Question 1mediumdrag order
Review the full OSPF breakdown →Answer choices are not available in this preview. Open the full question page for the complete review.
Question 93 of 514
JNCIA-JUNOS Operational Monitoring and Maintenance Practice Question
This JNCIA-JUNOS practice question tests your understanding of operational monitoring and maintenance. This is a configuration task: choose the command set that satisfies every stated requirement. Small differences — like 'secret' vs 'password' or 'transport input ssh' vs 'all' — change whether the answer is correct. After answering, compare your reasoning against the explanation and wrong-answer breakdown below. Once you have made your selection, read the full explanation to reinforce the concept and understand why each distractor is designed to mislead on exam day.
Arrange the steps to configure OSPF on a Junos router in the correct order.
Correct answer & explanation
OSPF requires a router ID and interfaces assigned to areas. Verification shows neighbor relationships.
Key principle: OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Common exam traps
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Detailed technical explanation
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
- OSPF neighbours must agree on key parameters.
- Router ID selection can affect neighbour relationships and LSDB output.
- OSPF cost influences the preferred path.
- A route can appear in OSPF information but not become the installed route.
TExam Day Tips
- Check area mismatch first when OSPF adjacency fails.
- Review passive interfaces when a network is advertised but no neighbour forms.
- Use show ip ospf neighbor and show ip route clues carefully.
Key takeaway
OSPF neighbour adjacency depends on matching area, hello/dead timers, network type, and authentication — IP reachability alone is not enough.
Real-world example
How this comes up in practice
A network engineer at a university connects two campus buildings via a fibre link. Both routers run OSPF, but no adjacency forms — even though both routers can ping each other. The engineer finds one router is in area 0 and the other in area 1. OSPF adjacency requires matching area numbers, hello/dead timers, and network type. IP reachability alone is not enough.
What to study next
Got this wrong? Here's your next step.
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related JNCIA-JUNOS OSPF questions on adjacency and route selection.
- →
Operational Monitoring and Maintenance — study guide chapter
Learn the concepts, then practise the questions
- →
Operational Monitoring and Maintenance practice questions
Targeted practice on this topic area only
- →
All JNCIA-JUNOS questions
514 questions across all exam domains
- →
Juniper Networks Certified Associate Junos JNCIA-Junos study guide
Full concept coverage aligned to exam objectives
- →
JNCIA-JUNOS practice test guide
How to use practice tests most effectively before exam day
Related practice questions
Related JNCIA-JUNOS practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
User Interfaces practice questions
Practise JNCIA-JUNOS questions linked to User Interfaces.
Junos Configuration Basics practice questions
Practise JNCIA-JUNOS questions linked to Junos Configuration Basics.
Operational Monitoring and Maintenance practice questions
Practise JNCIA-JUNOS questions linked to Operational Monitoring and Maintenance.
Routing Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Routing Fundamentals.
Networking Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Networking Fundamentals.
Junos OS Fundamentals practice questions
Practise JNCIA-JUNOS questions linked to Junos OS Fundamentals.
JNCIA-JUNOS fundamentals practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS fundamentals.
JNCIA-JUNOS scenario practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS scenario.
JNCIA-JUNOS troubleshooting practice questions
Practise JNCIA-JUNOS questions linked to JNCIA-JUNOS troubleshooting.
Practice this exam
Start a free JNCIA-JUNOS practice session
Short sessions build daily habit. Longer sessions build exam-day stamina. Try a timed session to simulate real conditions.
FAQ
Questions learners often ask
What does this JNCIA-JUNOS question test?
Operational Monitoring and Maintenance — This question tests Operational Monitoring and Maintenance — OSPF neighbours must agree on key parameters..
What exam trap should I watch out for?
Common exam trap: OSPF can fail even when IP connectivity looks correct: OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
What should I do if I get this JNCIA-JUNOS question wrong?
Review OSPF neighbour requirements — matching area type, hello and dead timers, network type, stub flags, and authentication. Study show ip ospf neighbor states (INIT, 2-WAY, FULL). Then practise related JNCIA-JUNOS OSPF questions on adjacency and route selection.
What is the key concept behind this question?
OSPF neighbours must agree on key parameters.
About these practice questions
Courseiva creates original exam-style practice questions with explanations and wrong-answer analysis. It does not publish real exam questions, exam dumps, or protected exam content. Learn why practice questions differ from exam dumps →
Keep practising
More JNCIA-JUNOS practice questions
- A junior engineer needs to collect a snapshot of the current system state, including routing tables, interfaces, and con…
- A network engineer is troubleshooting a connectivity issue and wants to see the active routes in the routing table. Whic…
- You are the network engineer for a mid-sized enterprise with a Juniper MX router running Junos. The router has two uplin…
- Which TWO attributes are used by Junos to select the active route among multiple routes to the same destination?
- What is the default preference of a direct route in Junos?
- A router has two routes to the same destination: one with preference 10 and metric 5, and another with preference 15 and…
Last reviewed: Jun 11, 2026
This JNCIA-JUNOS practice question is part of Courseiva's free Juniper Networks certification practice question bank. Courseiva provides original exam-style practice questions with explanations, topic-based practice, mock exams, readiness tracking, and study analytics to help learners prepare for the JNCIA-JUNOS exam.
Question Discussion
Share a tip, memory trick, or ask about the reasoning behind this question. Do not post real exam questions, leaked content, braindumps, or copyrighted exam material. Comments are moderated and may be removed without notice.
Sign in to join the discussion.