- A
The route is not committed.
Why wrong: If the route were not committed, it would not appear in the routing table.
- B
The next-hop address 10.0.0.1 is not reachable.
If the next-hop is not in the routing table, the static route is not active.
- C
The preference of the static route is higher than 15.
Why wrong: Static routes default preference is 5; a higher preference number makes it less preferred, but it does not cause inactivity by itself.
- D
The destination prefix is already learned via OSPF with a lower metric.
Why wrong: OSPF metric is not compared across protocols; route preference determines active route.
Question 395 of 514
Static Route Not Active Due to Unreachable Next-Hop
This JNCIA-JUNOS practice question tests your understanding of routing fundamentals. This is a configuration task: choose the command set that satisfies every stated requirement. Small differences — like 'secret' vs 'password' or 'transport input ssh' vs 'all' — change whether the answer is correct. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
A network administrator configures a static route on a Juniper device: `set routing-options static route 192.168.100.0/24 next-hop 10.0.0.1`. The administrator verifies the route is present in the routing table but notices it is not active. What is the most likely cause?
Clue words in this question
Noticing these words before you look at the options changes how you read each choice.
Clue:
"most likely"Why it matters: Probability qualifier — the question wants the most probable cause or outcome, not a guaranteed one. Eliminate low-probability options.
Quick Answer
The answer is that the static route is not active because the next-hop address 10.0.0.1 is unreachable. On Junos, a static route will only be installed as an active route in the forwarding table if its next-hop is reachable through a directly connected interface or another active route; if the next-hop is not resolvable via ARP or an existing route, Junos marks the static route as hidden or inactive. This concept directly tests your understanding of Junos route resolution logic on the JNCIA-Junos exam, where a common trap is assuming a static route becomes active simply by being configured—it must have a valid, reachable next-hop. A frequent exam scenario presents a static route present in the configuration but missing from the active route table, and the correct diagnosis is always to check next-hop reachability. Memory tip: think “No hop, no go”—if the next-hop isn’t reachable, the route stays hidden.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
The next-hop address 10.0.0.1 is not reachable.
A static route becomes active only if the next-hop address is reachable via a directly connected or active route in the routing table. Since the administrator verified the route is present but not active, the most likely cause is that the next-hop 10.0.0.1 is not reachable (e.g., no ARP resolution or no interface with that subnet). Junos marks such routes as hidden or inactive until the next hop is reachable.
Key principle: Answer the scenario, not the keyword: identify the specific constraint before choosing the most familiar-sounding option.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✗
The route is not committed.
Why it's wrong here
If the route were not committed, it would not appear in the routing table.
- ✓
The next-hop address 10.0.0.1 is not reachable.
Why this is correct
If the next-hop is not in the routing table, the static route is not active.
Clue confirmation
The clue word "most likely" in the question point toward this answer.
Related concept
Read the scenario before looking for a memorised answer.
- ✗
The preference of the static route is higher than 15.
Why it's wrong here
Static routes default preference is 5; a higher preference number makes it less preferred, but it does not cause inactivity by itself.
- ✗
The destination prefix is already learned via OSPF with a lower metric.
Common exam traps
Common exam trap: answer the scenario, not the keyword
The trap here is that candidates often assume a static route is always active once configured and committed, overlooking Junos's requirement that the next-hop must be reachable via an active directly connected route for the route to be installed as active.
Detailed technical explanation
How to think about this question
In Junos, a static route's next-hop must be resolvable through an active directly connected route or a configured interface; otherwise, the route is placed in the routing table but marked as 'hidden' or 'inactive' (shown with a '#' flag in show route). This behavior is controlled by the 'resolve' option—without it, the next-hop must be on a directly connected subnet. In real-world scenarios, misconfigured static routes to remote next-hops without proper recursive resolution are a common cause of traffic blackholing.
KKey Concepts to Remember
- Read the scenario before looking for a memorised answer.
- Find the constraint that changes the correct option.
- Eliminate answers that are true in general but not in this case.
TExam Day Tips
- Watch for words such as best, first, most likely and least administrative effort.
- Review why wrong options are wrong, not only why the correct option is correct.
Key takeaway
Answer the scenario, not the keyword: identify the specific constraint before choosing the most familiar-sounding option.
Real-world example
How this comes up in practice
A network engineer at a university connects two campus buildings via a fibre link. Both routers run OSPF, but no adjacency forms — even though both routers can ping each other. The engineer finds one router is in area 0 and the other in area 1. OSPF adjacency requires matching area numbers, hello/dead timers, and network type. IP reachability alone is not enough.
Visual reference
What to study next
Got this wrong? Here's your next step.
Identify which exam domain this question belongs to, review the core concept, then practise similar questions from the same domain.
- →
Routing Fundamentals — study guide chapter
Learn the concepts, then practise the questions
- →
Routing Fundamentals practice questions
Targeted practice on this topic area only
- →
All JNCIA-JUNOS questions
514 questions across all exam domains
- →
Juniper Networks Certified Associate Junos JNCIA-Junos study guide
Full concept coverage aligned to exam objectives
- →
JNCIA-JUNOS practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related JNCIA-JUNOS practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
User Interfaces practice questions
Practise JNCIA-JUNOS questions linked to User Interfaces.
Junos Configuration Basics practice questions
Practise JNCIA-JUNOS questions linked to Junos Configuration Basics.
Operational Monitoring and Maintenance practice questions
Practise JNCIA-JUNOS questions linked to Operational Monitoring and Maintenance.
Routing Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Routing Fundamentals.
Networking Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Networking Fundamentals.
Junos OS Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Junos OS Fundamentals.
JNCIA-JUNOS fundamentals practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS fundamentals.
JNCIA-JUNOS scenario practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS scenario.
JNCIA-JUNOS troubleshooting practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS troubleshooting.
Practice this exam
Start a free JNCIA-JUNOS practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this JNCIA-JUNOS question test?
Routing Fundamentals — This question tests Routing Fundamentals — Read the scenario before looking for a memorised answer..
What is the correct answer to this question?
The correct answer is: The next-hop address 10.0.0.1 is not reachable. — A static route becomes active only if the next-hop address is reachable via a directly connected or active route in the routing table. Since the administrator verified the route is present but not active, the most likely cause is that the next-hop 10.0.0.1 is not reachable (e.g., no ARP resolution or no interface with that subnet). Junos marks such routes as hidden or inactive until the next hop is reachable.
What should I do if I get this JNCIA-JUNOS question wrong?
Identify which exam domain this question belongs to, review the core concept, then practise similar questions from the same domain.
Are there clue words in this question I should notice?
Yes — watch for: "most likely". Probability qualifier — the question wants the most probable cause or outcome, not a guaranteed one. Eliminate low-probability options.
What is the key concept behind this question?
Read the scenario before looking for a memorised answer.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Same concept, more angles
4 more ways this is tested on JNCIA-JUNOS
These questions test the same concept from different angles. Work through them to make sure you can recognise it however the exam phrases it.
Variation 1. Refer to the exhibit. A network administrator configured a static route to 10.0.0.0/24 with next-hop 192.168.1.1. The route is not appearing in the active routing table. What is the most likely reason?
hard- ✓ A.The next-hop address is not reachable.
- B.The route is a reject route.
- C.The route is being overridden by an OSPF route with lower preference.
- D.The static route preference is too high.
Why A: The exhibit shows that the route's next-hop type is 'Unreachable', indicating that the next-hop address 192.168.1.1 is not reachable. Since the next-hop is unreachable, the static route cannot be installed in the active routing table. Option B is incorrect because a reject route would show 'Reject' or 'Discard'. Option C is incorrect: even if an OSPF route existed with lower preference (higher priority), the static route would still appear as a backup; the problem here is next-hop unreachability. Option D is incorrect: a static route with preference 5 is low, meaning it is highly preferred; high preference would make it less preferred, but the route is not active due to unreachable next-hop, not preference.
Variation 2. An administrator configures a static route to 192.168.2.0/24 with next-hop 10.0.0.1. The route does not appear in the routing table. What is the most likely cause?
easy- ✓ A.The next-hop 10.0.0.1 is not reachable.
- B.The static route has a higher preference than an existing dynamic route.
- C.The configuration was not committed.
- D.The prefix 192.168.2.0/24 already exists in the forwarding table.
Why A: A static route will only be installed in the routing table if the next-hop address is reachable via an active route in the routing table. If 10.0.0.1 is not reachable (e.g., no route to that subnet, or the interface is down), Junos will reject the static route and not place it in the inet.0 table. This is a fundamental validation check in Junos that prevents black-hole routing.
Variation 3. A network administrator configures the following: `set routing-options static route 0.0.0.0/0 next-hop 192.168.1.1`. After committing, the administrator notices that the default route is not active. What could be the reason?
medium- A.The route preference is set to 170.
- B.The route is not exported into the forwarding table.
- ✓ C.The next-hop 192.168.1.1 is not reachable.
- D.The router already has a default route learned via DHCP.
Why C: A static route becomes active only if the next-hop address is reachable via a directly connected interface or another active route. If 192.168.1.1 is not reachable (e.g., no ARP entry, interface down, or no matching subnet), the route remains hidden (inactive) in the routing table. Junos verifies next-hop reachability before installing a static route into the forwarding table.
Variation 4. A static route is configured with next-hop 10.0.0.1, but the route does not appear in the routing table. The interface ge-0/0/0 has IP 192.168.1.2/24 and is up. What is the most likely reason?
medium- A.The static route has a preference of 5.
- B.The route is hidden due to an import policy.
- C.The static route is configured with the 'discard' option.
- ✓ D.The next-hop IP is not on a directly connected subnet.
Why D: D is correct because Junos requires the next-hop IP of a static route to be reachable via a directly connected subnet for the route to be installed in the routing table. Since the next-hop 10.0.0.1 is not on the same subnet as the interface ge-0/0/0 (192.168.1.2/24), the route remains hidden and does not appear in the routing table.
Keep practising
More JNCIA-JUNOS practice questions
- A junior engineer needs to collect a snapshot of the current system state, including routing tables, interfaces, and con…
- A network engineer is troubleshooting a connectivity issue and wants to see the active routes in the routing table. Whic…
- You are the network engineer for a mid-sized enterprise with a Juniper MX router running Junos. The router has two uplin…
- Which TWO attributes are used by Junos to select the active route among multiple routes to the same destination?
- What is the default preference of a direct route in Junos?
- A router has two routes to the same destination: one with preference 10 and metric 5, and another with preference 15 and…
Last reviewed: Jun 24, 2026
This JNCIA-JUNOS practice question is part of Courseiva's free Juniper Networks certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the JNCIA-JUNOS exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.