LPIC-2 Block Devices, Filesystems and Advanced Storage — Timed 10 Questions

Question 1

A system administrator notices that a new 1TB NVMe drive (/dev/nvme0n1) is not detected by the kernel. The hardware is confirmed working. Which troubleshooting step should be taken first to check if the drive is recognized by the system's PCI subsystem?

Accepted Answer

Run lspci to verify the NVMe controller is detected.. The NVMe drive is not detected by the kernel, but the hardware is confirmed working. The first step is to verify whether the PCI subsystem sees the NVMe controller, because NVMe devices are connected via the PCI Express bus. Running lspci lists all PCI devices, including the NVMe controller; if it does not appear, the issue is at the PCI or hardware level, not the block layer.

Answer

Run lsblk to list all block devices.

Answer

Check dmesg output for errors.

Answer

Run fdisk -l /dev/nvme0n1 to probe the drive.

Question 2

An administrator is designing a high-availability storage solution using DRBD. The requirement is to have two nodes with synchronous replication and automatic failover in case of primary node failure. Which configuration best achieves this?

Accepted Answer

DRBD in Primary/Primary mode managed by Pacemaker cluster stack.. Option D is correct because DRBD in Primary/Primary mode, managed by the Pacemaker cluster stack, provides synchronous replication and automatic failover. Pacemaker monitors node health and can promote the secondary node to primary automatically upon primary failure, meeting the high-availability requirement without manual intervention.

Answer

Export the DRBD block device via NFS and use a load balancer.

Answer

Primary/Secondary DRBD resource with manual failover using drbdadm.

Answer

DRBD with Heartbeat to automatically promote the secondary on primary failure.

Question 3

A filesystem is reported as 'read-only' after an unexpected power failure. Which command should be used to attempt repair without data loss?

Accepted Answer

fsck -n /dev/sda1. After an unexpected power failure, the filesystem may have been marked as needing a clean replay of its journal, but it is not necessarily corrupted. Running `fsck -n` performs a read-only check of the filesystem without making any changes, allowing you to assess the extent of damage or confirm that the journal replay is all that is needed. This avoids the risk of `fsck` making incorrect automatic repairs that could cause data loss, which is critical when the root cause is an unclean shutdown rather than structural corruption.

Answer

mount -o remount,rw /dev/sda1

Answer

fsck -y /dev/sda1

Answer

e2fsck -p /dev/sda1

Question 4

Which TWO statements about LVM thin provisioning are correct?

Accepted Answer

The filesystem on a thin volume must support the 'discard' option to free unused space.. Option B is correct because thin volumes allocate data blocks on demand from a thin pool. To allow the underlying physical storage to reclaim unused blocks when files are deleted, the filesystem must support the 'discard' option (or use fstrim) so that it can notify the device mapper of freed space. Without discard, the thin pool never learns that blocks are no longer in use, preventing space reclamation.

Answer

Thin pools are created using the 'pvcreate' command.

Answer

Thin provisioning requires a dm-cache device to function.

Answer

Thin volumes automatically grow when they run out of space.

Question 5

A Linux administrator is managing a database server running on CentOS 7 that uses ext4 filesystems on LVM. The server has three physical volumes: /dev/sda (200GB), /dev/sdb (200GB), and /dev/sdc (200GB) all in volume group 'vg_db'. The logical volume 'lv_data' (400GB) is used for database files. Recently, the DBA reports that database writes are slower than expected. Iostat shows high average wait times (>100ms) on /dev/sdc but normal on /dev/sda and /dev/sdb. The LVM stripes data across all three PVs with a stripe size of 64KB. Which action should the administrator take to improve performance?

Accepted Answer

Replace /dev/sdc with a new disk and restore the mirror or restripe.. The high average wait time on /dev/sdc indicates that this specific physical volume is a performance bottleneck, likely due to hardware failure or degradation. Since the logical volume 'lv_data' stripes data across all three PVs, the overall write performance is limited by the slowest device in the stripe set. Replacing /dev/sdc with a new disk and restoring the stripe (e.g., using pvmove to relocate extents and then replacing the device) eliminates the bottleneck and restores balanced I/O across all PVs.

Answer

Convert lv_data to linear mapping on /dev/sda and /dev/sdb only.

Answer

Increase the stripe size to 256KB to reduce I/O overhead.

Answer

Remove /dev/sdc from the volume group and reduce the stripe count to 2.

Question 6

A system administrator needs to create a new 500 MB ext4 filesystem on /dev/sdb1 and mount it persistently at /data. Which set of commands accomplishes this task?

Accepted Answer

mkfs.ext4 /dev/sdb1 && echo '/dev/sdb1 /data ext4 defaults 0 2' >> /etc/fstab && mount -a. Option D is correct because it first creates an ext4 filesystem on /dev/sdb1 using mkfs.ext4, then appends a mount entry to /etc/fstab with the correct filesystem type (ext4) and mount point (/data), and finally runs mount -a to mount all filesystems from fstab, including the new one. This sequence ensures the filesystem is created, persistently configured, and immediately mounted.

Answer

mkfs -t ext4 /dev/sdb1 && mount /dev/sdb1 /data

Answer

blkid /dev/sdb1 && echo 'UUID=... /data ext4 defaults 0 2' >> /etc/fstab && mount -a

Answer

mkfs.xfs /dev/sdb1 && echo '/dev/sdb1 /data xfs defaults 0 2' >> /etc/fstab && mount -a

Question 7

Which TWO statements about LVM thin provisioning are correct?

Accepted Answer

It allows creating logical volumes that can be larger than the available physical storage.. Option B is correct because LVM thin provisioning allows creating logical volumes that appear larger than the available physical storage (overcommitment). This is achieved by allocating data blocks on demand from a thin pool, rather than reserving them at creation time. The thin pool itself must have sufficient physical storage to accommodate actual writes, but the logical volume size can exceed the pool's capacity.

Answer

Thin pools automatically extend when they reach 80% usage.

Answer

A thin pool cannot be extended once created.

Answer

It is only supported on SSDs.

Question 8

The administrator wants to create a RAID 1 array using /dev/sdb1 and /dev/sdc1, then create a filesystem and mount it at /mnt/raid1. Which command sequence should be used first?

Accepted Answer

mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdb1 /dev/sdc1. Option B is correct because the first step in creating a RAID 1 array is to assemble the underlying block devices into a RAID device using mdadm. The command `mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdb1 /dev/sdc1` initializes the RAID metadata and creates the array at /dev/md0. Only after the array is created can a filesystem be built on it and then mounted.

Answer

mkfs.ext4 /dev/md0

Answer

pvcreate /dev/sdb1 /dev/sdc1

Answer

fdisk /dev/sdb && fdisk /dev/sdc

Question 9

Order the steps to configure a Linux system as a DHCP client using dhclient.

Question 10

Arrange the steps to configure a Linux system as a PostgreSQL database server.