CCNA Timed Practice Test 2 — 10 Questions

Question 1

A user reports that their computer cannot access the network. The technician checks the computer's IP configuration and finds an APIPA address (169.254.x.x). The computer is connected to a switch port on VLAN 20. The DHCP server is located on VLAN 1. The technician then examines the router's interfaces using 'show ip interface brief' and sees that all interfaces shown are up/up. What should the technician do next?

Accepted Answer

Verify that the ip helper-address command is configured on the router's VLAN 20 interface.. The APIPA address (169.254.x.x) indicates the host failed to obtain a DHCP lease. Since the DHCP server is on VLAN 1 and the host is on VLAN 20, a DHCP relay (ip helper-address) must be configured on the router's VLAN 20 interface to forward DHCP broadcast messages to the server. The 'show ip interface brief' shows all interfaces are up/up, so the next logical step is to verify the relay configuration.

Answer

Check the DHCP server logs to see if it is receiving Discover messages.

Answer

Attempt to ping the DHCP server's IP address from the host's APIPA address.

Answer

Restart the DHCP service on the server and recheck the host.

Question 2

A network administrator at a large enterprise notices that the network monitoring system frequently generates false positive alerts for unusual traffic patterns during normal business hours. The administrator wants to reduce these false positives while still detecting genuine security threats. Which AI/ML concept would best address this requirement?

Accepted Answer

Implement an anomaly detection system that uses machine learning to establish baseline behavior and flag deviations.. Anomaly detection using machine learning establishes a dynamic baseline of normal network behavior, allowing the system to flag only significant deviations. This reduces false positives during normal business hours while still detecting genuine threats that deviate from the learned baseline, unlike static thresholds that trigger alerts on routine traffic variations.

Answer

Deploy a predictive analytics model to forecast future traffic volumes and adjust thresholds accordingly.

Answer

Apply intent-based networking to automatically enforce security policies based on high-level business intent.

Answer

Use deep packet inspection to examine all traffic and create static rules for known threats.

Question 3

Based on the exhibit, why are clients in VLAN 70 failing to resolve hostnames even though they can reach remote IP addresses?

Accepted Answer

The clients are missing valid DNS server information.. The strongest explanation is that the clients are missing valid DNS server information. In practical terms, successful reachability to remote IP addresses proves that Layer 3 forwarding is working. The failure occurs only when a hostname is used, which points to a naming service problem rather than a general connectivity problem. The DHCP scope shown provides an address and default gateway, but no DNS server option is defined.

This is a very realistic IP-services troubleshooting pattern because the network path works while application usability still fails.

Answer

The default gateway must be removed from the DHCP scope.

Answer

The clients must use PPP before DNS works.

Answer

The VLAN must be converted to the native VLAN on all trunks.

Question 4

Match each network service to its primary function.

Accepted Answer

DNS: Translates domain names to IP addresses. Each network service has a distinct primary function: DNS translates names to IPs, DHCP automates IP assignment, NTP synchronizes time, SNMP manages devices, FTP transfers files, and HTTP serves web content.

Answer

DNS: Assigns IP addresses dynamically to devices on a network

Answer

DNS: Synchronizes time across network devices

Answer

DNS: Manages and monitors network devices

Question 5

Match each HTTP method to its common REST API action.

Accepted Answer

GET - Retrieve data. GET retrieves data; POST creates; PUT replaces; PATCH partially updates; DELETE removes; OPTIONS queries available methods.

Answer

GET - Create data

Answer

POST - Retrieve data

Answer

PUT - Partially update data

Question 6

A network administrator is troubleshooting a connectivity issue between two remote sites connected via a WAN link. Hosts on VLAN 10 at Site A (192.168.10.0/24) cannot ping the server at Site B (10.10.20.100). The router at Site A has a default route configured with the next-hop IP address 10.10.10.2. The administrator checks the routing table on Router A and notices that the default route is not installed. What is the most likely cause of the problem?

Accepted Answer

The next-hop router 10.10.10.2 is unreachable.. The default route uses a next-hop IP (10.10.10.2) and will only be installed in the routing table if that next-hop is reachable. Since the router’s routing table shows no default route, the most likely cause is that the next-hop 10.10.10.2 is unreachable, preventing the static route from being used. This explains why traffic fails despite the configuration.

Answer

The static route for 10.10.20.0/24 is missing from the routing table.

Answer

The GigabitEthernet0/0 interface is administratively down.

Answer

The default route is not configured; the gateway of last resort is missing.

Question 7

You are connected to SW1 via the console. SW1 is a Layer 2 switch. Port GigabitEthernet0/1 connects to a PC in VLAN 10, and port GigabitEthernet0/2 connects to a server in VLAN 20. Both ports are currently in VLAN 1. Configure SW1 to assign GigabitEthernet0/1 to VLAN 10 and GigabitEthernet0/2 to VLAN 20, and verify the configuration.

Accepted Answer

interface GigabitEthernet0/1
switchport mode access
switchport access vlan 10
interface GigabitEthernet0/2
switchport mode access
switchport access vlan 20
end
show vlan brief. Access ports carry traffic for a single VLAN. By assigning G0/1 to VLAN 10 and G0/2 to VLAN 20, the PC and server are placed in their respective VLANs.

Answer

interface GigabitEthernet0/1
switchport mode trunk
switchport trunk allowed vlan 10
interface GigabitEthernet0/2
switchport mode trunk
switchport trunk allowed vlan 20
end
show interfaces trunk

Answer

vlan 10
name PC_VLAN
vlan 20
name Server_VLAN
interface GigabitEthernet0/1
switchport mode access
switchport access vlan 10
interface GigabitEthernet0/2
switchport mode access
switchport access vlan 20
end
show vlan brief

Answer

interface GigabitEthernet0/1
switchport access vlan 10
interface GigabitEthernet0/2
switchport access vlan 20
end
show vlan brief

Question 8

Based on the exhibit, which action is most likely required to allow AP-22 to join the controller successfully?

Accepted Answer

Correct the AP's default gateway so it matches the AP's actual subnet and reachability needs.. The correct action is to fix the AP's default gateway so it can reach the controller's subnet. Option B is wrong because APs use Ethernet, not PPP encapsulation, which is used for serial WAN links. Option C is wrong because CAPWAP does not assign IP addresses; DHCP does, but the AP already has a static IP, and removing it would cause it to fall back to DHCP, which may not fix the gateway issue. Option D is wrong because disabling DHCP on the controller would affect all APs and prevent new APs from obtaining addresses, which is not a targeted fix.

Answer

Change the AP from Ethernet to PPP encapsulation.

Answer

Remove the AP IP address so it can obtain an IP address automatically via DHCP.

Answer

Disable DHCP on the controller for all APs.

Question 9

A switch stack is running PVST+. Users on VLAN 40 lose connectivity for roughly 30 seconds every time the uplink on SW2 flaps. Based on the exhibit, which change would most directly improve convergence for this VLAN?

Accepted Answer

Configure spanning-tree mode rapid-pvst.. The output shows VLAN 40 is still using the legacy IEEE STP process, which converges much more slowly than Rapid PVST+. Moving the switch to rapid-pvst mode gives VLAN 40 the faster proposal/agreement behavior that typically cuts convergence time from tens of seconds to a few seconds.

Answer

Increase the bridge priority on SW2 for VLAN 40.

Answer

Disable PortFast on all access ports.

Answer

Convert the uplink to a routed port.

Question 10

Based on the exhibit, why is traffic to host 198.51.100.70 using the OSPF route instead of the static route?

Accepted Answer

Because the OSPF /26 route is more specific than the static /24 route.. The traffic uses the OSPF route because it is the more specific match. In practical terms, the router evaluates destination-prefix specificity before comparing route source preference. The static route points to a broader /24, while the OSPF entry points to a narrower /26 that still contains the destination. Because longest-prefix match comes first, the /26 route wins.

This is a good reminder that static routes do not automatically beat dynamic routes when the prefixes are different. Specificity matters first, then source preference only when the prefix length is the same.

Answer

Because OSPF always overrides static routing, regardless of prefix length.

Answer

Because the static route must have an administrative distance of 255 to be considered.

Answer

Because the destination 198.51.100.70 is outside both listed routes.