Question 1mediumdrag order
Open the full BGP breakdown →Answer choices are not available in this preview. Open the full question page for the complete review.
Question 243 of 1,705
ANS-C01 Network Management and Operations Practice Question
This ANS-C01 practice question tests your understanding of network management and operations. This is a configuration task: choose the command set that satisfies every stated requirement. Small differences — like 'secret' vs 'password' or 'transport input ssh' vs 'all' — change whether the answer is correct. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Arrange the steps to configure BGP on a Cisco router for a Direct Connect private virtual interface:
Correct answer & explanation
First enter config mode, enable BGP, define the neighbor, advertise prefixes, then verify.
Key principle: OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Common exam traps
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Detailed technical explanation
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
- OSPF neighbours must agree on key parameters.
- Router ID selection can affect neighbour relationships and LSDB output.
- OSPF cost influences the preferred path.
- A route can appear in OSPF information but not become the installed route.
TExam Day Tips
- Check area mismatch first when OSPF adjacency fails.
- Review passive interfaces when a network is advertised but no neighbour forms.
- Use show ip ospf neighbor and show ip route clues carefully.
Key takeaway
OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Real-world example
How this comes up in practice
A cloud solutions architect for a retail company is evaluating services for a new workload. The correct answer here reflects best practice for the specific scenario described — not a general cloud recommendation. OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough. Cloud exam questions reward reading the constraint carefully: the same technology can be right or wrong depending on the use case.
What to study next
Got this wrong? Here's your next step.
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related ANS-C01 OSPF questions on adjacency and route selection.
- →
Network Management and Operations — study guide chapter
Learn the concepts, then practise the questions
- →
Network Management and Operations practice questions
Targeted practice on this topic area only
- →
All ANS-C01 questions
1,705 questions across all exam domains
- →
AWS Certified Advanced Networking Specialty ANS-C01 study guide
Full concept coverage aligned to exam objectives
- →
ANS-C01 practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related ANS-C01 practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
Network Management and Operations practice questions
Practise ANS-C01 questions linked to Network Management and Operations.
Network Security, Compliance and Governance practice questions
Practise ANS-C01 questions linked to Network Security, Compliance and Governance.
Network Design practice questions
Practise ANS-C01 questions linked to Network Design.
Network Implementation practice questions
Practise ANS-C01 questions linked to Network Implementation.
ANS-C01 fundamentals practice questions
Practise ANS-C01 questions linked to ANS-C01 fundamentals.
ANS-C01 scenario practice questions
Practise ANS-C01 questions linked to ANS-C01 scenario.
ANS-C01 troubleshooting practice questions
Practise ANS-C01 questions linked to ANS-C01 troubleshooting.
Practice this exam
Start a free ANS-C01 practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this ANS-C01 question test?
Network Management and Operations — This question tests Network Management and Operations — OSPF neighbours must agree on key parameters..
What exam trap should I watch out for?
Common exam trap: OSPF can fail even when IP connectivity looks correct: OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
What should I do if I get this ANS-C01 question wrong?
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related ANS-C01 OSPF questions on adjacency and route selection.
What is the key concept behind this question?
OSPF neighbours must agree on key parameters.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Keep practising
More ANS-C01 practice questions
- A company is designing a network security architecture for a multi-account environment using AWS Transit Gateway. The se…
- A company is using AWS Direct Connect to connect its on-premises network to AWS. The company wants to encrypt all traffi…
- A company uses AWS Transit Gateway to connect multiple VPCs and on-premises networks via AWS Site-to-Site VPN. The secur…
- A global e-commerce company uses a hub-and-spoke network topology with a transit VPC in us-east-1. Each spoke VPC has an…
- A company is designing a multi-VPC architecture in the same region. The VPCs need to communicate with each other using p…
- A company is deploying an application that requires low-latency communication between EC2 instances in two different AWS…
Last reviewed: Jun 11, 2026
This ANS-C01 practice question is part of Courseiva's free Amazon Web Services certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the ANS-C01 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.