350-501 Timed Practice Test 4 — 10 Questions

Question 1

A network engineer is designing a Layer 2 VPN using EVPN with MPLS data plane. The customer requires all-hub multipoint connectivity with optimal multicast replication. Which EVPN route type is used to advertise multicast group membership?

Accepted Answer

Route Type 6 (Selective Multicast Ethernet Tag). Route Type 6 (Selective Multicast Ethernet Tag) is used in EVPN to advertise multicast group membership for selective multicast replication. This allows the provider edge (PE) routers to build optimal multicast trees for specific groups, enabling efficient all-hub multipoint connectivity with EVPN-MPLS data plane.

Answer

Route Type 3 (Inclusive Multicast Ethernet Tag)

Answer

Route Type 2 (MAC/IP Advertisement)

Answer

Route Type 4 (Ethernet Segment)

Question 2

Which TWO MPLS VPN features are used to provide Layer 3 VPN services in a service provider network?

Accepted Answer

MPLS labels. MP-BGP (Option E) is used to exchange VPNv4 routes between Provider Edge (PE) routers, carrying both the route and its corresponding MPLS label. MPLS labels (Option C) are used to forward packets across the provider core via label-switched paths (LSPs), enabling the separation of customer traffic. Together, MP-BGP and MPLS labels form the foundation of Layer 3 MPLS VPN services.

Answer

LDP

Answer

VRF

Answer

RSVP-TE

Question 3

A service provider is implementing MPLS TE to optimize bandwidth utilization. The engineer notices that tunnels are not using the explicitly configured path. What is the most likely reason?

Accepted Answer

The explicit path contains a link that is down. When an MPLS TE tunnel is configured with an explicit path, the headend router uses RSVP to signal the path and verify that all links in the path are operational. If any link in the explicit path is down, RSVP signaling fails for that path, and the tunnel may fall back to dynamic path computation or remain down, rather than using the explicitly configured path. This is the most common reason for a tunnel not using its explicit path.

Answer

RSVP is not enabled on the headend

Answer

The tunnel destination is not reachable via IGP

Answer

The tunnel is configured with 'autoroute announce'

Question 4

A service provider is designing a greenfield MPLS core and wants to minimize control-plane complexity while still supporting traffic engineering. They plan to use Segment Routing with MPLS. Which statement about Segment Routing in this context is accurate?

Accepted Answer

Segment Routing reduces the number of protocols required in the core.. Option C is correct because Segment Routing (SR-MPLS) eliminates the need for a separate label distribution protocol like LDP or RSVP-TE. The MPLS labels are derived directly from the IGP (IS-IS or OSPF) extensions, reducing control-plane complexity while still enabling traffic engineering via SR-TE policies and flexible path computation.

Answer

Segment Routing only works with IPv6 data plane.

Answer

Segment Routing uses RSVP-TE for label distribution.

Answer

Segment Routing requires TI-LFA to be enabled for traffic engineering.

Question 5

An engineer is configuring QoS on a service provider edge router to prioritize real-time traffic. Which queuing mechanism provides the lowest latency and jitter for voice traffic?

Accepted Answer

LLQ. LLQ (Low Latency Queuing) is the correct choice because it combines a strict priority queue with CBWFQ, ensuring that voice traffic is always served before any other queue. This strict priority scheduling minimizes both latency and jitter for real-time traffic, which is critical for voice quality.

Answer

FIFO

Answer

CBWFQ

Answer

WRED

Question 6

Refer to the exhibit. CE1 is not receiving the VPNv4 route for the 192.168.1.0/24 subnet. What is the most likely cause?

Accepted Answer

PE1 is missing the neighbor statement under address-family ipv4 vrf CUSTOMER_A. For CE1 to receive the VPNv4 route for 192.168.1.0/24, PE1 must redistribute the route from the VRF into BGP. The neighbor statement under address-family ipv4 vrf CUSTOMER_A is required to establish an eBGP peering with CE1 and exchange IPv4 routes within that VRF. Without it, PE1 will not send any routes to CE1, even if the VRF and route targets are correctly configured.

Answer

PE1 is missing the VRF configuration for CUSTOMER_A

Answer

CE1 is missing the network statement under router bgp 65001

Answer

The neighbor 10.0.0.2 is using an incorrect update-source

Question 7

A service provider is designing a new MPLS core network and needs to choose a routing protocol that supports traffic engineering and fast convergence. Which protocol should be used?

Accepted Answer

IS-IS. IS-IS is the correct choice because it natively supports MPLS Traffic Engineering (TE) via IS-IS TE extensions (RFC 5305) and offers fast convergence through mechanisms like IS-IS Fast Flooding and LSP throttling. Unlike OSPF, IS-IS operates directly over Layer 2, making it more scalable and robust in large service provider core networks, and it avoids the need for a separate flooding domain for TE.

Answer

RIP

Answer

EIGRP

Answer

OSPF

Question 8

A network engineer needs to design a multicast solution for IPTV distribution across a service provider network. Which protocol is best suited for building a shared distribution tree where the RP is dynamically elected?

Accepted Answer

PIM-SM with BSR. PIM-SM with BSR (Bootstrap Router) is the correct choice because it provides a dynamic, automated mechanism for electing an RP (Rendezvous Point) within a PIM-SM domain. BSR uses a distributed election process where candidate BSRs exchange bootstrap messages to elect a single BSR, which then collects candidate-RP advertisements and distributes the RP-set to all routers, enabling shared distribution trees without manual RP configuration.

Answer

PIM-DM

Answer

PIM-SM with Auto-RP

Answer

MSDP

Question 9

A service provider is designing a QoS policy for a multi-service MPLS VPN network that carries voice, video, and data traffic. The network uses DiffServ and MPLS EXP markings. The design must ensure that voice traffic is given priority over video and data, while video traffic should have better treatment than data but not at the expense of voice. The provider plans to use a hierarchical QoS (HQoS) policy at the PE-CE interfaces. Which configuration approach best meets these requirements?

Accepted Answer

Apply a parent policy with a shape for the total bandwidth and a child policy with LLQ for voice and CBWFQ for video and data.. Option C is correct because hierarchical QoS (HQoS) allows the service provider to enforce a total bandwidth shape at the parent level while using a child policy to apply LLQ for voice (ensuring strict priority) and CBWFQ for video and data (ensuring video gets better treatment than data without starving voice). This meets the requirement that video should not degrade voice, as the parent shape prevents any single class from monopolizing the link, and the child policy’s LLQ guarantees voice priority over all other traffic.

Answer

Mark voice traffic with EXP 5, video with EXP 4, and data with EXP 0, and rely on the core to prioritize based on EXP.

Answer

Use a single-level policy with LLQ for voice and video together, and CBWFQ for data.

Answer

Apply class-based shaping to each traffic class separately on the interface.

Question 10

Which TWO statements accurately describe the behavior of the QoS policy shown in the exhibit?

Accepted Answer

During congestion, video traffic is allocated 30% of the remaining bandwidth after voice is served.. Option B is correct because the policy uses the 'bandwidth remaining percent' command under the video class, which allocates 30% of the remaining bandwidth after the voice class (which is in a strict priority queue) has been served. This is the standard behavior for class-based weighted fair queuing (CBWFQ) when a priority queue is present: the priority traffic is serviced first, and then the remaining bandwidth is distributed according to the 'bandwidth remaining percent' values assigned to the non-priority classes.

Answer

The policy shapes the total output traffic to 30 Mbps.

Answer

Video traffic is placed in a strict priority queue.

Answer

The policy polices voice traffic to a maximum of 30% of the interface bandwidth.