JNCIA-JUNOS Routing Fundamentals Practice Question
This JNCIA-JUNOS practice question tests your understanding of routing fundamentals. Read the scenario carefully and evaluate each option against the stated constraints before committing to an answer. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Which THREE factors influence the selection of the active route in the Junos routing table when multiple routes exist for the same destination? (Choose three.)
Answer the question above first, then reveal the full breakdown to understand why each option is right or wrong.
Correct answer & explanation
✓
Route preference (administrative distance).
Options B, C, and E are correct. B: Route preference (administrative distance) is the primary tiebreaker. C: Metric (e.g., OSPF cost) is considered after preference if routes are from the same protocol. E: The route's source protocol (e.g., OSPF vs Static) determines default preference values. A is incorrect; the routing table does not consider interface bandwidth in route selection. D is incorrect; the number of next-hops is not a selection criterion; all equal-cost next-hops are used.
Key principle: OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Answer analysis
Option-by-option breakdown
For each option: why learners choose it and why it is or isn't the right answer here.
Bandwidth is not a selection criterion in Junos route selection.
Common exam traps
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Detailed technical explanation
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
OSPF neighbours must agree on key parameters.
Router ID selection can affect neighbour relationships and LSDB output.
OSPF cost influences the preferred path.
A route can appear in OSPF information but not become the installed route.
TExam Day Tips
→Check area mismatch first when OSPF adjacency fails.
→Review passive interfaces when a network is advertised but no neighbour forms.
→Use show ip ospf neighbor and show ip route clues carefully.
Key takeaway
OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Real-world example
How this comes up in practice
A network engineer at a university connects two campus buildings via a fibre link. Both routers run OSPF, but no adjacency forms — even though both routers can ping each other. The engineer finds one router is in area 0 and the other in area 1. OSPF adjacency requires matching area numbers, hello/dead timers, and network type. IP reachability alone is not enough.
What to study next
Got this wrong? Here's your next step.
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related JNCIA-JUNOS OSPF questions on adjacency and route selection.
Routing Fundamentals — This question tests Routing Fundamentals — OSPF neighbours must agree on key parameters..
What is the correct answer to this question?
The correct answer is: Route preference (administrative distance). — Options B, C, and E are correct. B: Route preference (administrative distance) is the primary tiebreaker. C: Metric (e.g., OSPF cost) is considered after preference if routes are from the same protocol. E: The route's source protocol (e.g., OSPF vs Static) determines default preference values. A is incorrect; the routing table does not consider interface bandwidth in route selection. D is incorrect; the number of next-hops is not a selection criterion; all equal-cost next-hops are used.
What should I do if I get this JNCIA-JUNOS question wrong?
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related JNCIA-JUNOS OSPF questions on adjacency and route selection.
What is the key concept behind this question?
OSPF neighbours must agree on key parameters.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
This JNCIA-JUNOS practice question is part of Courseiva's free Juniper Networks certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the JNCIA-JUNOS exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.