- A
SPAN can cause increased CPU utilization on the switch if many packets are mirrored.
Correct because mirroring high-bandwidth traffic can stress the switch CPU.
- B
SPAN can monitor control plane traffic such as routing protocol updates by default.
Why wrong: Incorrect because SPAN typically monitors only data plane traffic; control plane traffic is not mirrored unless using CPU SPAN or special configuration.
- C
RSPAN requires that the RSPAN VLAN be pruned from all trunks to avoid loops.
Correct because the RSPAN VLAN should be pruned from trunks where it is not needed to prevent loops and unnecessary flooding.
- D
A SPAN destination port cannot be used for normal network traffic.
Correct because the destination port is dedicated to receiving mirrored traffic and does not forward normal traffic.
- E
RSPAN can be used to monitor traffic on a Layer 3 routed interface.
Why wrong: Incorrect because RSPAN sources must be Layer 2 interfaces; Layer 3 interfaces are not supported as RSPAN sources.
Quick Answer
The correct answer is that a SPAN destination port cannot be used for normal network traffic. This is because when a port is configured as a SPAN destination, it is placed into a special monitoring mode that strips it of its normal switching functionality—it can only receive copied frames from the source ports and cannot forward or receive standard data traffic. On the ENCOR 350-401 exam, this concept tests your understanding of how SPAN and RSPAN limitations affect network design, often appearing in a "choose three" format where common traps include assuming RSPAN supports Layer 3 source interfaces directly or that SPAN can monitor control plane traffic without special configuration. Remember that SPAN impacts CPU performance, RSPAN requires a dedicated VLAN pruned across the network, and neither allows the destination port to function as a regular switchport. A useful memory tip: "Destination is dead to data"—once a port is a SPAN destination, it stops normal switching.
CCNP SPAN and RSPAN Practice Question
This 350-401 practice question tests your understanding of span and rspan. The scenario asks you to isolate a root cause — eliminate options that address a different problem before choosing. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Which three statements about SPAN and RSPAN limitations are true? (Choose three.)
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
SPAN can cause increased CPU utilization on the switch if many packets are mirrored.
SPAN and RSPAN can impact switch performance due to increased CPU/memory usage. SPAN cannot monitor control plane traffic (e.g., routing updates) unless specifically configured. RSPAN requires a dedicated VLAN that must be pruned appropriately. A SPAN destination port stops normal switching. RSPAN does not support Layer 3 routed interfaces as sources directly.
Key principle: A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✓
SPAN can cause increased CPU utilization on the switch if many packets are mirrored.
Why this is correct
Correct because mirroring high-bandwidth traffic can stress the switch CPU.
Related concept
Access ports place end devices into a single VLAN.
- ✗
SPAN can monitor control plane traffic such as routing protocol updates by default.
Why it's wrong here
Incorrect because SPAN typically monitors only data plane traffic; control plane traffic is not mirrored unless using CPU SPAN or special configuration.
- ✓
RSPAN requires that the RSPAN VLAN be pruned from all trunks to avoid loops.
- ✓
A SPAN destination port cannot be used for normal network traffic.
Why this is correct
Correct because the destination port is dedicated to receiving mirrored traffic and does not forward normal traffic.
Related concept
Access ports place end devices into a single VLAN.
- ✗
RSPAN can be used to monitor traffic on a Layer 3 routed interface.
Why it's wrong here
Incorrect because RSPAN sources must be Layer 2 interfaces; Layer 3 interfaces are not supported as RSPAN sources.
Common exam traps
Common exam trap: an active trunk can still block the VLAN you need
A trunk being up does not prove every VLAN is crossing it. Check allowed VLAN lists, native VLAN mismatch, VLAN existence and access-port assignment.
Detailed technical explanation
How to think about this question
VLAN questions usually combine access-port and trunking clues. The key is to identify whether the issue is local to one switchport, caused by the trunk, or caused by the VLAN not existing where it needs to exist.
KKey Concepts to Remember
- Access ports place end devices into a single VLAN.
- Trunk ports carry multiple VLANs between switches.
- Allowed VLAN lists decide which VLANs can cross a trunk.
- Native VLAN mismatch can create confusing symptoms.
TExam Day Tips
- Use show vlan brief to verify access VLANs.
- Use show interfaces trunk to verify trunk state and allowed VLANs.
- Do not treat every same-VLAN issue as a routing problem.
Key takeaway
A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Real-world example
How this comes up in practice
A help-desk technician troubleshoots why a newly connected PC cannot reach shared printers on the same floor. The cable is good, the switch port is active, but the PC is in VLAN 20 and the printers are in VLAN 10. The uplink trunk only allows VLAN 10. A trunk being up does not mean every VLAN crosses it.
What to study next
Got this wrong? Here's your next step.
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related 350-401 questions on switching, trunking, and access-port configuration.
- →
SPAN and RSPAN — study guide chapter
Learn the concepts, then practise the questions
- →
SPAN and RSPAN practice questions
Targeted practice on this topic area only
- →
All 350-401 questions
2,015 questions across all exam domains
- →
ENCOR 350-401 study guide
Full concept coverage aligned to exam objectives
- →
350-401 practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related 350-401 practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
Architecture practice questions
Practise 350-401 questions linked to Architecture.
Enterprise Network Design practice questions
Practise 350-401 questions linked to Enterprise Network Design.
SD-Access Architecture practice questions
Practise 350-401 questions linked to SD-Access Architecture.
SD-WAN Architecture practice questions
Practise 350-401 questions linked to SD-WAN Architecture.
QoS Architecture practice questions
Practise 350-401 questions linked to QoS Architecture.
Virtualization practice questions
Practise 350-401 questions linked to Virtualization.
Network Function Virtualization practice questions
Practise 350-401 questions linked to Network Function Virtualization.
Virtual Machines and Hypervisors practice questions
Practise 350-401 questions linked to Virtual Machines and Hypervisors.
VRF and Path Isolation practice questions
Practise 350-401 questions linked to VRF and Path Isolation.
Infrastructure practice questions
Practise 350-401 questions linked to Infrastructure.
OSPF practice questions
Practise 350-401 questions linked to OSPF.
BGP practice questions
Practise 350-401 questions linked to BGP.
Practice this exam
Start a free 350-401 practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this 350-401 question test?
SPAN and RSPAN — This question tests SPAN and RSPAN — Access ports place end devices into a single VLAN..
What is the correct answer to this question?
The correct answer is: SPAN can cause increased CPU utilization on the switch if many packets are mirrored. — SPAN and RSPAN can impact switch performance due to increased CPU/memory usage. SPAN cannot monitor control plane traffic (e.g., routing updates) unless specifically configured. RSPAN requires a dedicated VLAN that must be pruned appropriately. A SPAN destination port stops normal switching. RSPAN does not support Layer 3 routed interfaces as sources directly.
What should I do if I get this 350-401 question wrong?
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related 350-401 questions on switching, trunking, and access-port configuration.
What is the key concept behind this question?
Access ports place end devices into a single VLAN.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Last reviewed: Jun 18, 2026
This 350-401 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 350-401 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.