- A
Define the capture point specifying the interface and direction (monitor capture point command)
This is the correct sequence for using embedded packet capture on IOS-XE. You must first enter global config mode, then define the capture point with interface and direction, start the capture, stop it when enough data is collected, and finally export the capture file to a TFTP server for analysis in Wireshark.
- B
Start the capture (monitor capture point start)
This is incorrect because the capture point must be defined before starting the capture. Starting the capture without a defined capture point would fail or capture nothing.
- C
Stop the capture (monitor capture point stop)
This is incorrect because exporting the capture must occur after the capture is stopped. Exporting before starting or during capture would export an empty or incomplete file.
- D
Export the capture to a TFTP server (monitor capture point export)
This is incorrect because the capture point must be defined before starting the capture. Additionally, stopping the capture before defining the capture point is nonsensical.
CCNA Switching and Network Access Practice Question
This 200-301 practice question tests your understanding of switching and network access. This is a configuration task: choose the command set that satisfies every stated requirement. Small differences — like 'secret' vs 'password' or 'transport input ssh' vs 'all' — change whether the answer is correct. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Drag and drop the following steps into the correct order to capture and analyze traffic on IOS-XE using the embedded packet capture feature, then export the capture for analysis in Wireshark to isolate a Layer 2 or Layer 3 fault.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
Define the capture point specifying the interface and direction (monitor capture point command)
Embedded Packet Capture (EPC) on IOS-XE uses exec-mode monitor capture commands without needing global configuration mode. First, define the capture point specifying the interface and direction. Then start the capture to collect packets. Stop the capture after gathering sufficient data, and finally export the file to a TFTP server for analysis in Wireshark.
Key principle: Authentication proves identity; authorization controls what that identity can do after login. Both must work for full privileged access.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✓
Define the capture point specifying the interface and direction (monitor capture point command)
Why this is correct
This is the correct sequence for using embedded packet capture on IOS-XE. You must first enter global config mode, then define the capture point with interface and direction, start the capture, stop it when enough data is collected, and finally export the capture file to a TFTP server for analysis in Wireshark.
Related concept
Authentication checks who the user is.
- ✓
Start the capture (monitor capture point start)
Why this is correct
This is incorrect because the capture point must be defined before starting the capture. Starting the capture without a defined capture point would fail or capture nothing.
Related concept
Authentication checks who the user is.
- ✓
Stop the capture (monitor capture point stop)
Why this is correct
This is incorrect because exporting the capture must occur after the capture is stopped. Exporting before starting or during capture would export an empty or incomplete file.
Related concept
Authentication checks who the user is.
- ✓
Export the capture to a TFTP server (monitor capture point export)
Why this is correct
This is incorrect because the capture point must be defined before starting the capture. Additionally, stopping the capture before defining the capture point is nonsensical.
Related concept
Authentication checks who the user is.
Common exam traps
Common exam trap: authentication is not authorization
Logging in proves the user can authenticate. It does not automatically mean the user is allowed to enter privileged or configuration mode. Watch for AAA authorization, privilege level and command authorization details.
Detailed technical explanation
How to think about this question
This kind of question is testing the difference between identity and permission. A user may successfully log in to a router because authentication is working, but still fail to enter configuration mode because authorization is missing, misconfigured or mapped to a lower privilege level.
KKey Concepts to Remember
- Authentication checks who the user is.
- Authorization controls what the user is allowed to do after login.
- Privilege levels affect access to EXEC and configuration commands.
- AAA, TACACS+ and RADIUS can separate login success from command access.
TExam Day Tips
- Do not assume successful login means full administrative access.
- Look for words such as cannot enter configuration mode, privilege level, authorization or command access.
- Separate login problems from permission problems before choosing the answer.
Key takeaway
Authentication proves identity; authorization controls what that identity can do after login. Both must work for full privileged access.
Real-world example
How this comes up in practice
A practitioner preparing for the 200-301 exam encounters this exact type of scenario on the job. The correct answer here is not the most general option — it is the best answer for the specific constraint described. Authentication proves identity; authorization controls what that identity can do after login. Both must work for full privileged access. Real exam questions reward reading the full scenario before eliminating options, because the constraint defines which answer fits.
What to study next
Got this wrong? Here's your next step.
Review Cisco AAA concepts — authentication, authorization, and accounting. Study privilege levels (0–15), command authorization under TACACS+, and how RADIUS differs. Then practise related 200-301 questions on access control and AAA configuration.
- →
Switching and Network Access — study guide chapter
Learn the concepts, then practise the questions
- →
Switching and Network Access practice questions
Targeted practice on this topic area only
- →
All 200-301 questions
1,819 questions across all exam domains
- →
CCNA 200-301 v2 study guide
Full concept coverage aligned to exam objectives
- →
200-301 practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related 200-301 practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
Network Infrastructure and Connectivity practice questions
Practise 200-301 questions linked to Network Infrastructure and Connectivity.
Switching and Network Access practice questions
Practise 200-301 questions linked to Switching and Network Access.
IP Routing practice questions
Practise 200-301 questions linked to IP Routing.
Network Services and Security practice questions
Practise 200-301 questions linked to Network Services and Security.
AI and Network Operations practice questions
Practise 200-301 questions linked to AI and Network Operations.
CCNA subnetting practice questions
Practise IPv4 subnetting, CIDR, masks, host ranges and subnet selection.
CCNA OSPF practice questions
Practise OSPF neighbours, router IDs, metrics, areas and routing-table interpretation.
CCNA VLAN practice questions
Practise VLANs, access ports, trunks, allowed VLANs and switching scenarios.
CCNA STP practice questions
Practise spanning tree, root bridge election, port roles and STP troubleshooting.
CCNA EtherChannel practice questions
Practise LACP, PAgP, port-channel behaviour and bundle requirements.
CCNA ACL practice questions
Practise standard and extended ACLs, permit/deny logic and traffic filtering.
CCNA NAT practice questions
Practise static NAT, dynamic NAT, PAT and inside/outside address translation.
Practice this exam
Start a free 200-301 practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this 200-301 question test?
Switching and Network Access — This question tests Switching and Network Access — Authentication checks who the user is..
What is the correct answer to this question?
The correct answer is: Define the capture point specifying the interface and direction (monitor capture point command) — Embedded Packet Capture (EPC) on IOS-XE uses exec-mode monitor capture commands without needing global configuration mode. First, define the capture point specifying the interface and direction. Then start the capture to collect packets. Stop the capture after gathering sufficient data, and finally export the file to a TFTP server for analysis in Wireshark.
What should I do if I get this 200-301 question wrong?
Review Cisco AAA concepts — authentication, authorization, and accounting. Study privilege levels (0–15), command authorization under TACACS+, and how RADIUS differs. Then practise related 200-301 questions on access control and AAA configuration.
What is the key concept behind this question?
Authentication checks who the user is.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Last reviewed: Jun 6, 2026
This 200-301 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 200-301 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.