20+ practice questions focused on Infrastructure Services — one of the most tested topics on the Cisco CCNP ENARSI 300-410 exam. Each question includes a detailed explanation so you learn why the right answer is correct.
Start Infrastructure Services PracticeAn engineer is configuring MPLS L3VPN on a Cisco IOS XE router. The customer edge (CE) router uses OSPF and the provider edge (PE) router must redistribute OSPF routes into MP-BGP. Which configuration is required on the PE to prevent routing loops and ensure proper route propagation?
Explanation: When redistributing OSPF into MP-BGP in an MPLS L3VPN, the OSPF domain ID must be configured and carried as a BGP extended community. This prevents routes from being redistributed back into the same OSPF domain, which would cause loops. The PE router uses this domain ID to filter routes during redistribution back into OSPF.
A network engineer is configuring a Cisco IOS router to provide first-hop redundancy for a group of hosts on VLAN 10. The design requires that the virtual IP address be the same as the real IP address of the active router, and that the standby router preempts immediately when it becomes available. Which First Hop Redundancy Protocol (FHRP) should be implemented to meet these requirements?
Explanation: VRRP is the only FHRP that allows the virtual IP address to be identical to the physical IP address of the master router. This feature, known as the IP address owner, is useful when hosts are already configured with the real IP as their default gateway. VRRP also supports preemption, and with a preempt delay of zero, immediate takeover occurs. HSRP, GLBP, and IRDP cannot use the same IP as the active router.
A network administrator is configuring IPv6 addressing on a Cisco router. The router must automatically generate a link-local address and use EUI-64 format for interface identifiers. Which command enables this behavior on an interface?
Explanation: The ipv6 enable command enables IPv6 on an interface and automatically creates a link-local address using the EUI-64 format. This is the standard way to ensure a link-local address is present without configuring a global address. Other commands either configure global addresses or manually set link-local addresses, which is not required here.
A network administrator is deploying MPLS Layer 3 VPNs with OSPF as the PE-CE routing protocol. The customer requires that OSPF routes learned from one site be redistributed into BGP with the correct extended community to prevent routing loops and ensure proper propagation. Which BGP extended community must be attached to the redistributed routes?
Explanation: In MPLS L3VPN with OSPF as the PE-CE protocol, the OSPF domain ID extended community is used to prevent routing loops. When OSPF routes are redistributed into BGP, the PE attaches this community. If the same route is later received from another PE and redistributed back into OSPF, the domain ID match prevents re-advertisement. The route type community preserves the OSPF route type but is not for loop prevention.
A network engineer is troubleshooting a DMVPN Phase 2 deployment where spoke-to-spoke tunnels are not forming. The hub is configured correctly. Which two actions should be taken on the spokes to enable direct spoke-to-spoke communication? (Choose two.)
Explanation: For DMVPN Phase 2 spoke-to-spoke tunnels, spokes must have NHRP shortcut enabled to dynamically build tunnels upon receiving redirects. Additionally, all routers in the DMVPN cloud must share the same NHRP network ID to communicate and resolve addresses. Without these, spoke-to-spoke tunnels will not form even if the hub is configured correctly.
+15 more Infrastructure Services questions available
Practice all Infrastructure Services questions1. Baseline your knowledge
Start with 10 questions to gauge your current understanding of Infrastructure Services. This tells you whether you need a concept refresher or just practice.
2. Review every explanation
For each question — right or wrong — read the full explanation. Understanding why an answer is correct is more valuable than knowing the answer itself.
3. Focus on exam traps
Infrastructure Services questions on the 300-410 frequently use trap wording. Look for subtle differences in answers that test your precision, not just general knowledge.
4. Reach 80% consistently
Do repeated sessions until you score 80%+ three times in a row. Then move to mixed-mode practice to test cross-topic recall under realistic conditions.
The exact number varies per candidate. Infrastructure Services is tested as part of the Cisco CCNP ENARSI 300-410 blueprint. Practicing with targeted Infrastructure Services questions ensures you can handle any format or difficulty that appears.
Yes. Courseiva provides free 300-410 practice questions across all exam topics and domains. The platform includes topic-based practice, mock exams, missed-question review, bookmarked questions, and readiness tracking — no account required.
Difficulty is subjective, but Infrastructure Services is a high-priority exam concept tested in multiple ways — direct recall, scenario analysis, and command-output interpretation. Consistent practice is the best way to build confidence.
Launch a full Infrastructure Services practice session with instant scoring and detailed explanations.
Start Infrastructure Services Practice →