protocol analyzer can record it. This captures the real outbound packets, including any command-and-control communication, without interrupting the user's session. It directly satisfies the requirement to gather evidence while the host continues operating normally.

Why this answer

Copying the workstation's traffic to a monitoring port with a SPAN session lets a protocol analyzer record the actual outbound packets, including command-and-control exchanges, while the user keeps working. This yields the evidence needed for analysis without containment actions that would halt the infection's observable behavior or interrupt the user's productivity.

Exam trap

The trap here is reaching for immediate containment by disabling the port, when the scenario explicitly requires capturing live traffic without disrupting the user.

157
MCQmedium

When upgrading a modular switch, which hardware factor is most important to consider to prevent a chassis power oversubscription?

A.The total number of available chassis slots.
B.The wattage capacity of the power supply units vs. module draw.
C.The speed of the system bus on the supervisor engine.
D.The amount of memory installed on the supervisor.
AnswerB

Each line card consumes a specific amount of power. The total power draw of all cards, supervisors, and fans must remain within the maximum capacity of the installed PSUs. Oversubscribing results in automatic load shedding or failure to power on new components, potentially causing critical infrastructure service interruptions.

Why this answer

Power budget management is critical in modular chassis systems. Adding line cards or power-consuming modules without sufficient power supply capacity leads to system instability or module failure. Understanding the power budget allows technicians to plan hardware upgrades accurately, ensuring that the total draw does not exceed the capacity of the installed power supply units (PSUs) while maintaining redundancy during operation.

Exam trap

Candidates often focus solely on physical slot availability or port density, forgetting to calculate total wattage draw against power supply capacity.

158
MCQmedium

A network administrator is configuring a Cisco switch and wants to mitigate VLAN hopping attacks. The administrator has already set the native VLAN to an unused VLAN on all trunk ports. Which additional configuration should be applied to trunk ports to further prevent VLAN hopping?

A.Configure all trunk ports with the 'switchport nonegotiate' command.
B.Enable VTP pruning on all trunk ports.
C.Assign all unused ports to the native VLAN.
D.Enable Dynamic Trunking Protocol (DTP) on all access ports.
AnswerA

The 'switchport nonegotiate' command disables DTP on a trunk port, preventing the port from negotiating trunking with neighboring devices. This helps mitigate VLAN hopping attacks because an attacker cannot trick the switch into forming a trunk. When combined with changing the native VLAN, it significantly reduces the attack surface for VLAN hopping. This is a recommended best practice for trunk ports that should always be trunks.

Why this answer

To further prevent VLAN hopping after changing the native VLAN, the administrator should disable DTP on trunk ports using the 'switchport nonegotiate' command. This prevents an attacker from negotiating a trunk link and exploiting VLAN hopping techniques. Disabling DTP on access ports and avoiding assigning unused ports to the native VLAN are also recommended, but the specific additional step for trunk ports is 'switchport nonegotiate'.

Exam trap

The trap here is confusing VTP pruning with security measures or thinking that enabling DTP enhances security, when in fact disabling DTP is the correct action.

159
MCQmedium

What is the primary function of the 'secret' password in the 'enable secret' configuration command on Cisco devices?

A.It enables encryption for all data packets passing through the router.
B.It forces all local console users to use two-factor authentication.
C.It stores the password in a hashed format in the configuration.
D.It automatically updates the device IOS to the latest version.
AnswerC

'enable secret' stores the privileged EXEC password as a one-way hash rather than plain text, so anyone viewing the configuration or a backup cannot read the password directly. Older devices use MD5 (type 5); newer IOS releases support stronger algorithms, type 8 (PBKDF2-SHA256) and type 9 (scrypt), chosen with 'enable algorithm-type'. It also overrides the older 'enable password', which is stored in clear text or weakly scrambled type 7.

Why this answer

The 'enable secret' command provides a stronger level of security than the 'enable password' command because it uses an MD5 or SHA-based hash to store the password. This prevents the password from being visible in plain text within the device's running-config or startup-config files. Using the 'secret' command is a fundamental security requirement for protecting administrative privilege levels against unauthorized access via configuration file theft or unauthorized viewing.

Exam trap

Candidates often confuse 'enable secret' with 'enable password', incorrectly believing that both store passwords in plain text or that 'secret' merely enables password prompting rather than applying cryptographic hashing.

160
MCQeasy

Which keyboard shortcut is used to open the 'Force Quit' applications dialog on a macOS system?

A.Command + Option + Escape
B.Control + Alt + Delete
C.Command + Shift + Q
D.Option + Command + P + R
AnswerA

This specific combination is the standard macOS keyboard shortcut for invoking the Force Quit Applications dialog. It is a critical, universally supported keyboard sequence that provides a safe and reliable way for users to end unresponsive processes without risking data integrity or the stability of other apps.

Why this answer

Knowing the Force Quit shortcut is fundamental for any IT technician supporting macOS users. It provides a quick way to terminate unresponsive applications without needing to restart the entire system. This skill ensures that technicians can resolve common application hangs quickly, minimizing user downtime and providing a seamless experience for end-users who may not be familiar with command-line alternatives like 'killall'.

Exam trap

Test-takers frequently confuse the Force Quit shortcut with Windows combinations like Ctrl+Alt+Del or confuse macOS modifier keys like Option and Command.

161
MCQhard

You are configuring a Windows 10 Pro workstation for a remote user. You need to ensure that the user can access network shares while maintaining security. Which TWO of the following tasks should you perform to adhere to standard security best practices?

A.Enable Everyone access on all shares
B.Disable Network Discovery for public profiles
C.Configure NTFS permissions for specific users
D.Use HomeGroup for network connectivity
E.Disable the Windows Firewall
AnswerB, C

Disabling Network Discovery on public network profiles is a critical security step that prevents the workstation from being visible to other devices on potentially untrusted networks. This minimizes the attack surface by ensuring the machine does not advertise its services or files to unauthorized parties.

Why this answer

Configuring network discovery and user-level permissions is critical for secure file sharing. Disabling Network Discovery prevents unauthorized devices from seeing the machine, while NTFS permissions provide granular control over file access compared to share permissions alone. These steps ensure that only authorized users can access the data, which is a fundamental requirement for securing Windows environments in a professional network setting.

Exam trap

Candidates often suggest disabling sharing or public profiles entirely. However, the question asks for security best practices that still allow for necessary network functionality in a business environment.

162
MCQmedium

Which Cisco security feature should be used to protect the control plane of a network device from excessive traffic?

A.VLAN Trunking Protocol
B.Control Plane Policing (CoPP)
C.Spanning Tree Protocol
D.Network Address Translation (NAT)
AnswerB

CoPP allows administrators to implement policies that regulate the amount of traffic sent to the device CPU. It protects the router's control plane from being overwhelmed by excessive packets, ensuring that critical processes like routing protocols and management sessions remain active even during high traffic loads.

Why this answer

Control Plane Policing (CoPP) is a vital feature that allows administrators to define policies to rate-limit or drop traffic destined for the device's CPU. By protecting the control plane, CoPP ensures that legitimate management and routing traffic can still be processed even during a DoS attack or high traffic volume, maintaining the stability and availability of the network device itself under adverse conditions, which is crucial for infrastructure resilience.

Exam trap

Candidates often select generic access control lists (ACLs) applied to physical interfaces instead of Control Plane Policing, missing the specific tool designed to protect the router's CPU.

163
MCQhard

Which protocol is most secure for providing authentication and integrity for network management traffic?

A.SNMPv1
B.SNMPv2c
C.SNMPv3
D.Telnet
AnswerC

SNMPv3 is the modern, secure version of the protocol. It supports user-based authentication and message encryption, protecting against both eavesdropping and unauthorized access to managed devices. It is the industry standard for securely managing network infrastructure via centralized monitoring platforms.

Why this answer

SNMPv3 is the only version of the Simple Network Management Protocol that provides robust security features, including authentication and encryption. Older versions (v1 and v2c) transmit community strings in cleartext, making them highly insecure. By utilizing SNMPv3, administrators ensure that management data, which could contain sensitive configuration details, is protected from sniffing and tampering, which is a critical requirement for maintaining a secure and trustworthy network infrastructure.

Exam trap

Candidates often select SNMPv2c because it is common. They fail to recognize that v2c uses cleartext community strings, which are inherently insecure for modern enterprise network management.

164
MCQhard

Several users in a single branch office report they cannot access the internet, but they can still access local files on the branch server. What should the technician's next troubleshooting step be to isolate the problem?

A.Reinstall the operating system on all affected workstations.
B.Replace the local branch server's network interface card.
C.Ping the default gateway and an external IP address like 8.8.8.8.
D.Check the power status of the local network switches.
AnswerC

Pinging the default gateway verifies local connectivity to the router, while pinging an external IP helps determine if the issue is with the Internet Service Provider or with DNS resolution. This step helps the technician quickly narrow the problem down to the router, the WAN link, or an external service provider failure.

Why this answer

Isolating a problem involves determining the boundary between what is working and what is not. Since local resources are accessible, the internal switch and the workstations' IP configurations are likely functional. The issue likely lies at the gateway, the ISP connection, or the DNS settings, and the next step should focus on testing connectivity beyond the local subnet.

Exam trap

Candidates often attempt to troubleshoot the local server or individual workstations, wasting time on local issues when the problem is clearly limited to external connectivity beyond the branch gateway.

165
MCQmedium

A technician observes that a system service is stuck in a 'Starting' state and refuses to accept new commands. Which command-line tool, combined with the PID, allows for the immediate termination of the service process?

A.sc stop
B.taskkill /f /pid
C.net stop
D.shutdown /r /f
AnswerB

The /f flag forces the immediate termination of the process, and the /pid flag allows the technician to specify the exact process ID to stop. This is the most effective way to kill a hung service process that is not responding to standard Service Control Manager service stop commands.

Why this answer

The 'taskkill' command is the standard utility for forcing the termination of a process. By providing the Process ID (PID) discovered via 'tasklist', a technician can forcefully end a hung process that is unresponsive to normal service stop commands. This is a common requirement when a background service process locks up and prevents system or application operations.

Exam trap

Candidates often choose 'tasklist' instead of 'taskkill', confusing the tool used to identify the process with the tool required to actually terminate the hung service or application.

166
MCQeasy

A small office wants to protect its wireless network from unauthorized users. The office currently uses WPA2-Personal with a pre-shared key that is written on a whiteboard in the break room. Which change should the technician make to improve security?

A.Reduce the wireless transmit power so the signal does not leave the building.
B.Disable SSID broadcasting so the network name is hidden.
C.Enable MAC address filtering to allow only known devices.
D.Change the pre-shared key to a strong passphrase and remove it from public view.
AnswerD

The pre-shared key is currently exposed on a whiteboard, allowing anyone who sees it to join the wireless network. Changing it to a strong, unique passphrase and keeping it confidential prevents unauthorized access. This directly addresses the security weakness without changing the wireless standard or requiring new hardware.

Why this answer

The exposed pre-shared key on a whiteboard allows anyone who sees it to join the wireless network. Changing it to a strong passphrase and removing it from public view directly closes that vulnerability. Other measures such as hiding the SSID or filtering MAC addresses do not address the leaked key and are easily bypassed.

Exam trap

The trap here is believing that hiding the SSID or filtering MAC addresses is sufficient when the pre-shared key is publicly visible.

167
MCQmedium

A user is unable to map a network drive via SMB on macOS. You suspect the issue is related to the protocol version negotiation. What is the most effective way to troubleshoot this?

A.Use the ping command to verify connectivity to the server.
B.Run smbutil statshares -a in the Terminal.
C.Reset the user's keychain entries for the server.
D.Clear the DNS cache using dscacheutil.
AnswerB

This command provides a detailed report of all currently mounted SMB shares, showing the protocol version and encryption status. If a share fails to mount, it helps the technician pinpoint whether the server is rejecting the connection based on protocol versioning or other SMB-specific configuration requirements.

Why this answer

The 'smbutil' command is the definitive tool for diagnosing SMB connectivity. By using 'smbutil statshares -a', a technician can view the current negotiation status, including the version (e.g., SMB 2.1, 3.0) and encryption settings. This helps identify if the server is forcing an outdated, insecure protocol or if there is a mismatch between the client's supported features and the server's requirements.

Exam trap

Candidates often try to troubleshoot the server itself first or use generic network tools like 'ping'. They fail to check the specific SMB protocol negotiation between client and server.

168
MCQmedium

A user at your company reports that their MacBook Air shuts down unexpectedly when unplugged, even though macOS shows 45% battery remaining. You need to determine if the battery needs replacement. Which command-line utility should you use to retrieve the battery's cycle count and condition?

A.pmset -g log
B.ioreg -l | grep Battery
C.sysctl hw.battery
D.system_profiler SPPowerDataType
AnswerD

This command outputs detailed power and battery information, including cycle count, condition, and charge status. It directly addresses the need to assess battery health without a GUI. The other commands do not provide battery-specific data. For a MacBook Air with unexpected shutdowns, cycle count and condition are key indicators of whether the battery has degraded beyond service thresholds.

Why this answer

The system_profiler SPPowerDataType command provides comprehensive battery details, including cycle count and condition, which are critical for determining if a battery needs replacement. In this scenario, the MacBook Air shuts down unexpectedly despite showing 45% charge, indicating possible battery degradation. Checking cycle count and condition helps the technician decide whether to replace the battery or investigate other causes.

Exam trap

The trap here is assuming that pmset or ioreg can easily provide battery cycle count, but they are not designed for that purpose and require additional parsing.

169
Multi-Selecthard

Which THREE objectives are primary goals of the Incident Management process in a help desk environment? (Choose three.)

Select 3 answers
A.Restore normal service operation as quickly as possible.
B.Identify and eliminate the root cause of recurring failures.
C.Minimize the adverse impact on business operations.
D.Maintain service quality as defined in the Service Level Agreement.
E.Perform a cost-benefit analysis for new infrastructure hardware.
AnswersA, C, D

The primary mission of incident management is to get the user back to work by resolving the immediate disruption to their service. Speed and efficiency are prioritized to ensure that business productivity is not hindered by technical failures, often involving the use of standard workarounds or temporary fixes to bypass the issue.

Why this answer

Incident Management focuses on the rapid restoration of service and the minimization of negative impacts on business operations. Unlike Problem Management, which seeks to identify the underlying root cause of recurring issues, Incident Management is focused on operational continuity and meeting the immediate needs of the users as defined in the Service Level Agreements.

Exam trap

Students often confuse Incident Management goals with Problem Management goals, incorrectly selecting root cause analysis as a primary objective.

170
MCQeasy

A user receives a phone call from someone claiming to be from the IT help desk. The caller says a critical update must be installed right now and asks the user to read out the six-digit code that just appeared on their phone. Which action should the user take?

A.Hang up and verify the request through the organization's official help desk number before taking any action.
B.Read the code to the caller so the update can proceed quickly.
C.Ask the caller to email the request from an official company address, then read the code.
D.Provide only the first three digits of the code to confirm the caller is legitimate.
AnswerA

Ending the call and independently contacting the known help desk number defeats caller ID spoofing and confirms whether the request is genuine. This is the correct response because it refuses to disclose the code while still allowing a legitimate issue to be handled through a trusted channel. Verification through an official number is the key step.

Why this answer

The caller is using vishing to obtain a multi-factor authentication code, which would let them complete a login as the user. The safe response is to end the call and verify the request by contacting the organization's official help desk number. Legitimate support staff never ask for one-time codes, so refusal plus independent verification protects the account.

Exam trap

The trap here is believing that partial disclosure or an email confirmation makes sharing a one-time code safe, when any disclosure of the code enables account takeover.

171
Multi-Selectmedium

A technician is preparing to install a new Cisco Catalyst 9200 switch in a rack. Which two hardware components must be verified as present and compatible before powering on the switch? (Choose two.)

Select 2 answers
A.Fan tray with the correct airflow direction
B.Power supply units rated for the switch model
C.Console cable with a DB-9 connector
D.SFP+ transceiver for uplink connectivity
E.Rack-mount brackets and screws
AnswersA, B

The fan tray must match the intended airflow direction (front-to-back or back-to-front) to ensure proper cooling. Installing a fan tray with the wrong airflow can cause overheating and thermal shutdowns. Verifying airflow direction is essential before powering on the switch in a rack.

Why this answer

Before powering on a Catalyst 9200, the technician must ensure the power supplies are compatible and the fan tray provides the correct airflow direction. These components are critical for safe operation and cooling. Console cables, SFP+ transceivers, and rack-mount brackets are either optional or unrelated to the power-on prerequisites.

Exam trap

The trap here is including optional or management-related hardware like console cables or transceivers as prerequisites for powering on the switch.

172
MCQmedium

Which component of a Cisco switch is responsible for providing persistent storage for the startup configuration file, ensuring it remains available after a power cycle?

A.RAM
B.NVRAM
C.Flash Memory
D.ROM
AnswerB

NVRAM is specifically designed to retain data even when the device loses power. It is the designated location for the startup configuration file, ensuring that the switch loads the desired operational parameters automatically every time it initializes during the boot process after a power outage or reload.

Why this answer

Understanding memory types is crucial for switch management. NVRAM (Non-Volatile Random Access Memory) serves as the persistent storage for the startup configuration. Differentiating between memory types like RAM, Flash, and NVRAM helps technicians understand where files are stored, how configurations are loaded during boot, and why certain administrative actions, such as saving the configuration, are necessary to prevent data loss after a reboot.

Exam trap

Candidates often confuse the startup configuration storage (NVRAM) with the running configuration storage (RAM). They incorrectly assume the startup config is loaded directly from Flash or RAM during normal operation.

173
Multi-Selecthard

A technician is troubleshooting a Windows 10 workstation that fails to apply a new Group Policy setting. The technician runs 'gpupdate /force' and receives the error 'Computer policy could not be updated successfully. The following errors were encountered: The processing of Group Policy failed. Windows could not resolve the computer name.' Which TWO actions should the technician take to resolve this issue? (Choose two.)

Select 2 answers
A.Run 'ipconfig /flushdns' and 'ipconfig /registerdns' to refresh DNS records.
B.Restart the 'Group Policy Client' service on the workstation.
C.Verify that the computer account exists in Active Directory and is enabled.
D.Check the time and date settings on the workstation and ensure they are synchronized with the domain controller.
E.Rejoin the workstation to the domain using the same computer name.
AnswersA, C

The error can also be caused by stale or incorrect DNS records for the computer. Flushing the DNS resolver cache and re-registering the computer's DNS records ensures that the computer's hostname resolves correctly to its IP address, allowing Group Policy processing to succeed.

Why this answer

The error 'Windows could not resolve the computer name' typically stems from Active Directory or DNS problems. The computer account must exist and be enabled in Active Directory for authentication and Group Policy retrieval. Additionally, DNS records must be correct so the computer can locate the domain controller.

Flushing and re-registering DNS ensures proper name resolution. Other actions like restarting services or checking time are less directly related.

Exam trap

The trap here is focusing on the Group Policy service or time sync, while the error explicitly points to name resolution, which requires checking Active Directory and DNS.

174
Multi-Selecthard

An IT support technician is preparing a knowledge base article for first-level agents who will triage tickets about printers that will not print for multiple users on the same floor. Which TWO initial diagnostic steps should the article recommend before dispatching a technician? (Choose two.)

Select 2 answers
A.Replace the toner cartridge in the printer, since low toner can cause jobs to stop printing.
B.Reinstall the printer driver on every affected user's workstation to rule out corrupted drivers.
C.Verify that the print server's spooler service is running and that the queue is not paused or holding stuck jobs.
D.Escalate directly to the printer vendor's support line and open a hardware case for the device.
E.Confirm the affected users are on the same subnet and can reach the printer by its IP address or hostname.
AnswersC, E

When several users on one floor cannot print, a shared infrastructure component such as the print server or its queue is a prime suspect. Checking that the spooler service is running and that the queue is not paused or jammed with a stuck job can resolve the outage without a site visit. It is a fast, remote check that directly matches the multi-user symptom pattern.

Why this answer

A printing outage affecting several users on one floor usually stems from shared components rather than individual PCs. Checking the print server's spooler and queue state, and confirming the users can reach the printer over the network, are quick remote steps that either resolve the issue or clearly direct the escalation. Per-workstation driver work and hardware actions come only after shared infrastructure is cleared.

Exam trap

The trap here is treating a floor-wide print failure as many separate workstation problems, when the shared print server and network path should be checked first.

175
MCQmedium

An organization has a Service Level Agreement (SLA) that requires 'Critical' tickets to be resolved within 4 hours. A technician receives a ticket for a single printer failure in a department with five other working printers. How should the technician categorize this ticket?

A.Categorize as Critical because any hardware failure is a high priority.
B.Categorize as Low or Medium because there is no immediate work stoppage.
C.Categorize as High to ensure the user is impressed with IT response times.
D.Categorize as Urgent because the user is a department manager.
AnswerB

The availability of five other functional printers means the business process can continue with minimal disruption, justifying a lower priority level. This allows the help desk to allocate resources to more pressing issues while still acknowledging that the printer requires eventual repair or replacement according to standard operating procedures.

Why this answer

Proper ticket categorization and prioritization are essential for meeting SLA requirements and managing technician workloads effectively. Priority is typically determined by assessing both the urgency and the business impact of the reported issue. Since redundant resources are available, the impact is localized and minimal, allowing the technician to prioritize more severe system-wide outages ahead of this request.

Exam trap

Candidates tend to panic and over-prioritize any hardware failure as 'Critical' without evaluating overall business impact and redundancy.

176
MCQeasy

When managing macOS updates, which tool allows an administrator to defer OS updates for a specific period, which is common in managed enterprise environments?

A.System Settings > General > Software Update
B.Apple Configurator
C.MDM Configuration Profile
D.Terminal softwareupdate command
AnswerC

MDM profiles enable centralized control over macOS update behavior. By configuring the Software Update payload, administrators can specify deferral periods for major, minor, and security updates, ensuring that the organization remains compliant and stable while testing software updates in a controlled, non-production environment first.

Why this answer

Mobile Device Management (MDM) solutions are the standard for enterprise macOS administration. MDM profiles allow administrators to restrict update availability, enforce software versioning, and defer major OS upgrades. This is critical for ensuring application compatibility and testing new macOS versions before deployment, maintaining stability across a fleet of company-owned laptops and workstations.

Exam trap

Candidates often assume macOS updates are managed via the local System Settings or App Store. In enterprise environments, these local settings are typically superseded by MDM configuration profiles.

177
MCQhard

Refer to the exhibit. A user is reporting intermittent connectivity and slow speeds on a desktop connected to this switch port. Based on the output, what should the technician investigate as the most likely problem?

A.The Ethernet cable is longer than the 100-meter limit.
B.There is a duplex mismatch between the switch and the workstation.
C.The switch port is failing and needs to be physically replaced.
D.The workstation is sending too much broadcast traffic.
AnswerB

Collisions on a full-duplex interface almost always point to a duplex mismatch. If the switch is forced to full-duplex but the workstation is set to half-duplex (or vice versa), the half-duplex side will detect a collision whenever it tries to transmit while receiving data, leading to the errors seen in the exhibit.

Why this answer

In a modern Ethernet environment, collisions should not occur on a link configured for full-duplex. When they do, it is a strong indicator of a duplex mismatch, where one side of the link is set to full-duplex and the other is set to half-duplex. This causes significant performance degradation and errors as the two devices struggle to communicate effectively.

Exam trap

Test-takers often misinterpret collision counters on modern switched networks as cable length issues rather than recognizing a duplex mismatch.

178
MCQhard

Refer to the exhibit. What will occur if a third device with a different MAC address is plugged into Gi0/1?

A.The third device will be ignored, but the port will remain active.
B.The third device's MAC address will replace the first one.
C.The port will be placed into an error-disabled state.
D.The third device will be allowed to communicate.
AnswerC

Because the maximum number of MAC addresses is set to 2 and no specific violation mode was configured, the switch defaults to 'shutdown'. A third device causes a security violation, triggering the port to transition to an error-disabled state, thereby protecting the network from unauthorized access.

Why this answer

With the 'sticky' keyword, the switch learns the first two MAC addresses it sees and adds them to the running configuration. Once the maximum of 2 is reached, any additional MAC address encountered on the port will trigger the default violation mode. By default, this mode is 'shutdown', which disables the port to protect the network from unauthorized hardware, necessitating manual administrator intervention to resolve the security violation.

Exam trap

Candidates often assume the violation mode is 'protect' or 'restrict' without checking the default behavior. They forget that the default violation mode for port security is 'shutdown'.

179
MCQmedium

A macOS user is experiencing high CPU utilization caused by a background process. Which Terminal command should be used to identify the process ID (PID) and terminate the process gracefully?

A.ps aux | grep processname; sudo kill -9 PID
B.top; sudo kill PID
C.netstat -an; sudo kill PID
D.df -h; sudo killall PID
AnswerB

The 'top' command allows the technician to observe the system and locate the PID of the offending process. Sending a standard 'kill' signal (SIGTERM) allows the process to perform necessary cleanup tasks before exiting, which is the standard, safest practice for managing system resources on macOS.

Why this answer

The 'top' command provides a real-time view of system processes, allowing the technician to identify the PID of a runaway process. Once the PID is identified, the 'kill' command sends a termination signal. Using 'kill' (SIGTERM) is preferred over 'kill -9' (SIGKILL) because it allows the application to save state and exit gracefully, preventing potential data corruption in open documents.

Exam trap

Candidates often choose 'kill -9' as the default termination method. While effective, it is not 'graceful' and ignores cleanup routines, potentially causing data corruption or leaving behind orphaned temporary files.

180
MCQeasy

Which type of cable should a technician use to connect a workstation to the console port of a Cisco switch for initial configuration?

A.Standard Cat6 straight-through Ethernet cable.
B.Rollover cable.
C.Crossover Ethernet cable.
D.USB-C cable.
AnswerB

A rollover cable, often light blue in color, is specifically wired for Cisco console ports. The pinout is reversed on one end, allowing the serial interface of the switch to communicate correctly with the terminal device. This is the mandatory cable type for all manual Cisco hardware management tasks.

Why this answer

Correct cabling is the first step in successful device management. The rollover cable is a specific standard required for Cisco console access. Recognizing the difference between a standard Ethernet patch cable and a rollover cable prevents frustration during setup and ensures that the terminal emulation software can establish a proper physical connection to the switch's command-line interface without signal errors or data corruption.

Exam trap

Candidates often choose standard Ethernet patch cables because they are common, failing to recognize that console ports require the specific pinout of a rollover cable to function correctly.

181
MCQeasy

A user calls the help desk and states that their Windows workstation has a black screen but they can hear the Windows startup sound. The power LED on the monitor is amber. What should the technician check FIRST?

A.The RAM modules inside the workstation
B.The power supply wattage rating
C.The monitor's input source selection and video cable connection
D.The hard drive's S.M.A.R.T. status
AnswerC

An amber power LED on the monitor indicates the display is receiving power but no video signal. Since the user hears the Windows startup sound, the PC is booting; the most likely cause is a wrong input source or a disconnected/damaged video cable. Checking the input selection and cable is the fastest, least invasive first step.

Why this answer

The combination of audible Windows startup sound and an amber monitor LED strongly indicates the computer is running but the monitor is not receiving a video signal. The fastest non-invasive check is the monitor input source and cable. Confirming the correct HDMI/DisplayPort/VGA input and reseating both ends of the video cable typically resolves this scenario.

Exam trap

The trap here is assuming a black screen means the computer is dead, when audible startup sound and an amber monitor LED actually point to a display signal problem.

182
MCQmedium

A help desk technician is troubleshooting a user's Windows 11 laptop that cannot reach any website, though the user can ping 8.8.8.8 successfully. The technician runs ipconfig /all and sees the adapter has a valid IP address, correct subnet mask, and default gateway, but the DNS server field is empty. What should the technician do NEXT?

A.Run ipconfig /release followed by ipconfig /renew
B.Flush the DNS resolver cache with ipconfig /flushdns
C.Configure a valid DNS server address on the adapter
D.Replace the Ethernet cable connecting the laptop
AnswerC

Successful pings to 8.8.8.8 prove IP connectivity and routing are working, so the failure is name resolution. With an empty DNS server field, the client has no resolver to translate hostnames to IPs. Manually assigning a known-good DNS server (corporate or public) restores name resolution and immediately allows website access.

Why this answer

The ability to ping a public IP address confirms Layer 3 connectivity and routing are intact, narrowing the fault to DNS. An empty DNS server field means the client has no resolver configured, so hostname lookups fail while IP-based communication succeeds. Assigning a valid DNS server address on the adapter restores name resolution and web browsing.

Exam trap

The trap here is jumping to ipconfig /flushdns for any browsing failure, when an empty DNS server field requires configuring a resolver, not clearing cache.

183
Multi-Selectmedium

A user reports that their Windows 10 workstation takes a long time to start up and that several unwanted programs launch automatically after sign-in. A technician wants to reduce startup time and stop unnecessary programs from launching. Which TWO actions should the technician take? (Choose two.)

Select 2 answers
A.Review scheduled tasks in Task Scheduler for unnecessary triggers at logon.
B.Disable unnecessary entries in Task Manager's Startup tab.
C.Run the Disk Cleanup utility to remove temporary files.
D.Increase the size of the page file on the system drive.
E.Reinstall the operating system from installation media.
AnswersA, B

Task Scheduler can contain tasks configured to run at logon or startup, and some unwanted programs register tasks rather than Run key entries. Reviewing and disabling unnecessary logon-triggered tasks reduces the work performed during sign-in. Combined with disabling Startup tab entries, this covers both common mechanisms by which programs launch automatically on Windows 10.

Why this answer

Unwanted programs launch at sign-in through two primary mechanisms on Windows 10: entries in the Startup tab managed by Task Manager and tasks scheduled to run at logon in Task Scheduler. Disabling unnecessary entries in both locations reduces sign-in workload and stops the programs from launching. Together they address the reported symptom without uninstalling software or making destructive changes to the system.

Exam trap

The trap here is assuming that freeing disk space or reinstalling Windows will stop programs from auto-launching, when the actual mechanisms are Startup tab entries and logon-triggered scheduled tasks.

184
MCQmedium

Refer to the exhibit. A technician is attempting to repair disk errors on the primary system partition. Why does the system prompt the user to schedule the check upon restart?

A.The partition is encrypted with BitLocker.
B.The system partition is currently locked by a third-party antivirus.
C.Exclusive access to the file system is required for structural repairs.
D.The user lacks administrative privileges to run chkdsk.
AnswerC

The chkdsk utility needs to perform read/write operations on the file system structure that cannot occur while the kernel is actively reading or writing to the disk. Scheduling the task ensures that the repair process runs before the OS kernel mounts the partition, preventing data corruption or process interference.

Why this answer

The chkdsk tool requires exclusive access to the file system to perform repairs, which is impossible while the operating system is actively using the drive. By scheduling the check for the next boot, Windows performs the scan in an environment where the OS is not yet loaded, allowing full access to the partition's metadata and structure for reliable corruption detection and repair.

Exam trap

Candidates often assume chkdsk fails or bugs out when it prompts for a restart, not realizing exclusive file lock is mandatory for structural repairs.

185
MCQeasy

A user wants to change the default application for opening .pdf files on their Windows 11 computer. They right-click a PDF file and select 'Open with' > 'Choose another app', but the desired application is not listed. What should the user do next?

A.Open Settings > Apps > Default apps and select the desired application from the list.
B.Reinstall the desired application and then try again.
C.Click 'More apps' and then 'Look for another app on this PC' to browse for the executable.
D.Use the 'set default' button in the 'Open with' dialog to browse for the application.
AnswerC

The 'More apps' option expands the list of available applications, and 'Look for another app on this PC' allows the user to navigate to the executable file of the desired application. This is the correct method to select an application that is not automatically listed, ensuring the file association can be set.

Why this answer

When the desired application is not listed in the 'Open with' menu, the user can expand the list by clicking 'More apps' and then selecting 'Look for another app on this PC'. This opens a file browser where the user can locate the application's executable file, allowing them to set it as the default for .pdf files. Other methods either do not list unregistered apps or involve unnecessary steps.

Exam trap

The trap here is assuming that all installed applications automatically appear in the 'Open with' list; some may require manual browsing to the executable.

186
MCQeasy

A user reports that their desktop computer, which is connected to a Cisco Catalyst switch, cannot access the network. The technician notices that the switch port LED for that connection is off. What is the most likely cause?

A.The switch port is configured for a different VLAN.
B.The Ethernet cable is disconnected or faulty.
C.The switch port is shut down in the configuration.
D.The computer's network interface card (NIC) is disabled.
AnswerB

A switch port LED that is off indicates no link is established. This is most commonly caused by a disconnected or faulty cable. Without a physical link, the switch cannot communicate with the device, so the LED remains off. Checking the cable is the first troubleshooting step.

Why this answer

The switch port LED being off indicates that there is no physical link between the switch and the computer. The most common reason for this is a disconnected or faulty Ethernet cable. While other issues like a disabled NIC or shutdown port could also cause no link, a cable problem is the most likely and should be checked first.

Exam trap

The trap here is jumping to configuration issues like VLAN or port shutdown when the LED off indicates a physical layer problem.

187
MCQeasy

A user submits a ticket stating that their wireless mouse stopped responding after they replaced its batteries. The help desk technician confirms the mouse power switch is on and the receiver is still plugged into the same USB port. Which troubleshooting step should the technician try next?

A.Uninstall the mouse driver from Device Manager and reboot the workstation.
B.Move the mouse to a different USB port and test it on another computer.
C.Press and hold the pairing button on the receiver and the mouse to re-establish the wireless link.
D.Replace the USB receiver with a new one from a different mouse model to see if it detects.
AnswerC

Replacing batteries can break the pairing or cause the device to lose its channel association, so re-pairing the mouse to its receiver is the logical next step. This is a low-risk, quick action that addresses the most likely cause after a power cycle. If pairing fails, the technician can then test the receiver in another port or try a spare mouse.

Why this answer

After a battery change, a wireless mouse often loses its pairing with the USB receiver or drops to a channel that no longer communicates. Re-pairing the mouse and receiver restores the link without replacing hardware or reinstalling software. This step is fast, reversible, and directly targets the most probable cause, allowing the technician to escalate only if pairing does not resolve the issue.

Exam trap

The trap here is jumping to driver reinstallation or hardware replacement when a simple re-pairing step after a battery change is the most likely fix.

188
MCQmedium

A company subscribes to a SaaS customer relationship management application. The IT support technician is asked to explain to management which responsibilities remain with the company under the shared responsibility model for this SaaS deployment. Which area is the company still responsible for?

A.Applying hypervisor patches to the hosts that run the SaaS tenants
B.Managing user accounts, authentication, and the data the company uploads
C.Maintaining the physical servers and network fabric in the provider's data center
D.Patching the operating system that hosts the SaaS application
AnswerB

Under the shared responsibility model, the SaaS provider secures the application and infrastructure, but the customer remains accountable for its own identities, access control, and data. Creating user accounts, enforcing strong authentication, and classifying the CRM records stored in the service are squarely customer duties in this deployment.

Why this answer

Shared responsibility shifts with the service model. For SaaS, the provider secures everything from the physical facility up through the application, while the customer owns identity management, access control, endpoint security, and the data placed into the service. Managing user accounts and protecting uploaded CRM records therefore remains a company duty.

Exam trap

The trap here is assuming that because the application is fully managed, the customer has no security duties at all, when identity and data always stay with the customer.

189
MCQeasy

Which component in a Cisco switch is responsible for providing the necessary electrical power to internal circuitry while converting AC input to DC output?

A.Backplane
B.Power Supply Unit
C.Supervisor Engine
D.ASIC
AnswerB

The PSU handles the conversion of standard AC mains voltage to the specific DC voltages required by the internal switch components. A properly functioning PSU is critical to the operation of the device, and failure of this component will cause the switch to stop functioning entirely.

Why this answer

Understanding the function of power components is fundamental to hardware troubleshooting. The Power Supply Unit (PSU) serves as the bridge between facility power and the device's internal components. Knowing how to differentiate between power supplies, such as AC versus DC units, is essential for data center planning, as miscalculating power requirements or using incompatible modules can lead to device failure or potential electrical hazards during operation.

Exam trap

Candidates sometimes confuse internal logic elements like the CPU or NVRAM with hardware components specifically dedicated to power conversion and electrical distribution within a network switch.

190
MCQmedium

An employee receives an email that appears to come from the CEO asking for an urgent wire transfer to a new vendor, and the message asks the employee to keep it confidential until the transfer completes. Which social engineering principle is the attacker primarily exploiting?

A.Authority and urgency
B.Shoulder surfing
C.Tailgating
D.Dumpster diving
AnswerA

The message impersonates the CEO, which invokes authority, and demands an urgent transfer, which invokes urgency. The confidentiality request further pressures the employee to act without verifying through normal approval channels. These combined levers are the defining traits of business email compromise, making authority and urgency the principles being exploited here.

Why this answer

Impersonating the CEO establishes authority, and the demand for an immediate wire transfer creates urgency that discourages verification. The confidentiality instruction removes the natural safeguard of consulting colleagues or following standard approval steps. Together, authority and urgency are the social engineering levers that make business email compromise effective, which is why they are the correct pairing for this scenario.

Exam trap

The trap here is focusing on the email channel and calling it phishing, when the question asks which psychological principle the message exploits, which is authority combined with urgency.

191
Multi-Selectmedium

Which TWO of the following technologies help mitigate Layer 2 attacks in a switched network?

Select 2 answers
A.DHCP Snooping
B.RIPv2 Routing
C.Port Security
D.BGP Peer Authentication
E.ICMP Redirects
AnswersA, C

DHCP Snooping prevents unauthorized DHCP servers from providing IP information to clients. By building a binding database of trusted ports and IP-MAC mappings, it mitigates man-in-the-middle attacks and prevents rogue servers from disrupting network services, making it a key tool for layer-two security management.

Why this answer

Layer 2 attacks, such as VLAN hopping or DHCP starvation, exploit vulnerabilities in common link-layer protocols. Technologies like DHCP Snooping and Port Security provide essential defenses by validating traffic and limiting the number of devices per port. Implementing these features is critical for maintaining network integrity, as they prevent common L2 exploits that could otherwise lead to unauthorized access, traffic interception, or service disruptions for other users on the local broadcast domain.

Exam trap

Candidates often select higher-layer protocols like IPsec or SSL, forgetting that DHCP Snooping and Port Security specifically target vulnerabilities unique to Layer 2 switching environments.

192
MCQmedium

Refer to the exhibit. What is the effect of this configuration on interface Gi0/1?

A.The port remains active but drops traffic from unknown MAC addresses.
B.The port shuts down if more than one device attempts to connect.
C.The port restricts traffic to only the first device detected and logs the event.
D.The port will reset every time a new MAC address is detected.
AnswerB

With the maximum set to 1 and the violation mode set to shutdown, the switch detects the violation as soon as a second unauthorized MAC address is seen. The interface then moves to an error-disabled state, effectively disconnecting the port to protect the network from unauthorized devices.

Why this answer

The configuration forces the port to accept only one MAC address. If a second device attempts to connect, the interface will automatically transition to an error-disabled state. This implementation is effective for preventing unauthorized devices from gaining network access.

This security posture is important because it forces administrative intervention if a violation occurs, ensuring the network manager is alerted to potential physical security breaches at the switch layer.

Exam trap

Candidates mistakenly believe that port security violations merely drop the offending packet or generate a log, overlooking the default behavior of transitioning to an error-disabled state.

193
MCQeasy

What is the primary function of the 'Mode' button on the front panel of a Cisco Catalyst switch?

A.To factory reset the switch configuration.
B.To toggle the LED display between different status modes.
C.To put the switch into a power-saving sleep mode.
D.To initiate a console session via the Ethernet port.
AnswerB

Pressing the Mode button allows the technician to cycle through various status indicators, such as System, RPS, PoE, and Speed. This provides a convenient way to check different hardware parameters visually without requiring a serial connection or network access to the switch's command line interface.

Why this answer

The Mode button is a physical interface feature that allows technicians to change the information displayed by the port LEDs. Understanding this physical control is vital for status monitoring without needing console access. It enables quick identification of duplex status, speed, or PoE availability, providing an immediate visual assessment of the switch's health and configuration in a data center environment.

Exam trap

Candidates often assume the Mode button is used to reset the device or change configuration settings. They fail to realize it is purely a visual diagnostic tool for the LED indicators.

194
MCQhard

Refer to the exhibit. A technician sees this JSON policy applied in a cloud environment. What is the expected behavior for traffic originating from 192.168.1.50 destined for Cloud_Storage?

A.Traffic will be allowed and logged
B.Traffic will be dropped with a log entry generated
C.Traffic will be silently dropped without logging
D.The policy is invalid because JSON cannot define security rules
AnswerB

The policy matches the source subnet containing the host and triggers the 'DENY' action. Because 'log' is set to 'ENABLED', the cloud security system will drop the packet and generate a log entry, allowing administrators to audit the attempt and verify that the security policy is being enforced correctly.

Why this answer

The policy 'Restricted_Access' is defined with an action of 'DENY' for the entire subnet '192.168.1.0/24'. Since 192.168.1.50 falls within this range, the traffic will be blocked by the cloud security policy. The 'log: ENABLED' setting ensures that this block event will be recorded in the security logs, which is a critical step for troubleshooting connectivity issues in cloud-based infrastructure deployments.

Exam trap

Candidates often misread explicit deny statements or ignore subnet mask ranges, incorrectly guessing that traffic will be allowed if logging is enabled.

195
MCQmedium

A user's laser printer displays a 'Load Tray 1' message even though Tray 1 is filled with the correct paper size. The technician notices the paper guides are set slightly wider than the stack. Which action should the technician take to clear the message?

A.Adjust the tray guides so they press snugly against the paper stack
B.Replace the entire paper tray with a spare unit from inventory
C.Power cycle the printer to reset the paper sensor firmware
D.Run the printer's automatic color calibration routine
AnswerA

Many laser printers use a sensor or switch that detects whether the guides are positioned against the media. Guides set too wide can prevent the tray from registering paper, triggering a load message despite a full tray. Snugging the guides against the stack restores the sensor's detection and clears the prompt without replacing parts or media.

Why this answer

Laser printers detect media presence through sensors tied to the tray's guide positions. When guides are set wider than the stack, the tray can fail to register paper and the printer prompts the user to load it. Snugging the guides against the paper corrects the mechanical condition and clears the message without parts replacement or firmware resets.

Exam trap

The trap here is treating a mechanical tray sensor issue as a firmware or hardware failure and replacing parts when the guides simply need repositioning.

196
MCQmedium

Which protocol is most commonly used to provide secure remote management access to a Cisco device, replacing the insecure Telnet protocol?

A.SNMPv1
B.HTTP
C.SSH
D.FTP
AnswerC

SSH is the industry standard for secure remote administrative access. It encrypts the entire communication session, protecting usernames, passwords, and command output from eavesdropping. It is the secure replacement for Telnet and is essential for maintaining the security of the management plane on any network device in an enterprise.

Why this answer

SSH (Secure Shell) provides encrypted remote access to network device CLIs. Telnet transmits all data, including administrative passwords, in plaintext, making it highly vulnerable to interception. SSH uses cryptographic keys to establish a secure channel, ensuring confidentiality and integrity for all management traffic.

It is a mandatory security practice for any remote management solution in modern IT environments to prevent credential theft and unauthorized access.

Exam trap

Candidates occasionally confuse administrative management protocols with tunneling protocols like IPsec or encrypted web browsing protocols like HTTPS.

197
MCQeasy

You are deploying a new application to multiple macOS devices. Which file format is the industry standard for installing software on macOS in an enterprise environment?

A..dmg
B..pkg
C..app
D..iso
AnswerB

The .pkg installer is the standard format for automated software deployment. It allows administrators to run pre- and post-installation scripts, manage dependencies, and ensure the software is installed in the correct directory without user interaction, making it the ideal choice for large-scale enterprise environments and MDM-driven workflows.

Why this answer

The .pkg format is the standard for enterprise deployments. Unlike the .dmg format, which is primarily intended for manual user dragging and dropping, .pkg files can be signed, verified, and distributed via MDM solutions. This allows for automated, unattended installations, which is critical for maintaining consistency and security across a large fleet of managed devices in a professional workplace.

Exam trap

Candidates frequently choose '.dmg' because it is common for personal use. They fail to realize that '.dmg' files are not suitable for silent, automated, or MDM-based enterprise software deployment.

198
Multi-Selectmedium

Which THREE of the following are considered valid methods for connecting to a Cisco router for management purposes? (Choose three.)

Select 3 answers
A.Console port
B.USB port
C.AUX port
D.HDMI port
E.VGA port
AnswersA, B, C

The console port provides direct, out-of-band access to the router. It is the primary method for initial device setup and for recovering access when remote network connections are down. It operates independently of the IP stack, making it an essential tool for troubleshooting severe device misconfigurations.

Why this answer

Network administrators must understand the various ways to access Cisco devices, as physical and logical access methods are critical for configuration and troubleshooting. Whether using out-of-band management via the console or in-band management via SSH or Telnet, each method requires specific hardware and software configurations. Understanding these paths ensures that access is always available, even if one method fails or the network layer is currently unreachable.

Exam trap

Candidates often include logical methods like SSH or Telnet when the question asks for physical management connections. They fail to distinguish between out-of-band hardware ports and in-band network protocol access.

199
MCQhard

A Windows workstation is failing to boot and displays a 'Boot Device Not Found' error. You have already verified the hardware cabling. Which command-line tool, when run from the Windows Recovery Environment (WinRE), is most effective for repairing the Master Boot Record (MBR) and the Boot Configuration Data (BCD) store?

A.chkdsk
B.bootrec
C.sfc
D.diskpart
AnswerB

Bootrec.exe is specifically designed to troubleshoot and repair boot-related issues by interacting with the MBR, the partition boot sector, and the BCD store. It is the industry-standard tool for resolving startup failures where the system cannot find a bootable device or configuration.

Why this answer

Bootrec.exe is the primary command-line tool for troubleshooting startup issues in Windows. By using parameters like /fixmbr and /rebuildbcd, technicians can repair corrupted boot records and recreate the BCD store. Mastering this tool is crucial for IT support because boot-related errors are common, and the ability to restore access to the OS without data loss is a core competency.

Exam trap

Candidates often suggest 'chkdsk' or 'sfc'. While useful for file system errors, they do not resolve boot configuration issues specifically related to the MBR or BCD store.

200
MCQeasy

Which cloud service model provides the customer with control over the operating system, applications, and storage, but leaves the physical hardware management to the provider?

A.SaaS
B.PaaS
C.IaaS
D.DaaS
AnswerC

Infrastructure as a Service (IaaS) provides the highest level of flexibility and management control. The customer is responsible for managing the operating system, applications, and network configuration within the virtualized instance, while the cloud provider ensures the underlying physical servers, storage arrays, and network fabric are fully operational and secure.

Why this answer

Infrastructure as a Service (IaaS) provides virtualized computing resources over the internet. The provider maintains the physical servers, storage, and networking hardware, while the customer manages the operating system, middleware, and application runtime. This model is ideal for enterprises that want to avoid the high cost of physical data center maintenance while retaining full administrative control over their software environment and security configuration.

Exam trap

Candidates mix up IaaS, PaaS, and SaaS responsibilities, often assuming that managing the operating system implies full physical hardware control as well.

201
MCQmedium

Refer to the exhibit. What effect does this ACL have on traffic?

A.It allows all HTTP traffic from any subnet.
B.It allows HTTP traffic only from the 192.168.1.0/24 subnet.
C.It denies all traffic from the 192.168.1.0/24 subnet.
D.It permits all traffic from 192.168.1.0/24 to any destination.
AnswerB

The ACL entry 'permit tcp 192.168.1.0 0.0.0.255 any eq 80' explicitly matches traffic from the defined subnet to any destination on port 80. Since it is followed by a 'deny ip any any', all other traffic is blocked, enforcing strict access control for the internal subnet.

Why this answer

The ACL permits traffic originating from the 192.168.1.0/24 subnet to access any destination on port 80 (HTTP). The second line explicitly denies all other IP traffic. This is a common implementation of a least-privilege security policy, allowing only specific web traffic and blocking everything else.

It is important for restricting internal segments to only necessary services, significantly reducing the potential for unauthorized data exfiltration or internal lateral movement.

Exam trap

Students often misinterpret standard ACL source and destination directions, assuming the permit rule applies globally to all subnets rather than only the specified source.

202
Multi-Selecthard

A technician is troubleshooting a desktop PC that intermittently powers off during heavy load. The power supply is rated at 500W. Which two components are most likely to cause this issue? (Choose two.)

Select 2 answers
A.Overheating CPU
B.Loose graphics card
C.Faulty RAM
D.Failing power supply
E.Insufficient wattage for the system's components
AnswersD, E

A failing power supply can cause intermittent shutdowns under load when it cannot deliver stable voltage or sufficient current. Capacitors may be degraded, leading to voltage drops. This is a common cause of random power-offs during high demand.

Why this answer

The two most likely causes are a failing power supply and insufficient wattage for the system's components. Both relate to the power supply's inability to provide stable power under heavy load. A failing unit may have degraded capacitors, while insufficient wattage means the system exceeds the supply's capacity.

Other components like RAM or CPU overheating would produce different symptoms.

Exam trap

The trap here is attributing power-offs to other components like RAM or CPU, when the intermittent nature under load strongly suggests power delivery issues.

203
MCQmedium

An organization is deploying a hybrid cloud strategy. What is the primary purpose of a cloud connector in this environment?

A.To increase the physical RAM on the local server
B.To provide a secure bridge between on-premise and public clouds
C.To replace the need for a firewall at the network edge
D.To cache all web traffic for faster Internet browsing
AnswerB

The cloud connector acts as a secure gateway or tunnel, ensuring that traffic between the private and public clouds is encrypted and authenticated. It allows the enterprise to extend its internal network policies and identity services into the public cloud, creating a unified hybrid environment that is manageable and secure.

Why this answer

A cloud connector functions as an intermediary device or software agent that links an on-premise private data center to a public cloud environment. It facilitates secure communication, identity propagation, and traffic routing between the two environments. This is crucial for hybrid architectures where workloads are distributed across both private infrastructure and public services, ensuring consistent security policies and seamless connectivity for users accessing resources regardless of their physical location.

Exam trap

Test-takers mistakenly believe a cloud connector replaces local firewalls or acts as a local storage array, missing its core inter-network bridging function.

204
MCQeasy

A user is unable to install a required application on their Windows workstation. Upon investigation, you find that the installer requires administrator privileges. Which feature allows you to run the installer with elevated permissions without changing the user's standard account type?

A.User Account Control (UAC)
B.Run as administrator
C.Group Policy Object (GPO)
D.Compatibility Mode
AnswerB

This feature allows a user to execute a specific application or installer with elevated privileges. It is the correct and safest way to perform software installations on a standard user account, ensuring that the user does not have persistent administrative rights that could lead to system damage.

Why this answer

Running an application as an administrator is a standard practice for installing software while maintaining the principle of least privilege for daily tasks. By using the 'Run as administrator' context menu option, you temporarily elevate privileges for that specific process. This protects the system from accidental changes by the user while still allowing legitimate administrative tasks to be completed successfully.

Exam trap

Candidates often select changing the user account type to administrator, violating the principle of least privilege, instead of utilizing temporary execution elevation.

205
MCQhard

An IT support technician needs to configure a macOS Ventura endpoint to automatically log out the user after 15 minutes of inactivity, as required by corporate policy. Which method should the technician use?

A.Modify the 'Security & Privacy' preferences to require password immediately after sleep.
B.Use the 'Energy Saver' preferences to set display sleep to 15 minutes.
C.Create a launchd agent that runs 'pkill -u $USER' every 15 minutes.
D.Use a configuration profile with a 'Login Window' payload to set 'Log out after inactivity'.
AnswerD

A configuration profile with the Login Window payload can enforce automatic logout after a specified period of inactivity. This is the standard method for managed macOS endpoints to meet security policies. It ensures the user is logged out, not just the display sleeping. This setting can be deployed via MDM or manually installed, and it applies system-wide.

Why this answer

To enforce automatic logout after inactivity on macOS, the correct method is to deploy a configuration profile with the Login Window payload, which includes the 'Log out after inactivity' setting. This is designed for managed environments and can be deployed via MDM. It ensures the user is logged out after the specified idle time, meeting security requirements without disrupting active sessions.

Exam trap

The trap here is confusing display sleep or password-after-sleep with actual logout, which are different security controls.

206
MCQmedium

Which security threat involves an attacker sending a large number of spoofed requests to a service to make it unavailable to legitimate users?

A.Man-in-the-Middle
B.Denial of Service
C.Phishing
D.VLAN Hopping
AnswerB

A Denial of Service (DoS) attack specifically seeks to prevent legitimate users from accessing resources by overwhelming the system with traffic or requests. By exhausting bandwidth or processing power, the attacker successfully denies service to those who need it, fitting the definition provided in the question.

Why this answer

A Denial of Service (DoS) attack aims to overwhelm a target by flooding it with malicious traffic. This causes the target to exhaust its resources and eventually crash or stop responding. Understanding DoS is crucial because it is one of the most common and damaging threats to network availability.

Implementing rate limiting and traffic filtering is necessary to maintain business continuity and protect critical services from being knocked offline by malicious actors.

Exam trap

Candidates often confuse DoS with DDoS or physical attacks. They fail to recognize that the core definition of a DoS attack is specifically about resource exhaustion and service unavailability.

207
Multi-Selecthard

A help desk technician is troubleshooting a user's Windows workstation that repeatedly displays a blue screen with a stop code after a new peripheral was installed. The technician suspects a driver conflict. Which TWO actions should the technician take to diagnose and resolve the issue? (Choose two.)

Select 2 answers
A.Reinstall the operating system from scratch.
B.Boot into Safe Mode and check Device Manager for devices with warning icons.
C.Run a full disk defragmentation on the system drive.
D.Roll back or uninstall the driver for the newly installed peripheral.
E.Disable the Windows Error Reporting service.
AnswersB, D

Safe Mode loads a minimal set of drivers, which can isolate whether a third-party driver is causing the crash. Device Manager in Safe Mode may show devices with warning icons or error codes that point to the problematic driver. This is a safe, diagnostic step that helps identify the conflict before making changes, and it directly addresses the suspicion of a driver issue.

Why this answer

Because the blue screens started right after a new peripheral was installed, the driver for that device is the most probable cause. Booting into Safe Mode and inspecting Device Manager isolates the faulty driver, while rolling back or uninstalling it removes the trigger. Together these steps diagnose and resolve the conflict without resorting to drastic measures like an OS reinstall.

Exam trap

The trap here is treating a new-peripheral blue screen as a general Windows corruption issue instead of focusing on the recently added driver.

208
MCQmedium

A network administrator needs to host multiple virtual machines on a single physical Cisco UCS server. Which technology allows these VMs to share the physical NIC while maintaining traffic isolation?

A.Port Security
B.Access Control Lists
C.VLAN Tagging (802.1Q)
D.DHCP Snooping
AnswerC

802.1Q VLAN tagging inserts a header into Ethernet frames, allowing the virtual switch to map traffic to specific isolated networks. This enables multiple virtual machines to utilize a single physical network interface card while maintaining distinct, secure, and isolated broadcast domains for each specific virtual network segment defined.

Why this answer

Virtual Local Area Networks (VLANs) combined with virtual switching allow physical NICs to be partitioned into logical segments. By tagging traffic at the virtual switch level, the hypervisor ensures that traffic from different VMs remains isolated despite sharing the same physical uplink. This is essential for scaling data center resources efficiently while maintaining strict security boundaries between production, development, and management traffic segments in virtualized environments.

Exam trap

Test-takers frequently confuse physical port bonding or standard routing protocols with VLAN tagging, forgetting that 802.1Q is specifically designed to segment traffic logically across shared physical links.

209
MCQhard

Refer to the exhibit. A JSON-based security policy is applied to a virtual firewall. What is the effect of this policy on traffic directed toward the 10.0.0.0/8 network?

A.Traffic is permitted but logged.
B.Traffic is blocked.
C.Traffic is redirected to a honeypot.
D.The policy is syntactically invalid.
AnswerB

The JSON policy defines an action of 'block' for all source traffic destined for the 10.0.0.0/8 network. Since the source is set to 'any', this rule acts as a blanket restriction, effectively dropping all packets attempting to access the internal 10.0.0.0/8 range at the firewall level.

Why this answer

The policy explicitly sets the 'action' to 'block' for any traffic sourced from 'any' destined for the 10.0.0.0/8 range. This is a standard deny-all rule for a specific internal subnet. In a virtualized environment, such policies are often managed via API calls or automation scripts to enforce micro-segmentation.

Understanding how these JSON structures dictate traffic flow is critical for verifying security postures and troubleshooting connectivity issues within cloud-native architectures.

Exam trap

Candidates often overthink the JSON structure, searching for complex logic. They ignore the explicit 'action: block' parameter, which is the most straightforward indicator of the policy's outcome.

210
MCQeasy

A support technician receives a call from a remote employee who cannot connect to the corporate VPN client. The user reports receiving an authentication failure error immediately after entering credentials. What is the most appropriate initial troubleshooting action for the help desk technician?

A.Reboot the corporate hardware firewall protecting the main enterprise data center
B.Uninstall and reinstall the third-party VPN client software on the remote laptop
C.Verify the user credentials against the centralized authentication directory and check for account lockouts
D.Modify the client registry to disable all local host firewall security services
AnswerC

Verifying the user credentials and checking for account lockouts targets the most frequent source of immediate authentication failures during remote connection attempts. Active Directory or RADIUS logs provide precise insight into whether the password expired, the account was locked due to failed attempts, or multi-factor authentication failed.

Why this answer

Confirming account status and active directory lockout policies addresses the most common cause of sudden VPN authentication failures. Remote workers frequently trigger account lockouts due to cached passwords on mobile devices or typing errors. Verifying credentials on an internal portal or checking authentication logs helps the technician quickly isolate whether the problem is user error or a server-side authentication failure.

Exam trap

Candidates often assume the VPN software is corrupted or the server is down, leading them to suggest reinstalling the client software before verifying the simple status of the user's account.

211
MCQhard

Refer to the exhibit. A technician is troubleshooting a VPN connection. What does the status 'ACTIVE' in this configuration imply?

A.The VPN tunnel itself is currently established
B.The service policy is successfully applied to the interface
C.The Management VRF is blocking all VPN traffic
D.The interface Gig0/1 is physically down
AnswerB

In Cisco policy-based configurations, an 'ACTIVE' status confirms that the service policy has been successfully mapped to the interface and that the router has loaded the rules into the operational data plane. It confirms the configuration path is correct, narrowing the troubleshooting scope to the policy rules themselves.

Why this answer

The 'ACTIVE' status indicates that the interface 'Gig0/1' is currently successfully assigned to the 'Management' VRF and that the 'VPN_INBOUND' service policy is currently applied and functioning on that interface. This means the router is actively enforcing the rules defined in that policy for incoming traffic. If a VPN user cannot connect, the technician knows the policy is applied and should look for issues within the specific VPN_INBOUND policy rules.

Exam trap

Candidates frequently mistake an interface policy status for user authentication success, assuming an 'ACTIVE' service policy means specific client logins work.

212
MCQeasy

A remote user's MacBook Air will not wake from sleep when the lid is opened, though the power indicator shows the battery is charged. The user has already tried pressing keys and the trackpad. Which built-in macOS utility should the technician guide the user to open first to review recent wake and sleep events?

A.Activity Monitor, using the Energy tab to inspect wake assertions.
B.Console, filtering for power management and wake-related log messages.
C.Disk Utility, verifying the startup disk for errors that block wake.
D.System Information, reviewing the Power section for battery cycle count.
AnswerB

Console aggregates the unified logging system, where power management subsystems record sleep, wake, and lid-open events with timestamps and reasons. Filtering for terms such as 'Wake' or 'Sleep' reveals whether the lid-open generated a wake request and what blocked it. This directly answers why the Mac did not wake, making Console the appropriate first utility for this symptom.

Why this answer

Wake and sleep transitions are recorded by the power management subsystem in the unified log. Console is the built-in utility that exposes those timestamped entries, letting the technician see whether the lid-open produced a wake request and which assertion or device blocked it. Activity Monitor, Disk Utility, and System Information report current energy use, disk health, and battery condition respectively, none of which capture the wake event history required here.

Exam trap

The trap here is reaching for a monitoring tool that shows present power state instead of the logging utility that preserves the history of why a wake did or did not occur.

213
MCQeasy

What is the purpose of the 'show inventory' command on a Cisco device?

A.Displays the current running configuration.
B.Lists installed physical hardware modules.
C.Provides real-time traffic statistics.
D.Tests the integrity of the IOS image.
AnswerB

This command outputs a list of all physical hardware entities, such as line cards, power supplies, and fans, along with their associated PIDs and serial numbers. It is the primary tool for verifying that physical upgrades or replacements have been correctly installed and are detected by the IOS.

Why this answer

The 'show inventory' command provides a detailed list of all physical components installed in the chassis, including serial numbers and product IDs. This is vital for asset management, verifying hardware upgrades, and troubleshooting potential physical component failures. Technicians use this command to ensure that the correct hardware modules are recognized by the system and to track support contracts, ensuring reliable operations across the network infrastructure.

Exam trap

Candidates often confuse 'show inventory' with 'show version' or 'show running-config'. They expect it to display software versions or configuration settings rather than physical hardware serial numbers and modules.

214
Multi-Selecthard

A help desk technician is investigating a report where multiple workstations on an access switch cannot reach devices on other VLANs. The physical connections and local workstation IP configurations are verified as correct. Which TWO switch configurations or status items should the technician inspect to resolve this inter-VLAN routing issue? (Choose two)

Select 2 answers
A.Verify that the switch virtual interface (SVI) for each VLAN is created and in the 'up/up' state
B.Inspect the physical link status and duplex settings of the workstation access ports
C.Verify that the uplink port connecting the access switch to the core router is configured as a trunk port
D.Reinstall the local workstation network interface card drivers across all affected computers
E.Check the local workstation host file for incorrect IP-to-hostname mappings
AnswersA, C

Switch Virtual Interfaces act as default gateways for VLANs on multilayer switches. If an SVI is missing, unconfigured, or in a down/down state, inter-VLAN routing cannot occur because devices lack a valid default gateway to forward traffic between subnets.

Why this answer

Inter-VLAN communication requires a Layer 3 routing device, such as a multilayer switch or router using router-on-a-stick, to forward traffic between broadcast domains. Inspecting trunk port configurations and SVI status ensures that inter-VLAN traffic is properly tagged and routed across the network infrastructure. These checks isolate configuration errors from hardware failures.

Exam trap

Test-takers frequently assume default gateway configurations on individual workstations are at fault, missing that inter-VLAN routing requires functional Layer 3 SVIs and properly configured trunk links on the switches.

215
MCQmedium

A company wants to provide remote users with access to internal web applications without installing a VPN client on each device. The security team requires that users authenticate through the corporate identity provider before reaching the applications. Which solution best meets these requirements?

A.A site-to-site IPsec tunnel between branch offices
B.Remote Desktop Gateway with per-user RDP sessions
C.A client-based IPsec VPN with full-tunnel mode
D.A clientless SSL VPN portal integrated with the identity provider
AnswerD

A clientless SSL VPN portal lets users reach internal web applications through a browser after authenticating, often via SAML or OIDC against the corporate identity provider. It requires no per-device VPN client and enforces authentication before granting access. This directly satisfies both the clientless requirement and the identity provider authentication requirement.

Why this answer

A clientless SSL VPN portal allows remote users to access internal web applications through a browser without installing a VPN client, and it can integrate with the corporate identity provider for authentication. Site-to-site tunnels, client-based IPsec VPNs, and Remote Desktop Gateway each fail to meet the combination of clientless access and identity provider authentication for specific web applications.

Exam trap

The trap here is equating any secure remote access method with clientless web access, when client-based VPNs and RDP gateways still require installed software.

216
MCQmedium

A user receives a phone call from someone claiming to be from the IT help desk. The caller says a virus was detected on the user's workstation and asks the user to read back the six-digit code just sent by text message so the technician can 'remote in and clean it.' The user has not reported any problem. Which security concept best describes this attack?

A.A denial-of-service flood against the help desk phone system
B.A watering hole attack targeting a frequently visited website
C.A smishing campaign delivering a malicious link over SMS
D.Vishing used to bypass multifactor authentication
AnswerD

The attacker uses a voice phone call, which is vishing, and the six-digit code is a one-time passcode from a multifactor authentication system. Convincing the user to read that code aloud defeats the second factor because the attacker can then complete a login with the stolen password plus the code. The social pressure and the live phone channel are the defining characteristics here.

Why this answer

Reading a one-time passcode to a caller hands the attacker the second factor needed to complete a login with credentials they already hold or are about to obtain. Because the request arrives by voice and exploits trust in the help desk, it is vishing, and its purpose is to bypass multifactor authentication rather than to deliver malware or disrupt a service.

Exam trap

The trap here is classifying the event by the text message channel and calling it smishing, when the code is legitimate and the actual attack arrives through the voice call.

217
MCQeasy

Which feature in macOS allows you to securely share files between nearby Apple devices without using a network or cloud storage?

A.iCloud Drive
B.AirDrop
C.FileVault
D.Handoff
AnswerB

AirDrop is the native macOS feature that enables encrypted, peer-to-peer file sharing between Apple devices in close physical proximity. It uses Bluetooth to discover devices and Wi-Fi to create a direct link, providing a secure, high-speed method for transferring data without needing an intermediary network or cloud service.

Why this answer

AirDrop is a key feature of the Apple ecosystem, utilizing Bluetooth and Wi-Fi for proximity-based file transfers. For IT support, knowing how to enable or troubleshoot AirDrop is essential for assisting users who need to move files quickly and securely between managed corporate devices. It is a fundamental part of the macOS experience that reduces reliance on insecure email attachments or external physical storage media.

Exam trap

Candidates often select generic cloud sharing or network protocols instead of the native peer-to-peer ecosystem feature built specifically for nearby Apple devices.

218
MCQeasy

Which cable type is typically used for a console connection between a technician's laptop and a Cisco network device?

A.Crossover cable
B.Rollover cable
C.Straight-through cable
D.Fiber optic patch cord
AnswerB

The rollover cable, also known as a console cable, features a pinout that is reversed on one end compared to the other. This specific wiring is essential for the serial communication required to interact with the device's command-line interface directly from an external management terminal or laptop.

Why this answer

The rollover cable, often referred to as a console cable, is the standard for accessing the CLI of Cisco hardware. Recognizing the correct physical cabling is fundamental for any technician performing initial configurations. Using an incorrect cable type can result in a failure to establish a terminal session, preventing the technician from managing the device and potentially delaying critical network setup tasks or troubleshooting efforts.

Exam trap

Many candidates incorrectly choose straight-through or crossover Ethernet patch cables, forgetting that connecting a laptop serial/USB port to a Cisco device console port requires a specialized rollover cable.

219
MCQeasy

A help desk technician receives a call from an employee who says they cannot open a file attachment in an email from an unknown sender. The email claims to be an invoice and urges immediate payment. The technician suspects a phishing attempt. Which action should the technician take first?

A.Instruct the employee to open the attachment in a sandboxed virtual machine to see if it is malicious.
B.Tell the employee to forward the email to the IT security team and then delete it from their mailbox.
C.Ask the employee to reply to the sender requesting verification of the invoice before taking any further action.
D.Instruct the employee to add the sender's email address to the blocked senders list and continue working.
AnswerB

Forwarding the suspicious email to the security team allows them to analyze the threat and block similar messages, while deleting it from the employee's mailbox prevents accidental interaction. This follows standard incident response procedures for suspected phishing. The technician should also remind the employee not to click links or open attachments, and to report any similar emails in the future.

Why this answer

The correct first action is to report the suspicious email to the IT security team and then delete it from the employee's mailbox. This prevents the employee from interacting with malicious content and allows security professionals to analyze the threat, block similar messages, and warn other users if necessary. Replying to or opening the attachment could put the organization at risk.

Exam trap

The trap here is assuming that the help desk technician should investigate the attachment themselves or that replying to the sender is a safe way to verify legitimacy.

220
MCQmedium

A network administrator is troubleshooting a Cisco Catalyst switch that fails to boot, showing a solid orange System LED. Which hardware component should the technician inspect first to determine if the issue is power-related versus internal firmware corruption?

A.Check the NVRAM for a valid startup-config file.
B.Inspect the physical power supply unit (PSU) connection and output.
C.Verify the status of the console cable connection.
D.Rebuild the flash memory partition using the rommon prompt.
AnswerB

A solid orange System LED often indicates a critical hardware failure or an incomplete boot process caused by insufficient power or faulty PSU hardware. Verifying physical power delivery is the first logical step to ensure the device has the electrical capacity to initialize its internal motherboard and components.

Why this answer

The System LED status is a primary diagnostic indicator for Cisco switches. A solid amber or orange light typically suggests a POST (Power-On Self-Test) failure or a hardware fault. Understanding how to interpret physical indicators allows technicians to isolate electrical issues from software-level bootloader failures quickly.

Identifying the state of hardware components before attempting manual recovery prevents unnecessary configuration wipes and reduces switch downtime during critical network maintenance tasks.

Exam trap

Candidates often jump to console-based troubleshooting or password recovery. They fail to perform the most basic physical step of verifying power supply integrity, which is the most common cause of boot failure.

221
MCQmedium

Refer to the exhibit. A technician is troubleshooting a report of 'slow network performance' from a user workstation. Based on the output, what is the most likely cause of the issue?

A.The target host is completely offline and unreachable.
B.There is significant packet loss occurring on the network path.
C.The round-trip time is too high for standard applications.
D.The IP address of the target host is configured incorrectly.
AnswerB

A 40 percent success rate indicates that three out of five packets were dropped before they could return to the source. This level of packet loss will cause applications to lag, file transfers to fail, and voice/video calls to drop, directly explaining the user's report of poor network performance and instability.

Why this answer

The ICMP echo request output shows intermittent connectivity, which is a classic symptom of packet loss. In a network environment, packet loss can be caused by congested links, failing hardware, or electromagnetic interference. Identifying the pattern of loss—in this case, 60% failure—helps the technician narrow down whether the issue is a total outage or a degraded signal path.

Exam trap

Candidates often misinterpret the output as a total network outage or a DNS failure because of the high failure rate, failing to recognize that intermittent ping results specifically indicate packet loss.

222
MCQhard

An organization wants to authenticate users connecting to the network using a centralized server. Which protocol allows for secure communication between the network access device and the authentication server?

A.SNMP
B.RADIUS
C.Telnet
D.HTTP
AnswerB

RADIUS provides a robust framework for AAA. It encrypts the password portion of the communication between the network access device and the server, ensuring that credentials are not transmitted in cleartext. This makes it the preferred protocol for secure, centralized user authentication in enterprise networks.

Why this answer

RADIUS (Remote Authentication Dial-In User Service) is the industry standard for centralized authentication, authorization, and accounting (AAA) in network environments. It enables network devices to communicate with a server like Cisco ISE or FreeRADIUS to verify user identities. By using RADIUS, organizations can enforce consistent security policies, audit user activity, and simplify credential management, which is essential for maintaining a secure and scalable network access infrastructure.

Exam trap

Students commonly confuse RADIUS with TACACS+ or local database authentication, missing the specific context of centralized network access device communication.

223
MCQmedium

A user is complaining that their Mac is running slowly. You want to check which processes are consuming the most CPU resources using the Terminal. Which command should you use?

A.ps -aux
B.top
C.vmstat
D.df -h
AnswerB

The 'top' command is the industry-standard tool for displaying real-time system metrics, including CPU utilization, memory consumption, and active process lists. It is the most appropriate command for observing fluctuations in performance and identifying problematic applications that may be hogging system resources in real-time.

Why this answer

The 'top' command provides a real-time, dynamic view of the running system, including CPU and memory usage per process. For an IT technician, being able to identify resource-hungry processes via the command line is essential for troubleshooting performance bottlenecks on headless systems or when the GUI becomes unresponsive. It is a standard diagnostic practice to verify if a specific application is hanging or causing high system load.

Exam trap

Candidates often suggest 'ps' or 'Activity Monitor'. While Activity Monitor works, it is a GUI tool; the question specifically asks for a Terminal command to check CPU usage.

224
MCQmedium

Which command-line utility is used on macOS to manage and view the current power management settings, including sleep and idle behavior?

A.powercfg
B.pmset
C.batteryctl
D.energy-save
AnswerB

The 'pmset' command is the standard macOS utility for managing power settings. It allows technicians to view and modify sleep timers, wake-on-LAN settings, and power profiles, making it the correct and primary tool for managing energy-related configuration changes via the command line on any macOS system.

Why this answer

The 'pmset' command is the native tool for modifying power management settings in macOS, such as display sleep, disk sleep, and system sleep. For IT support, this tool is essential for customizing the power behavior of workstations, especially in managed environments where power consumption policies are strictly defined for energy savings or to ensure that machines remain available for remote management tasks overnight.

Exam trap

Test-takers frequently guess generic system configuration tools or GUI settings panels instead of the specific command-line utility designed for macOS power management.

225
MCQeasy

Which cloud computing service model allows a developer to deploy applications without managing the underlying operating system, server hardware, or runtime environment?

A.Infrastructure as a Service (IaaS)
B.Software as a Service (SaaS)
C.Platform as a Service (PaaS)
D.Desktop as a Service (DaaS)
AnswerC

PaaS offers a development environment where the provider manages the OS, middleware, and hardware. This allows developers to focus purely on application logic and deployment, abstracting away the operational complexities of server management while providing scalable tools for building, testing, and deploying modern web applications.

Why this answer

Platform as a Service (PaaS) provides a framework that allows developers to focus exclusively on application code and data management. By abstracting the OS and infrastructure, PaaS enables faster deployment cycles. This service model is vital for modern DevOps workflows, as it reduces administrative overhead and allows teams to scale applications seamlessly without needing to maintain the underlying cloud infrastructure.

Exam trap

Candidates confuse PaaS with IaaS. They assume that because an application is deployed, it must be IaaS, forgetting that PaaS explicitly abstracts the OS and runtime environment management.

Page 2

Page 3 of 5

Page 4

All pages