CCNA Practice Question: A network administrator is configuring a Cisco switch port that connects to a server
A network administrator is configuring a Cisco switch port that connects to a server. The server's NIC is configured for full-duplex and 1 Gbps. The administrator wants to ensure the switch port operates at the same settings without negotiation. Which command set should be applied to the interface?
⚠ Common exam trap
The trap here is assuming that partial manual configuration (e.g., speed only) is sufficient, but both speed and duplex must be manually set to avoid negotiation.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
speed 1000 and duplex full
When a server NIC is manually configured for a specific speed and duplex, the switch port should be configured identically to prevent duplex mismatch and ensure stable operation. The commands speed 1000 and duplex full disable auto-negotiation and set the port to 1 Gbps full-duplex, matching the server. Using auto-negotiation on either side can result in a mismatch, leading to collisions and poor performance.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✗
speed auto and duplex auto
Why it's wrong here
Setting speed auto and duplex auto enables auto-negotiation, which may result in a different speed or duplex if the server is not properly negotiating. The scenario requires the switch port to operate at the same settings without negotiation. Auto-negotiation could lead to a mismatch if the server is hard-coded, causing performance issues. Therefore, this is not the correct choice.
- ✗
speed auto and duplex full
Why it's wrong here
Setting speed auto and duplex full allows the speed to be auto-negotiated while forcing full-duplex. This is problematic because auto-negotiation of speed typically also negotiates duplex; forcing duplex full while speed is auto can lead to a mismatch. The scenario requires both speed and duplex to be set without negotiation, so this is not correct.
- ✓
speed 1000 and duplex full
Why this is correct
To force the switch port to operate at 1 Gbps and full-duplex without auto-negotiation, you must manually set both speed and duplex. The commands speed 1000 and duplex full disable auto-negotiation and lock the settings. This matches the server's fixed configuration and avoids duplex mismatch. It is the correct approach when the server NIC does not support auto-negotiation or when manual settings are desired.
- ✗
speed 1000 and duplex auto
Why it's wrong here
Setting speed 1000 and duplex auto forces the speed but allows duplex to be auto-negotiated. This can cause a duplex mismatch if the server is set to full-duplex but the switch port negotiates half-duplex due to auto-negotiation. The requirement is to avoid negotiation entirely, so duplex must also be manually set. Thus, this combination is incorrect.
Go deeper
Related to this question
Learn chapter
OSPF vs EIGRP: Side-by-Side Comparison
Key term
Duplex mismatch
A duplex mismatch occurs when two connected network devices are configured with different duplex settings (one half-duplex, one full-duplex), leading to poor performance and data errors.
Key term
CAN
A CAN (Controller Area Network) is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other without a host computer.
About these practice questions
Courseiva writes every 200-301 question from scratch — 1,352 in total, each with an explanation and a wrong-answer breakdown. None are copied from real exams or dumps. Learn why practice questions differ from exam dumps →
You might also like
Similar 200-301 questions
- Which three of the following are characteristics of wireless LAN (WLAN) operation in the 2.4 GHz and 5 GHz bands? (Choos…
- Which TWO statements accurately describe the characteristics and deployment considerations for fiber optic cabling in a…
- A network engineer is configuring a Cisco router interface with the IP address 192.168.10.1/24. The engineer wants to en…
- A host address is 192.168.1.14/29. Which address is the broadcast address for that host’s subnet?
- A Windows 10 workstation (Host-A) can ping its default gateway and can ping the public address 8.8.8.8, but users cannot…
Written and reviewed by Johnson Ajibi, MSc IT Security
Security Systems Architect · founder of Courseiva
Last reviewed September 2026 · checked against the official Cisco exam blueprint
This 200-301 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 200-301 exam.