PAN OS Networking Configuration

Which of these is a valid way to define a source IP in a policy?

Which THREE items are defined in an IKE Crypto Profile?

What is the purpose of 'Path Monitoring' in HA?

How can you verify the status of a tunnel interface?

In GlobalProtect, what is the 'Portal' vs. 'Gateway'?

In a Site-to-Site VPN, which setting determines how the firewall handles traffic that does not match the phase 2 selector?

What is the purpose of an 'Aggregate Ethernet' interface?

Which TWO interface types support IP addresses?

Which THREE settings are configured in a Layer 3 interface?

What is the default behavior when a firewall is configured for HA but the control link fails?

What happens if a zone is not assigned to an interface?

Which object defines the encryption settings for a Site-to-Site VPN?

Which TWO issues can prevent BGP from reaching the 'Established' state?

Which TWO items must match for an OSPF adjacency to form?

When configuring an interface for DHCP client, where do you set this?

Which THREE items can be assigned to a Security Zone?

A administrator is configuring a VPN. What does the 'Local IP' in the IKE Gateway represent?

You are configuring a virtual wire interface. Which setting is required to ensure that traffic is passed between the two interfaces?

What is the primary function of a Virtual Router?

Which THREE routing protocols can be configured on a PAN-OS virtual router?

How does the firewall determine which virtual router to use for a packet?

When using OSPF, what is the 'Router ID' used for?

What is a 'Layer 3' interface in PAN-OS?

Which component is required to enable a firewall to act as an OSPF Area Border Router (ABR)?

How do you add a new interface to an existing zone?

What is the benefit of using a Loopback interface for a GlobalProtect portal?

When configuring OSPF on a PAN-OS firewall, what is the impact of setting the dead interval to a value different from the neighbor?

Why might OSPF adjacency stay in 'ExStart/Exchange' state?

You are troubleshooting GlobalProtect and notice the client cannot reach internal resources. Which routing issue is most likely?

Which TWO settings are configured in a Virtual Router?

A administrator needs to route traffic to an internal network via a tunnel. Where is the static route configured?

Where do you configure the tunnel interface IP address in a Site-to-Site VPN setup?

In BGP, which attribute is used to influence the path selection for outgoing traffic?

Which TWO conditions can trigger an HA failover?

Which TWO factors contribute to a successful BGP peer establishment?

Which option is required to use an interface in a security policy?

When troubleshooting a BGP route that is not appearing in the routing table, which command provides the most insight?

A administrator needs to allow traffic between two zones using a specific sub-interface. Which configuration step is mandatory?

Where do you configure the 'Heartbeat' interval for HA?

Which THREE components are involved in a VPN tunnel setup?

What is the purpose of an Aggregate Ethernet (AE) interface?

Which TWO methods are used to troubleshoot GlobalProtect connectivity issues?

Which object type is required to enable GlobalProtect access for remote users?

You are configuring a BGP peer. The connection stays in 'Active' state. What is the most likely cause?

A client is receiving a 'Gateway not reachable' error in GlobalProtect. What is a common troubleshooting step?

Which TWO components are involved in configuring GlobalProtect?

Which TWO commands are useful for troubleshooting OSPF?

What is the purpose of a Security Zone?

How do you delete a security policy rule?

Which TWO types of failover can be configured in HA?

Which THREE factors can affect the speed/throughput of a VPN tunnel?

What is the purpose of an HA Control Link?

In BGP, what is a 'Route Map' used for?

Which THREE items are required to configure a Site-to-Site VPN?

Why might a static route not be visible in the routing table?

Which interface type is used to manage the firewall over the network?

Which TWO interface modes are commonly used to segment traffic?

In an HA active/passive configuration, which mechanism ensures the passive firewall is ready to take over traffic?

Which setting in a Security Policy rule determines whether traffic is permitted or denied?

Which THREE things must be configured to allow HA between two firewalls?

Which TWO items must be configured to allow external management access?

An administrator wants to permit traffic between two sub-interfaces on the same physical port. What is required?

Which command confirms that an OSPF neighbor relationship is in the 'Full' state?

Which TWO actions must be performed to successfully configure a zone protection profile on a zone?

What is the effect of changing the HA heartbeat interval?

What happens to established sessions during an HA failover?

What is the function of a 'Tap' mode interface?

Which TWO protocols can be used to manage the firewall?

In HA, what is the difference between 'Active/Passive' and 'Active/Active' modes?

When configuring HA, what is 'Preemption'?

Which tab is used to configure physical interface settings like speed and duplex?

Which THREE items can be used as a 'Source' in a security policy?

When configuring a Static Route, what does the 'Metric' field do?