SK0-005 Practice Test 5 — 10 Questions

Question 1

A company is implementing a disaster recovery strategy for its on-premises VMware vSphere environment. The IT manager wants to ensure that virtual machines can be recovered at a secondary site within 4 hours of a primary site failure. The secondary site has identical hardware but no active VMs. The company has a limited budget and wants to minimize ongoing costs. Which of the following solutions BEST meets these requirements?

Accepted Answer

Use VMware vSphere Replication to replicate VMs to the secondary site and perform manual recovery when needed.. VMware vSphere Replication offers a cost-effective way to replicate VMs to a secondary site without requiring expensive storage arrays or SRM licensing. It supports manual recovery, which can meet a 4-hour RTO. Other options either incur high costs, rely on slow tape restoration, or require expensive network infrastructure. Therefore, vSphere Replication is the best fit.

Answer

Implement VMware Site Recovery Manager (SRM) with array-based replication and automated failover.

Answer

Set up a stretched vSphere cluster across both sites with synchronous replication.

Answer

Configure nightly backups to tape and transport them to the secondary site for restoration.

Question 2

A data center technician must install a new 1U server into a rack that already contains several servers drawing significant power. The rack's power distribution unit reports that the current load is near its rated capacity. Which of the following should the technician do first to avoid overloading the circuit?

Accepted Answer

Calculate the new server's power draw and verify the PDU has sufficient headroom before connecting. Before adding any load, the technician must quantify the new server's power requirement and confirm the PDU and its upstream circuit have enough spare capacity. Only after that calculation can the connection be made safely, possibly requiring a second circuit or PDU if headroom is insufficient.

Answer

Move one existing server's power supply to a different PDU without checking its load

Answer

Connect the new server's power supplies to the nearest available outlets on the existing PDU

Answer

Install the server and immediately enable power capping to reduce its draw

Question 3

A company is implementing a disaster recovery plan for its on-premises data center. The plan must include measures to ensure data integrity and availability during a site-wide power failure. Which two actions should be included in the plan? (Choose two.)

Accepted Answer

Deploy an uninterruptible power supply (UPS) for all critical servers and storage.. To ensure data integrity and availability during a site-wide power failure, a UPS provides immediate battery power for graceful shutdown or ride-through, while a generator with ATS supplies long-term power to keep systems operational. Together, they form a layered power protection strategy. Other options compromise data integrity or do not address power failure directly.

Answer

Schedule full backups to run only during business hours.

Answer

Enable write caching on all storage controllers without battery backup.

Answer

Configure RAID 0 on all database servers to improve performance.

Question 4

A security team is hardening a fleet of Linux web servers that will be exposed to the internet. They want to reduce the attack surface and limit the impact of a compromised service account. Which two actions BEST support these goals? (Choose two.)

Accepted Answer

Configure the firewall to allow only ports 80 and 443 from any source and deny all other inbound traffic by default.. Reducing attack surface means exposing only necessary ports and removing unnecessary services, while limiting impact means confining what a compromised process can do. A default-deny firewall with only web ports open and running the service as a restricted non-privileged account with minimal file access both serve those goals. Disabling mandatory access control, granting passwordless sudo, and exposing credentials all increase risk.

Answer

Store database credentials in a world-readable configuration file so all administrators can access them during outages.

Answer

Grant the web service account sudo rights with no password so administrators can troubleshoot quickly during incidents.

Answer

Disable SELinux or AppArmor on the servers so that application updates do not fail during deployment.

Question 5

A company has a Windows Server 2022 server that runs a custom application which writes heavily to a local SSD. The administrator notices that the SSD's wear-leveling indicator shows significant wear after only six months. The server logs show frequent small write operations. Which action should the administrator take to reduce SSD wear while maintaining performance?

Accepted Answer

Configure the application to batch small writes into larger sequential writes.. The most effective way to reduce SSD wear from frequent small writes is to batch them into larger sequential writes, which lowers write amplification. This maintains performance while extending the drive's lifespan. Moving logs within the same SSD or enabling write caching does not reduce the total bytes written, and disabling the page file introduces instability without addressing the application's write pattern.

Answer

Move the application's log files to a different volume on the same SSD.

Answer

Enable write caching on the SSD controller.

Answer

Disable the page file on the SSD.

Question 6

A server administrator notices that a production file server intermittently loses network connectivity for a few seconds, and users report dropped SMB sessions. The switch port shows no errors, and the server's NIC link LED stays solid. The administrator suspects a duplex mismatch. Which tool should the administrator use to verify the NIC's current speed and duplex settings on a Linux server?

Accepted Answer

ethtool. A duplex mismatch occurs when one side of a link is set to full-duplex and the other to half-duplex, leading to collisions, dropped packets, and intermittent connectivity without a complete link loss. The NIC's link LED remains solid because the physical link is up. The ethtool utility directly reports the negotiated duplex and speed, allowing the administrator to confirm whether the server NIC is operating at half-duplex while the switch port is full-duplex. Other tools show symptoms or unrelated configuration but not the duplex setting itself.

Answer

netstat -i

Answer

ip addr show

Answer

tcpdump

Question 7

A technician receives an urgent alert that a critical file server at a remote branch office has gone offline and is unreachable over the network. The server is accessible via out-of-band IPMI, which indicates that chassis power is present, but the power LED on the server is blinking amber instead of steady green. The IPMI system event log reports "System board voltage regulator failure" as the last critical event before the failure. Attempts to use the remote KVM show no video output, and Wake-on-LAN commands have no effect. The branch office has no on-site IT personnel; the only staff are general office workers with minimal technical training. The earliest a field technician can travel to the site is 48 hours. The main office has an identically configured spare server and a backup image of the file server's system disk. The branch office staff can follow simple plug-and-play instructions if provided. Which of the following is the BEST immediate course of action to restore the file services with minimal downtime?

Accepted Answer

Ship the spare server and a pre-configured backup image to the branch office for local staff to swap.. Given the voltage regulator failure on the system board, the server is not repairable remotely. Shipping the pre-configured spare server allows non-technical staff to swap the entire unit by following simple cabling instructions, restoring service quickly without waiting for a technician. Option A is correct because it minimizes downtime by leveraging available resources. Option B is incorrect because voltage regulator modules are rarely field-replaceable; they are integrated into the motherboard, and dispatching a technician would take 48 hours plus repair time. Option C is incorrect because reseating the power supply is unlikely to fix a system board voltage regulator fault, and could cause further confusion for untrained staff. Option D is incorrect because ordering a replacement board and waiting for a technician to install it would take even longer, extending downtime unnecessarily.

Answer

Order a replacement system board and express ship it to the branch for a technician to install later.

Answer

Instruct a non-technical employee at the branch to reseat the power supply and clear the error log.

Answer

Dispatch a technician with a replacement voltage regulator module for on-site repair.

Question 8

A RAID 5 array is degraded due to a failed disk. What is the best practice for recovery?

Accepted Answer

Replace the failed disk and allow the array to rebuild automatically. In a RAID 5 array, a single disk failure leaves the array degraded but still operational because parity data on the remaining disks can reconstruct the missing data. Best practice is to replace the failed disk and allow the controller to rebuild the array automatically from parity, restoring redundancy without downtime or data loss. This is the standard hot-swap recovery procedure and requires no backup restore because the data is still intact.

Answer

Replace the failed disk and restore from backup

Answer

Replace the failed disk and perform a manual rebuild from backup

Answer

Delete the logical drive and recreate the array

Question 9

A server hosts a database that requires nightly backups. The backup strategy uses a full backup every Sunday and differential backups on other days. On Wednesday, the server fails. Which backup sets are required to restore to the most recent state?

Accepted Answer

Last full backup and the latest differential backup. A differential backup contains all changes since the last full backup. Therefore, only the last full backup and the latest differential are needed for a restore. Incremental backups would require all incrementals since the last full, but the scenario uses differential backups.

Answer

Last full backup and all differential backups since Sunday

Answer

Last full backup only

Answer

Last full backup and all incremental backups since Sunday

Question 10

A server administrator is troubleshooting a RAID controller issue on a production server. The server has a hardware RAID 5 array with three drives. The administrator notices that one drive's status LED is solid amber, and the RAID controller management utility reports the array as degraded. The administrator has a replacement drive of the same model and capacity. Which action should the administrator take to restore the array to optimal status?

Accepted Answer

Hot-swap the failed drive with the replacement and allow the controller to automatically rebuild the array.. A degraded RAID 5 array with a failed drive should be restored by replacing the failed drive and allowing the controller to rebuild. Hot-swapping is supported on most server backplanes and minimizes downtime. Recreating the array or replacing all drives destroys data, and forcing a failed drive online does not address the hardware failure. The correct action is to replace the single failed drive and rebuild.

Answer

Shut down the server, replace the drive, and then recreate the RAID array from scratch.

Answer

Replace all three drives simultaneously to ensure compatibility and rebuild the array.

Answer

Run a consistency check on the array and mark the failed drive as online.