The answer is that the BGP session is established and the neighbor is advertising one prefix. This is correct because the `show bgp neighbors 10.1.12.2 received-routes` command displays only the routes that have been explicitly received from that specific neighbor, before any inbound policy is applied; the output confirms a single prefix `10.2.2.0/24` marked as valid and best, which directly proves the TCP connection and BGP session are up and exchanging updates. On the Cisco CCNP ENARSI 300-410 exam, this command tests your ability to differentiate between `received-routes` (pre-policy), `advertised-routes` (post-outbound policy), and `routes` (the BGP table after inbound policy), with a common trap being that `received-routes` will show nothing if the `soft-reconfiguration inbound` command is not configured. A useful memory tip is to think of “received” as the raw, unfiltered gift from the neighbor, while “routes” is what you keep after checking the policy wrapping.
300-410 BGP Troubleshooting Practice Question
This 300-410 practice question tests your understanding of bgp troubleshooting. Examine the command output carefully: the correct answer depends on what the output actually shows, not on general recall alone. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
A network engineer runs the following command on Router R1:
R1# show bgp neighbors 10.1.12.2 received-routes
BGP table version is 15, local router ID is 10.1.1.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 10.2.2.0/24 10.1.12.2 0 0 65002 i
Total number of prefixes 1
Based on this output, what can be inferred about the BGP session?
Clue words in this question
Noticing these words before you look at the options changes how you read each choice.
Clue: "best"
Why it matters: Signals that multiple options may be partially correct. Choose the option that most directly solves the exact problem described, not the one that sounds most complete.
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
The BGP session is established and the neighbor is advertising one prefix.
The output shows that R1 has received one prefix (10.2.2.0/24) from neighbor 10.1.12.2. The prefix is valid and best. This indicates the BGP session is established and exchanging routes.
Key principle: OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
✗
The BGP session is not established.
Why it's wrong here
If the session were not established, no routes would be received.
✓
The BGP session is established and the neighbor is advertising one prefix.
Why this is correct
The presence of a received route indicates the session is up and the neighbor is sending prefixes.
Clue confirmation
The clue word "best" in the question point toward this answer.
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Trap categories for this question
Command / output trap
Active state would show no received routes.
Detailed technical explanation
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
OSPF neighbours must agree on key parameters.
Router ID selection can affect neighbour relationships and LSDB output.
OSPF cost influences the preferred path.
A route can appear in OSPF information but not become the installed route.
TExam Day Tips
→Check area mismatch first when OSPF adjacency fails.
→Review passive interfaces when a network is advertised but no neighbour forms.
→Use show ip ospf neighbor and show ip route clues carefully.
Key takeaway
OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Real-world example
How this comes up in practice
A network engineer at a university connects two campus buildings via a fibre link. Both routers run OSPF, but no adjacency forms — even though both routers can ping each other. The engineer finds one router is in area 0 and the other in area 1. OSPF adjacency requires matching area numbers, hello/dead timers, and network type. IP reachability alone is not enough.
Related glossary terms
Concepts from this question explained
These glossary pages explain the core terms tested in this 300-410 question in full detail.
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related 300-410 OSPF questions on adjacency and route selection.
BGP Troubleshooting — This question tests BGP Troubleshooting — OSPF neighbours must agree on key parameters..
What is the correct answer to this question?
The correct answer is: The BGP session is established and the neighbor is advertising one prefix. — The output shows that R1 has received one prefix (10.2.2.0/24) from neighbor 10.1.12.2. The prefix is valid and best. This indicates the BGP session is established and exchanging routes.
What should I do if I get this 300-410 question wrong?
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related 300-410 OSPF questions on adjacency and route selection.
Are there clue words in this question I should notice?
Yes — watch for: "best". Signals that multiple options may be partially correct. Choose the option that most directly solves the exact problem described, not the one that sounds most complete.
What is the key concept behind this question?
OSPF neighbours must agree on key parameters.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
This 300-410 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 300-410 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.