- A
The VMkernel adapter must be in the same subnet as the destination host.
vMotion requires IP connectivity between hosts on the same subnet.
- B
The VMkernel adapter must be enabled for vMotion.
vMotion must be enabled on the VMkernel adapter.
- C
The physical uplinks must be in active/standby mode.
Why wrong: Teaming mode does not affect vMotion functionality.
- D
The port group must have VLAN ID 0.
Why wrong: VLAN ID can be any value; it doesn't have to be 0.
- E
The port group must be configured with a static IP address.
Why wrong: DHCP is possible, though not recommended.
Question 360 of 521
VCP-DCV Configure and Manage vSphere Networking Practice Question
This VCP-DCV practice question tests your understanding of configure and manage vsphere networking. Match the stated requirement to the specific cloud service, access model, or configuration option — many options are valid in isolation but not for this scenario. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Which two conditions must be met for a VMkernel adapter to be used for vMotion on a distributed switch? (Choose two.)
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
The VMkernel adapter must be in the same subnet as the destination host.
Options A and B are correct. The VMkernel adapter must be in the same subnet as the destination host (A) to allow vMotion traffic to route properly, and it must be enabled for vMotion (B) in the adapter properties. Other options are not required: active/standby mode (C) is not a requirement; VLAN ID can be any valid VLAN (D); and static IP is not necessary (E) as DHCP can be used.
Key principle: A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✓
The VMkernel adapter must be in the same subnet as the destination host.
Why this is correct
vMotion requires IP connectivity between hosts on the same subnet.
Related concept
Access ports place end devices into a single VLAN.
- ✓
The VMkernel adapter must be enabled for vMotion.
Why this is correct
vMotion must be enabled on the VMkernel adapter.
Related concept
Access ports place end devices into a single VLAN.
- ✗
The physical uplinks must be in active/standby mode.
Why it's wrong here
Teaming mode does not affect vMotion functionality.
- ✗
The port group must have VLAN ID 0.
Why it's wrong here
VLAN ID can be any value; it doesn't have to be 0.
- ✗
The port group must be configured with a static IP address.
Why it's wrong here
DHCP is possible, though not recommended.
Common exam traps
Common exam trap: an active trunk can still block the VLAN you need
A trunk being up does not prove every VLAN is crossing it. Check allowed VLAN lists, native VLAN mismatch, VLAN existence and access-port assignment.
Detailed technical explanation
How to think about this question
VLAN questions usually combine access-port and trunking clues. The key is to identify whether the issue is local to one switchport, caused by the trunk, or caused by the VLAN not existing where it needs to exist.
KKey Concepts to Remember
- Access ports place end devices into a single VLAN.
- Trunk ports carry multiple VLANs between switches.
- Allowed VLAN lists decide which VLANs can cross a trunk.
- Native VLAN mismatch can create confusing symptoms.
TExam Day Tips
- Use show vlan brief to verify access VLANs.
- Use show interfaces trunk to verify trunk state and allowed VLANs.
- Do not treat every same-VLAN issue as a routing problem.
Key takeaway
A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Real-world example
How this comes up in practice
A help-desk technician troubleshoots why a newly connected PC cannot reach shared printers on the same floor. The cable is good, the switch port is active, but the PC is in VLAN 20 and the printers are in VLAN 10. The uplink trunk only allows VLAN 10. A trunk being up does not mean every VLAN crosses it.
Visual reference
What to study next
Got this wrong? Here's your next step.
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related VCP-DCV questions on switching, trunking, and access-port configuration.
- →
Configure and Manage vSphere Networking — study guide chapter
Learn the concepts, then practise the questions
- →
Configure and Manage vSphere Networking practice questions
Targeted practice on this topic area only
- →
All VCP-DCV questions
521 questions across all exam domains
- →
VMware Certified Professional Data Center Virtualization VCP-DCV study guide
Full concept coverage aligned to exam objectives
- →
VCP-DCV practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related VCP-DCV practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
vSphere Architecture, Products and Solutions practice questions
Practise VCP-DCV questions linked to vSphere Architecture, Products and Solutions.
Configure and Manage vSphere Networking practice questions
Practise VCP-DCV questions linked to Configure and Manage vSphere Networking.
Configure and Manage vSphere Storage practice questions
Practise VCP-DCV questions linked to Configure and Manage vSphere Storage.
vSphere Lifecycle Management practice questions
Practise VCP-DCV questions linked to vSphere Lifecycle Management.
vSphere Security practice questions
Practise VCP-DCV questions linked to vSphere Security.
vSphere Performance and Scaling practice questions
Practise VCP-DCV questions linked to vSphere Performance and Scaling.
VCP-DCV fundamentals practice questions
Practise VCP-DCV questions linked to VCP-DCV fundamentals.
VCP-DCV scenario practice questions
Practise VCP-DCV questions linked to VCP-DCV scenario.
VCP-DCV troubleshooting practice questions
Practise VCP-DCV questions linked to VCP-DCV troubleshooting.
Practice this exam
Start a free VCP-DCV practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this VCP-DCV question test?
Configure and Manage vSphere Networking — This question tests Configure and Manage vSphere Networking — Access ports place end devices into a single VLAN..
What is the correct answer to this question?
The correct answer is: The VMkernel adapter must be in the same subnet as the destination host. — Options A and B are correct. The VMkernel adapter must be in the same subnet as the destination host (A) to allow vMotion traffic to route properly, and it must be enabled for vMotion (B) in the adapter properties. Other options are not required: active/standby mode (C) is not a requirement; VLAN ID can be any valid VLAN (D); and static IP is not necessary (E) as DHCP can be used.
What should I do if I get this VCP-DCV question wrong?
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related VCP-DCV questions on switching, trunking, and access-port configuration.
What is the key concept behind this question?
Access ports place end devices into a single VLAN.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Keep practising
More VCP-DCV practice questions
- A vSphere administrator is managing a cluster with vLCM and receives a notification that a new ESXi patch is available.…
- An administrator needs to apply a security patch to a vLCM-managed cluster. The patch is available as an ESXi image in t…
- An administrator sees the above JSON output from a vLCM compliance report. What should the administrator do to resolve t…
- An administrator is planning to migrate from legacy baselines to vLCM for a cluster. Which TWO statements are true about…
- A vSphere administrator is using vLCM and needs to ensure that all hosts are compliant with the desired image. Which TWO…
- Which TWO actions are recommended to secure the vCenter Server Appliance (VCSA)?
Last reviewed: Jun 24, 2026
This VCP-DCV practice question is part of Courseiva's free VMware certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the VCP-DCV exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.