Courseiva
CCNA Study GuideCCNA 200-301

What CCNA Learners Get Wrong Most Often: Data from 2,606 Practice Answers

We analysed 2,606 real CCNA practice answers. No domain is dramatically harder than the rest; marks are lost to a handful of specific traps, like picking the next subnet's address as the broadcast.

5 min read
3 sections
Johnson Ajibi
JA

Reviewed by Johnson Ajibi, MSc IT Security, IEEE Senior Member

Network and security engineering since 2012 · Founder, JTNETSOLUTIONS LIMITED & Courseiva

Most CCNA advice is written from memory: someone passed, and tells you what felt hard. We wanted something less anecdotal, so we looked at what actually happens when people practise.

The numbers below come from 2,606 answers by 34 learners working through CCNA 200-301 practice sessions on Courseiva. We stripped out anything that looked automated (accounts running dozens of sessions a day, answers given in under three seconds) and only counted a question once at least five different people had answered it. It's early data, and we'll say where that matters. But it already says something useful.

Finding 1: no domain is the "hard one"

Learners answered 77.7% of questions correctly overall. Split by exam domain, the spread is surprisingly flat:

Domain Accuracy Share of the exam
Switching and Network Access 76% 20%
Network Infrastructure and Connectivity 77% 20%
IP Routing 78% 25%
Network Services and Security 78% 25%
AI and Network Operations 82% 10%

Six points separate the weakest domain from the strongest. If you've been planning your revision around "I'm bad at routing", this is worth sitting with: people don't fail CCNA questions a whole topic at a time. They fail them one specific misconception at a time.

That's what the rest of this article is about.

Finding 2: the wrong answers cluster

For each of the most-missed questions we looked at which wrong answer people chose. On a four-option question you'd expect wrong answers to spread out. They don't. On several questions, most of the people who got it wrong picked the same wrong option, which points straight at the mistake.

The /26 habit on a /27 question

An interface is configured with 10.24.7.158/27. What is the broadcast address of that subnet?

Only 35% got this right. The answer is 10.24.7.159. Of the people who got it wrong, 73% chose 10.24.7.191.

That isn't a random slip. .191 is the broadcast address of the /26 block (128–191). People recognise "158 is in the upper half", reach for a block of 64, and stop. A /27 steps in blocks of 32, so .158 lives in 128–159, and the broadcast is .159.

The fix is mechanical: work out the block size from the prefix every time (256 − 224 = 32), list the boundaries (128, 160) and only then place the host. Our subnetting cheat sheet has the whole method on one page.

The /30 off-by-one

A host is configured with 10.1.1.34/30. Which address is the broadcast address for its subnet?

65% correct; the answer is 10.1.1.35. And 86% of the wrong answers were 10.1.1.36.

Same root cause, smaller block. A /30 steps in fours: 32–35, 36–39. .36 is the next subnet's network address, not this one's broadcast. Picking the next boundary instead of "next boundary minus one" is the single most common subnetting error we see.

"Same first two octets" isn't "same network"

A host with address 172.16.5.10/23 wants to determine whether 172.16.6.20 is on the same local network.

Every single wrong answer here was the same one: "It is on the same local network because /23 covers all addresses in 172.16.5.x and 172.16.6.x."

A /23 does cover two consecutive /24s, but they start on an even third octet. 172.16.5.10/23 belongs to 172.16.4.0/23 (4.x and 5.x). 172.16.6.20 is in the next block, 172.16.6.0/23, so the host sends it to its default gateway. When the interesting octet is the third one, the block size applies there: 256 − 254 = 2.

Interface command, global job

Which command enables IPv6 routing on a Cisco router?

59% correct. The answer is ipv6 unicast-routing, entered in global configuration mode. Of the wrong answers, 57% were ipv6 enable.

ipv6 enable is a real command, which is exactly why it's tempting. But it's an interface command that turns on IPv6 (and a link-local address) on one interface. It doesn't make the router forward IPv6 packets between interfaces. A quick test for any "enable X routing" question: is this something the whole router does? Then it's almost certainly a global command.

The route that exists but isn't used

This one came with an exhibit: a static route to 192.168.40.0/24 via 203.0.113.2 and a default route via 198.51.100.1, but the routing table only shows 198.51.100.0/30 as connected. Traffic to 192.168.40.200 goes out the default route. Why?

59% correct. The answer is that the static route's next hop is unreachable. Of the wrong answers, 86% chose "Default routes always override static routes."

They don't. A more specific route always wins over 0.0.0.0/0. The router simply can't use a static route whose next hop it can't reach, so the route never makes it into the forwarding decision and traffic falls through to the default. When an exhibit shows a route "not working", check whether its next hop is reachable before you reach for a rule about route types.

What to do with this

Three practical things, all of which the data supports:

  1. Stop revising by domain alone. The differences between domains are small; the differences between "I know the rule" and "I apply it under time pressure" are large.
  2. Drill the mechanics, not the definitions. Most of the misses above are people who knew the concept but skipped a step. Do subnetting the slow, explicit way until the slow way becomes fast.
  3. Read your wrong answers, especially the ones you were confident about. A confident wrong answer is a misconception, and it will come back on exam day.

You can see the live version of this data, including the full list of the ten most-missed questions with links to their explanations, in our CCNA data report. We'll update it as more people practise, and add other exams once they have enough learners for the numbers to mean something.

If you'd like to test yourself against these exact traps, start a 30-question CCNA practice set. Every answer comes with an explanation of why the right one is right and why the others aren't.

Practise CCNA questions

Original exam-style practice questions with detailed, explained answers. Track your weak topics and review missed questions before exam day.

Courseiva provides free IT certification practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics. Explore related practice questions for Cisco, CompTIA, Microsoft Azure, AWS, and other certification exams.