Courseiva

CCNA Networking and Network Connectivity Questions

40 questions · Networking and Network Connectivity · All types, answers revealed

1
MCQeasy

A user at a small branch office reports that their laptop cannot reach any website, but the laptop can successfully ping 8.8.8.8. The technician runs ipconfig /all and sees the IPv4 address, subnet mask, and default gateway are correct, but the DNS server field is blank. Which action should the technician take first to restore web browsing?

A.Replace the Ethernet cable connecting the laptop to the wall jack.
B.Disable the Windows Defender Firewall on the laptop's active profile.
C.Configure a valid DNS server address on the laptop's network adapter.
D.Change the laptop's default gateway to the DNS server address.
AnswerC

The laptop can reach 8.8.8.8 by IP address, proving IP connectivity and routing are working. Web browsing fails because domain names cannot be resolved without a DNS server. Manually assigning a valid DNS server address, such as the local router or a public resolver, restores name resolution. This is the most direct first step for the reported symptom.

Why this answer

A successful ping to a public IP address confirms that the laptop has valid IP configuration, a working default gateway, and end-to-end connectivity. The blank DNS server field means the laptop has no way to translate domain names into IP addresses, so web browsing fails. Assigning a valid DNS server address directly addresses the missing configuration and restores name resolution.

Exam trap

The trap here is assuming that a blank DNS server field is harmless because IP connectivity works, when in fact name resolution is required for normal web browsing.

2
MCQeasy

A user on a corporate laptop can reach internal file shares by IP address but cannot reach them by hostname. The technician verifies the laptop has a valid IP address, subnet mask, and default gateway, and can ping the file server's IP address successfully. Which configuration should the technician verify next?

A.The MAC address reservation for the laptop on the DHCP server.
B.The subnet mask configured on the laptop's network adapter.
C.The default gateway address configured on the laptop's network adapter.
D.The DNS server addresses configured on the laptop's network adapter.
AnswerD

Successful ping by IP address but failure by hostname points directly to name resolution. If the laptop cannot reach a DNS server or has incorrect DNS addresses, hostname lookups fail even though IP routing works. Verifying the configured DNS server addresses on the adapter, and confirming they respond, is the logical next step before any deeper troubleshooting.

Why this answer

When IP connectivity works but hostname access fails, the fault lies in name resolution rather than routing or addressing. The laptop's configured DNS servers are the first thing to verify, since unreachable or incorrect DNS addresses cause exactly this symptom. The gateway, subnet mask, and DHCP reservation are all proven or unrelated, because successful ping by IP address demonstrates that addressing and routing are already correct.

Exam trap

The trap here is chasing Layer 3 addressing when the symptom already proves that IP connectivity works.

3
MCQmedium

A user reports that they cannot access the internet, but they can ping the default gateway of their local subnet. What is the most likely cause of the issue?

A.The NIC is disabled
B.The local IP address is incorrect
C.The router has no route to the destination
D.The switch port is blocked by PortFast
AnswerC

If the user can reach the gateway but not the internet, it indicates the traffic is reaching the router, but the router does not know how to forward it further, or the next-hop ISP connection is down, preventing internet access from being successfully established.

Why this answer

When a host can reach its default gateway but not the internet, the issue usually lies beyond the local segment. It could be an incorrect default gateway configuration on the router, a failure of the ISP connection, or a lack of NAT translation. Ping testing provides valuable diagnostic information; confirming local connectivity rules out the host's NIC or local switch port as the source of the failure.

Exam trap

Candidates often assume a local gateway ping means the internet works, ignoring upstream routing, ISP failures, or NAT misconfigurations.

4
MCQmedium

Which protocol is primarily used to resolve a known IPv4 address to an unknown MAC address on a local area network?

A.DNS
B.DHCP
C.ARP
D.ICMP
AnswerC

ARP finds the MAC address that belongs to a known IPv4 address on the local network. The host broadcasts a request asking who has that address, the owner replies directly with its MAC address, and the host caches the answer for a few minutes. For remote destinations, it ARPs for the default gateway instead. IPv6 uses Neighbor Discovery over ICMPv6 for the same job.

Why this answer

Address Resolution Protocol (ARP) is essential for local communication. Since Ethernet networks use MAC addresses to deliver frames to specific network interface cards, devices must map the target IP to a hardware address. Understanding ARP is vital for IT support, as it explains why devices cannot communicate if the resolution process fails, often due to misconfigured subnets or ARP table issues on the local gateway.

Exam trap

Students frequently confuse ARP with RARP, DNS, or DHCP, mistakenly thinking IP addresses are resolved from MAC addresses rather than the other way around.

5
MCQhard

A support technician is connecting a new Cat 6a patch cable from a wall jack to a user's desktop. The user reports intermittent disconnects and slow transfers. The technician notices the cable's RJ-45 connector has visible damage to the plastic tab that locks it into the port. Which layer of the OSI model is most directly implicated by this physical defect?

A.Layer 2, the data link layer
B.Layer 3, the network layer
C.Layer 1, the physical layer
D.Layer 4, the transport layer
AnswerC

A broken locking tab on the RJ-45 connector is a physical-layer defect because it prevents the plug from seating firmly in the jack. Poor contact causes intermittent link loss and retransmissions, which match the user's symptoms. Layer 1 governs cabling, connectors, pinouts, and signaling, so this mechanical damage is the most direct cause to investigate first.

Why this answer

The damaged locking tab is a physical-layer problem because it prevents the RJ-45 plug from maintaining solid contact with the jack. That poor connection produces intermittent link drops and slow transfers. Following a bottom-up troubleshooting approach, the technician should replace the cable first, since Layer 1 defects cannot be resolved by changing higher-layer settings.

Exam trap

The trap here is jumping to Layer 2 or Layer 3 troubleshooting for intermittent connectivity when the visible mechanical damage clearly identifies a Layer 1 fault.

6
MCQmedium

A network administrator needs to verify the connectivity between two hosts on the same VLAN. Which tool is most effective for testing if the host is reachable at the IP layer?

A.Traceroute
B.Ping
C.Telnet
D.Show ip interface
AnswerB

Ping uses ICMP to verify reachability. It is the fastest and most efficient way to determine if a target host's IP stack is active and responding. If a ping fails, it is a clear indicator that the network layer path is blocked or the host is down.

Why this answer

The 'ping' command is the most widely used tool to test basic end-to-end connectivity between two hosts. By sending ICMP Echo Request packets and waiting for an Echo Reply, an administrator can confirm that the network path is functional, that the host is configured correctly, and that no firewall or security policy is actively dropping the traffic at the target.

Exam trap

Candidates often select complex protocol analyzers or traceroute when a simple ICMP echo request tool is specifically requested for basic IP layer reachability.

7
Multi-Selectmedium

A technician is troubleshooting a workstation that cannot access network resources. The workstation is connected to a Cisco switch port that is configured for VLAN 10. The technician runs ipconfig and sees an IPv4 address of 169.254.10.5 with a subnet mask of 255.255.0.0. Which two statements describe the likely cause of this address? (Choose two.)

Select 2 answers
A.The DHCP server is unreachable from the workstation's VLAN.
B.The switch port is administratively shut down.
C.The workstation did not receive a response from a DHCP server.
D.The workstation is configured with a static IP address in the APIPA range.
E.The workstation's NIC driver is corrupted.
AnswersA, C

If the DHCP server is on a different VLAN and the DHCP relay agent is not configured on the router or switch, DHCP broadcasts will not reach the server. The workstation then falls back to APIPA. This is a common cause of APIPA addresses in VLAN environments. Ensuring the relay agent is correctly pointing to the DHCP server resolves the issue.

Why this answer

An IPv4 address in the 169.254.0.0/16 range is an APIPA address assigned by Windows when no DHCP server responds. This can occur if the DHCP server is down or unreachable, or if the DHCP relay agent is missing or misconfigured for the workstation's VLAN. The technician should verify DHCP server availability and relay configuration on the router or Layer 3 switch.

Exam trap

The trap here is assuming that an APIPA address means the NIC is faulty, when it actually indicates a DHCP communication failure while the NIC is working.

8
Multi-Selectmedium

A small office is deploying a wireless network for employees and guests. The IT support technician must choose security settings that protect employee traffic while meeting these requirements: employee credentials must not be sent in cleartext over the air, and each employee must authenticate with unique credentials rather than a shared key. Which two wireless security configurations meet these requirements? (Choose two.)

Select 2 answers
A.WEP with a 128-bit key and MAC address filtering
B.WPA2-Personal with a strong pre-shared key rotated monthly
C.Open authentication with a captive portal collecting usernames
D.WPA3-Enterprise with 802.1X authentication against a RADIUS server
E.WPA2-Enterprise with 802.1X authentication against a RADIUS server
AnswersD, E

WPA3-Enterprise also relies on 802.1X with a RADIUS server, giving each employee distinct credentials. WPA3 additionally strengthens the handshake and management-frame protection compared with WPA2. This configuration meets the requirement for unique identities and protects credentials in transit, making it a valid and more modern alternative to WPA2-Enterprise for the employee network.

Why this answer

Both WPA2-Enterprise and WPA3-Enterprise use 802.1X with a RADIUS server, which authenticates each employee individually and protects the credential exchange. Personal and open models rely on shared or absent secrets, which fail the unique-credential and confidentiality requirements. The enterprise variants are the appropriate choices for the employee wireless network.

Exam trap

The trap here is treating a strong or frequently rotated pre-shared key as equivalent to per-user authentication, when a shared key still cannot identify individual employees.

9
Multi-Selecthard

Which TWO of the following are valid methods to secure a Cisco device's management access? (Choose two.)

Select 2 answers
A.Use Telnet for remote access
B.Implement SSH
C.Enable password encryption
D.Allow all incoming SNMP traffic
E.Disable the console port
AnswersB, C

SSH (Secure Shell) provides encrypted remote access to a device's CLI. By encrypting the entire management session, it protects against credential sniffing and man-in-the-middle attacks, making it the industry-standard method for secure remote management of Cisco network devices in any production environment.

Why this answer

Securing management access is vital to prevent unauthorized changes. SSH is the standard, encrypted replacement for Telnet, which transmits credentials in cleartext. Additionally, implementing strong local passwords and disabling unused services like HTTP or SNMP further hardens the device.

These measures collectively ensure that only authorized personnel can access the device's configuration, protecting the network infrastructure from exploitation.

Exam trap

Candidates often select Telnet as a valid security method, forgetting that Telnet sends all credentials in cleartext, which makes it inherently insecure for management access in modern networks.

10
MCQmedium

Which protocol is used to resolve a known IPv4 address to a physical MAC address on a local Ethernet segment?

A.DHCP
B.DNS
C.ARP
D.ICMP
AnswerC

ARP is the protocol specifically designed to map a Layer 3 IP address to a Layer 2 MAC address. When a sender knows the destination IP but needs the hardware address to encapsulate the packet into a frame, it sends an ARP request to discover the mapping.

Why this answer

The Address Resolution Protocol (ARP) is used at the Data Link layer to map a destination IP address to the corresponding hardware MAC address. This mapping is necessary because Ethernet switches and NICs operate on MAC addresses, not IP addresses. When a host needs to communicate with another device, it broadcasts an ARP request to learn the target's MAC address to build an Ethernet frame.

Exam trap

Candidates frequently confuse ARP with RARP or DNS, failing to understand that ARP is specifically for mapping Layer 3 IP addresses to Layer 2 physical hardware addresses.

11
MCQmedium

A technician is using the network scanner in a laptop's operating system to examine a colleague's workstation that is suspected of running an unauthorized service. The scan reports that TCP port 3389 on the workstation is open and accepting connections. Which service should the technician expect to be running on that port?

A.Secure Shell (SSH)
B.Remote Desktop Protocol (RDP)
C.Server Message Block (SMB)
D.Hypertext Transfer Protocol Secure (HTTPS)
AnswerB

RDP uses TCP port 3389 by default, so an open 3389 on a Windows workstation strongly indicates the Remote Desktop service is enabled and listening. This matches the scenario because the technician is investigating an unexpected listening service on a user workstation, and RDP is the standard Microsoft remote graphical access service that would accept connections on that port.

Why this answer

TCP port 3389 is the default listener for Remote Desktop Protocol on Windows systems, so an open 3389 indicates the Remote Desktop service is enabled. The technician should treat this as a potential unauthorized remote-access exposure. The other listed services use different well-known ports, so they do not match the scan result.

Exam trap

The trap here is assuming any open high port is a web or file-sharing service rather than matching the port number to its registered default application.

12
MCQmedium

A technician is configuring a new Cisco switch for a small office. The office uses a single VLAN for all devices. The technician wants to assign an IP address to the switch's management interface so it can be accessed remotely via SSH. Which command must be entered in global configuration mode to create the management interface?

A.interface gigabitethernet 0/1
B.interface fastethernet 0/1
C.interface vlan 1
D.ip default-gateway 192.168.1.1
AnswerC

On a Cisco switch, the management IP address is assigned to a switched virtual interface (SVI), typically interface VLAN 1 by default. Entering interface vlan 1 in global configuration mode creates or enters the SVI, where an IP address and subnet mask can be configured. This allows remote management access. VLAN 1 is the default management VLAN, though best practice is to change it to a dedicated VLAN.

Why this answer

To enable remote management on a Cisco switch, a technician must assign an IP address to a switched virtual interface (SVI). The default SVI is interface VLAN 1, created by entering interface vlan 1 in global configuration mode. After assigning an IP address and bringing up the interface with no shutdown, the switch can be accessed via SSH.

Physical ports cannot be assigned IP addresses for management.

Exam trap

The trap here is assuming that a physical switch port can be assigned an IP address for management, when in fact only a switched virtual interface can hold the management IP.

13
MCQhard

Refer to the exhibit. Router R1 lacks a default gateway and cannot reach external subnets. Which static route configuration correctly establishes a default route pointing to next-hop IP address 192.168.1.254?

A.ip route 192.168.1.254 255.255.255.255 0.0.0.0
B.ip route 0.0.0.0 0.0.0.0 192.168.1.254
C.ip route 255.255.255.255 255.255.255.255 GigabitEthernet0/0
D.ip route 192.168.1.0 0.0.0.255 192.168.1.254
AnswerB

The command ip route 0.0.0.0 0.0.0.0 192.168.1.254 creates a gateway of last resort pointing to the next-hop IP 192.168.1.254. Any packet destined for an unknown network matches this catch-all static route and forwards toward the router at that IP.

Why this answer

A default route uses a destination of 0.0.0.0 and a subnet mask of 0.0.0.0 to match any traffic lacking a specific route entry. Configuring this floating path with a valid next-hop IP address allows the router to forward internet or inter-domain traffic successfully.

Exam trap

Test-takers frequently mistake the subnet mask for a host IP or forget that a default route requires all zeros for both the network address and the subnet mask.

14
MCQhard

A technician is asked to segment a network so that the finance department's traffic is isolated from the guest network at Layer 2. The requirement is that broadcast traffic from the guest network must not reach finance devices. Which technology should the technician implement to meet this requirement?

A.Virtual LANs (VLANs)
B.Domain Name System (DNS) zones
C.Dynamic Host Configuration Protocol (DHCP) scopes
D.Network Address Translation (NAT)
AnswerA

VLANs logically separate a switch into distinct broadcast domains, so broadcast traffic in the guest VLAN is not flooded to finance ports. This directly satisfies the Layer 2 isolation requirement. Inter-VLAN communication, if needed, can then be controlled through a router or Layer 3 switch with access policies, giving the technician both separation and manageable connectivity.

Why this answer

VLANs divide a physical switch into separate logical broadcast domains, which prevents guest broadcast traffic from reaching finance devices. NAT, DHCP scopes, and DNS zones operate at other layers or serve other purposes and cannot isolate Layer 2 broadcasts. Implementing VLANs, with routing and filtering between them as needed, meets the segmentation requirement.

Exam trap

The trap here is confusing logical address management, such as separate DHCP scopes, with true Layer 2 broadcast-domain separation, which only VLANs provide.

15
MCQeasy

A user's desktop can reach devices on its own subnet but cannot reach any host on a remote network. The technician runs ipconfig and sees that the IPv4 address, subnet mask, and DNS server are all correct, but the default gateway field is blank. Which action should the technician take to resolve the problem?

A.Configure a valid default gateway address on the workstation.
B.Disable the firewall on the workstation's network adapter.
C.Change the workstation's subnet mask to match the remote network.
D.Replace the DNS server entry with the router's address.
AnswerA

A blank default gateway means the host has no next-hop router for destinations outside its local subnet, so remote traffic is dropped. Assigning the correct gateway address restores the path off the local network. The other settings are already correct, so the missing gateway is the specific fault that matches the symptom of local-only connectivity.

Why this answer

The default gateway is the router address a host uses to reach destinations outside its own subnet. With that field blank, the workstation can only communicate locally, which matches the reported symptom. Re-entering the correct gateway address restores off-subnet routing, while the other suggested changes do not supply a next-hop router.

Exam trap

The trap here is blaming DNS or the firewall for a connectivity failure when the symptom of local-only reachability points directly at a missing default gateway.

16
MCQmedium

A network technician is configuring a Cisco Catalyst switch for a small office. The company uses a single VLAN (VLAN 1) for all devices. The technician wants to allow remote management of the switch from a PC on the same subnet. Which IP configuration must be applied to the switch to enable this access?

A.Assign an IP address to the switch's management interface, such as VLAN 1.
B.Create a loopback interface and assign an IP address from the management subnet.
C.Configure a default gateway on each connected PC pointing to the switch's console port IP address.
D.Enable DHCP snooping on the switch and assign an IP from the DHCP pool to the switch itself.
AnswerA

Assigning an IP address to a management interface (typically VLAN 1) allows the switch to be reached remotely for management. The switch uses this IP for Telnet, SSH, SNMP, and HTTP access. Without it, the switch is only manageable via console. This is the correct method for enabling in-band management on a Cisco switch.

Why this answer

To manage a Cisco switch remotely over the network, an IP address must be assigned to a switch virtual interface (SVI), commonly VLAN 1. This allows protocols like SSH, Telnet, and SNMP to reach the switch. The other options either misunderstand the console port, confuse security features with IP assignment, or suggest an uncommon practice for switches.

Exam trap

The trap here is confusing the console port with a network interface; the console port is for local access and does not have an IP address.

17
MCQmedium

A technician is configuring a Cisco IOS router that connects a small office to the internet. The ISP has assigned a single public IPv4 address on the WAN interface, and the router must allow the office's internal 192.168.10.0/24 hosts to access web servers on the internet. Which feature should the technician configure on the router to accomplish this?

A.Dynamic NAT with a pool containing the single WAN interface address
B.Static NAT that maps each internal host to a unique public address
C.A static default route pointing to the ISP next-hop address
D.PAT using the overload keyword in the ip nat inside source command
AnswerD

Port Address Translation with the overload keyword maps many internal private addresses to the single public IPv4 address by translating source ports, so all hosts share that one address. This is exactly the scenario: one ISP-assigned public address and a full private subnet needing outbound internet access, typically combined with ip nat inside and ip nat outside on the correct interfaces.

Why this answer

Because the ISP provides only one public IPv4 address, the router must let many private hosts share it. Port Address Translation with the overload keyword translates both the source address and source port, allowing concurrent sessions from the entire 192.168.10.0/24 subnet. Applying ip nat inside and ip nat outside to the correct interfaces completes the configuration.

Exam trap

The trap here is assuming that any form of NAT conserves a single public address, when only overload-style translation supports many-to-one address sharing.

18
MCQmedium

An IT support technician needs to verify whether a remote server is actively listening on TCP port 443 before troubleshooting an HTTPS connectivity issue. Which command-line utility provides the most direct test of this specific TCP port state from a client machine?

A.ping 192.168.1.50
B.traceroute 192.168.1.50
C.telnet 192.168.1.50 443
D.nslookup 192.168.1.50
AnswerC

The Telnet utility can establish a raw TCP connection to any specified IP address and port number. A successful connection screen confirms that port 443 is open and responsive, while a timeout indicates a firewall block or stopped service.

Why this answer

Testing TCP port availability is crucial for isolating application accessibility from broader network routing issues. Tools like Telnet or Netcat allow technicians to verify if a server accepts connections on a specific port, bypassing browser-level errors and identifying firewall blocks.

Exam trap

Candidates often confuse application-layer testing tools like ping with port-testing utilities, or incorrectly format the telnet command syntax by placing the port number before the IP address.

19
MCQeasy

Which layer of the OSI model is responsible for logical addressing and routing of packets between different networks?

A.Physical Layer
B.Data Link Layer
C.Network Layer
D.Transport Layer
AnswerC

The Network layer provides logical addressing and routing services. It determines the best path for data to travel from source to destination across multiple networks using routers or Layer 3 switches, making it the primary layer for interconnecting disparate subnets and global network communication.

Why this answer

The Network layer (Layer 3) handles the logical addressing (IP addresses) and path determination required to route data packets across diverse networks. Mastery of the OSI model is essential for troubleshooting because it allows technicians to systematically isolate where in the communication stack a failure is occurring, whether it be physical cabling, switching, or routing issues between endpoints.

Exam trap

Candidates frequently confuse Layer 3 Network layer functions like logical addressing with Layer 2 data link physical addressing or Layer 4 end-to-end reliability.

20
MCQmedium

A network administrator needs to connect two switches using a link that allows multiple VLANs to traverse the cable. Which configuration step is mandatory for this link?

A.Configure the ports as access ports using the switchport mode access command.
B.Configure the ports as trunk ports using the switchport mode trunk command.
C.Enable port security on the links to restrict the number of MAC addresses.
D.Assign the ports to the same native VLAN without using the trunking protocol.
AnswerB

Setting a port to trunk mode allows it to carry traffic for multiple VLANs by tagging frames with a VLAN ID. This is the standard method for interconnecting switches, ensuring that all VLANs defined in the network can communicate across the enterprise backbone without requiring dedicated physical links.

Why this answer

To allow traffic from multiple VLANs to traverse a single physical link between switches, the ports must be configured as trunks using a protocol like IEEE 802.1Q. This process adds a tag to the Ethernet frame, identifying the source VLAN. Understanding trunking is critical for scalable network design, as it enables logical segmentation of traffic across physical infrastructure, ensuring that broadcasts are contained within their respective VLANs while maintaining connectivity between switches.

Exam trap

Candidates often forget to change the default access port mode to trunk mode, resulting in traffic from only a single VLAN being permitted across the link.

21
MCQhard

A network administrator is configuring a Cisco wireless LAN controller (WLC) for a small office. The office has a single VLAN for both management and client traffic. The administrator wants to ensure that wireless clients receive IP addresses from the same subnet as the wired clients. Which interface type on the WLC should be configured to map to this VLAN?

A.Service-port interface
B.Dynamic interface
C.Management interface
D.Virtual interface
AnswerB

A dynamic interface on a Cisco WLC maps a wireless LAN (WLAN) to a specific VLAN. By configuring a dynamic interface tied to the office VLAN, wireless clients receive IP addresses from the same subnet as wired clients. This is the standard design for integrating wireless and wired traffic in a single VLAN environment.

Why this answer

On a Cisco WLC, dynamic interfaces are used to map WLANs to VLANs. To have wireless clients receive IP addresses from the same subnet as wired clients, the administrator must create a dynamic interface associated with the office VLAN and assign that interface to the WLAN. The management, virtual, and service-port interfaces serve other purposes and do not carry client data traffic.

Exam trap

The trap here is confusing the management interface, which is for administering the WLC, with the dynamic interface that actually carries client traffic and maps to a VLAN.

22
MCQhard

Refer to the exhibit. A router is unable to reach any external networks. Based on the output, what is the most likely configuration error?

A.The interfaces are down
B.Missing default route
C.IP address conflict
D.Routing protocol failure
AnswerB

The output explicitly states that the 'Gateway of last resort is not set.' This confirms that no default route (0.0.0.0/0) has been configured. Without a gateway of last resort, the router cannot forward traffic destined for any network not explicitly defined in its routing table.

Why this answer

The output of 'show ip route' reveals that the 'Gateway of last resort' is not set. This means the router has no default route defined to forward packets destined for networks not present in the routing table. Without a default route, the router will drop traffic destined for the internet or external segments, as it does not know where to forward those unknown packets.

Exam trap

Candidates often look for complex routing protocol issues (OSPF/EIGRP) when the output clearly shows the absence of a 'Gateway of last resort', indicating a simple missing static route.

23
MCQeasy

Which OSI layer is primarily responsible for end-to-end communication, flow control, and error correction of data segments?

A.Data Link Layer
B.Network Layer
C.Transport Layer
D.Session Layer
AnswerC

The Transport Layer (Layer 4) manages the end-to-end communication stream. It breaks data into segments, performs flow control to prevent congestion, and uses sequence numbers and acknowledgments to ensure that segments are received correctly and in the proper order by the receiving host application.

Why this answer

The Transport Layer (Layer 4) is responsible for end-to-end communication and ensuring data integrity. It handles multiplexing, segmentation, and reassembly of data. Protocols like TCP provide reliable, connection-oriented service with flow control and error recovery, while UDP provides connectionless service.

Understanding this layer is fundamental for troubleshooting application-level connectivity and data transmission issues across a network infrastructure.

Exam trap

Candidates often confuse the Transport Layer with the Network Layer, mixing up end-to-end reliability and flow control with packet routing.

24
Multi-Selectmedium

A technician is troubleshooting a workstation that cannot reach any device beyond its own subnet. The workstation has a valid IP address, subnet mask, and DNS server. The technician suspects a Layer 2 or Layer 3 configuration issue. Which two items should the technician verify to confirm the workstation can communicate off-subnet? (Choose two.)

Select 2 answers
A.The IP address is in the same subnet as the DNS server.
B.The ARP cache contains an entry mapping the default gateway IP to its MAC address.
C.The switchport mode is set to trunk on the workstation's access port.
D.The DNS suffix search list is configured with the correct domain name.
E.The default gateway address is on the same subnet as the workstation and matches the router interface.
AnswersB, E

A successful ARP entry for the gateway confirms Layer 2 reachability to the router interface. If the cache lacks the gateway mapping, the host cannot build the frame needed to send packets off-net. Checking the ARP cache verifies that address resolution for the gateway is working.

Why this answer

Off-subnet communication depends on the host having a correct default gateway on its own subnet and being able to resolve that gateway's MAC address through ARP. Verifying the gateway address and the ARP cache entry confirms both the Layer 3 configuration and Layer 2 reachability needed to forward traffic to the router.

Exam trap

The trap here is focusing on DNS settings when the symptom is a total inability to reach any remote IP address, which points to gateway or ARP problems instead.

25
Multi-Selecthard

A network administrator troubleshoots a newly installed unmanaged gigabit switch connecting multiple workstations. Which TWO symptoms most strongly indicate a physical layer cabling issue rather than a higher-layer configuration problem? (Choose two)

Select 2 answers
A.The switch port LED remains completely unlit despite the workstation being powered on.
B.Dynamic Host Configuration Protocol requests time out repeatedly.
C.Interface counters display a high volume of cyclic redundancy check errors and runts.
D.Default gateway pings fail while local subnet communication succeeds.
E.Secure Shell sessions disconnect randomly due to TCP window exhaustion.
AnswersA, C

An unlit link LED indicates an absence of physical layer electrical or optical signal transmission between the network interface card and the switch port. This points directly to broken cabling, improper termination, or an unpowered device.

Why this answer

Physical layer issues often manifest as erratic link states, high frame error rates, or complete link failure due to cable damage or attenuation. Recognizing these physical symptoms allows support technicians to quickly replace faulty patch cables without wasting time troubleshooting router configurations or software protocols.

Exam trap

Candidates frequently mistake high error rates or unlit link lights for logical configuration errors like mismatched IP addresses rather than hardware physical failures.

26
MCQeasy

What is the function of a default gateway in an IPv4 network?

A.To resolve hostnames
B.To act as an exit point for external traffic
C.To assign IP addresses
D.To switch frames between ports
AnswerB

The default gateway is the device responsible for routing traffic that is destined for networks beyond the host's local subnet. By providing the host with a destination for non-local traffic, the gateway ensures that packets can leave the local broadcast domain successfully.

Why this answer

A default gateway serves as the exit point for traffic that is destined for a network outside of the local segment. When a host wants to send data to an IP that is not on its local subnet, it directs that traffic to the default gateway (usually a router), which then decides how to forward the packet based on its own routing table to reach the destination.

Exam trap

Candidates often think the default gateway is for local communication, failing to realize it is only utilized when the destination IP address exists outside the local subnet.

27
MCQhard

A technician notices that a workstation connected to a Cisco switch port shows a link light but cannot reach any other device. The switch output shows the port in the err-disabled state with the reason psecure-violation. Which action should the technician take to restore connectivity while keeping the security feature active?

A.Enable errdisable recovery with an interval so the port re-enables automatically.
B.Remove the port security configuration from the interface and re-enable the port.
C.Shut down and re-enable the interface after removing the offending MAC address or device.
D.Configure the interface as a trunk port so the violation no longer applies.
AnswerC

A psecure-violation err-disabled state occurs when an unauthorized MAC address appears on a port with port security enabled. Removing the offending device or clearing the learned address and then cycling the interface with shutdown and no shutdown restores service while port security remains configured and enforced. This satisfies both restoring connectivity and keeping the security feature active.

Why this answer

The err-disabled reason psecure-violation means port security detected a MAC address beyond the allowed maximum or an address not in the secure table. The correct recovery is to eliminate the offending device or address and then re-enable the interface with shutdown followed by no shutdown. This clears the violation while leaving port security configured, so the protection remains in force for future unauthorized connections.

Exam trap

The trap here is reaching for errdisable recovery or removing security instead of correcting the violation cause.

28
Multi-Selectmedium

Which TWO of the following statements correctly describe the function of a default gateway in a local area network?

Select 2 answers
A.It is the IP address of the local switch used for internal VLAN communication.
B.It allows devices to communicate with hosts on different subnets.
C.It provides the IP address for all devices within the same broadcast domain.
D.It acts as the exit point for traffic destined for remote networks.
E.It is responsible for translating private IP addresses to public ones.
AnswersB, D

When a host determines that a destination IP address is outside its own subnet, it encapsulates the frame with the MAC address of the default gateway. This enables the router to receive the packet and forward it toward the correct network destination across the internetwork.

Why this answer

A default gateway is a crucial component that enables devices to communicate outside of their local subnet. It serves as the path for traffic destined for remote networks by forwarding packets to a router. Understanding the role of the gateway is fundamental for network support, as misconfiguration is one of the most common reasons for end-user connectivity issues when accessing external resources or the internet.

Exam trap

Candidates often assume the default gateway handles local traffic between devices on the same subnet, forgetting that local communication happens entirely via Layer 2 MAC addresses.

29
MCQmedium

Which command-line interface (CLI) mode must a technician enter to perform configuration changes on a Cisco device?

A.User EXEC mode
B.Privileged EXEC mode
C.Global configuration mode
D.Interface configuration mode
AnswerC

Global configuration mode is the specific mode used to make changes that affect the entire device, such as hostname, interface settings, and routing configurations. Accessing this mode is the standard procedure for an administrator to modify and save the device's configuration for production use.

Why this answer

Global configuration mode is required to change the device's running configuration. A technician must first enter privileged EXEC mode using 'enable' and then issue the 'configure terminal' command. This security design ensures that only authorized users can alter critical network settings, preventing accidental or malicious changes to the device's operational behavior or security policies.

Exam trap

Candidates often confuse user EXEC mode or privileged EXEC mode with global configuration mode, failing to include the crucial 'configure terminal' command step.

30
MCQmedium

Refer to the exhibit. An administrator is troubleshooting a link between two switches. The status shows 'up' but the protocol is 'down'. What is the most likely cause?

A.The cable is unplugged
B.Layer 2 configuration mismatch
C.The port is administratively shut down
D.The IP address is not configured
AnswerB

The up/down state indicates a Layer 2 protocol failure. Common causes include mismatched encapsulation types on trunk ports or native VLAN mismatches, which prevent the switches from correctly interpreting the frames being sent across the physical link, keeping the line protocol in a down state.

Why this answer

The status 'up/down' on an interface usually indicates a Layer 1 connection exists but a Layer 2 failure prevents the line protocol from initializing. In a switch-to-switch scenario, this is frequently caused by a duplex mismatch, a native VLAN mismatch, or incompatible encapsulation protocols. Checking the logs and interface statistics will help pinpoint the specific frame-level error occurring on the link.

Exam trap

Candidates tend to focus on physical Layer 1 issues when seeing 'up/down', overlooking that the protocol mismatch is a logical Layer 2 configuration error, such as duplex or native VLAN mismatch.

31
MCQmedium

A network administrator configures inter-VLAN routing using a single physical router interface connected to an enterprise switch configured with IEEE 802.1Q trunking. What is the standard Cisco term for this specific routing architecture?

A.Multilayer switching
B.Router-on-a-stick
C.Port security encapsulation
D.Dynamic Trunking Protocol negotiation
AnswerB

A single physical router interface is subdivided into 802.1Q subinterfaces, each mapped to a VLAN and acting as that VLAN's default gateway. Traffic between VLANs traverses the one trunk link, hence the standard Cisco term Router-on-a-stick.

Why this answer

Router-on-a-stick architecture uses subinterfaces on a single physical router port to route traffic between multiple VLANs over a single trunk link. This cost-effective design eliminates the need for dedicated physical router interfaces for every individual VLAN in smaller enterprise deployments.

Exam trap

Test-takers often confuse 'Router-on-a-stick' with standard trunking or multi-interface routing, missing the specific architecture where a single physical interface utilizes subinterfaces for VLANs.

32
MCQmedium

Which command is used to verify the current VLAN configuration, status, and port membership on a Cisco Catalyst switch?

A.show ip interface brief
B.show vlan brief
C.show running-config
D.show mac-address-table
AnswerB

This command provides a concise table of all configured VLANs, their operational status, and a list of the switch ports assigned to each. It is the primary command for verifying layer 2 segmentation and ensuring that devices are logically separated or grouped as intended by the administrator.

Why this answer

The 'show vlan brief' command is the standard method for quickly checking which VLANs are active on a switch and which ports are assigned to them. This command is essential for troubleshooting connectivity issues where a device might be placed in the wrong VLAN or where a VLAN has not been created in the database, preventing it from passing traffic as expected.

Exam trap

Candidates often choose overly verbose commands like 'show running-config' or incorrect syntax like 'show vlan status' instead of the dedicated verification command.

33
Multi-Selectmedium

Which THREE of the following are primary functions of a router in a modern enterprise network? (Choose three.)

Select 3 answers
A.Path determination
B.Logical addressing
C.Switching frames
D.Network segmentation
E.MAC address learning
AnswersA, B, D

Routers examine the destination IP address of incoming packets and consult their routing table to determine the best path to forward the traffic toward the destination network, which is the primary function of Layer 3 devices in any network architecture.

Why this answer

Routers act as the central point for inter-VLAN routing, WAN connectivity, and packet path determination based on destination IP addresses. They maintain routing tables to forward packets across different subnets. Additionally, they provide security functions like ACLs and network address translation, which are essential for protecting internal networks from external threats while allowing legitimate traffic to reach the internet or other corporate sites.

Exam trap

Candidates often select 'switching' as a router function, failing to realize that while routers can perform some switching tasks, their primary role is path determination and logical addressing across networks.

34
MCQmedium

Refer to the exhibit. A technician is troubleshooting connectivity for a device connected to FastEthernet0/2. Based on the output, what is the most likely cause of the issue?

A.There is a Layer 3 IP address conflict on the interface.
B.The interface is administratively shut down.
C.There is a physical layer issue such as a disconnected cable.
D.The VLAN associated with the interface is not created.
AnswerC

The 'down/down' status means the interface has not detected a link pulse or carrier signal from the connected device. This commonly occurs due to a damaged Ethernet cable, a loose connection, or a complete failure of the remote device's port, requiring physical inspection of the cabling.

Why this answer

The output indicates that FastEthernet0/2 is in a 'down/down' state. This status usually points to a physical layer issue, such as a disconnected cable, a faulty transceiver, or a mismatch in speed/duplex settings. Understanding how to interpret interface status is essential for IT support, as it allows technicians to quickly distinguish between layer 1 physical connectivity problems and layer 2/3 logical configuration errors during incident resolution.

Exam trap

Candidates often assume a 'down/down' status implies a configuration error or VLAN mismatch. However, in physical layer troubleshooting, 'down/down' almost always points to a disconnected cable or a faulty hardware component.

35
MCQmedium

A network administrator needs to connect a workstation to a switch port. The link must be configured to prevent loops while ensuring high availability. Which technology should be implemented on the switch port to immediately transition the port to the forwarding state upon connection?

A.BPDU Guard
B.Root Guard
C.PortFast
D.EtherChannel
AnswerC

PortFast allows an access port to immediately move from the blocking state directly to the forwarding state. This prevents DHCP timeouts that occur when switches take too long to transition ports during the listening and learning phases of the Spanning Tree Protocol, ensuring quick host connectivity.

Why this answer

PortFast is a Cisco feature that allows a switch port to transition immediately to the forwarding state, bypassing the typical listening and learning states. This is crucial for end-user devices like workstations to obtain DHCP addresses quickly without waiting for STP convergence. It does not disable STP but optimizes the port specifically for edge devices, reducing the time required for network connectivity upon initialization.

Exam trap

Candidates often mistake PortFast for a security feature or a way to disable Spanning Tree entirely, missing that it is specifically designed to accelerate endpoint connectivity for DHCP requests.

36
MCQmedium

A technician is connecting a new Cisco access point to a switch port in an office. The access point must receive its management IP address automatically from the DHCP server and must be placed in the wireless management VLAN. The switch port currently has no special configuration. Which switch port setting should the technician apply?

A.Configure the port as an access port assigned to the wireless management VLAN.
B.Configure the port as a trunk carrying the wireless management VLAN and the native VLAN.
C.Configure the port as a routed port with an IP address in the wireless management subnet.
D.Configure the port with PortFast and BPDU guard enabled only.
AnswerA

An access port places the connected device into one VLAN and forwards untagged frames, which is exactly what an access point needs when it obtains a management address from DHCP in the wireless management VLAN. The access point sends a DHCP request that the switch forwards in that VLAN, and the DHCP server replies with an address from the correct scope, satisfying both requirements.

Why this answer

An access point that needs a management address from a specific DHCP scope must be placed into the corresponding VLAN. Configuring the switch port as an access port in the wireless management VLAN forwards the access point's DHCP request into that broadcast domain, so the server assigns an address from the correct scope. Trunking, spanning tree features, and routed ports do not provide that single-VLAN membership.

Exam trap

The trap here is assuming any port connected to an access point must be a trunk.

37
MCQhard

Refer to the exhibit. A technician notices that traffic cannot traverse GigabitEthernet0/1 on router R1. Based on the provided CLI output, what action must the technician perform to bring the interface operational?

A.Execute the clear ip route command to flush invalid routing table entries.
B.Enter interface configuration mode for GigabitEthernet0/1 and issue the no shutdown command.
C.Replace the Ethernet patch cable connected to GigabitEthernet0/1 due to suspected hardware damage.
D.Modify the IP address on GigabitEthernet0/1 to match the subnet of GigabitEthernet0/0.
AnswerB

The CLI output shows GigabitEthernet0/1 in a shutdown state, which administratively disables the interface regardless of cabling or configuration. Entering interface configuration mode and issuing no shutdown clears that administrative down state, restoring the interface to operational status so traffic can traverse it.

Why this answer

The CLI output displays the status of GigabitEthernet0/1 as administratively down, which means an administrator manually issued a shutdown command. To enable the interface, the technician must enter interface configuration mode and execute the no shutdown command, allowing traffic processing.

Exam trap

Many candidates confuse 'administratively down' with 'down/down', incorrectly assuming a cable fault or transceiver issue, and waste time suggesting hardware replacement instead of simple interface configuration.

38
Multi-Selectmedium

When configuring a Cisco router interface, which THREE parameters are required for the interface to become 'up/up' and pass traffic? (Choose three.)

Select 3 answers
A.IP address
B.No shutdown
C.Routing protocol
D.Subnet mask
E.Default gateway
AnswersA, B, D

A Layer 3 router interface requires a valid IP address and subnet mask to operate. Without these, the router cannot participate in routing functions or forward packets, and the interface will not be able to perform its primary function of moving data between networks.

Why this answer

To achieve an operational 'up/up' state, an interface must be physically connected, enabled, and have a valid IP configuration. Without a cable or power, the physical layer stays down. Without 'no shutdown', the administrative state prevents communication.

Without an IP address on a Layer 3 interface, the router cannot route traffic, and the interface remains logically incomplete, preventing successful packet forwarding.

Exam trap

Candidates often forget the 'no shutdown' command, assuming that assigning an IP address is sufficient to bring an interface to an 'up/up' state on a Cisco device.

39
MCQeasy

A user at a small branch office reports that file transfers to a server on a different subnet are extremely slow, even though the local network works fine. A technician runs the ipconfig /all command on the workstation and notices the DNS server address is 127.0.0.1. Which statement best describes the immediate problem with this configuration?

A.The default gateway is set to 127.0.0.1, which prevents traffic from leaving the local subnet.
B.The workstation is configured to use itself as the DNS server, so name resolution for remote hosts will fail.
C.The workstation cannot obtain an IP address because 127.0.0.1 is reserved and conflicts with DHCP.
D.The subnet mask is incorrect because 127.0.0.1 indicates a /8 network, causing remote subnet mismatches.
AnswerB

127.0.0.1 is the IPv4 loopback address, so the workstation points DNS queries at itself. Since no DNS service runs locally, queries for the remote server's hostname will time out, and the application may stall or fail to resolve the name before connecting, which matches the reported slowness or failure.

Why this answer

127.0.0.1 is the IPv4 loopback address, meaning the workstation is configured to send DNS queries to itself. With no local DNS service, lookups for the remote server name cannot be resolved, so file transfers may hang or fail while local IP connectivity still works. Correcting the DNS server entry restores name resolution and normal access to the remote server.

Exam trap

The trap here is assuming an unusual address in one field automatically breaks routing or DHCP, when the actual symptom points specifically to name resolution.

40
MCQmedium

A technician is testing a newly installed fiber uplink between a distribution switch and an access switch. The link status shows up/up, and the technician wants to confirm the actual achievable throughput before putting the link into production. Which tool should the technician use to measure the real bandwidth between the two Cisco switches?

A.Run the show interfaces counters errors command on both switches to calculate throughput.
B.Use the Cisco IOS Traceroute command with the numeric keyword between the two switches.
C.Use the Cisco IOS IP SLA UDP jitter operation to measure throughput between the two switches.
D.Use the iperf3 client and server on hosts at each end of the link to measure throughput.
AnswerD

iperf3 running a TCP or UDP stream between hosts on each side of the uplink generates real traffic that saturates the path, giving a measured throughput figure in Mbps or Gbps. Unlike latency probes, it pushes bulk data and reports the achieved rate, which is exactly what the technician needs to validate the fiber link before production. It works independently of switch CPU because hosts do the work.

Why this answer

Measuring real throughput requires generating traffic that saturates the path between two endpoints. iperf3 does exactly that by running a client and server on hosts connected through the uplink and reporting the achieved rate. Latency-oriented tools such as IP SLA jitter, traceroute, and interface error counters describe delay, path, or faults, but none of them produce a bandwidth measurement. Before putting the fiber link into production, the technician needs the saturated throughput figure that iperf3 provides.

Exam trap

The trap here is assuming that latency or error statistics from Cisco IOS tools equate to a bandwidth measurement.

Ready to test yourself?

Try a timed practice session using only Networking and Network Connectivity questions.