220-1201 Practice Test 6 — 10 Questions

Question 1

A customer reports that their internet connection drops frequently during rainstorms. They have a cable modem and a wireless router. What is the most likely cause of the intermittent connection?

Accepted Answer

The cable modem's coaxial cable connection is compromised by moisture.. Cable internet relies on a coaxial cable connection from the street to the modem. During rainstorms, moisture can seep into damaged or poorly sealed coaxial connectors or cable sheathing, causing signal attenuation or intermittent shorting that drops the connection. This is a classic symptom of RF signal degradation due to water ingress, which directly affects the physical layer (Layer 1) of the cable modem's link.

Answer

The wireless router is overheating.

Answer

The DSL filter is malfunctioning.

Answer

The satellite dish is out of alignment.

Question 2

A technician is tasked with upgrading the RAM in an all-in-one (AIO) desktop. The AIO has a sealed back cover with several screws. After removing the screws, the cover still does not come off. What should the technician do next?

Accepted Answer

Use a plastic spudger to gently pry the cover along the seam to release clips.. All-in-one (AIO) desktops often use plastic clips along the seam in addition to screws to secure the back cover. After removing all visible screws, a plastic spudger is the proper tool to gently release these clips without damaging the casing or internal components. Forceful prying with metal tools or applying heat can crack the plastic or damage the display panel.

Answer

Use a flathead screwdriver to pry the cover off forcefully.

Answer

Check if there are hidden screws under rubber feet or stickers.

Answer

Apply heat to the back cover to soften any adhesive.

Question 3

A technician is configuring a router with two interfaces: WAN (DHCP from ISP) and LAN (static IP 10.0.0.1/24). The technician sets the LAN subnet mask to 255.255.255.0. A workstation is assigned IP 10.0.0.100/24 and can ping the router, but cannot access the internet. The router's WAN interface has IP 203.0.113.5/30. What is the most likely missing configuration?

Accepted Answer

The router lacks a default route pointing to the ISP's gateway.. The workstation can ping the router's LAN interface (10.0.0.1), confirming Layer 2 and basic IP connectivity on the LAN. However, for the workstation to reach the internet, the router must have a default route (0.0.0.0/0) pointing to the ISP's next-hop gateway (likely 203.0.113.6, the other end of the /30 WAN link). Without this route, the router does not know where to forward packets destined for external networks, even though the WAN interface has a valid IP from DHCP.

Answer

The workstation's default gateway is set to 10.0.0.1.

Answer

The WAN subnet mask should be 255.255.255.0.

Answer

The LAN subnet mask should be 255.255.0.0.

Question 4

A user's smartphone can connect to a corporate Wi-Fi network but cannot access any internet sites. Other devices on the same network work fine. The smartphone shows it is connected with full signal. What is the most likely cause?

Accepted Answer

The smartphone's DNS settings are misconfigured or pointing to a non-functional server.. The smartphone can connect to the Wi-Fi network (Layer 2 connectivity is fine) and other devices work, so the issue is specific to this device's higher-layer configuration. DNS resolution is required to translate domain names to IP addresses; if the smartphone's DNS settings point to a non-functional or incorrect server, it will fail to resolve any hostname, preventing internet access even though the network connection itself is active. This matches the symptom of being connected with full signal but unable to browse.

Answer

The corporate network is blocking the smartphone's MAC address.

Answer

The smartphone's Wi-Fi adapter is faulty.

Answer

The corporate proxy server is down.

Question 5

A user complains that their wireless Bluetooth earbuds frequently disconnect during calls when their smartphone is in their pocket. The earbuds work fine when the phone is on a desk. Which accessory or configuration change is most likely to resolve this issue?

Accepted Answer

A Bluetooth neckband style headset. The issue is that the smartphone's Bluetooth antenna is being physically blocked or attenuated by the user's body (specifically the leg/torso) when the phone is in a pocket. A Bluetooth neckband-style headset places the Bluetooth receiver and antenna around the user's neck, which is typically above the pocket and has a clearer line-of-sight to the phone, significantly reducing signal obstruction and multipath interference. This configuration change directly addresses the physical signal path problem without requiring any software or network changes.

Answer

A Bluetooth signal booster app

Answer

A metal phone case

Answer

A Wi-Fi analyzer to change router channels

Question 6

A technician is troubleshooting a smartphone that can send and receive text messages but cannot make or receive phone calls. The device shows full signal bars. Which network setting is most likely misconfigured?

Accepted Answer

The device's preferred network type is set to 'LTE only' and VoLTE is disabled.. When a smartphone shows full signal bars but cannot make or receive voice calls while SMS works, the most likely cause is that the device is set to 'LTE only' as its preferred network type and VoLTE (Voice over LTE) is disabled. SMS can be carried over LTE via IMS (IP Multimedia Subsystem) or fallback to circuit-switched networks, but voice calls require either VoLTE or a circuit-switched fallback (CSFB) to 2G/3G. With 'LTE only' selected and VoLTE off, the device cannot initiate or accept voice calls because it lacks a circuit-switched connection and has no fallback path.

Answer

The device's data roaming is turned off.

Answer

The device's Bluetooth is enabled.

Answer

The device's airplane mode is turned on.

Question 7

A company's file server uses a RAID 5 array with five 4 TB hard drives. One drive fails and is replaced. During the rebuild, the server crashes and the RAID controller reports that the array is 'Failed'. What is the most likely reason for this catastrophic failure?

Accepted Answer

A second drive failed during the rebuild process.. In RAID 5, a single drive failure is survivable, but during rebuild, the remaining drives are under heavy read stress. If another drive fails or has an unrecoverable read error, the array fails. This is known as a 'double fault' during rebuild, a common risk with large-capacity drives.

Answer

The new drive was not properly formatted before installation.

Answer

The RAID controller cache battery is dead.

Answer

The rebuild was attempted while the server was under heavy load.

Question 8

A technician is troubleshooting a home network where the 5 GHz band works fine, but the 2.4 GHz band is extremely slow and drops connections. The router is placed near a cordless phone base station. Which type of interference is most likely occurring?

Accepted Answer

RF interference from the cordless phone base. The 2.4 GHz band is shared by many consumer devices, including cordless phones that operate in the 2.4 GHz ISM band. The proximity of the router to the cordless phone base station causes RF interference, which degrades the 2.4 GHz signal, leading to slow speeds and dropped connections, while the 5 GHz band remains unaffected because it operates on a different frequency range.

Answer

Bluetooth interference

Answer

Microwave oven interference

Answer

Co-channel interference from a neighboring Wi-Fi network

Question 9

A technician is configuring a tablet for field workers who need to transfer large files to a central server. The tablet has a USB-C port. Which connection method provides the fastest data transfer speed?

Accepted Answer

USB 3.1 Gen 2 over USB-C. USB 3.1 Gen 2 over USB-C supports a maximum signaling rate of 10 Gbps, which is significantly faster than any wireless or NFC option. For transferring large files to a central server, this wired connection provides the highest throughput and lowest latency, making it the optimal choice for the scenario.

Answer

Bluetooth 5.0

Answer

Wi-Fi 5 (802.11ac)

Answer

NFC

Question 10

A technician is installing a new SSD into a customer's laptop. After removing the bottom cover, they see the existing hard drive is held in place by a metal bracket and a single screw. What is the correct next step?

Accepted Answer

Remove the screw and bracket, then gently lift the drive out of the SATA connector.. The correct next step is to remove the screw and bracket, then gently lift the drive out of the SATA connector. This is because the metal bracket secures the drive in place, and the SATA connector is a fragile, keyed interface that requires a straight, gentle pull to avoid damaging the pins or the drive's edge connector. Forcing the drive or prying it can bend pins or crack the connector.

Answer

Pull the drive straight out with force to disconnect it.

Answer

Use a plastic spudger to pry the drive from the connector.

Answer

Remove the battery first to avoid electrical shock.