350-601 Practice Question: An engineer is configuring Fibre Channel…
This 350-601 practice question tests your understanding of an engineer is configuring fibre channel…. Read the scenario carefully and evaluate each option against the stated constraints before committing to an answer. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
An engineer is configuring Fibre Channel PortChannels on a Cisco MDS switch. Which statement about Fibre Channel PortChannels is true?
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
They load-balance based on the source and destination WWPNs.
Fibre Channel PortChannels require all member ports to be of the same type (e.g., all E-ports). They load-balance across links and are compatible with VSAN trunking. They do not require the same speed on all ports, but it is recommended.
Key principle: A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
✗
They require all member ports to be on the same VSAN.
Why it's wrong here
PortChannels can carry multiple VSANs if configured as trunk ports.
✗
They can include both E-ports and F-ports in the same PortChannel.
Why it's wrong here
All ports must be the same type (e.g., all E-ports).
✓
They load-balance based on the source and destination WWPNs.
Why this is correct
Fibre Channel PortChannels use a hash of source and destination IDs (WWPNs) for load balancing.
Related concept
Access ports place end devices into a single VLAN.
✗
They are supported only in NPV mode.
Why it's wrong here
PortChannels are used in standard FC fabric, not exclusive to NPV.
Common exam traps
Common exam trap: an active trunk can still block the VLAN you need
A trunk being up does not prove every VLAN is crossing it. Check allowed VLAN lists, native VLAN mismatch, VLAN existence and access-port assignment.
Detailed technical explanation
How to think about this question
VLAN questions usually combine access-port and trunking clues. The key is to identify whether the issue is local to one switchport, caused by the trunk, or caused by the VLAN not existing where it needs to exist.
KKey Concepts to Remember
Access ports place end devices into a single VLAN.
Trunk ports carry multiple VLANs between switches.
Allowed VLAN lists decide which VLANs can cross a trunk.
Native VLAN mismatch can create confusing symptoms.
TExam Day Tips
→Use show vlan brief to verify access VLANs.
→Use show interfaces trunk to verify trunk state and allowed VLANs.
→Do not treat every same-VLAN issue as a routing problem.
Key takeaway
A trunk being up does not mean the VLAN is allowed across it. Always verify the allowed VLAN list and whether the VLAN exists on both switches.
Real-world example
How this comes up in practice
A help-desk technician troubleshoots why a newly connected PC cannot reach shared printers on the same floor. The cable is good, the switch port is active, but the PC is in VLAN 20 and the printers are in VLAN 10. The uplink trunk only allows VLAN 10. A trunk being up does not mean every VLAN crosses it.
What to study next
Got this wrong? Here's your next step.
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related 350-601 questions on switching, trunking, and access-port configuration.
Access ports place end devices into a single VLAN.
What is the correct answer to this question?
The correct answer is: They load-balance based on the source and destination WWPNs. — Fibre Channel PortChannels require all member ports to be of the same type (e.g., all E-ports). They load-balance across links and are compatible with VSAN trunking. They do not require the same speed on all ports, but it is recommended.
What should I do if I get this 350-601 question wrong?
Review VLAN allowed lists, native VLAN mismatch detection, and how to verify VLAN membership with show vlan brief and show interfaces trunk. Then practise related 350-601 questions on switching, trunking, and access-port configuration.
What is the key concept behind this question?
Access ports place end devices into a single VLAN.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
This 350-601 practice question is part of Courseiva's free Cisco certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the 350-601 exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.