JN0-106 Practice Test 1 — 10 Questions

Question 1

When configuring a new Juniper router, an engineer needs to ensure that configuration changes are not automatically committed after a certain time if not explicitly confirmed. Which configuration parameter controls this?

Choose an answer to begin — your selection is scored in the full session.

Accepted Answer

commit confirmed. The 'commit confirmed' command is used to apply a configuration change that will automatically roll back to the previous configuration if not explicitly confirmed within a specified time period (default 10 minutes). This ensures that changes are not permanently applied unless the engineer verifies them, preventing accidental lockout or misconfiguration.

Answer

commit check

Answer

commit at

Answer

commit synchronize

Question 2

Which THREE route types are considered protocol-independent in Junos?

Accepted Answer

Direct routes. Direct, local, and static routes are considered protocol-independent because they are not learned or installed by any dynamic routing protocol. Direct routes are automatically created for directly connected interfaces, local routes represent the interface's own IP address, and static routes are manually configured by an administrator. These routes exist in the routing table regardless of whether any routing protocol is running, hence the term 'protocol-independent'.

Answer

BGP routes

Answer

OSPF routes

Question 3

You are troubleshooting an OSPF issue on a Juniper router. The router has a single interface ge-0/0/1 with IP 10.1.1.1/30 connected to a neighbor with IP 10.1.1.2/30. OSPF is configured area 0. The 'show ospf neighbor' command shows no neighbors. 'show interfaces ge-0/0/1 terse' shows the interface is up. 'show configuration protocols ospf' shows:
   area 0.0.0.0 {
       interface ge-0/0/1.0 {
           passive;
       }
   }
What is the problem?

Accepted Answer

The OSPF interface is configured as passive. The 'passive' statement under the OSPF interface configuration prevents the router from sending or processing OSPF Hello packets on that interface. Without Hello packets, the router cannot discover neighbors or form adjacencies, which is why 'show ospf neighbor' returns no neighbors even though the interface is operationally up.

Answer

The hello timer is too slow

Answer

Authentication is missing

Answer

The interface is administratively down

Question 4

A network engineer wants to schedule a reboot of a Juniper device at 3:00 AM. Which command should be used?

Accepted Answer

request system reboot at 03:00. The 'request system reboot at 03:00' command schedules a one-time reboot of the Juniper device at the specified time (3:00 AM). The 'at' parameter allows the engineer to set an absolute time for the reboot, which is the exact requirement for scheduling a reboot at a specific future time.

Answer

request system configuration rescue save

Answer

request system reboot

Answer

load override /config/juniper.conf.gz

Question 5

A junior engineer needs to collect a snapshot of the current system state, including routing tables, interfaces, and configuration, for a support ticket. Which command achieves this?

Accepted Answer

request support information. The 'request support information' command is the correct choice because it collects a comprehensive snapshot of the current system state, including routing tables, interface details, configuration, logs, and other operational data into a single archive file. This is specifically designed for support tickets, as it bundles all relevant diagnostic information in one step, unlike individual show commands that only capture partial data.

Answer

show configuration

Answer

show interfaces

Answer

show route

Question 6

A network engineer needs to revert to the configuration that was active before the last commit. Which command accomplishes this?

Accepted Answer

rollback 1. The 'rollback 1' command reverts the active configuration to the configuration that was committed immediately before the most recent commit. Junos maintains up to 50 previous committed configurations (rollback 0 being the current active configuration, rollback 1 the previous, and so on). This command is the correct way to undo the last commit without manually editing the configuration.

Answer

rollback 0

Answer

load override

Answer

revert

Question 7

During a maintenance window, an engineer needs to apply a series of configuration changes that are stored in a text file. Which command sequence should be used to load and apply the changes from the file?

Accepted Answer

configure; load merge /var/tmp/changes.txt; commit. The engineer needs to enter configuration mode (configure) and then use the 'load merge' command to merge the contents of the text file into the candidate configuration without replacing the entire configuration. The 'commit' command then activates the changes. This is the standard Junos workflow for applying incremental changes from a file.

Answer

request system configuration rescue save

Answer

load override /var/tmp/changes.txt; commit

Answer

configure; load patch /var/tmp/changes.txt; commit

Question 8

Which Junos command displays the route to a specific IP address, including the active route and any backup routes?

Accepted Answer

show route 192.168.1.1. The 'show route 192.168.1.1' command in Junos displays all routes in the routing table that match the specified destination, including the active route (marked with '>') and any backup routes (marked with a space). This command provides a comprehensive view of the forwarding table entries for that prefix, which is essential for understanding both primary and failover paths.

Answer

show route protocol

Answer

show route active

Answer

show route table

Question 9

A network engineer needs to make a change to a Junos device and ensure the change can be reverted if it causes issues. Which feature should be used?

Accepted Answer

commit confirmed. The `commit confirmed` command allows an engineer to commit a configuration change with a timer (default 10 minutes). If the change causes issues and the engineer does not confirm the commit within the timer, the device automatically reverts to the previous active configuration. This provides a safety net to revert changes without manual intervention.

Answer

configure exclusive

Answer

commit check

Answer

rollback 0

Question 10

Refer to the exhibit. An administrator notices repeated failed login attempts. What should be configured to mitigate this attack?

Accepted Answer

Configure a firewall filter to block the source IP. A firewall filter can block traffic from the source IP address of the repeated failed login attempts, preventing further access from that host. This is a direct and immediate mitigation against an ongoing brute-force attack, as it stops the attacker's traffic at the network layer before it reaches the SSH or login service.

Answer

Set login retry limit

Answer

Disable SSH

Answer

Change the root password