350-401 VRF and Path Isolation Practice Questions

Question 1

A network engineer is configuring MPLS L3VPN on a Cisco IOS-XE PE router. The engineer creates a VRF named CUSTOMER_A with route-target import and export 100:1. After configuring the VRF on the interface connected to the CE router, the CE router can ping the PE's VRF interface IP, but cannot reach any remote VPNv4 routes. The BGP session between PE and route reflector is up. What is the most likely cause?

Accepted Answer

The VRF is not activated under BGP using the address-family ipv4 vrf CUSTOMER_A command.. The CE router can ping the PE's VRF interface IP, confirming Layer 2 and VRF interface configuration are correct. However, the CE cannot reach remote VPNv4 routes, which indicates that the PE is not advertising or installing those routes into the VRF. The most likely cause is that the VRF CUSTOMER_A has not been activated under BGP using the 'address-family ipv4 vrf CUSTOMER_A' command, which is required to exchange IPv4 routes between the PE and CE within the VRF context and to redistribute them into MP-BGP for VPNv4 propagation.

Answer

The route-target import/export values are mismatched with the route reflector's configuration.

Answer

The CE router is not configured with a default route pointing to the PE.

Answer

The PE router needs the mpls ip command on the interface facing the CE router.

Question 2

An enterprise uses VRF-lite to isolate guest Wi-Fi traffic from corporate traffic on a Cisco Catalyst 9300 switch. The guest VRF (GUEST) is configured on VLAN 100, and the corporate VRF (CORP) on VLAN 200. Both VRFs use the same default gateway router connected via a trunk. The engineer notices that guest devices can reach the internet but cannot access the guest captive portal hosted on a server in VLAN 100. The server's IP is reachable from the switch itself. What is the issue?

Accepted Answer

The guest server is in a different VLAN than the guest wireless subnet, and inter-VLAN routing is not configured within the GUEST VRF.. The issue is that the guest captive portal server resides in VLAN 100, but the guest wireless subnet is likely in a different VLAN or subnet within the GUEST VRF. Since VRF-lite provides separate routing tables, inter-VLAN routing within the same VRF must be explicitly configured (e.g., using SVIs with 'ip routing' and proper VRF forwarding). The switch can reach the server because it is directly connected, but guest devices cannot because their traffic is not routed between the wireless subnet and the server's VLAN within the GUEST VRF.

Answer

The trunk between the switch and the router is not allowing VLAN 100.

Answer

The guest VRF is missing the route-target export command.

Answer

The captive portal server is configured with a default gateway that points to the corporate VRF.

Question 3

A service provider uses MPLS L3VPN with multiple VRFs on a Cisco ASR 1000 PE router. One customer VRF (RED) has overlapping IP addresses with another VRF (BLUE). The engineer configures route-target import/export as 100:1 for RED and 200:2 for BLUE. Both VRFs have a static default route pointing to the CE. The PE receives VPNv4 routes from the route reflector for both VRFs. However, traffic from RED to its CE is working, but traffic from BLUE to its CE is intermittently failing. What is the most likely cause?

Accepted Answer

The BLUE VRF's interface is not configured with the ip vrf forwarding BLUE command, so the interface is in the global routing table.. The correct answer is A because if the BLUE VRF's interface is missing the 'ip vrf forwarding BLUE' command, the interface remains in the global routing table. This means traffic from the BLUE VRF will be forwarded using the global routing table instead of the VRF's routing table, causing intermittent failures when the global table does not have a route to the CE or when the CE's IP overlaps with another VRF's subnet. The static default route configured in the BLUE VRF would not be used, leading to connectivity issues.

Answer

The route-target import for BLUE is 200:2, but the route reflector exports routes with a different route-target.

Answer

The PE router has too many VRFs, causing memory exhaustion.

Answer

The BLUE VRF is missing the rd command.

Question 4

A network engineer is troubleshooting a VRF-lite deployment on a Cisco Nexus 9000 switch. Two VRFs, PROD and DEV, are configured. The switch has an SVI for VLAN 10 in VRF PROD and VLAN 20 in VRF DEV. A firewall is connected to a Layer 3 port in VRF PROD for internet access. The engineer needs to allow the DEV VRF to reach the internet through the same firewall, but without using a separate physical interface. What should the engineer configure?

Accepted Answer

Configure a static route in VRF DEV pointing to the firewall's IP address in VRF PROD, and use the route-map to leak the route.. Option A is correct because VRF-lite does not support direct route leaking between VRFs without an external mechanism. By configuring a static route in VRF DEV pointing to the firewall's IP address (which resides in VRF PROD) and using a route-map to leak the route, the engineer enables inter-VRF routing. This allows DEV traffic to reach the firewall's interface in PROD without requiring a separate physical interface, as the route-map controls which prefixes are shared between VRFs.

Answer

Place the firewall interface in both VRFs using the ip vrf forwarding command on the same interface.

Answer

Create a VLAN trunk between the switch and firewall, and assign the same VLAN to both VRFs.

Answer

Use policy-based routing (PBR) in VRF DEV to forward traffic to the firewall's MAC address.

Question 5

An engineer is configuring MPLS L3VPN on a Cisco IOS-XR router. The VRF CUSTOMER_B is configured with route-target import 100:1 and export 100:1. The engineer notices that the VRF routes are not being advertised to the route reflector. The BGP session to the route reflector is established and the VPNv4 address family is activated. What is the missing configuration?

Accepted Answer

The engineer did not configure the address-family ipv4 unicast vrf CUSTOMER_B under BGP and redistribute the routes.. Option B is correct because in MPLS L3VPN on Cisco IOS-XR, simply configuring the VRF and establishing the BGP VPNv4 session is insufficient. The engineer must explicitly configure the address-family ipv4 unicast vrf CUSTOMER_B under BGP and use the redistribute command (e.g., redistribute connected or redistribute static) to inject the VRF routes into BGP for advertisement to the route reflector. Without this, the VRF routes remain in the local routing table but are never converted into VPNv4 prefixes.

Answer

The VRF is not configured with a route distinguisher.

Answer

The route-target import/export values are incorrect.

Answer

The interface in the VRF is not configured with the ipv4 address.

Question 6

A company uses VRF-lite to separate management traffic (VRF MGMT) from user traffic (VRF USER) on a Cisco Catalyst 3850 stack. The management network is 10.0.0.0/24, and the user network is 192.168.1.0/24. The engineer wants to allow SSH access from the user network to the management network for device administration. The switch has an SVI for each VRF. What is the simplest way to achieve this while maintaining VRF isolation?

Accepted Answer

Configure a static route in VRF USER pointing to the VRF MGMT's SVI IP address, and enable route leaking between the VRFs.. Option A is correct because VRF-lite inherently isolates routing tables, so to allow SSH from VRF USER to VRF MGMT while maintaining isolation, you must leak routes between the VRFs. A static route in VRF USER pointing to the VRF MGMT SVI IP address, combined with route leaking (e.g., using `route-map` and `import/export` commands), enables the necessary reachability without merging the VRFs. This is the simplest method as it avoids additional hardware or complex configurations.

Answer

Place both SVIs in the same VRF and use access-lists to restrict traffic.

Answer

Use a firewall between the VRFs to filter traffic.

Answer

Configure the switch to use the global routing table for SSH traffic only.

Question 7

A network engineer is configuring MPLS L3VPN on a Cisco IOS-XE router. The VRF CUSTOMER_C has route-target import 300:1 and export 300:1. The PE receives VPNv4 routes from the route reflector, but the CE router connected to the PE cannot ping any remote site IP addresses. The PE can ping the remote site IP addresses from the VRF. What is the most likely cause?

Accepted Answer

The CE router does not have a default route pointing to the PE's VRF interface.. The PE can ping remote site IP addresses from within the VRF, confirming that the VRF has the correct route-target import/export configuration and that VPNv4 routes are being received and installed in the VRF routing table. However, the CE router cannot ping remote sites, which indicates that the CE does not have a route pointing to the PE’s VRF interface as its next hop. Without a default route or a specific route pointing to the PE’s VRF-facing interface, the CE has no path to forward traffic to remote VPN destinations, even though the PE can reach them.

Answer

The VRF is missing the route-target export command.

Answer

The PE router is not running a routing protocol with the CE router.

Answer

The MPLS LDP is not enabled on the PE-CE link.

Question 8

An enterprise uses VRF-lite on a Cisco Catalyst 9300 to isolate a guest network (VRF GUEST) from the corporate network (VRF CORP). The guest network uses DHCP from a server in the corporate network. The engineer configures a DHCP relay on the guest SVI pointing to the corporate DHCP server. The DHCP server is in VRF CORP. The guest clients are not receiving IP addresses. What is the issue?

Accepted Answer

The DHCP server is in a different VRF, and the switch does not have a route from the GUEST VRF to the CORP VRF for the DHCP server.. The DHCP server resides in VRF CORP, but the DHCP relay agent on the guest SVI forwards the discover packet within VRF GUEST. Without a route from VRF GUEST to the DHCP server's subnet in VRF CORP, the relayed packet cannot reach the server. Inter-VRF routing (e.g., a route leak or VRF-aware service) is required for the relay to forward the packet across VRFs.

Answer

The DHCP relay agent is not configured to use the VRF GUEST; the ip helper-address command must be applied under the VRF interface, but the DHCP server is in a different VRF, requiring inter-VRF routing or the use of the ip dhcp relay information option.

Answer

The DHCP server is not configured with a scope for the guest subnet.

Answer

The guest VRF is missing the ip dhcp relay command globally.

Question 9

A service provider is migrating a customer from a global routing table to a VRF on a Cisco ASR 1000. The customer has a BGP session with the provider for internet access. After moving the customer's interface to VRF CUSTOMER_D, the BGP session goes down. The engineer verifies that the VRF is configured with the correct route-target and that the BGP neighbor is configured under address-family ipv4 vrf CUSTOMER_D. What else is missing?

Accepted Answer

The IP address on the interface was removed when the VRF was applied, and it was not reconfigured.. When a VRF is applied to an interface on a Cisco ASR 1000, the interface's IP address is removed because the VRF changes the routing context. The engineer must reconfigure the IP address under the VRF interface. Without the IP address, the BGP session cannot establish a TCP connection, causing it to go down.

Answer

The BGP neighbor is not configured with the password command.

Answer

The route-target import/export values are incorrect for the customer.

Answer

The engineer forgot to configure the VRF under the BGP router-id.

Question 10

A network engineer runs the following command on Router R1:

R1# show ip route vrf CUSTOMER-A

VRF CUSTOMER-A:
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 10.0.1.1 to network 0.0.0.0

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
C        10.0.0.0/30 is directly connected, GigabitEthernet0/0.100
L        10.0.0.1/32 is directly connected, GigabitEthernet0/0.100
B        10.0.2.0/24 [200/0] via 192.168.1.2, 00:12:34

Based on this output, what can be concluded?

Accepted Answer

VRF CUSTOMER-A has a BGP-learned route to 10.0.2.0/24. The output shows a BGP-learned route to 10.0.2.0/24 with the code 'B' and the administrative distance [200/0], indicating it is an external BGP route. The route is installed in the VRF CUSTOMER-A routing table, confirming that VRF CUSTOMER-A is using BGP and has learned this prefix via BGP from the next-hop 192.168.1.2.

Answer

VRF CUSTOMER-A is not using BGP for routing

Answer

The default route is learned via BGP

Answer

GigabitEthernet0/0.100 is not associated with VRF CUSTOMER-A

VRF and Path Isolation

350-401 VRF and Path Isolation — Practice Questions

What is the default OSPF hello interval on an Ethernet link?

Which BGP attribute is preferred when it has the lowest value?

What is the maximum hop count for EIGRP?

Drag and drop the steps of VRF-Lite inter-VRF route leaking configuration into the correct order, from first to last.

Drag and drop the steps of MPLS Layer 3 VPN VRF configuration on a PE router into the correct order, from first to last.

Drag and drop the steps of VRF-aware NAT configuration for path isolation into the correct order, from first to last.

All 350-401 Objectives