PCNE Implementing hybrid interconnectivity — Timed 15 Questions

Question 1

A company is deploying a Dedicated Interconnect with a 10 Gbps circuit to Google Cloud. They need to ensure high availability. Which configuration is required by Google Cloud to meet the high availability SLA?

Accepted Answer

Provision two VLAN attachments on two separate Cloud Routers in different zones. To meet the high availability SLA for Dedicated Interconnect, Google Cloud requires at least two VLAN attachments, each on a separate Cloud Router in different zones. This ensures that if one zone or Cloud Router fails, traffic can still flow through the other attachment, providing redundancy. A single VLAN attachment or a single Cloud Router does not meet the 99.99% availability SLA because it creates a single point of failure.

Answer

Combine Dedicated Interconnect with a Cloud VPN tunnel for failover

Answer

Use Partner Interconnect instead of Dedicated Interconnect

Answer

Provision a single VLAN attachment on one Cloud Router

Question 2

A company has a Hybrid Connectivity setup using Cloud VPN with dynamic routing (BGP). They notice that traffic from their on-premises network to Google Cloud is intermittently dropping. The on-premises BGP speaker is sending routes with a higher local preference (200) than the Google Cloud router (default 100). What is the most likely cause of the intermittent drops?

Accepted Answer

Asymmetric routing is causing traffic to be dropped by stateful firewalls. The on-premises BGP speaker is sending routes with a higher local preference (200) than the default on Cloud Router (100). This makes the on-premises route preferred for return traffic from Google Cloud, but the forward traffic from on-premises may still use the Cloud VPN tunnel. This asymmetry causes stateful firewalls (e.g., on-premises firewall or Google Cloud firewall) to drop packets that do not match an existing session, leading to intermittent drops.

Answer

AS path prepending is causing route flapping

Answer

Cloud Router is not configured for ECMP

Answer

The BGP MED attribute is misconfigured

Question 3

A multinational corporation is connecting five on-premises data centers to Google Cloud using Cloud Interconnect. Each data center has a dedicated 10 Gbps connection. They want to ensure that if one Interconnect fails, traffic is automatically redistributed across the remaining connections without manual intervention. Which solution meets this requirement?

Accepted Answer

Use a Cloud Router with BGP and establish multiple BGP sessions over each Interconnect. Option D is correct because Cloud Router with BGP enables dynamic routing, allowing multiple BGP sessions over each Cloud Interconnect. When one interconnect fails, BGP withdraws the affected routes, and traffic is automatically redistributed across the remaining BGP sessions without manual intervention. This meets the requirement for automatic failover and load balancing across the five 10 Gbps connections.

Answer

Configure multiple VLAN attachments on a single Cloud Router and rely on link aggregation

Answer

Deploy Cloud VPN tunnels as backup and configure static routes with lower priority

Answer

Configure VPC Network Peering between all data centers and Google Cloud

Question 4

An organization wants to migrate legacy on-premises applications to Google Cloud but must maintain low-latency connectivity for real-time data synchronization. The on-premises data center is in a colocation facility that is not directly served by Google Cloud. Which hybrid connectivity option is most cost-effective while meeting the latency requirement?

Accepted Answer

Partner Interconnect. Partner Interconnect is the most cost-effective option because it provides a dedicated, low-latency connection through a supported service provider that can extend connectivity from the colocation facility to a Google Cloud region. Unlike Dedicated Interconnect, it does not require physical cross-connects in a Google Cloud colocation facility, making it ideal when the on-premises site is not directly served by Google Cloud. It meets the real-time synchronization latency requirement by offering a reliable, high-bandwidth connection with SLA-backed uptime.

Answer

Direct Peering

Answer

Cloud VPN with dynamic routing

Answer

Dedicated Interconnect

Question 5

A company is using Cloud VPN with BGP to connect their on-premises network to Google Cloud. They have two VPN tunnels from two different on-premises VPN gateways to a single Cloud VPN gateway. They notice that during maintenance on one on-premises gateway, traffic fails over to the other tunnel, but after the maintenance, traffic does not fail back. What is the most likely cause?

Accepted Answer

The BGP local preference on the primary tunnel is not higher than the backup tunnel. B is correct because BGP local preference is used to influence outbound traffic path selection. If the primary tunnel's local preference is not higher than the backup tunnel, BGP will not prefer the primary route after the backup session recovers, causing traffic to remain on the backup tunnel. This is a classic BGP route selection behavior where the highest local preference wins.

Answer

Only one VPN tunnel can be active at a time

Answer

Cloud VPN gateway does not support BGP

Answer

The backup tunnel does not have a valid BGP session

Question 6

A financial services company is required to encrypt all data in transit between their on-premises data center and Google Cloud. They have a Dedicated Interconnect connection. They want to meet the encryption requirement while minimizing overhead and complexity. Which solution should they implement?

Accepted Answer

Enable MACsec on the Dedicated Interconnect. MACsec (IEEE 802.1AE) provides Layer 2 encryption on the Dedicated Interconnect link itself, encrypting all traffic between the on-premises router and the Google Cloud edge router without requiring any changes to applications or additional VPN gateways. This meets the encryption requirement with minimal overhead and complexity because MACsec operates transparently at the data link layer, adding negligible latency and no per-packet processing overhead compared to IPsec or TLS.

Answer

Enable TLS encryption on all applications

Answer

Use Cloud VPN over the internet instead of Dedicated Interconnect

Answer

Establish an IPsec VPN tunnel over the Dedicated Interconnect

Question 7

A company wants to connect their VPC to an on-premises network using Cloud VPN. They need to ensure that traffic from Google Cloud to on-premises uses a specific route only when the primary path is available, and otherwise fails over to a backup path. Which configuration should they use?

Accepted Answer

Configure BGP on Cloud Router and advertise custom routes with appropriate metrics. Option B is correct because Cloud VPN with dynamic routing (BGP) allows you to control path selection by advertising custom routes with different metrics (MED values) for the primary and backup paths. When the primary path is available, the lower metric route is preferred; if the BGP session fails, the route is withdrawn and traffic automatically fails over to the backup path with a higher metric. This meets the requirement for active/passive failover without manual intervention.

Answer

Configure Cloud NAT to route traffic through the backup path

Answer

Use static routes with a higher priority for the primary path

Answer

Create firewall rules to allow failover traffic

Question 8

An enterprise is using a 10 Gbps Dedicated Interconnect between their on-premises data center and Google Cloud. They measure throughput and find it is only 5 Gbps even though there is no congestion. The on-premises router is configured with a single VLAN attachment. What is the most likely cause?

Accepted Answer

The on-premises router does not support full line rate. A single VLAN attachment on a 10 Gbps Dedicated Interconnect means the on-premises router must handle all traffic through one physical interface. If the router lacks the forwarding capacity to process packets at 10 Gbps line rate, throughput will be capped at its maximum switching or routing performance, which in this case is 5 Gbps. This is a common hardware limitation, not a configuration or congestion issue.

Answer

BGP is not configured, causing routing loop

Answer

MTU mismatch between on-premises and Google Cloud

Answer

QoS policy is limiting throughput on Google Cloud side

Question 9

A company is planning to connect multiple VPCs in different regions to their on-premises network using a single Dedicated Interconnect. Which TWO configurations are required to achieve this?

Accepted Answer

Create a Cloud Router in each VPC. Option C is correct because each VPC requires its own Cloud Router to establish dynamic routing (BGP) over the Dedicated Interconnect. A Cloud Router is a per-VPC resource that manages BGP sessions and routes for that specific VPC, and since the interconnect is shared, each VPC must have its own router to participate in routing independently.

Answer

Create a single Cloud Router for all VPCs

Answer

Set up Cloud VPN tunnels for regional connectivity

Answer

Use a global VLAN attachment

Question 10

A company has a Hybrid Connectivity setup using Cloud VPN with BGP. They want to migrate to Dedicated Interconnect for better performance. During the migration, they need to avoid downtime. Which THREE steps should they take?

Accepted Answer

Provision the Dedicated Interconnect and VLAN attachments. Option C is correct because provisioning the Dedicated Interconnect and VLAN attachments is the foundational step to establish the new high-performance connection. Without this, there is no physical or logical path to migrate traffic onto. This must be done before any BGP configuration or route manipulation can occur.

Answer

Set a lower local preference on the Interconnect BGP session

Answer

Remove the VPN tunnels immediately after Interconnect is up

Question 11

A company is troubleshooting connectivity issues between their on-premises network and Google Cloud over a Dedicated Interconnect. They can ping the VLAN attachment IP but cannot reach Compute Engine instances. Which TWO checks should they perform?

Accepted Answer

Confirm that the subnet routes for the instance IP ranges are present in the VPC. Option B is correct because for on-premises traffic to reach Compute Engine instances over Dedicated Interconnect, the VPC must have a subnet route (either automatically created or custom static/dynamic route) that matches the instance IP ranges. Without this route, packets from the on-premises network will be dropped by the VPC router, even if the VLAN attachment is reachable.

Answer

Verify that the on-premises network has IAM permissions to access instances

Answer

Ensure that the VLAN attachment IP is in the same subnet as the instances

Answer

Check that BGP sessions are established between Cloud Router and on-premises router

Question 12

A company is using Cloud Interconnect with multiple VLAN attachments. They want to implement traffic shaping to prioritize real-time traffic over bulk transfers. Which THREE actions should they take?

Accepted Answer

Set up Cloud Router with BGP QoS policies to match DSCP values. Option A is correct because Cloud Router with BGP QoS policies can match DSCP values to prioritize traffic. By configuring BGP QoS policies, you can map specific DSCP values to different traffic classes, allowing Cloud Interconnect to apply traffic shaping that prioritizes real-time traffic (e.g., VoIP) over bulk transfers. This leverages BGP community attributes to signal QoS requirements across the hybrid connection.

Answer

Enable Cloud NAT to handle traffic shaping

Answer

Use VPC flow logs to identify heavy traffic flows

Question 13

Refer to the exhibit. The Cloud Router shows one BGP peer as ESTABLISHED and one as IDLE. The best routes show two routes to the same destination with different priorities. What is the most likely reason the IDLE peer is not establishing?

Accepted Answer

BGP configuration mismatch between Cloud Router and on-premises router for the IDLE peer. The IDLE state in BGP indicates that the session has not been established, typically due to a configuration mismatch. Since the Cloud Router shows one peer as ESTABLISHED and another as IDLE, the most likely cause is a mismatch in BGP parameters (such as AS number, peer IP, or authentication) between the Cloud Router and the on-premises router for the IDLE peer. This prevents the BGP session from transitioning out of the IDLE state.

Answer

The on-premises router is not sending routes for the IDLE peer

Answer

The IDLE peer has a higher priority route, so it is not needed

Answer

The IDLE peer is not configured on the Cloud Router

Question 14

A large e-commerce company has a hybrid cloud setup with a Dedicated Interconnect between their on-premises data center in Dallas and Google Cloud us-central1 region. They have a single VLAN attachment with a Cloud Router that uses BGP to exchange routes. The on-premises network uses 10.0.0.0/8, and Google Cloud VPC uses 172.16.0.0/16. They recently deployed a new application in us-west1 that uses IP range 172.17.0.0/16. They created a VPC peering between the us-central1 VPC and the us-west1 VPC. On-premises users can reach the us-central1 workloads but cannot reach the us-west1 application. There are no firewall rules blocking traffic. The on-premises router has a default route pointing to the Interconnect. What is the most likely cause of the issue?

Accepted Answer

The Cloud Router does not have routes for 172.17.0.0/16 because VPC peering does not automatically propagate routes to Cloud Router. The issue is that VPC peering does not automatically propagate routes from the peered VPC (us-west1, 172.17.0.0/16) to the Cloud Router that is used for the Dedicated Interconnect. Cloud Router only learns routes that are present in the VPC’s routing table and that are explicitly advertised via BGP. Since VPC peering routes are not automatically imported into the VPC’s dynamic routing table for Cloud Router, the on-premises router never receives a route for 172.17.0.0/16, even though there are no firewall blocks.

Answer

BGP is not configured between Cloud Router and us-west1 VPC

Answer

Firewall rules in us-west1 are blocking traffic from the on-premises IP range

Answer

The Dedicated Interconnect is only available in us-central1 and cannot reach us-west1

Question 15

A company needs to connect their on-premises data center to Google Cloud using Dedicated Interconnect. They have a service level agreement that requires 99.99% availability for the connection. What is the minimum number of VLAN attachments they must provision, and how should they be configured to meet this SLA?

Accepted Answer

Two VLAN attachments, each on a different Interconnect. To achieve 99.99% availability for Dedicated Interconnect, you must eliminate single points of failure. A single VLAN attachment on one Interconnect (Option A) provides no redundancy. Google Cloud requires at least two VLAN attachments, each on a different Interconnect (and ideally different edge availability domains), to meet this SLA. This ensures that if one Interconnect or VLAN attachment fails, traffic can fail over to the other, maintaining connectivity.

Answer

One VLAN attachment with a single Interconnect

Answer

Four VLAN attachments on two Interconnects

Answer

Two VLAN attachments on the same Interconnect