350-501 Timed Practice Test 1 — 10 Questions

Question 1

An engineer is troubleshooting an MPLS network where some routers are not exchanging labels via LDP. Which two steps are most appropriate for diagnosing the issue? (Choose two.)

Accepted Answer

Verify LDP neighbor adjacencies using 'show mpls ldp neighbor'.. Option A is correct because 'show mpls ldp neighbor' displays the state of LDP sessions (Operational, Non-existent, etc.) and the TCP connection status to each peer, which directly reveals whether label distribution adjacencies are forming. Option E is correct because LDP only runs on interfaces where 'mpls ip' (or 'mpls ldp' on some platforms) is enabled, and 'show mpls ldp interface' confirms which interfaces are actively participating in LDP label exchange. Option B is not appropriate because MTU mismatches typically affect data forwarding or IGP adjacency formation, not the LDP session establishment itself. Option C is not appropriate because rebooting routers is a disruptive action that does not diagnose the root cause of failed LDP sessions. Option D is not appropriate because while LDP relies on underlying IP reachability (often provided by OSPF), verifying OSPF adjacencies alone does not confirm LDP-specific configuration or session state.

Answer

Check the MTU size on all interfaces.

Answer

Reboot all routers to reset LDP sessions.

Answer

Verify that OSPF neighbor relationships are established.

Question 2

Which TWO statements about QoS policy propagation via BGP (QPPB) are correct?

Accepted Answer

QPPB can be applied on inbound direction only.. QPPB can be applied on inbound direction only. QPPB uses BGP policy to classify traffic based on IP precedence or QoS group, and the classification is performed on incoming traffic before any routing decision. The outbound direction is not supported for QPPB classification.

Answer

QPPB is an IETF standard.

Answer

It uses MPLS EXP bits to propagate QoS.

Answer

It dynamically adjusts BGP attributes based on QoS policy.

Question 3

Which three of the following are valid methods for protecting a pseudowire in an MPLS network?

Accepted Answer

Multi-segment PW with backup. Multi-segment PW (MS-PW) with backup is a valid protection method because it allows a pseudowire to be established across multiple MPLS segments, with a backup PW path that can take over if the primary MS-PW fails. This provides end-to-end pseudowire redundancy by using a secondary switched path, ensuring service continuity in multi-domain or multi-area MPLS networks.

Answer

Ethernet OAM CFM

Answer

LSP ping for fault detection

Question 4

What is the purpose of NTP authentication in a service provider network?

Accepted Answer

To verify the identity of the NTP server. NTP authentication (RFC 5905) uses symmetric key cryptography (MD5, SHA-1, or SHA-256) to verify that time updates come from a trusted NTP server. Its purpose is to prevent an attacker from spoofing NTP packets and injecting false time, which could disrupt logging, certificates, and routing protocols. It authenticates the source, not the content's confidentiality.

Answer

To encrypt NTP traffic

Answer

To rate-limit NTP packets

Answer

To synchronize time across devices

Question 5

A large enterprise uses MPLS L3VPN to connect multiple sites. They want to implement inter-AS option B (ASBR-to-ASBR MP-eBGP) for scalability. Which statement about this model is correct?

Accepted Answer

ASBRs exchange VPNv4 routes using MP-eBGP. In Inter-AS Option B, ASBRs use MP-eBGP to exchange VPNv4 routes. They do not maintain VRFs (Option A incorrect), and sessions are per address family, not per VRF (Option C incorrect). Option B is incorrect because a full mesh of MP-iBGP between PEs is not required. Option D correctly describes the VPNv4 route exchange using MP-eBGP.

Answer

Each ASB router maintains VRFs for all attached customers

Answer

Inter-AS option B requires a full mesh of MP-iBGP between all PEs

Answer

MP-eBGP sessions are established per VRF between ASBRs

Question 6

A service provider is designing a new MPLS L3VPN service. The customer requires that their VPN traffic be isolated from other customers and that the provider edge routers maintain separate routing tables for each VPN. Which architectural component is essential for this separation?

Accepted Answer

VRF (Virtual Routing and Forwarding). VRF (Virtual Routing and Forwarding) is the essential architectural component that enables a provider edge router to maintain separate, isolated routing tables for each VPN customer. Each VRF instance contains its own routing table, CEF (Cisco Express Forwarding) table, and associated interfaces, ensuring that traffic from one customer is never forwarded using another customer's routing information. This per-VPN isolation is fundamental to MPLS L3VPN services as defined in RFC 4364.

Answer

MPLS label stacking

Answer

VLAN tagging on the customer-facing interfaces

Answer

BGP route reflectors

Question 7

When implementing MPLS TE tunnels in a service provider core, what is the purpose of the 'affinity' attribute?

Accepted Answer

To define administrative groups for link inclusion/exclusion. The 'affinity' attribute in MPLS TE is used to define administrative groups (also known as link colors) that allow you to include or exclude specific links from a TE tunnel path based on user-defined properties. This enables traffic engineering policies such as forcing traffic to avoid certain links or preferring links with specific characteristics, without modifying the underlying IGP metric.

Answer

To set the color of the tunnel

Answer

To adjust the cost of TE tunnels

Answer

To bind tunnels to specific interfaces

Question 8

During a network migration from EIGRP to OSPF, you notice that some routes are being redistributed incorrectly, causing routing loops. The OSPF domain uses area 0 and area 1. The EIGRP domain uses AS 100. Which configuration change would best prevent loops during the migration?

Accepted Answer

Use route-maps to tag EIGRP routes and filter them on OSPF routers.. Route-maps allow you to tag redistributed EIGRP routes with a specific tag value (e.g., 'tag 100') and then filter those tagged routes on OSPF routers using a distribute-list in or prefix-list combined with the route-map. This prevents the redistributed routes from being re-injected back into EIGRP, breaking the redistribution loop. Without such tagging and filtering, mutual redistribution between EIGRP and OSPF can cause routing loops due to the two-way redistribution of routes.

Answer

Implement OSPF stub areas to limit external routes.

Answer

Use distribute-list in EIGRP to block OSPF routes.

Answer

Set a high administrative distance on redistributed routes in OSPF.

Question 9

An MPLS core network uses LDP to distribute labels. An engineer wants to verify that the LDP session between two routers is up and exchanging labels. Which command should be used?

Accepted Answer

show mpls ldp neighbor. The command 'show mpls ldp neighbor' displays the status of LDP sessions, including the neighbor's IP address, session state (e.g., Operational), and label exchange activity. Since LDP is the protocol used to distribute labels in this MPLS core network, this command directly verifies that the session is up and exchanging labels between the two routers.

Answer

show mpls interfaces

Answer

show mpls l2transport binding

Answer

show mpls forwarding-table

Question 10

Which OSPF network type elects a Designated Router (DR) and Backup Designated Router (BDR) to reduce the number of adjacencies on a multi-access segment?

Accepted Answer

Broadcast. The OSPF broadcast network type is designed for multi-access segments like Ethernet, where multiple routers can communicate directly. On broadcast networks, OSPF elects a Designated Router (DR) and Backup Designated Router (BDR) to reduce the number of adjacencies from O(n²) to O(n), since all non-DR routers form adjacencies only with the DR and BDR. This is the defining behavior of the broadcast network type.

Answer

Point-to-point

Answer

Loopback

Answer

Point-to-multipoint