- A
Three
Why wrong: Unnecessary; two suffices.
- B
Two
Two port channels allow each controller to connect to both switches.
- C
One
Why wrong: One port channel would connect only one controller to only one switch.
- D
Four
Why wrong: Overkill; two is sufficient for redundancy.
350-601 Storage Network Practice Question
This 350-601 practice question tests your understanding of storage network. Read the scenario carefully and evaluate each option against the stated constraints before committing to an answer. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
An engineer needs to design a resilient Fibre Channel SAN that eliminates single points of failure between two MDS switches and a storage array with two controllers. What is the minimum number of FC port channels required to achieve this goal?
Clue words in this question
Noticing these words before you look at the options changes how you read each choice.
Clue:
"minimum / minimize"Why it matters: Asks for the least resource use — fewest addresses, smallest subnet, lowest overhead. Eliminate over-provisioned options even if they would technically work.
Answer choices
Why each option matters
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
Two
For redundancy, each storage controller connects to both switches. Two port channels (each from a controller to a switch) are needed. Option A (1) provides only one link per controller. Option C (3) and D (4) are overkill. Option B is correct.
Key principle: NAT direction and interface roles matter as much as the IP address mapping. Inside/outside designation controls which traffic is translated.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
- ✗
Three
Why it's wrong here
Unnecessary; two suffices.
- ✓
Two
Why this is correct
Two port channels allow each controller to connect to both switches.
Clue confirmation
The clue word "minimum / minimize" in the question point toward this answer.
Related concept
Static NAT maps one inside address to one outside address.
- ✗
One
Why it's wrong here
One port channel would connect only one controller to only one switch.
- ✗
Four
Why it's wrong here
Overkill; two is sufficient for redundancy.
Common exam traps
Common exam trap: NAT rules depend on direction and matching traffic
NAT is not only about the public address. The inside/outside interface roles and the ACL or rule that matches traffic are just as important.
Detailed technical explanation
How to think about this question
NAT questions usually test address translation, overload/PAT behaviour, static mappings and whether the right traffic is being translated. Read the interface direction and address terms carefully.
KKey Concepts to Remember
- Static NAT maps one inside address to one outside address.
- PAT allows many inside hosts to share one public address using ports.
- Inside local and inside global describe the private and translated addresses.
- NAT ACLs identify traffic for translation, not always security filtering.
TExam Day Tips
- Identify inside and outside interfaces first.
- Check whether the scenario needs static NAT, dynamic NAT or PAT.
- Do not confuse NAT matching ACLs with normal packet-filtering intent.
Key takeaway
NAT direction and interface roles matter as much as the IP address mapping. Inside/outside designation controls which traffic is translated.
Real-world example
How this comes up in practice
A small business has 20 workstations on the 192.168.1.0/24 network and one public IP from its ISP. The router uses PAT (NAT overload) so all 20 devices share one public address using different source ports. NAT questions test whether you understand the four address terms and which direction each translation applies.
What to study next
Got this wrong? Here's your next step.
Review the four NAT address types (inside local, inside global, outside local, outside global), PAT port overload, and static vs dynamic NAT use cases. Then practise related 350-601 NAT questions on configuration and troubleshooting.
- →
Storage Network — study guide chapter
Learn the concepts, then practise the questions
- →
Storage Network practice questions
Targeted practice on this topic area only
- →
All 350-601 questions
500 questions across all exam domains
- →
Cisco DCCOR / CCNP Data Center Core 350-601 study guide
Full concept coverage aligned to exam objectives
- →
350-601 practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related 350-601 practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
Network practice questions
Practise 350-601 questions linked to Network.
Compute practice questions
Practise 350-601 questions linked to Compute.
Storage Network practice questions
Practise 350-601 questions linked to Storage Network.
Automation practice questions
Practise 350-601 questions linked to Automation.
Security practice questions
Practise 350-601 questions linked to Security.
350-601 fundamentals practice questions
Practise 350-601 questions linked to 350-601 fundamentals.
350-601 scenario practice questions
Practise 350-601 questions linked to 350-601 scenario.
350-601 troubleshooting practice questions
Practise 350-601 questions linked to 350-601 troubleshooting.
Practice this exam
Start a free 350-601 practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this 350-601 question test?
Storage Network — This question tests Storage Network — Static NAT maps one inside address to one outside address..
What is the correct answer to this question?
The correct answer is: Two — For redundancy, each storage controller connects to both switches. Two port channels (each from a controller to a switch) are needed. Option A (1) provides only one link per controller. Option C (3) and D (4) are overkill. Option B is correct.
What should I do if I get this 350-601 question wrong?
Review the four NAT address types (inside local, inside global, outside local, outside global), PAT port overload, and static vs dynamic NAT use cases. Then practise related 350-601 NAT questions on configuration and troubleshooting.
Are there clue words in this question I should notice?
Yes — watch for: "minimum / minimize". Asks for the least resource use — fewest addresses, smallest subnet, lowest overhead. Eliminate over-provisioned options even if they would technically work.
What is the key concept behind this question?
Static NAT maps one inside address to one outside address.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Last reviewed: Jun 24, 2026
This 350-601 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 350-601 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.