300-410 Embedded Event Manager (EEM) Practice Question
This 300-410 practice question tests your understanding of embedded event manager (eem). Examine the command output carefully: the correct answer depends on what the output actually shows, not on general recall alone. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
A network engineer runs the following command on Router R1:
R1# show event manager policy registered
No. Type Time Created Name
1 applet 00:01:23 UTC Mar 1 2025 EIGRP_Neighbor_Down
2 applet 00:01:23 UTC Mar 1 2025 OSPF_Neighbor_Flap
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
Two EEM applet policies are registered and active.
The 'show event manager policy registered' command lists all EEM policies registered on the device. The output shows two applet policies registered, but no trigger events are shown. The correct answer is that two EEM applet policies are registered, but the output does not indicate whether they are enabled or disabled; registration means they are loaded and ready to trigger.
Key principle: OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
✓
Two EEM applet policies are registered and active.
Why this is correct
The output shows two applet policies registered, meaning they are loaded and ready to trigger based on their defined events.
Two EEM applet policies are registered but disabled.
Why it's wrong here
The output does not show any disabled status; registration implies they are active unless explicitly disabled.
✗
Only one EEM applet policy is registered.
Why it's wrong here
The output clearly lists two policies: EIGRP_Neighbor_Down and OSPF_Neighbor_Flap.
✗
The EEM applet policies are triggered by syslog events.
Why it's wrong here
The output does not show the trigger events; it only lists the policy names and registration time.
Common exam traps
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Trap categories for this question
Command / output trap
The output does not show any disabled status; registration implies they are active unless explicitly disabled.
Detailed technical explanation
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
OSPF neighbours must agree on key parameters.
Router ID selection can affect neighbour relationships and LSDB output.
OSPF cost influences the preferred path.
A route can appear in OSPF information but not become the installed route.
TExam Day Tips
→Check area mismatch first when OSPF adjacency fails.
→Review passive interfaces when a network is advertised but no neighbour forms.
→Use show ip ospf neighbor and show ip route clues carefully.
Key takeaway
OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Real-world example
How this comes up in practice
A network engineer at a university connects two campus buildings via a fibre link. Both routers run OSPF, but no adjacency forms — even though both routers can ping each other. The engineer finds one router is in area 0 and the other in area 1. OSPF adjacency requires matching area numbers, hello/dead timers, and network type. IP reachability alone is not enough.
Related glossary terms
Concepts from this question explained
These glossary pages explain the core terms tested in this 300-410 question in full detail.
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related 300-410 OSPF questions on adjacency and route selection.
Embedded Event Manager (EEM) — This question tests Embedded Event Manager (EEM) — OSPF neighbours must agree on key parameters..
What is the correct answer to this question?
The correct answer is: Two EEM applet policies are registered and active. — The 'show event manager policy registered' command lists all EEM policies registered on the device. The output shows two applet policies registered, but no trigger events are shown. The correct answer is that two EEM applet policies are registered, but the output does not indicate whether they are enabled or disabled; registration means they are loaded and ready to trigger.
What should I do if I get this 300-410 question wrong?
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related 300-410 OSPF questions on adjacency and route selection.
What is the key concept behind this question?
OSPF neighbours must agree on key parameters.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
This 300-410 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 300-410 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.