Deployment

You are deploying a Cisco Secure Firewall Threat Defense in transparent mode. How are frames forwarded between the internal and external interfaces of the firewall?

Which TWO statements are true regarding NGIPS passive mode deployment?

A security team is deploying a Cisco Secure Firewall Threat Defense device in a data center where the requirement is to inspect traffic flowing between two Layer 3 segments without changing the IP addressing or routing of those segments. The firewall must sit logically between the two segments and forward traffic based on MAC addresses. Which deployment mode should be used?

When deploying an FTD virtual appliance on-prem using VMware ESXi, which virtual network adapter type is recommended for optimal performance?

An engineer is configuring a Cisco Secure Firewall Threat Defense cluster in a data center. To ensure high availability and prevent split-brain scenarios, what is the specific function of the cluster control link (CCL)?

An administrator is planning the deployment of a Cisco Secure Firewall Threat Defense device and needs to choose between routed mode and transparent mode. Which factor strongly favors choosing transparent mode?

An engineer is deploying a Cisco Secure Firewall Threat Defense device in a routed environment where the inside network uses private RFC 1918 addressing and the outside interface receives a dynamic address from the ISP. The requirement is to allow inside hosts to reach the internet without exposing their private addresses, while preserving the ability to add static translations later. Which deployment configuration should be used?

An FTD device is configured in routed mode. What must be configured to allow traffic to exit the network through the firewall?

You are configuring a high availability pair of FTDs. Which interface type is strictly reserved for state synchronization?

You need to configure link redundancy on a Cisco Secure Firewall Threat Defense pair using EtherChannel (Port Channel) across multiple physical interfaces. When configuring LACP (IEEE 802.3ad) for the port channel interface via the Firepower Management Center (FMC), which requirement must be met for successful negotiation?

Which component is responsible for processing traffic in an FTD cluster when 'Distributed' mode is used?

An administrator is troubleshooting an active/standby Cisco Secure Firewall High Availability pair. Stateful failover is enabled, but active long-lived TCP connections are dropping when a failover occurs. Upon checking the stateful inspection settings, what is the most likely cause of this behavior?

When configuring an FTD cluster, what is the purpose of the Control Plane IP address?

An engineer is troubleshooting a high availability failover issue in a Cisco Secure Firewall Threat Defense pair. Which THREE conditions will trigger an automatic failover event in an Active/Standby deployment? (Choose three)

An administrator is configuring a secure firewall deployment in an environment where dynamic routing via OSPF is required across multiple security zones. Which configuration requirement must be met on the Cisco Secure Firewall Threat Defense?

When deploying an FTD in a virtual environment, what is the primary role of the 'GigabitEthernet0/0' interface by default?

Which component is mandatory for managing multiple FTD devices in a distributed enterprise deployment?

An administrator is configuring high availability for Cisco Secure Firewall Threat Defense using Cisco FMC. Which TWO configuration steps are required during the initial setup of an Active/Standby HA pair? (Choose two)

An administrator is configuring inline interface pairs on a Cisco Secure Firewall Threat Defense device. Which THREE characteristics apply to inline deployment mode? (Choose three)

Which TWO of the following are valid methods for deploying an FTD appliance?

A network administrator is preparing to register a new Cisco Secure Firewall Threat Defense device with a Cisco Secure Firewall Management Center. The device is currently running a supported software version and has network connectivity to the management center. Which action must the administrator take on the FTD device to begin the registration process?

In an FTD clustering deployment, how does the control plane communicate state information between the master and slave units?

An administrator needs to deploy an FTD in inline mode for IPS functionality but must ensure that the traffic remains uninterrupted if the software process fails. Which feature should be enabled?

Which FTD deployment mode is best suited for an environment where the device should monitor traffic without performing any blocking or dropping actions?

An administrator is configuring security zones on a Cisco Secure Firewall Threat Defense. Which TWO rules regarding security zones and interface assignments are correct? (Choose two)

An engineer is deploying a Cisco Secure Firewall Threat Defense device in transparent mode between two routers. The design requires that the device forward traffic without modifying the IP headers and that it support multiple VLANs on the same physical interface. Which configuration must the engineer apply?

Which TWO FTD interface types are commonly used for connectivity to an ISP?

An administrator is deploying a Cisco Secure Firewall Virtual (Fv) appliance in an Amazon Web Services (AWS) environment. Which licensing model is typically supported for traffic throughput and feature activation during this cloud deployment?

In routed mode, what is the purpose of the 'Name' assigned to an interface?

An administrator is deploying static route tracking combined with IP SLA on a Cisco Secure Firewall Threat Defense device managed by Cisco FMC. Which TWO components must be configured to implement this feature successfully? (Choose two)

An engineer has deployed an active/standby High Availability pair of Cisco Secure Firewall Threat Defense devices. A failure occurs on the active unit, and a failover successfully takes place. However, upon recovery of the original active unit, it immediately resumes its role as the active unit, causing a brief secondary interruption. Which failover setting governs this behavior?

An engineer is configuring NGIPS inline sets on a Cisco Secure Firewall Threat Defense deployment. Which THREE configuration options or behaviors are associated with inline sets? (Choose three)

An enterprise is deploying a Cisco Secure Firewall Threat Defense cluster. During the setup of the Cluster Control Link (CCL), the administrator must ensure specific networking criteria are met. What is a primary design requirement for the CCL interface?

Which THREE features are critical for maintaining a stable FTD cluster?

In an FTD cluster, which unit is responsible for assigning flow ownership to other units in the cluster?

When registering a new Cisco Secure Firewall Threat Defense device to Cisco Defense Orchestrator (CDO) or Cisco FMC, what is the primary prerequisite protocol or connectivity requirement that must be established from the managed device toward the management platform?

An administrator is configuring port channels (EtherChannels) on Cisco Secure Firewall Threat Defense interfaces. Which TWO requirements or guidelines must be followed? (Choose two)

Which THREE items are synchronized across an FTD high availability pair?

An administrator is planning the deployment of Cisco Secure Firewall Virtual in a public cloud environment (AWS or Azure). Which TWO deployment practices are recommended for ensuring high availability and performance? (Choose two)

Which TWO of the following are valid high availability modes for FTD?

In which mode does the FTD firewall act as a Layer 3 hop and perform NAT?

An administrator is configuring static route tracking on a Cisco Secure Firewall Threat Defense deployment to handle link failure. If the tracked object goes down, the static route should be removed from the routing table. Where is this configuration managed when using Cisco FMC?

Which interface configuration mode allows the FTD to handle traffic across multiple physical links as a single logical interface?

Which THREE items are required to create a port channel on an FTD device?

Which TWO of the following are valid reasons to use Transparent Mode?

When considering virtual FTD deployments, which THREE factors significantly impact the performance of the instance?

Which type of FTD interface should be configured to connect to a trunk port on a switch?

When using clustering with FTD, what is the 'Flow Owner' in the context of traffic distribution?

Which THREE considerations must be addressed when deploying FTDv in a public cloud?

You are configuring static route tracking on an FTD device. What is the primary purpose of this configuration?

When deploying a Cisco Secure Firewall Threat Defense in transparent mode, how are the firewall interfaces configured to pass traffic between segments without routing?

You are troubleshooting a port channel failure on an FTD device. The port channel is 'Up/Down'. What is the most likely cause?

When configuring an NGIPS appliance in passive mode, how does the system handle traffic flow to ensure monitoring without impacting the production network?

An engineer is troubleshooting a stateful failover issue in a Cisco Secure Firewall Threat Defense Active/Standby high availability pair. The firewall units are passing data traffic, but failover state synchronization fails. Which dedicated interface must be verified for correct physical connectivity and configuration?

An engineer is troubleshooting a Cisco Secure Firewall Threat Defense clustering deployment where configuration synchronization between the control node and a data node has failed. Which THREE diagnostic steps or log sources should the engineer check? (Choose three)

Which component in an FTD cluster handles the 'Health Check' process to determine if a node is still active?

An engineer is deploying Cisco Secure Firewall Threat Defense in a routed environment where the inside network uses private RFC 1918 addresses and the outside interface connects to an ISP. The requirement is that inside hosts can reach the internet, but the firewall must not translate traffic destined for an internal server farm that is also reachable through a secondary internal interface. Which configuration approach correctly meets this requirement?

Which of the following must be identical on both units of an FTD high availability pair to ensure successful synchronization?

In an FTD high availability pair, what happens to the standby unit if it loses the heartbeat signal on the failover link?

An enterprise is deploying a high-availability cluster of Cisco Secure Firewall Threat Defense devices to scale performance. Which requirement must be met regarding the physical switch infrastructure connecting the cluster nodes?

What is the consequence of configuring an FTD interface with 'Non-Promiscuous' mode in a virtualized deployment?

When deploying a Cisco Secure Firewall Threat Defense device, what is the purpose of configuring Security Zones?

An enterprise is deploying Cisco Secure Firewall Threat Defense virtual appliances on-premises using VMware ESXi. Which THREE prerequisites or hypervisor configurations are required for proper operation? (Choose three)

You are deploying a Cisco Secure Firewall Threat Defense cluster in a data center environment. Which deployment requirement must be strictly followed regarding the control link and data interfaces?

An engineer is troubleshooting a Cisco Secure Firewall Threat Defense virtual appliance deployed in Microsoft Azure. Connectivity tests show intermittent packet drops. Which THREE troubleshooting steps or configurations should be verified in Azure and FTDv? (Choose three)

When utilizing static route tracking, what value represents the frequency of the tracking probe?

Which protocol is used by the FTD to communicate with the FMC for management traffic?

An administrator is configuring Equal-Cost Multi-Path (ECMP) routing on a Cisco Secure Firewall Threat Defense deployment to balance traffic across two upstream next-hop routers. How does the firewall select the specific path for a given TCP flow?

You are deploying a Cisco Firepower Threat Defense (FTD) device in transparent mode. Which requirement must be met to allow traffic flow through the firewall?

You are deploying FTD in a cloud environment. What is the primary purpose of the 'Management Interface' when launching the virtual instance?

You are deploying a Cisco FTD High Availability pair. During the synchronization process, what occurs when the standby unit fails to receive three consecutive heartbeat hellos from the primary?

When configuring a Port Channel on an FTD, what is the primary benefit of using LACP (Link Aggregation Control Protocol)?

You need to implement static route tracking on an FTD to ensure traffic fails over to a secondary ISP. Which object is used to define the reachability check?

An administrator is configuring an inline interface pair on a Cisco Secure Firewall Threat Defense device using Cisco FMC. The business requires that if the firewall experiences a power failure or kernel panic, traffic must continue to flow uninterrupted through the network segment. Which action should the administrator take?

Which TWO components must be configured to manage an FTD via the FMC?

An administrator is troubleshooting a Stateful High Availability (HA) pair of Cisco Secure Firewall 4100 series devices managed by FMC. The units are failing to form an HA state, and logs indicate a state mismatch on the control link. Which underlying cause is most likely preventing the HA synchronization?

An engineer is deploying Cisco Secure Firewall Threat Defense in a complex multi-zone routed environment. Which THREE design considerations apply when implementing routed mode interfaces? (Choose three)

You are configuring a static route on a Cisco Secure Firewall Threat Defense using FDM. Which parameters are strictly required to create a valid IPv4 static route?

An engineer is troubleshooting a passive NGIPS deployment where the Cisco Secure Firewall is connected to a switch SPAN port. Security analysts report that certain VLAN-tagged packets are not appearing in the event logs. What is the most likely cause?

An engineer is deploying a Cisco Secure Firewall Threat Defense Virtual (FTDv) instance in an Amazon Web Services (AWS) VPC. The deployment requires the FTDv to inspect traffic crossing between public and private subnets. Which AWS architectural construct is mandatory for routing traffic through the FTDv instance?

An engineer is configuring static route tracking on a Cisco Secure Firewall Threat Defense to ensure high availability for outbound internet connectivity. A backup static route is configured with a higher metric. What mechanism does the firewall use to dynamically switch from the primary route to the backup route when the primary next-hop fails?

Which THREE factors affect the choice between deploying FTD in Routed vs Transparent mode?

An engineer is deploying an NGIPS inline set across two physical interfaces. To prevent network disruption during maintenance, the engineer needs to ensure that if the firewall loses power or experiences a kernel panic, traffic can still traverse the physical link. Which hardware feature must the interfaces support?

Which TWO of the following are required for FTD transparent mode deployment?

An engineer deploys an NGIPS in passive mode using a SPAN (Switched Port Analyzer) port on a core switch. During traffic analysis, the engineer notices that the firewall is not seeing TCP reset packets generated by internal servers. What is the primary operational limitation of deploying an NGIPS in passive mode that explains this behavior?

An administrator is setting up a high availability pair of Cisco Secure Firewall devices. During the HA configuration wizard in FMC, the administrator is asked to provide a registration key. What is the purpose of this key?

An engineer is deploying a Cisco Secure Firewall Threat Defense Virtual (FTDv) in Google Cloud Platform (GCP). The architecture requires multiple network interfaces. How does GCP map these interfaces during deployment?

When configuring ECMP (Equal-Cost Multi-Path) on FTD, what happens if one of the next-hop paths fails?

A network security engineer is deploying a Cisco Secure Firewall Threat Defense (FTD) device in a routed mode with two interfaces: inside (10.1.1.1/24) and outside (203.0.113.2/24). The engineer wants to allow inside hosts to reach the internet while ensuring that return traffic is permitted without creating overly permissive rules. The FTD is managed by FMC. Which deployment approach should the engineer use to meet these requirements?

When deploying an FTD appliance, which interface role is used for receiving traffic from a SPAN port?

An administrator is managing high availability failover events for Cisco Secure Firewall Threat Defense devices using Cisco FMC. Which TWO actions or events will trigger a failover from the active unit to the standby unit? (Choose two)

When deploying an FTD virtual appliance in AWS, which feature allows the FTD to scale horizontally to handle varying traffic loads?

An administrator is configuring static route tracking on a Cisco Secure Firewall Threat Defense device managed by FMC. A tracked IP address becomes unreachable, and the primary static route is removed from the routing table. What mechanism does FTD use to verify the reachability of the tracked destination?

An engineer is deploying a Cisco Secure Firewall Threat Defense device in a high-availability pair using Active/Standby failover. The team wants to verify which configuration items must match on both units for failover to operate correctly. (Choose two.)

A network engineer is deploying a Cisco Secure Firewall Threat Defense cluster in spanned EtherChannel mode on two Cisco Nexus switches. The engineer must ensure that the cluster control unit and data units use the correct interfaces and that the cluster operates as designed. Which statement accurately describes the interface requirements for this deployment?

Which deployment scenario represents the correct use case for deploying a Cisco Secure Firewall Threat Defense in passive NGIPS mode?

Which FTD deployment mode must be selected to use the device as a transparent bump-in-the-wire for security inspection?

You are configuring an active/standby High Availability pair for Cisco Secure Firewall Threat Defense using FMC. You need to configure port channels for the data interfaces to increase bandwidth and redundancy. Which guideline must be followed regarding port channels in an HA deployment?

You are deploying a Cisco Secure Firewall Threat Defense in an existing core network as an out-of-band intrusion prevention system. Which NGIPS deployment mode should you configure to ensure the firewall performs deep packet inspection and generates alerts without dropping any production traffic in the event of a device failure or high load?

An engineer is deploying a pair of Cisco Secure Firewall Threat Defense appliances managed by a Firewall Management Center. The requirement is that the two appliances share a single management IP address and a single data IP address so that downstream routers only need one next-hop address, and failover must occur automatically when the active unit fails. Which deployment mode should the engineer configure?

You are troubleshooting high availability. The units are connected, but the failover link shows as 'Down'. What is the most likely cause?

An enterprise network design incorporates Equal-Cost Multi-Path (ECMP) routing across two Cisco Secure Firewall Threat Defense units functioning independently in routed mode. What is the primary benefit of enabling ECMP on the firewalls?

Which FTD command-line tool is primarily used to check interface status and physical link state?

A security team is deploying a Cisco Secure Firewall Threat Defense device in a routed mode at the perimeter. They need to ensure that the device can be managed out-of-band on a dedicated network, separate from the data traffic, and that management traffic does not traverse the data interfaces. Which deployment approach should they use?

In an FTD cluster, what happens if the cluster control link fails?

An administrator configures a Cisco Secure Firewall Threat Defense cluster. During normal operations, a data node experiences a critical hardware failure. What happens to the active connections currently processed by that specific failed data node?

You are deploying an FTD in a cloud environment and need to ensure high availability. Which technology is typically used to manage the virtual IP failover?

Which of the following is a limitation when deploying an FTD in transparent mode?

You are configuring an NGIPS mode deployment on an FTD device. You need to ensure that the FTD can drop malicious traffic in real-time. Which mode must you select?

An engineer is deploying a Cisco Secure Firewall Threat Defense device managed by a Firewall Management Center in a high-availability pair. The engineer configures the failover link and state link, verifies interface monitoring, and then applies the configuration. After applying, the standby unit shows as failed and does not synchronize. Which action should the engineer take to resolve the issue?

Which TWO of the following are benefits of using a Port Channel on an FTD?

When using a Redundant Interface, what is the primary behavior during a link failure?

An administrator is configuring a static route tracking mechanism on a Cisco Secure Firewall Threat Defense device using an ICMP Echo IP SLA object. What happens to the tracked static route if the SLA probe fails to receive a response?

A security engineer is deploying a Cisco Secure Firewall Threat Defense device in transparent mode at a data center. The device must inspect traffic between two Layer 3 subnets without changing the IP addressing scheme. The engineer configures a bridge group and assigns two interfaces to it. Which statement describes the correct behavior of the bridge group in transparent mode?

An administrator is managing Cisco Secure Firewall Threat Defense devices using Cisco Defense Orchestrator (CDO). Which TWO capabilities does CDO provide for firewall deployment and management? (Choose two)

An administrator is configuring a new Cisco Secure Firewall Threat Defense in routed mode on Firepower Device Manager (FDM). During the initial setup, the administrator needs to define the routing behavior for a multi-zone deployment. Which configuration step is mandatory when setting up routed mode?

A security administrator is deploying a Cisco Secure Firewall Threat Defense (FTD) device and needs to configure the management interface for initial setup. The administrator plans to use the default management IP address and then change it to a static address. Which default management IP address and subnet mask are preconfigured on a new FTD appliance?