F5CAB1 Install, Initial Configuration, and Upgrade Practice Test 1 — 15 Questions

Question 1

An administrator is performing an initial setup on a new BIG-IP platform via the Configuration Utility. Which step is mandatory to ensure the device can be licensed and receive updates from F5?

Accepted Answer

Configure the management IP address and default gateway.. Validating connectivity to the licensing server is critical during initial deployment. The BIG-IP must resolve the F5 license activation server address, typically requiring correct DNS configuration and routing. Without a valid license, the system remains in a non-functional state, preventing configuration of traffic management objects. This process ensures the hardware or virtual instance is authorized and entitled to the features requested during the provisioning phase of the installation.

Answer

Provision all modules to the 'Dedicated' resource level.

Answer

Create a high availability group with another unit.

Answer

Define a custom administrative partition for management.

Question 2

Refer to the exhibit. An administrator is planning to upgrade the BIG-IP to version 17.1.1. Which action should be taken to ensure the upgrade succeeds while maintaining the ability to revert to the currently running version?

Accepted Answer

Install the new version into volume MD1.3.. The administrator must install the new version into an inactive volume, specifically HD1.3, to preserve the existing working environment on HD1.1. By installing to an unused volume, the current configuration remains untouched, allowing for a quick rollback if the upgrade fails or exhibits post-upgrade issues. Maintaining boot locations is a best practice for risk mitigation during major software transitions, ensuring service continuity is prioritized alongside firmware updates.

Answer

Install the new version into volume MD1.1.

Answer

Delete volume MD1.2 before starting the installation.

Answer

Activate MD1.2 before installing the new software.

Question 3

Which TWO items must be correctly configured to ensure the BIG-IP device can send email alerts for system events?

Accepted Answer

SMTP server hostname or IP address.. To send email alerts, the BIG-IP requires a functional SMTP relay server address, which the device uses to send outbound notifications. Additionally, the administrator must configure the alerting system, specifically defining the 'SNMP' or 'Email' alert recipients. Without the SMTP server configuration, the device has no path to transmit the mail, and without defined recipients, the alerts have no destination address for delivery.

Answer

Default Gateway for the data plane.

Answer

Active Directory domain controller.

Answer

SSL certificate for the email server.

Question 4

An administrator observes that the BIG-IP system is constantly rebooting into an old boot volume despite installing a new version in a different volume. What is the most likely cause?

Accepted Answer

The boot-default parameter is not updated.. The BIG-IP boot order is determined by the system's GRUB/BIOS settings, which prioritize the boot volume. If the system is not told to switch the default boot location, it will continue to boot into the previously active volume. The administrator must explicitly set the new, updated volume as the 'default' boot location to ensure the system boots into the new version upon any subsequent restart.

Answer

The license is expired.

Answer

The system clock is not synchronized.

Answer

The management interface is disconnected.

Question 5

An administrator is performing a fresh installation of BIG-IP VE on a hypervisor. After booting, the system fails to acquire an IP address via DHCP on the management interface. Which command should the administrator use to manually configure the management IP address?

Accepted Answer

config. The config utility provides the initial setup wizard to configure the management network, but the tmsh command line is the robust way to ensure settings persist after a reboot. Administrators must frequently handle cases where DHCP is unavailable in isolated management networks. Understanding this manual configuration process is critical for ensuring the device is reachable for further licensing and provisioning tasks within a restricted data center environment.

Answer

config_mgmt --ip 192.168.1.5 --netmask 255.255.255.0

Answer

tmsh modify sys management-ip 192.168.1.5/24

Answer

ip address add 192.168.1.5/24 dev eth0

Question 6

An administrator is upgrading a BIG-IP pair from v14.1 to v16.1. Which TWO tasks must be performed to ensure a successful upgrade of the High Availability pair?

Accepted Answer

Install the new software version on an inactive volume.. Upgrading HA pairs requires a methodical approach to ensure traffic continuity and configuration integrity. By installing to an inactive partition and performing a configuration sync, the administrator minimizes downtime and mitigates risks associated with software incompatibility. These steps are standard industry best practices for F5 deployments, ensuring that the standby unit is prepared to take over traffic seamlessly if the primary unit fails during the transition.

Answer

Install the new software version on the active partition.

Answer

Delete the old configuration files before upgrading.

Answer

Change the device trust to 'standby' mode.

Question 7

Which THREE items must be configured in the initial setup wizard to allow the BIG-IP to communicate with the network?

Accepted Answer

Management IP address and netmask.. Setting up the management network is the prerequisite for all subsequent management. Without these core components, the BIG-IP cannot be managed remotely, nor can it download licenses or security updates. Mastering the basic network setup is essential for F5 administrators, as this configuration forms the backbone for all remote administrative connectivity and interaction with centralized management platforms.

Answer

SNMP community string.

Answer

VLAN 10 tagging for data traffic.

Question 8

An administrator is planning a BIG-IP software upgrade using the 'image2disk' utility. Which TWO factors must be verified to ensure a successful installation?

Accepted Answer

Verify the MD5 checksum of the ISO image.. Successful upgrades rely on both file integrity and hardware compatibility. Verifying the MD5 checksum ensures the ISO was not corrupted during transfer, preventing installation failures. Checking the platform support confirms the image is compatible with the underlying hardware or hypervisor architecture. These checks are critical to prevent bricking the device or encountering post-upgrade boot loops, which would require manual recovery via the serial console.

Answer

Ensure the current license is valid for the new version.

Answer

Confirm the target partition has sufficient disk space.

Answer

Check if SSH is enabled for remote updates.

Question 9

Refer to the exhibit. The administrator has installed a new version on HD1.2. What command must be executed to switch to the new version upon reboot?

Accepted Answer

switchboot -d HD1.2. The 'switch' command designates the target volume as the next boot location. Without this command, the system will continue to boot from the current active partition (HD1.1) upon reboot. Properly managing the boot slot is critical for controlling the rollout of new versions, ensuring that the system transitions to the desired software version in a controlled, predictable manner during the next maintenance cycle.

Answer

tmsh modify sys software volume HD1.2 active

Answer

tmsh boot volume HD1.2

Answer

set-boot-location HD1.2

Question 10

Which utility should an administrator use to monitor the status of a software installation in progress?

Accepted Answer

Check the '/var/log/liveinstall.log' file.. The 'tmsh' utility, specifically using the 'show sys software' command, provides real-time visibility into the installation status. It shows the progress, which volume is being updated, and whether the process has completed. Monitoring this is critical during maintenance to ensure the process hasn't stalled, allowing the administrator to respond quickly to potential issues and verify that the installation finishes correctly without corrupting the target boot volume.

Answer

Use the 'top' command.

Answer

Run 'netstat -an'.

Answer

Restart the management services.

Question 11

An administrator is performing an initial setup on a new BIG-IP platform via the Configuration Utility. Which step is mandatory to ensure the device can be licensed and receive updates from F5?

Choose an answer to begin — your selection is scored in the full session.

Accepted Answer

netstat -tulpn | grep httpd. Verifying the listening status of the httpd service is critical for troubleshooting initial connectivity issues during BIG-IP deployment. If the service is down or failing to bind to the management IP, the web interface will remain inaccessible despite correct network routing. This step validates whether the issue is at the application layer or a network-level connectivity problem, ensuring a systematic approach to resolving configuration bottlenecks.

Answer

tmsh show sys hardware

Answer

tmsh show sys interface mgmt

Answer

tcpdump -ni mgmt port 443

Question 12

An administrator is planning a software upgrade from BIG-IP 14.1.x to 17.1.x. Which TWO tasks are mandatory prerequisites to ensure a successful transition?

Accepted Answer

Run the qkview utility and check for configuration compatibility.. Upgrading major versions requires strict adherence to the defined upgrade path and system health checks. By validating the configuration and preparing the target boot location, the administrator minimizes the risk of service disruption or configuration loss. These steps are fundamental to maintaining high availability and ensuring that the new software environment is fully functional upon reboot, preventing common pitfalls associated with incompatible legacy settings during the migration process.

Answer

Delete all existing SSL certificates from the device.

Answer

Disable all traffic processing to improve installation speed.

Answer

Update the BIOS firmware manually before running the installer.

Question 13

Refer to the exhibit. An administrator just completed an upgrade and received this error while loading the configuration. What is the most likely cause?

Accepted Answer

The pool was removed from the configuration file before the upgrade.. This error signifies that the system configuration file contains a reference to a pool object that failed to migrate or was incorrectly pruned during the upgrade process. Understanding object dependency is vital because BIG-IP architecture requires all referenced objects to exist before the parent object can be instantiated. This type of error often occurs when custom configurations rely on objects that do not meet the new version's schema requirements.

Answer

The license has expired, causing the pool to be disabled.

Answer

The traffic management shell service is unresponsive.

Answer

The virtual server is using an incompatible profile.

Question 14

Which utility is primarily used to perform a full system backup of a BIG-IP device for disaster recovery purposes?

Accepted Answer

tmsh save sys config ucs. The UCS (User Configuration Set) archive is the standard method for backing up a BIG-IP device. It captures the entire configuration and critical system files required to restore a device to a known good state. Understanding how to manage UCS archives is essential for any administrator, as it provides the primary safety net during hardware failure or catastrophic configuration errors during maintenance windows.

Answer

qkview

Answer

tar -cvf backup.tar /config

Answer

tmsh save sys backup

Question 15

After installing a new software version on an inactive boot slot, what is the final action required to complete the upgrade process?

Accepted Answer

Use the 'switchboot' utility to activate the new partition.. Finalizing an upgrade requires setting the boot partition and rebooting the system. This action transitions the system from the old version to the new version. It is a critical step because the software installation only copies the files; the system must actually boot into the new partition to execute the new code. Proper management of boot locations ensures that administrators can revert if issues arise post-upgrade.

Answer

Run the 'tmsh install sys software' command again.

Answer

Restart the mcpd daemon.

Answer

Delete the old partition to free up space.