Free N10-009 Show IP Route Output Practice Questions Practice Questions | Courseiva

Scenario guide

How to approach show ip route output practice questions

Practise interpreting routing-table output, route selection, administrative distance, metrics, next hops and longest-prefix match.

Quick answer

Show IP Route Output Practice Questions questions test whether you can apply the concept in context, not just recognise a definition.

How the topic appears in realistic exam-style scenarios.

Which detail in the question changes the correct answer.

How to eliminate plausible but wrong options.

How to connect the question back to the wider exam objective.

Practice set

Practice scenarios

Question 1mediummultiple choice

Full question →

A network engineer is implementing OSPF on a router. All directly connected neighbors are listed with state FULL, but routes from another area are not appearing in the routing table. Which of the following is the most likely cause?

Full question →

Question 2hardmultiple choice

Full question →

A network administrator is configuring OSPF on routers in a multi-area network. The administrator wants to ensure that a router in area 1 does not learn external routes (Type 5 LSAs) injected by an ASBR in area 0, but it must still learn inter-area routes (Type 3 LSAs). The administrator wants to reduce the routing table size. Which OSPF area type should be configured for area 1?

Full question →

Question 3hardmultiple choice

Full question →

A network administrator is creating a performance baseline for a new VoIP application. Which metric is most critical to monitor in order to ensure good voice quality for end users?

Full question →

Question 4hardmultiple choice

Full question →

A network administrator is configuring a monitoring system to collect metrics from network devices. The administrator needs to ensure that the monitoring system can automatically discover the devices and obtain detailed information about their configuration and status, such as interface descriptions and software versions. Which protocol is best suited for this purpose?

Full question →

Question 5hardmultiple choice

Full question →

A network administrator is configuring dynamic routing between two routers in the same organization. The routers must support VLSM, converge quickly, and use a metric that is based on bandwidth and delay. Which routing protocol should be configured?

Full question →

Question 6mediummultiple choice

Full question →

A router receives a packet destined for 10.0.0.15. It has the following routes in the routing table: 10.0.0.0/8 via 192.168.1.1, 10.0.0.0/16 via 192.168.2.1, 0.0.0.0/0 via 192.168.3.1. Which route will be used?

Full question →

Question 7mediummultiple choice

Full question →

A router has two routes to the same destination network: one learned via OSPF with a metric of 10, and another learned via EIGRP with a composite metric of 3072. The default administrative distances are OSPF=110, EIGRP=90. Which route will be installed in the routing table?

Full question →

Question 8hardmultiple choice

Full question →

A network technician is troubleshooting a router that is not forwarding packets to a remote destination network. The routing table shows a valid route learned via OSPF. The technician can successfully ping the next-hop IP address from the router. However, packets to the destination network are not being forwarded. Which of the following is the MOST likely cause?

Full question →

Question 9mediummultiple choice

Full question →

A network engineer is designing an OSPF network for a large enterprise. To reduce the size of routing tables and limit the propagation of external routes, the engineer wants to use a special area that blocks Type 5 LSAs but still allows inter-area routes via a default route. Which type of OSPF area should be configured?

Full question →

Question 10mediummultiple choice

Full question →

A technician is troubleshooting a connectivity issue. A client can successfully ping its default gateway but cannot ping a server located on a different subnet. The router's routing table shows a valid route to the server's network. What should the technician check NEXT?

Full question →

Question 11easymultiple choice

Full question →

What is the default administrative distance for OSPF routes on a typical Cisco router?

Full question →

N10-009 Show IP Route Output Practice Questions

How to approach show ip route output practice questions

Quick answer

Related N10-009 topic practice pages

Network+ network fundamentals practice questions

Network+ implementation practice questions

Network+ operations practice questions

Network+ security practice questions

Network+ troubleshooting practice questions

Practice scenarios

A network engineer is implementing OSPF on a router. All directly connected neighbors are listed with state FULL, but routes from another area are not appearing in the routing table. Which of the following is the most likely cause?

A network administrator is creating a performance baseline for a new VoIP application. Which metric is most critical to monitor in order to ensure good voice quality for end users?

A network administrator is configuring dynamic routing between two routers in the same organization. The routers must support VLSM, converge quickly, and use a metric that is based on bandwidth and delay. Which routing protocol should be configured?

A router receives a packet destined for 10.0.0.15. It has the following routes in the routing table: 10.0.0.0/8 via 192.168.1.1, 10.0.0.0/16 via 192.168.2.1, 0.0.0.0/0 via 192.168.3.1. Which route will be used?

A router has two routes to the same destination network: one learned via OSPF with a metric of 10, and another learned via EIGRP with a composite metric of 3072. The default administrative distances are OSPF=110, EIGRP=90. Which route will be installed in the routing table?

A technician is troubleshooting a connectivity issue. A client can successfully ping its default gateway but cannot ping a server located on a different subnet. The router's routing table shows a valid route to the server's network. What should the technician check NEXT?

What is the default administrative distance for OSPF routes on a typical Cisco router?