Courseiva
← Back to ENCOR 350-401 questions

Scenario-based practice

VLAN and Inter-VLAN Routing Scenarios

Practise 350-401 VLAN and trunking questions covering access ports, trunk ports, allowed VLAN lists, native VLAN, inter-VLAN routing, and command-output troubleshooting.

15
scenario questions
350-401
exam code
Cisco
vendor

Scenario guide

How to approach vlan and inter-vlan routing scenarios

VLAN misconfiguration is one of the top sources of connectivity failures in real networks and one of the most tested areas on the CCNA. These questions cover VLAN access ports, 802.1Q trunks, native VLANs, and router-on-a-stick or layer-3 switch inter-VLAN routing.

Quick answer

Routing questions usually test route selection (administrative distance, metric), how static routes are configured and when they are preferred over dynamic routing.

Administrative distance comparing routing sources.

Static route configuration: next-hop vs exit interface.

Default route propagation and the gateway of last resort.

Recursive routing table lookups.

Related practice questions

Related 350-401 topic practice pages

Scenario questions usually connect to one or more exam topics. Use these links to review the underlying concepts behind the scenario.

Practice set

Practice scenarios

Question 1hardmultiple choice
Open the full VLAN trunking answer →

An engineer is configuring RSPAN to monitor traffic from multiple switches in a data center. The monitoring station is connected to a central switch. The engineer has configured an RSPAN VLAN (VLAN 999) on all switches and set up the source sessions on the remote switches. However, the monitoring station receives no traffic. On the central switch, the engineer verifies that the RSPAN VLAN is active and that the destination session is configured. What is a likely missing configuration?

Question 2mediummultiple choice
Open the full VLAN trunking answer →

A network engineer runs the following command on Switch SW1:

SW1# show vlan brief

VLAN Name                             Status    Ports

---- -------------------------------- --------- ------------------------------- 1 default active Gi0/1, Gi0/2, Gi0/3 10 Sales active Gi0/4, Gi0/5 20 Engineering active Gi0/6, Gi0/7 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup

Based on this output, what can be concluded?

Question 3mediummultiple choice
Open the full VLAN trunking answer →

An engineer is troubleshooting a problem where a trunk link between two Cisco switches is not passing traffic for VLAN 10, but other VLANs are working. The trunk is configured with switchport mode trunk on both sides. The engineer checks the allowed VLAN list and sees VLAN 10 is included. The native VLAN is set to 1 on both sides. What is the most likely cause?

Question 4easymultiple choice
Open the full VLAN trunking answer →

A network administrator is configuring a new Cisco IOS switch and wants to ensure that the management VLAN is isolated from user traffic. The administrator needs to assign an IP address to VLAN 1 for management access. Which command should be used to enter the interface configuration mode for VLAN 1?

Question 5mediummultiple choice
Open the full VLAN trunking answer →

Consider this configuration:

interface Port-channel1
 switchport mode trunk
 switchport trunk native vlan 999

!

interface GigabitEthernet0/1
 switchport mode trunk
 switchport trunk native vlan 999
 channel-group 1 mode active

!

interface GigabitEthernet0/2
 switchport mode trunk
 switchport trunk native vlan 999
 channel-group 1 mode active

What is the effect of the 'switchport trunk native vlan 999' command on the EtherChannel?

Question 6easymultiple choice
Open the full VLAN trunking answer →

A network engineer runs the following command on a Cisco WLC:

WLC# show wlan summary

WLAN ID SSID Status Security Interface 1 Guest Enabled Open guest-vlan 2 Corporate Enabled WPA2 corp-vlan 3 IoT Disabled WPA2 iot-vlan 4 Management Enabled WPA2 mgmt-vlan

Based on this output, what can be concluded?

Question 7easymultiple choice
Open the full VLAN trunking answer →

A network engineer is configuring a new switch that will be used as an access layer switch. The switch connects to two distribution switches via trunk links. The engineer wants to ensure that the access switch does not become the root bridge for any VLAN. The engineer also wants to provide redundancy so that if one uplink fails, the other uplink takes over quickly. The engineer is using Rapid PVST+. What configuration should the engineer apply on the access switch?

Question 8mediummultiple choice
Open the full VLAN trunking answer →

A company has a campus network with two distribution switches (DSW1 and DSW2) connected via a Layer 2 trunk. Each distribution switch connects to two access switches. Spanning Tree Protocol (STP) is running with default settings. Recently, a network administrator added a new access switch (ASW3) and connected it to both distribution switches. After the connection, network performance degraded significantly, and users in VLAN 10 reported intermittent connectivity. The administrator checked the logs and saw multiple TCN notifications. What is the most likely cause of the issue?

Question 9mediummultiple choice
Full question →

Examine the following configuration snippet:

interface GigabitEthernet1/0/2
 switchport mode access

authentication port-control auto mab dot1x pae authenticator dot1x timeout tx-period 10

Which statement about this configuration is true?

Question 10mediummultiple choice
Open the full VLAN trunking answer →

An organization is implementing 802.1X for wireless users using Cisco ISE as the RADIUS server. The network engineer configures the wireless LAN controller (WLC) with 802.1X authentication. Users report that they can connect to the SSID but cannot access any network resources. The engineer checks the WLC and sees that users are authenticated and assigned to VLAN 100. The engineer also checks the switchport connecting the WLC and sees it is a trunk. What is the most likely issue?

Question 11mediumdrag order
Open the full VLAN trunking answer →

Drag and drop the steps of Private VLAN (PVLAN) configuration steps into the correct order, from first to last.

Drag or tap steps into the slots.

Steps
Order
1Step 1
2Step 2
3Step 3
4Step 4
5Step 5
Question 12easymultiple choice
Open the full VLAN trunking answer →

An engineer is configuring a new VLAN 100 on a switch. Which command must be used to create the VLAN?

Question 13mediummultiple choice
Open the full VLAN trunking answer →

An engineer is troubleshooting a problem where a host in VLAN 20 cannot communicate with a host in VLAN 30, even though both are connected to the same access switch. The access switch is configured with VLANs 20 and 30, and the uplink to the distribution switch is a trunk that allows both VLANs. The distribution switch has SVIs for both VLANs and IP routing is enabled. The engineer verifies that the trunk is up and both VLANs are allowed. What is the most likely cause of the communication failure?

Question 14easymultiple choice
Open the full VLAN trunking answer →

A network administrator is configuring a new VLAN 100 on a switch and wants to ensure that the VLAN is created and active. Which command is required to create a VLAN in the VLAN database?

Question 15hardmultiple choice
Open the full VLAN trunking answer →

A network engineer writes an Ansible playbook to configure a VLAN on a Cisco Nexus switch:

```yaml --- - name: Configure VLAN hosts: nxos_switches gather_facts: no tasks: - name: Create VLAN 100 cisco.nxos.nxos_vlan: vlan_id: 100 name: test_vlan state: present ```

What is a potential issue with this playbook?

These 350-401 practice questions are part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style 350-401 questions with detailed explanations, topic-based practice, mock exams, readiness tracking, and study analytics.