JN0-106 Practice Question: Troubleshooting an OSPF issue on a Juniper router
You are troubleshooting an OSPF issue on a Juniper router. The router has a single interface ge-0/0/1 with IP 10.1.1.1/30 connected to a neighbor with IP 10.1.1.2/30. OSPF is configured area 0. The 'show ospf neighbor' command shows no neighbors. 'show interfaces ge-0/0/1 terse' shows the interface is up. 'show configuration protocols ospf' shows:
area 0.0.0.0 {
interface ge-0/0/1.0 {passive;
} }
What is the problem?
⚠ Common exam trap
Candidates often assume 'passive' only prevents the interface from sending routing updates (like in RIP or EIGRP), but in OSPF it blocks all Hello packets, preventing neighbor discovery entirely.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
The OSPF interface is configured as passive
The 'passive' statement under the OSPF interface configuration prevents the router from sending or processing OSPF Hello packets on that interface. Without Hello packets, the router cannot discover neighbors or form adjacencies, which is why 'show ospf neighbor' returns no neighbors even though the interface is operationally up.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✓
The OSPF interface is configured as passive
Why this is correct
Setting an OSPF interface to passive in Junos disables hello packet transmission entirely on that interface. Without hellos, the router cannot discover neighbors or form an adjacency, so the OSPF neighbor state remains Down. The interface stays administratively and protocol up, but OSPF treats it as a stub network, advertising the subnet while never establishing a neighbor relationship. This directly matches a terse output showing the interface up and no OSPF neighbors.
- ✗
The hello timer is too slow
Why it's wrong here
A hello timer that is too slow still allows hellos to be sent, only at longer intervals than the default 10 seconds on broadcast interfaces. OSPF requires matching hello intervals between neighbors, but even a mismatched or slow timer would still generate packets and could eventually form an adjacency if intervals align. The absence of any neighbor in the OSPF database indicates that no hellos are being transmitted at all, which is characteristic of a passive interface, not a slow timer.
- ✗
Authentication is missing
Why it's wrong here
OSPF authentication is an optional feature and not enabled by default. If authentication were configured on one side but not the other, it would cause a checksum or key mismatch and prevent adjacency formation. However, the problem statement gives no indication that authentication is configured on the router, and OSPF operates normally without it. The lack of neighbors is better explained by a passive interface, which suppresses hellos regardless of authentication settings.
- ✗
The interface is administratively down
Why it's wrong here
An administratively down interface would be displayed in a 'down' state in the interface terse output, and OSPF would not run on it because the physical or logical link is disabled. The provided terse output explicitly shows the interface is up, ruling out any administrative shutdown as the cause. Administrative down is also a deliberate action that disables all traffic, whereas a passive interface leaves the interface operational but restricts only OSPF hello processing.
Visual reference
Quick reference
Routing Protocol Comparison
| Protocol | Metric | Max Hops | Algorithm | Type |
|---|---|---|---|---|
| RIP v2 | Hop count | 15 | Bellman-Ford | Distance vector |
| OSPF | Cost (bandwidth) | Unlimited | Dijkstra (SPF) | Link state |
| EIGRP | Composite metric | Unlimited | DUAL | Hybrid |
| IS-IS | Cost | Unlimited | Dijkstra | Link state |
| BGP | Policy / attributes | Unlimited | Path vector | Path vector |
RIP's 15-hop limit makes it unsuitable for large networks. OSPF and EIGRP dominate modern enterprise deployments.
Go deeper
Related to this question
About these practice questions
Courseiva writes every JN0-106 question from scratch — 326 in total, each with an explanation and a wrong-answer breakdown. None are copied from real exams or dumps. Learn why practice questions differ from exam dumps →
You might also like
Similar JN0-106 questions
- Your company runs a Juniper MX480 router as the core gateway. The router has been experiencing intermittent connectivity…
- Which two commands can be used to monitor real-time interface statistics and errors on a Junos device?
- After a software upgrade, a router fails to boot with the new image. The engineer suspects the image is corrupted. What…
- A network engineer wants to schedule a reboot of a Juniper device at 3:00 AM. Which command should be used?
- A network engineer needs to analyze NTP synchronization status and offset. Which command provides detailed NTP peer info…
Written by Johnson Ajibi, MSc IT Security
Security Systems Architect · founder of Courseiva
This JN0-106 practice question is part of Courseiva's free Juniper Networks certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the JN0-106 exam.