VCP-DCV vSphere Lifecycle Management Practice Test 1 — 15 Questions

Question 1

An administrator is using vLCM to manage a cluster with 4 ESXi hosts. After a remediation, two hosts show a compliance status of 'Non-Compliant' with the message 'Firmware is not compatible with the selected image'. What is the most likely cause?

Choose an answer to begin — your selection is scored in the full session.

Accepted Answer

The cluster does not have a Hardware Support Manager configured.. VLCM relies on a Hardware Support Manager (HSM) to validate firmware compatibility against the selected ESXi image. Without an HSM configured, vLCM cannot check firmware versions, so it flags hosts as 'Non-Compliant' with the message 'Firmware is not compatible with the selected image' even if the firmware is actually compatible. This is a common misconfiguration when using vLCM with vSAN or other hardware-dependent clusters.

Answer

The selected image includes a firmware component that is not compatible with the hosts.

Answer

The firmware update requires a different ESXi version and was skipped.

Answer

The hosts were put into maintenance mode during remediation and autopassivation failed.

Question 2

An administrator is troubleshooting a vLCM cluster where a host fails to remediate with the error: 'Host does not meet the requirements of the selected image'. The host is running ESXi 7.0 U3 and the desired image is ESXi 8.0 U1. What should the administrator check first?

Accepted Answer

Verify that the host is in maintenance mode before remediation.. VLCM requires the host to be in maintenance mode before applying a new image, especially when upgrading across major ESXi versions (e.g., 7.0 U3 to 8.0 U1). The error 'Host does not meet the requirements of the selected image' typically occurs when the host is not in maintenance mode, as vLCM cannot stage or reboot the host to apply the new image while VMs are running. Placing the host in maintenance mode ensures that all VMs are migrated or powered off, allowing the remediation process to proceed without disruption.

Answer

Verify that all VIBs in the image are compatible with ESXi 7.0 U3.

Answer

Ensure that the host has internet access to download the image.

Answer

Check that the vCenter Server version is at least 8.0.

Question 3

An administrator has a vLCM-managed cluster with a desired image that includes a custom VIB from a third party. After remediation, one host shows 'Compliant' but the custom VIB is missing. What is the most likely cause?

Accepted Answer

The custom VIB was not included in the baseline.. If the desired image in vLCM actually includes the custom VIB, the host would be non-compliant if the VIB is missing. Therefore, the most likely cause is that the administrator mistakenly believes the VIB was included, but it was not part of the desired image. This results in a compliant host without the VIB.

Answer

The host has a host profile that overrides the vLCM image.

Answer

The host's acceptance level is set to 'CommunitySupported' but the VIB requires 'PartnerSupported'.

Answer

The custom VIB is not available in the VMware online depot.

Question 4

A vSphere administrator is using vLCM and needs to ensure that all hosts are compliant with the desired image. Which TWO actions are valid when remediating a vLCM cluster?

Accepted Answer

Perform a pre-remediation check to validate the image.. Option A is correct because vLCM provides a pre-remediation check (the "Pre-check" / "Check Compliance" step) that validates the desired image against each host—verifying hardware compatibility, firmware/HCL, and driver/software dependencies—before any remediation begins, allowing the administrator to catch issues that would otherwise fail the remediation. Option D is correct because vLCM remediation supports Quick Boot, which skips the full BIOS/POST and hardware initialization by rebooting directly into the new ESXi image, dramatically reducing reboot time and thus cluster remediation downtime. Option B is incorrect because remediating a vLCM cluster requires hosts to enter maintenance mode (or be in a state where they can be evacuated), so remediation cannot proceed without maintenance mode. Option C is incorrect because vLCM remediates the cluster as a whole against the desired image; you do not selectively remediate only non-compliant hosts as a supported remediation action. Option E is incorrect because vLCM blocks remediation when there are unresolved compliance issues—the image must be validated and compliant before remediation can proceed.

Answer

Remediate without putting hosts into maintenance mode.

Answer

Remediate only hosts that are non-compliant.

Answer

Remediate the cluster even if there are compliance issues.

Question 5

An administrator is troubleshooting a vLCM cluster where remediation fails with 'Host cannot be updated due to missing VIB'. The desired image includes the VIB. Which THREE actions should the administrator take?

Accepted Answer

Verify that the software depot URL is accessible from vCenter.. Option A is correct because vLCM remediation pulls the desired image's VIBs from the configured software depot, so if the depot URL is unreachable from vCenter, the VIB cannot be downloaded and the host reports it as missing. Option C is correct because each VIB has an acceptance level (VMwareCertified, VMwareAccepted, PartnerSupported, CommunitySupported), and if the host's acceptance level is stricter than the VIB's, the VIB is rejected and remediation fails. Option D is correct because an existing installed VIB that conflicts with the desired image's VIB (same name but different version, or a dependency clash) prevents the new VIB from being applied, producing the missing-VIB error. Option B is not relevant because firmware version does not cause a VIB to be reported as missing during image remediation. Option E is not relevant because vLCM uses desired-state images rather than legacy baselines, so a conflicting baseline is not part of this workflow.

Answer

Ensure that the host firmware is up to date.

Answer

Check if a baseline is attached that conflicts.

Question 6

An administrator sees the above JSON output from a vLCM compliance report. What should the administrator do to resolve the compliance issue?

Accepted Answer

Verify that the custom-vib is available in the depot and that esxi-02 can install it.. The JSON output indicates that a custom VIB is present on esxi-01 but missing from esxi-02, causing a compliance mismatch. Option B is correct because the administrator must first verify that the custom VIB is available in the configured depot and that esxi-02 can install it, as vLCM uses depot-based image specifications and any missing VIB must be reachable and installable from the depot to achieve compliance.

Answer

Add the custom-vib to the desired image.

Answer

Update the firmware version for esxi-02.

Answer

Re-define the desired image for the cluster.

Question 7

A company has a vSphere cluster with 8 ESXi 7.0 U3 hosts managed by vCenter Server 7.0 U3. The administrator wants to upgrade the cluster to ESXi 8.0 U1 using vLCM. The administrator has already upgraded the vCenter Server to 8.0 U1 and enabled vLCM on the cluster. The desired image is set to ESXi 8.0 U1 with no additional VIBs. However, when attempting to remediate, the first host fails with error: 'Failed to remediate host: The host does not support the selected image'. The other hosts are still pending. The administrator checks the host hardware and confirms it is on the HCL for ESXi 8.0. What is the most likely cause?

Accepted Answer

The host firmware is not compatible with the desired image and HSM is not configured.. The error 'The host does not support the selected image' typically indicates a hardware compatibility issue that vLCM cannot resolve without Hardware Support Manager (HSM) configured. Even if the host is on the HCL, the firmware version may not meet the requirements for ESXi 8.0 U1, and vLCM uses HSM to validate and remediate firmware as part of the image compliance process. Without HSM, vLCM cannot ensure the firmware is compatible, leading to the remediation failure.

Answer

The host was not put into maintenance mode before remediation.

Answer

The host was already upgraded to ESXi 8.0 U1, causing a conflict.

Answer

The vCenter Server version is not compatible with the host.

Question 8

An organization has a vLCM-managed cluster with 5 ESXi 8.0 hosts. The desired image includes ESXi 8.0 U1 and a specific third-party storage driver VIB. The administrator recently updated the desired image to a new version of the storage driver. After remediation, three hosts show 'Compliant' but two hosts show 'Non-Compliant' with the error: 'VIB missing: storage-driver-vib'. The administrator confirms that the VIB is present in the image and that the hosts were recently added to the cluster. What is the most likely cause of the non-compliance on the two hosts?

Accepted Answer

The two hosts have a host acceptance level set to 'CommunitySupported' while the VIB requires 'PartnerSupported'.. When a host is added to a vLCM-managed cluster, the desired image is applied to it. If the host's acceptance level (e.g., 'CommunitySupported') is lower than the VIB's required acceptance level (e.g., 'PartnerSupported'), vLCM will refuse to install the VIB, causing a 'Non-Compliant' status with a 'VIB missing' error. This is a common issue when hosts are imported from environments with relaxed acceptance policies.

Answer

The two hosts have incompatible firmware for the storage driver.

Answer

The VIB was not included in the image for those hosts.

Answer

The vCenter Server cannot reach the software depot for those hosts.

Question 9

A company is planning to upgrade vCenter Server from 7.0 to 8.0 and then upgrade ESXi hosts from 7.0 Update 2 to 8.0. They have a vSAN cluster and use vSphere Lifecycle Manager (vLCM) with a single image. What is a critical prerequisite that must be verified before starting the vCenter Server upgrade?

Accepted Answer

The vCenter Server version must be equal to or higher than the ESXi version being managed.. VCenter Server must be at a version equal to or higher than the ESXi hosts it manages. When upgrading from vCenter 7.0 to 8.0, the vCenter upgrade must complete first, as it will then be able to manage the ESXi 7.0 hosts during their subsequent upgrade to 8.0. Attempting to upgrade ESXi hosts before vCenter would violate this compatibility requirement and could cause management communication failures.

Answer

The vSAN cluster must be turned off to avoid data loss.

Answer

All ESXi hosts must be updated to the latest ESXi 7.0 patch before upgrading vCenter.

Answer

vSphere Update Manager (VUM) must be installed and configured.

Question 10

An administrator is using vLCM to manage a cluster with 4 ESXi hosts. After a remediation, two hosts show a compliance status of 'Non-Compliant' with the message 'Firmware is not compatible with the selected image'. What is the most likely cause?

Choose an answer to begin — your selection is scored in the full session.

Accepted Answer

Place the host into maintenance mode to evacuate VMs before remediation.. VLCM requires the host to be in maintenance mode before remediation to free up memory resources for the update process. The error 'Host does not have sufficient memory to perform remediation' indicates that running VMs are consuming memory that is needed for the remediation operation. Placing the host into maintenance mode evacuates all VMs, releasing memory and allowing the remediation to proceed.

Answer

Use the 'Force Remediate' option in vLCM to bypass the check.

Answer

Increase the physical memory of the host.

Answer

Reboot the host to free up memory.

Question 11

Which TWO statements are true regarding vSphere Lifecycle Manager (vLCM) clusters? (Choose two.)

Accepted Answer

vLCM can manage vSAN clusters using a single image.. Option A is correct because vSphere Lifecycle Manager can manage vSAN clusters with a single desired-state image, and vLCM is in fact the recommended way to keep vSAN hosts consistent since the image includes the vSAN ESXi base image and firmware/driver add-ons. Option E is correct because vLCM supports two cluster management models: the newer single image (declarative, image-based) approach and the legacy baseline-based approach, and a cluster can be managed by either one, though not both simultaneously. Options B, C, and D are not correct: vLCM does not require identical hardware (it works across heterogeneous hosts as long as the image components are compatible), it can remediate standalone hosts as well as cluster members, and it does not require vCenter Server Enhanced Linked Mode.

Answer

vLCM only supports clusters with identical hardware.

Answer

vLCM can only remediate hosts that are part of a cluster.

Answer

vLCM requires vCenter Server to be in Enhanced Linked Mode.

Question 12

A global company manages multiple vSphere clusters across different data centers. They have a standard operating procedure to upgrade ESXi hosts every two years. The vSphere administrator is planning the upgrade of a critical production cluster that runs a mix of VMs, including some latency-sensitive applications. The cluster consists of 20 ESXi 7.0 Update 3 hosts managed by vLCM with a single image. The target is ESXi 8.0 Update 1. The administrator wants to minimize downtime and ensure rollback capability. The company has a hardware support manager (HSM) integrated with vLCM. After staging the new image, the administrator remediates the cluster. During the remediation of the first host, the host fails to reboot after applying the image and becomes unresponsive. What is the most likely cause of this failure?

Accepted Answer

The hardware support manager (HSM) did not deploy the correct firmware version for the host.. The most likely cause is that the hardware support manager (HSM) deployed an incorrect firmware version for the host during the vLCM remediation. vLCM integrates with HSM to automatically update firmware as part of the image-based lifecycle, and if the firmware is incompatible with ESXi 8.0 Update 1, the host can fail to reboot and become unresponsive. This is a known risk when upgrading across major ESXi versions, as hardware firmware requirements often change.

Answer

The vCenter Server version is not compatible with ESXi 8.0 Update 1.

Answer

The host was not placed in maintenance mode before remediation.

Answer

The vLCM single image is corrupted and was applied incorrectly.

Question 13

An administrator is troubleshooting a vLCM cluster that has multiple ESXi hosts with non-compliant status. The cluster uses a single image with an HSM for firmware. Which TWO actions should the administrator take to identify the root cause of non-compliance? (Choose two.)

Accepted Answer

Verify the HSM is properly connected and reporting firmware inventory.. The Hardware Support Manager (HSM) is responsible for reporting firmware inventory to vLCM. If the HSM is not properly connected or is failing to report, vLCM cannot determine the current firmware state of the hosts, leading to non-compliant status. Verifying the HSM connection and inventory reporting is a critical first step in isolating the root cause.

Answer

Validate the cluster image against the desired image specification.

Answer

Run the vSphere Update Manager baseline scan on each host.

Answer

Check the baseline compliance report for the cluster.

Question 14

A company manages a vSphere 8 cluster with vLCM enabled. The administrator needs to remediate the cluster to apply a security patch. What should the administrator do to minimize performance impact on running workloads?

Accepted Answer

Enable Quick Boot in the cluster image configuration.. Quick Boot in vSphere Lifecycle Manager (vLCM) significantly reduces host reboot time by skipping hardware initialization steps during remediation. This minimizes downtime and performance impact on running workloads because hosts rejoin the cluster faster. Other options either do not directly reduce reboot impact or are incorrect approaches.

Answer

Use vSphere Live Migration to move workloads before remediation.

Answer

Use legacy baselines instead of vLCM to allow rolling updates.

Answer

Disable Distributed Power Management (DPM) to prevent hosts from powering off during remediation.

Question 15

An administrator checks the compliance status of a vLCM-managed cluster and sees that several hosts are marked as non-compliant even though the cluster image has not been changed recently. The hosts are currently running a version that matches the cluster image. What is the most likely cause of this non-compliance?

Accepted Answer

The compliance cache is outdated; a manual rescan is needed.. vLCM compliance status is based on a cached scan of the host's current state against the cluster image. If the cluster image has not changed and the hosts match it, but they still show non-compliant, the most likely cause is that the compliance cache is stale and a manual rescan is required to refresh the status. This is a common operational quirk in vLCM.

Answer

A new baseline was created and applied to the hosts.

Answer

VMware Tools was upgraded on the hosts without updating the cluster image.

Answer

The cluster image was updated but the hosts were not remediated.