CCNP Virtualization — All Questions With Answers

Question 1

A network engineer is troubleshooting a Cisco IOS-XE router that hosts multiple virtual routing and forwarding (VRF) instances. Users in VRF-A report they cannot reach a server in VRF-B. The engineer verifies that both VRFs have the correct routes and that the router has a route leaking configuration using route-target import/export. However, connectivity still fails. What is the most likely cause?

Accepted Answer

The import map is missing in VRF-B.. Option D is correct because route leaking between VRFs using route-target import/export requires both an export configuration on the source VRF and an import configuration on the destination VRF. If VRF-B lacks an import map (or the route-target import statement), it will not accept the routes exported from VRF-A, even if VRF-A has the correct export configuration. This is a common misconfiguration in MPLS L3VPN or VRF-lite route leaking scenarios.

Answer

The router does not have iBGP configured between the VRFs.

Answer

The route-target export is not configured in VRF-A.

Answer

The router is using VRF-lite, which does not support route leaking.

Question 2

A data center uses Cisco Nexus 9000 switches with VXLAN EVPN to provide network virtualization. The operations team notices that VLAN 100 (mapped to VNI 10100) is not reachable across the fabric, although other VLANs work fine. The NVE interface is up, and the EVPN address-family is configured. Which two actions should the engineer take to isolate the issue?

Accepted Answer

Verify that VLAN 100 is mapped to VNI 10100 consistently on all VTEPs.. Option C is correct because VXLAN EVPN requires consistent VLAN-to-VNI mapping across all VTEPs in the fabric. If VLAN 100 is mapped to VNI 10100 on some switches but not others, traffic for that VNI will not be forwarded correctly, as the mapping is used to associate local VLANs with the VXLAN segment. Option D is correct because the VNI must be explicitly enabled under the NVE interface to participate in VXLAN tunnel termination; without it, the VTEP will not encapsulate or decapsulate traffic for VNI 10100.

Answer

Check if EVPN type-3 routes are being advertised for VNI 10100.

Answer

Confirm that multicast group 239.1.1.1 is reachable across the underlay.

Answer

Check if the MTU on the underlay is set to at least 1550 bytes.

Question 3

A network engineer is deploying a Cisco Catalyst 9300 switch as a virtual switch using StackWise Virtual. The switch will connect to two upstream routers for redundancy. What is the best practice for connecting the uplinks?

Accepted Answer

Bundle the uplinks into an EtherChannel that spans both stack members.. Option A is correct because in a StackWise Virtual deployment, the two member switches operate as a single logical switch. Bundling the uplinks into an EtherChannel that spans both stack members provides both link redundancy and load balancing, and it ensures that if one member fails, traffic continues to flow through the remaining member without requiring routing protocol convergence or STP reconvergence.

Answer

Use two separate routed interfaces, each with a routing protocol.

Answer

Connect each uplink to the active switch member.

Answer

Configure the uplinks in active/standby mode using STP.

Question 4

A cloud provider uses Cisco ACI to automate provisioning of tenant networks. A new tenant requires a Layer 2 bridge domain that extends to an external Layer 2 network via a VPC. The engineer creates a bridge domain with the settings: Type: Regular, L2 Unknown Unicast: Flood, L3 Unknown Multicast Flood: Flood, and Multi-Destination Flooding: Flood. The VPC is configured as a virtual port channel. The tenant reports that broadcast traffic is not reaching the external network. What is the most likely cause?

Accepted Answer

The L2Out is not configured to flood BUM traffic.. The correct answer is C because the bridge domain is configured to flood BUM (Broadcast, Unknown Unicast, and Multicast) traffic internally, but the L2Out (Layer 2 external connection) must also be explicitly configured to flood BUM traffic to the external network. Without this configuration on the L2Out, the ACI fabric will not forward broadcast or multicast frames across the VPC to the external Layer 2 network, even though the bridge domain itself permits flooding.

Answer

The VPC configuration does not support L2 extension.

Answer

The bridge domain is configured as proxy mode for L2 unknown unicast.

Answer

The bridge domain type should be set to 'L2 Only'.

Question 5

An enterprise uses VMware vSphere to host multiple virtual machines (VMs). The network team wants to implement a virtual firewall on the hypervisor to inspect traffic between VMs on the same ESXi host. Which technology should be used?

Accepted Answer

Deploy a virtual firewall on a vSphere Distributed Switch with a private VLAN.. Option B is correct because deploying a virtual firewall on a vSphere Distributed Switch (VDS) with a private VLAN (PVLAN) allows the firewall to inspect east-west traffic between VMs on the same ESXi host without sending traffic off the host. The VDS supports PVLANs to isolate VM traffic and redirect it to the virtual firewall for inspection, enabling granular security within the hypervisor.

Answer

Use VXLAN to encapsulate traffic and send it to a firewall.

Answer

Use a vSphere Standard Switch and configure port mirroring.

Answer

Deploy a physical firewall and route all VM traffic through it.

Question 6

A network engineer configured three interfaces on a switch as shown. A host connected to Ethernet1/2 sends an untagged frame. Which VLAN will this frame be placed into when it reaches Ethernet1/3?

Accepted Answer

The frame is dropped because VLAN 10 is not allowed.. The switchport on Ethernet1/3 is configured as a trunk with an allowed VLAN list that does not include VLAN 10. When the untagged frame from Ethernet1/2 enters the switch, it is assigned to the native VLAN of the access port (which is VLAN 10 by default or configuration). As the frame is switched to the trunk port Ethernet1/3, the trunk's allowed VLAN list is checked; since VLAN 10 is not permitted, the frame is dropped at the egress trunk port.

Answer

VLAN 999

Answer

VLAN 1

Answer

VLAN 10

Question 7

An engineer configures VXLAN EVPN on a Nexus 9000 switch. The configuration is shown. The switch does not advertise any EVPN routes for VNI 10100. Which configuration change is required to fix this issue?

Accepted Answer

Configure "evpn" and "vni 10100 l2" under the BGP address-family l2vpn evpn.. Option A is correct because for VXLAN EVPN on a Nexus 9000, the BGP address-family l2vpn evpn must explicitly contain the 'evpn' keyword and the 'vni 10100 l2' command to advertise Layer 2 VNI routes. Without this configuration, BGP does not know to inject the VNI's MAC/VTEP information into the EVPN route table, so no EVPN routes are advertised for VNI 10100.

Answer

Remove the mcast-group from the NVE member, because EVPN uses BGP for control plane.

Answer

Change the source-interface to a physical interface.

Answer

Add an IP address to the VLAN 100 interface in the default VRF.

Question 8

Which TWO of the following are benefits of using network virtualization with VXLAN? (Choose two.)

Accepted Answer

Enables Layer 2 extension across Layer 3 boundaries.. VXLAN encapsulates Layer 2 frames in UDP packets over IP, allowing Layer 2 segments to be stretched across Layer 3 networks. This enables virtual machine mobility and multi-tenant environments without being constrained by physical network boundaries.

Answer

Eliminates the need for STP by using a centralized controller.

Answer

Uses only multicast for control plane learning.

Answer

Provides native encryption for data in transit.

Question 9

Which THREE of the following are components of a Cisco ACI fabric? (Choose three.)

Accepted Answer

Spine switch. The spine switch is a core component of a Cisco ACI fabric, forming the spine-leaf topology. Spine switches provide high-speed, non-blocking connectivity between leaf switches and handle all east-west traffic, relying on IS-IS as the routing protocol for fabric discovery and forwarding.

Answer

Firewall

Answer

Router

Question 10

A financial services company has deployed Cisco UCS servers with VMware vSphere 7.0 to host critical trading applications. The network uses Cisco Nexus 9000 switches in a VXLAN EVPN fabric with BGP as the underlay. The environment includes 50 ESXi hosts, each connected via two 40G interfaces to two different leaf switches in a VPC. The VMs are spread across multiple hosts and communicate over VXLAN. Recently, the operations team migrated a set of VMs from an old VLAN-based network to a new VXLAN segment (VNI 50000). After the migration, users report intermittent connectivity issues and packet loss. The engineering team captures traffic and notices that some VMs send ARP requests that are not being replied to, even though the target VM is active. Further analysis shows that the ARP requests are being flooded to all VTEPs, but the replies are not reaching the source. The team checks the underlay and finds no issues with BGP or routing. The NVE interfaces are up, and the VNI is configured. Which of the following is the most likely cause of the issue?

Accepted Answer

The MAC address of the target VM is not being advertised in EVPN type-2 routes because the VM's MAC is learned on a different leaf switch than expected.. The issue is that the target VM's MAC address is not being advertised via EVPN Type-2 routes from the leaf switch where it resides. When the source VM sends an ARP request, the ingress VTEP floods it to all VTEPs in the VNI's ingress replication list, but the reply from the target VM must be unicast back. If the target's MAC is not in the EVPN control plane (e.g., because it was learned on a different leaf than expected due to asymmetric MAC learning or stale entries), the reply cannot be forwarded correctly, causing intermittent connectivity.

Answer

The ingress replication list is missing some VTEPs.

Answer

The symmetric routing configuration is missing on the leaf switches.

Answer

The VPC configuration between the leaf switches and ESXi hosts is incorrect.

Question 11

A network engineer is troubleshooting connectivity issues in a multi-tenant environment where each tenant's traffic is isolated using VRF-Lite. The engineer notices that tenants in the same VRF cannot communicate with each other across different access switches. Which design change should be implemented to enable inter-switch VRF communication?

Accepted Answer

Create trunk links with 802.1Q subinterfaces on each switch and assign each subinterface to the appropriate VRF.. Option B is correct because VRF-Lite requires 802.1Q trunking to extend Layer 3 VRF boundaries across switches. By creating subinterfaces on trunk links and assigning each subinterface to the appropriate VRF, traffic from the same VRF on different switches can be routed through the VRF-specific routing table, enabling inter-switch communication while maintaining isolation.

Answer

Use the same VLAN for all tenants and rely on VLAN ACLs.

Answer

Configure static routes on each switch pointing to the next-hop IP in the global routing table.

Answer

Enable OSPF with a single area on all switches and redistribute between VRFs.

Question 12

An organization is migrating from a traditional three-tier architecture to a leaf-spine fabric using VXLAN EVPN. The design requires that virtual machines can move between racks without IP address changes. Which technology must be enabled at the leaf switches to support this mobility?

Accepted Answer

VXLAN with EVPN control plane.. VXLAN with EVPN control plane (B) is correct because it provides a Layer 2 overlay network that extends VLANs across the leaf-spine fabric, enabling virtual machine mobility without IP address changes. EVPN uses BGP to distribute MAC and IP address information, allowing the leaf switches to learn and forward traffic to VMs regardless of their physical location, which is essential for seamless VM migration between racks.

Answer

Overlay Transport Virtualization (OTV).

Answer

VRF-Lite with route redistribution.

Answer

MPLS L3VPN with BGP.

Question 13

Which TWO statements correctly describe characteristics of virtual device contexts (VDCs) in Cisco Nexus switches?

Accepted Answer

Each VDC can have its own admin account and separate management interface.. Option C is correct because each VDC in a Cisco Nexus switch can be configured with its own administrative credentials and a dedicated management interface (e.g., mgmt0). This allows separate administrative domains and management access per VDC, which is a key feature for multi-tenant environments.

Answer

VDCs allow overlapping VLAN IDs across different VDCs only if using different VNIs.

Answer

VDCs provide Layer 3 routing isolation by default across all VDCs.

Answer

VDCs are supported on all Cisco IOS-XE switches.

Question 14

A network engineer configured VRF TENANT_A and moved the subinterfaces into the VRF. After the change, the CEF table shows the prefixes but the next-hop addresses are unreachable. What is the most likely cause?

Accepted Answer

The next-hop IP addresses are in the global routing table, not in the VRF.. When subinterfaces are moved into a VRF, the CEF table for that VRF will contain the learned prefixes, but the next-hop addresses must also be reachable within the same VRF. If the next-hop IP addresses reside in the global routing table instead of the VRF, the VRF will have no route to those next hops, causing them to be marked as unreachable. This is a common misconfiguration where the next-hop adjacency is not established within the VRF context.

Answer

LISP is not configured to map the virtual network.

Answer

OSPF is not redistributing the routes into the VRF.

Answer

The physical interface is not configured as a trunk.

Question 15

A service provider uses a Cisco ASR 1000 router to provide MPLS L3VPN services to multiple customers. Each customer has their own VRF. Recently, a new customer was added with VRF CUSTOMER_C. After configuration, the customer reports that they can reach some remote sites but not others. The network engineer checks the VRF configuration and finds that the route targets for CUSTOMER_C are correctly configured. The engineer also verifies that BGP sessions to the PE routers are up. The missing routes are from a site that uses a different PE router. Which action should the engineer take to resolve the issue?

Accepted Answer

Verify that the route target import/export values on the remote PE match those on the local PE for VRF CUSTOMER_C.. The issue is that the remote PE router does not have the correct route target import/export configuration for VRF CUSTOMER_C. In MPLS L3VPN, VRFs on different PEs must have matching route target values to import and export VPNv4 routes into the correct VRF. Even if the local PE is correctly configured, the remote PE must also import the routes from the local PE using the same route target. Without this, the remote PE will not install the VPNv4 prefixes into its VRF, causing the customer to be unable to reach sites connected to that remote PE.

Answer

Increase the MTU on the link between the PE routers.

Answer

Reconfigure LDP on the PE routers to establish a targeted session.

Answer

Check the MPLS label stack on the local PE to ensure labels are being swapped correctly.

Question 16

Which TWO statements about virtual switching in a hypervisor environment are correct?

Accepted Answer

A virtual switch can be connected to a physical network through uplink ports.. A virtual switch connects to the physical network through uplink ports, which are typically mapped to physical NICs on the hypervisor host. This allows VMs on the virtual switch to communicate with external networks, making option A correct.

Answer

A virtual switch does not support VLAN tagging.

Answer

A virtual switch performs routing between different subnets.

Answer

A virtual switch is a physical device installed in the hypervisor host.

Question 17

Refer to the exhibit. A network engineer has configured VRFs on a router. A packet arrives on Gi0/1/0 with destination IP 10.1.1.2. Which VRF is used for routing this packet?

Accepted Answer

CUSTOMER-A. The packet arrives on interface Gi0/1/0, which is configured under VRF CUSTOMER-A (as shown in the exhibit with 'ip vrf forwarding CUSTOMER-A'). When a VRF is applied to an ingress interface, the router uses that VRF's routing table (not the global table) to perform the destination IP lookup. Therefore, the packet with destination 10.1.1.2 is routed using the CUSTOMER-A VRF.

Answer

Global routing table

Answer

Mgmt-intf

Answer

CUSTOMER-B

Question 18

A financial company runs a critical trading application in a virtualized environment on VMware vSphere. The application consists of two VMs: App-1 (web server) and App-2 (database server). Both VMs are on the same ESXi host. Recently, users report intermittent slowness during peak trading hours. Monitoring shows that App-1 experiences high CPU ready time (up to 15%) and App-2 has high disk latency (average 50 ms). The ESXi host has 16 vCPUs total (2 sockets, 8 cores each) and 128 GB RAM. The host runs 10 VMs total. App-1 has 4 vCPUs and 16 GB RAM; App-2 has 8 vCPUs and 32 GB RAM. The storage is a shared NFS datastore connected via 1 Gbps Ethernet. The network is 10 Gbps. What is the MOST effective course of action to resolve the performance issues?

Accepted Answer

Reduce the number of vCPUs assigned to App-2 from 8 to 4, and configure Storage I/O Control on the datastore.. Option C is correct because App-2's 8 vCPUs exceed the number of physical cores per socket (8), causing CPU scheduling contention and high ready time on App-1, while reducing vCPUs to 4 aligns with the host's core-per-socket count and reduces co-scheduling overhead. Additionally, Storage I/O Control (SIOC) on the NFS datastore can prioritize disk access and mitigate the high disk latency (50 ms) by enforcing shares and limits during congestion, addressing both performance issues without requiring hardware upgrades.

Answer

Enable vNUMA for both VMs to improve memory access, and set CPU affinity to dedicate specific cores.

Answer

Increase the RAM for both VMs to reduce disk swapping, and enable Hyperthreading on the ESXi host.

Answer

Migrate the VMs to another ESXi host with faster CPUs, and upgrade the storage network to 10 Gbps.

Question 19

Drag and drop the steps to configure OSPF on a Cisco router in the correct order.

Question 20

Drag and drop the steps to configure a site-to-site IPsec VPN on a Cisco router in the correct order.

CCNP Virtualization — All Questions With Answers

A network engineer is deploying a Cisco Catalyst 9300 switch as a virtual switch using StackWise Virtual. The switch will connect to two upstream routers for redundancy. What is the best practice for connecting the uplinks?

An enterprise uses VMware vSphere to host multiple virtual machines (VMs). The network team wants to implement a virtual firewall on the hypervisor to inspect traffic between VMs on the same ESXi host. Which technology should be used?

A network engineer configured three interfaces on a switch as shown. A host connected to Ethernet1/2 sends an untagged frame. Which VLAN will this frame be placed into when it reaches Ethernet1/3?

Exhibit

An engineer configures VXLAN EVPN on a Nexus 9000 switch. The configuration is shown. The switch does not advertise any EVPN routes for VNI 10100. Which configuration change is required to fix this issue?

Exhibit

Which TWO of the following are benefits of using network virtualization with VXLAN? (Choose two.)

Which THREE of the following are components of a Cisco ACI fabric? (Choose three.)

An organization is migrating from a traditional three-tier architecture to a leaf-spine fabric using VXLAN EVPN. The design requires that virtual machines can move between racks without IP address changes. Which technology must be enabled at the leaf switches to support this mobility?

Which TWO statements correctly describe characteristics of virtual device contexts (VDCs) in Cisco Nexus switches?

A network engineer configured VRF TENANT_A and moved the subinterfaces into the VRF. After the change, the CEF table shows the prefixes but the next-hop addresses are unreachable. What is the most likely cause?

Exhibit

Which TWO statements about virtual switching in a hypervisor environment are correct?

Refer to the exhibit. A network engineer has configured VRFs on a router. A packet arrives on Gi0/1/0 with destination IP 10.1.1.2. Which VRF is used for routing this packet?

Exhibit

Drag and drop the steps to configure OSPF on a Cisco router in the correct order.

Drag and drop the steps to configure a site-to-site IPsec VPN on a Cisco router in the correct order.

Match each network device to its primary function.

Match each Cisco switch security feature to its function.

CCNP Virtualization — All Questions With Answers

A network engineer is deploying a Cisco Catalyst 9300 switch as a virtual switch using StackWise Virtual. The switch will connect to two upstream routers for redundancy. What is the best practice for connecting the uplinks?

An enterprise uses VMware vSphere to host multiple virtual machines (VMs). The network team wants to implement a virtual firewall on the hypervisor to inspect traffic between VMs on the same ESXi host. Which technology should be used?

A network engineer configured three interfaces on a switch as shown. A host connected to Ethernet1/2 sends an untagged frame. Which VLAN will this frame be placed into when it reaches Ethernet1/3?

Exhibit

An engineer configures VXLAN EVPN on a Nexus 9000 switch. The configuration is shown. The switch does not advertise any EVPN routes for VNI 10100. Which configuration change is required to fix this issue?

Exhibit

Which TWO of the following are benefits of using network virtualization with VXLAN? (Choose two.)

Which THREE of the following are components of a Cisco ACI fabric? (Choose three.)

An organization is migrating from a traditional three-tier architecture to a leaf-spine fabric using VXLAN EVPN. The design requires that virtual machines can move between racks without IP address changes. Which technology must be enabled at the leaf switches to support this mobility?

Which TWO statements correctly describe characteristics of virtual device contexts (VDCs) in Cisco Nexus switches?

A network engineer configured VRF TENANT_A and moved the subinterfaces into the VRF. After the change, the CEF table shows the prefixes but the next-hop addresses are unreachable. What is the most likely cause?

Exhibit

Which TWO statements about virtual switching in a hypervisor environment are correct?

Refer to the exhibit. A network engineer has configured VRFs on a router. A packet arrives on Gi0/1/0 with destination IP 10.1.1.2. Which VRF is used for routing this packet?

Exhibit

Drag and drop the steps to configure OSPF on a Cisco router in the correct order.

Drag and drop the steps to configure a site-to-site IPsec VPN on a Cisco router in the correct order.

Match each network device to its primary function.

Match each Cisco switch security feature to its function.