300-410 Bidirectional Forwarding Detection (BFD) — Timed 30 Questions

Question 1

A network engineer is troubleshooting an OSPF adjacency that is flapping between two routers. The adjacency forms and then drops repeatedly. Both routers are configured for BFD on the OSPF interface. The engineer checks the BFD session and sees it is up, but the OSPF neighbor state transitions from FULL to DOWN every few seconds. What is the most likely cause of this issue?

Accepted Answer

The OSPF dead interval is mismatched between the two routers.. The BFD session is up, so BFD is not causing the flap. The issue is likely a mismatch in OSPF parameters that causes the adjacency to reset independently of BFD.

Answer

The BFD timers are set too low on one router.

Answer

The interface is flapping due to a physical issue.

Answer

BFD is configured with the 'strict-mode' command, causing OSPF to ignore BFD state.

Question 2

A network engineer is troubleshooting a scenario where two routers running EIGRP are not forming an adjacency. Both routers have BFD configured under the EIGRP process and on the interfaces. The BFD session is up and operational. However, the EIGRP neighbor status shows 'Pending' and never transitions to 'Up'. What is the most likely cause?

Accepted Answer

The EIGRP K-values are mismatched between the two routers.. EIGRP requires the BFD session to be fully established before it will bring up the adjacency. If the BFD session is up but EIGRP is stuck in Pending, the issue is often a mismatch in EIGRP K-values or authentication.

Answer

The BFD timers are set too high, causing EIGRP to time out before BFD can respond.

Answer

EIGRP is configured with 'no auto-summary' on one router and 'auto-summary' on the other.

Answer

The interface is configured with 'bfd interval 50 min_rx 50 multiplier 3' but the neighbor expects different values.

Question 3

A network engineer is troubleshooting a BGP session that is dropping intermittently. The routers are connected via a Layer 2 switch. BFD is configured for the BGP session. The engineer notices that the BFD session goes down briefly, causing the BGP session to reset. The BFD timers are set to 100 ms interval with a multiplier of 3. The switch is not configured for BFD. What is the most likely cause?

Accepted Answer

The BFD timers are too aggressive for the switch's processing capabilities, causing BFD packets to be dropped during high traffic.. BFD sessions can be affected by congestion or processing delays in the Layer 2 switch, especially with aggressive timers. The switch not supporting BFD does not inherently cause issues, but high CPU or buffer drops can cause BFD packets to be dropped.

Answer

The BGP session is not configured with the 'bfd' command under the neighbor statement.

Answer

The switch is running Spanning Tree Protocol (STP) and causing delays.

Answer

One router has 'bfd slow-timers' configured, causing a mismatch.

Question 4

A network engineer is troubleshooting an OSPF adjacency that fails to come up. Both routers are directly connected via a serial link. BFD is enabled on the interface. The engineer sees that the BFD session is down. The OSPF configuration shows 'ip ospf bfd' under the interface. The serial interface is up/up. What should the engineer check first?

Accepted Answer

Verify that the 'bfd' command is configured under the OSPF process.. BFD on serial interfaces often requires the 'bfd interval' command to be explicitly configured, as the default may be disabled. Also, serial interfaces may need the 'bfd' command under the routing protocol as well.

Answer

Check if the serial interface is configured with 'encapsulation ppp'.

Answer

Ensure that the 'ip ospf bfd' command is also configured on the neighbor router.

Answer

Verify that the serial interface clock rate is set correctly.

Question 5

A network engineer is troubleshooting a BGP session that is not establishing. The routers are connected via a Layer 3 switch. BFD is configured for BGP. The engineer checks the BFD session and sees it is 'Down'. The BGP configuration appears correct. The interface between the routers is up/up. What is the most likely cause?

Accepted Answer

The BGP neighbor is not directly connected; BFD requires a directly connected interface or a static route pointing to the neighbor's IP.. BFD sessions require that the destination IP address be reachable via a directly connected interface or a static route. If the BGP neighbor is not directly connected (e.g., via a loopback), BFD may fail if the next hop is not directly connected or if there is a routing issue.

Answer

The Layer 3 switch is not configured for BFD, causing it to drop BFD packets.

Answer

The BGP session is using EBGP multihop, and the TTL is set to 1.

Answer

The interface is configured with 'bfd interval 50 min_rx 50 multiplier 3' but the neighbor is not configured for BFD.

Question 6

A network engineer is troubleshooting an OSPF adjacency that is not forming. Both routers are running OSPF with BFD enabled. The engineer checks the BFD session and sees it is 'Up'. However, the OSPF neighbor state is stuck in 'INIT'. What is the most likely cause?

Accepted Answer

The OSPF area ID is mismatched between the two routers.. OSPF stuck in INIT usually indicates that the router is not receiving OSPF hello packets from the neighbor. BFD being up suggests Layer 2 connectivity is fine, so the issue is likely OSPF configuration, such as a mismatch in area ID or authentication.

Answer

The OSPF hello interval is mismatched between the two routers.

Answer

The OSPF network type is mismatched (e.g., broadcast vs point-to-point).

Answer

The interface is configured with 'ip ospf bfd' but the OSPF process is not configured with 'bfd all-interfaces'.

Question 7

A network engineer is troubleshooting a scenario where BFD sessions are not forming between two routers running IS-IS. Both routers have BFD configured under the IS-IS process and on the interfaces. The engineer checks the BFD session and sees it is 'Down'. The IS-IS adjacency is up and operational. What is the most likely cause?

Accepted Answer

The BFD session is using the wrong source IP address; IS-IS BFD requires the interface IP to be used.. IS-IS BFD requires that the BFD session be established on the same interface as the IS-IS adjacency. If the IS-IS adjacency is up but BFD is down, the issue is often that the BFD configuration is not applied to the correct interface or that the BFD timers are not compatible.

Answer

The IS-IS process is configured with 'bfd all-interfaces' but the interface is not configured with 'isis bfd'.

Answer

The IS-IS metric is set to a high value, causing BFD to be ignored.

Answer

The interface is configured with 'bfd interval 50 min_rx 50 multiplier 3' but the neighbor is not configured for BFD.

Question 8

A network engineer is troubleshooting a BGP session that is flapping. The routers are connected via a direct Ethernet cable. BFD is configured for the BGP session. The engineer checks the BFD session and sees it is 'Up'. However, the BGP session goes down every 30 seconds. The BGP configuration includes 'neighbor 10.0.0.2 fall-over bfd'. What is the most likely cause?

Accepted Answer

The BGP hold timer is set to 30 seconds on one router and 90 seconds on the other.. The BGP fall-over bfd command causes BGP to monitor the BFD session. If the BFD session is up but BGP is flapping, the issue is likely a BGP configuration problem, such as a mismatch in hold timer or update-source.

Answer

The BFD session is using echo mode, which is not supported for BGP fall-over.

Answer

The interface is configured with 'bfd interval 50 min_rx 50 multiplier 3' but the neighbor is configured with 'bfd interval 100 min_rx 100 multiplier 3'.

Answer

The BGP session is using EBGP multihop, and the TTL is set to 2.

Question 9

A network engineer is troubleshooting an EIGRP adjacency that is not forming. Both routers are configured for EIGRP with BFD. The engineer checks the BFD session and sees it is 'Down'. The interface between the routers is up/up. The EIGRP configuration appears correct. What is the most likely cause?

Accepted Answer

The BFD timers are configured with 'bfd interval 50 min_rx 50 multiplier 3' on one router and 'bfd interval 100 min_rx 100 multiplier 3' on the other, causing a negotiation failure.. EIGRP BFD requires that the BFD session be established before the EIGRP adjacency can form. If the BFD session is down, the issue is often a mismatch in BFD parameters or a lack of BFD configuration on one side.

Answer

The EIGRP process is configured with 'bfd all-interfaces' but the interface is not configured with 'eigrp bfd'.

Answer

The interface is configured with 'ip address 10.0.0.1 255.255.255.252' but the neighbor is using a different subnet.

Answer

The EIGRP autonomous system number is mismatched between the two routers.

Question 10

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            1500(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 1500(0)
Rx Count: 120, Tx Count: 150

Based on this output, which statement is correct?

Accepted Answer

The BFD session is up and the holddown timer is 1500 ms, which is correct based on the configured multiplier and MinRxInt.. The output shows BFD session details. The Holddown value of 1500 ms is calculated as MinRxInt * Multiplier (1000 ms * 3 = 3000 ms), but the output shows 1500 ms. This discrepancy indicates a misconfiguration or a bug, but the key point is that the session is UP and the holddown timer is 1500 ms, which is half of the expected value. However, the correct interpretation is that the BFD session is established and operating, and the holddown timer is 1500 ms as shown.

Answer

The BFD session is down because the holddown timer is incorrect.

Answer

The BFD session is using echo mode, which is why the holddown timer is 1500 ms.

Answer

The BFD session is up but the multiplier is set to 1, causing the holddown timer to be 1500 ms.

Question 11

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Down          0(0)          Gi0/0

Session state is DOWN
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 1, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 0(0)
Rx Count: 0, Tx Count: 50

Based on this output, what is the most likely cause of the BFD session being down?

Accepted Answer

The BFD session is down because the neighbor is not responding to BFD packets, likely due to a network connectivity issue or neighbor misconfiguration.. The Local Diag field shows 1, which indicates 'Control Detection Time Expired'. This means the local router did not receive BFD control packets from the neighbor within the expected time. The Rx Count is 0, confirming no packets were received. Tx Count is 50, so the local router is sending packets but not receiving any.

Answer

The neighbor router is not configured for BFD.

Answer

The BFD session is down because the local router is not sending BFD packets.

Answer

The BFD session is down because the multiplier is set too low.

Question 12

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 150, Tx Count: 150
Echo function: Active

Based on this output, which statement is correct?

Accepted Answer

The BFD session is using echo mode, which reduces the load on the control plane because echo packets are processed in hardware.. The output shows that the BFD session is up and using echo function. The echo function allows faster failure detection by sending echo packets that are looped back by the neighbor. The holddown timer is 3000 ms, which is consistent with MinRxInt * Multiplier = 3000 ms. The Rx and Tx counts are equal, indicating bidirectional communication.

Answer

The BFD session is using echo mode, but the holddown timer is incorrect because echo mode should halve the timer.

Answer

The BFD session is up, but the echo function is not working because Rx and Tx counts are equal.

Answer

The BFD session is up and using echo function, but the neighbor must also have echo mode enabled for it to work.

Question 13

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 500000, Received Multiplier: 3
Holddown (hits): 1500(0)
Rx Count: 200, Tx Count: 200

Based on this output, what is the holddown timer value in milliseconds and why?

Accepted Answer

The holddown timer is 3000 ms, but the output shows 1500 ms because the holddown timer displayed is half of the actual holddown time.. The holddown timer is calculated as the maximum of the local MinRxInt and the received MinRxInt, multiplied by the multiplier. Local MinRxInt is 1000000 microseconds, received MinRxInt is 500000 microseconds. The maximum is 1000000 microseconds. Multiplied by 3 gives 3000000 microseconds = 3000 ms. However, the output shows 1500 ms. This is because the holddown timer displayed is actually half of the calculated value due to a Cisco implementation detail where the holddown timer is divided by 2 for display purposes. The actual holddown time is 3000 ms.

Answer

The holddown timer is 1500 ms, which is the received MinRxInt (500 ms) multiplied by the multiplier (3).

Answer

The holddown timer is 1500 ms, which is the local MinRxInt (1000 ms) multiplied by the multiplier (3) divided by 2.

Answer

The holddown timer is 3000 ms, and the output is correct as is.

Question 14

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 100, Tx Count: 100

Based on this output, what is the BFD session's negotiated transmit interval?

Accepted Answer

The negotiated transmit interval is 1000 ms.. The negotiated transmit interval is the maximum of the local MinTxInt and the received MinRxInt. Local MinTxInt is 1000000 microseconds, received MinRxInt is 1000000 microseconds. The maximum is 1000000 microseconds, which is 1000 ms. The BFD session will transmit control packets every 1000 ms.

Answer

The negotiated transmit interval is 500 ms.

Answer

The negotiated transmit interval is 3000 ms.

Answer

The negotiated transmit interval is 100 ms.

Question 15

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 100, Tx Count: 100

Based on this output, what is the BFD session's negotiated receive interval?

Accepted Answer

The negotiated receive interval is 1000 ms.. The negotiated receive interval is the maximum of the local MinRxInt and the received MinTxInt. However, the output does not show the received MinTxInt directly. The received MinRxInt is shown, but the receive interval is determined by the local MinRxInt. The local MinRxInt is 1000000 microseconds, so the router can receive BFD packets at intervals of 1000 ms or slower. The negotiated receive interval is typically the local MinRxInt, which is 1000 ms.

Answer

The negotiated receive interval is 500 ms.

Answer

The negotiated receive interval is 3000 ms.

Answer

The negotiated receive interval is 100 ms.

Question 16

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 100, Tx Count: 100

Based on this output, what is the BFD session's detection time?

Accepted Answer

The detection time is 3000 ms.. The detection time is the holddown timer, which is the negotiated transmit interval multiplied by the multiplier. The negotiated transmit interval is 1000 ms (maximum of local MinTxInt and received MinRxInt), and the multiplier is 3, so the detection time is 3000 ms.

Answer

The detection time is 1000 ms.

Answer

The detection time is 1500 ms.

Answer

The detection time is 9000 ms.

Question 17

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 100, Tx Count: 100

Based on this output, what is the BFD session's local discriminator?

Accepted Answer

The local discriminator is 1.. The local discriminator is the LD value shown in the output. In this case, it is 1.

Answer

The local discriminator is 3.

Answer

The local discriminator is 10.1.1.1.

Answer

The local discriminator is 10.1.1.2.

Question 18

A network engineer runs the following command on Router R1:

R1# show bfd neighbors detail

IPv4 Sessions
NeighborAddr      LD/RD         Int        State         Holdown(mult)  Intf
10.1.1.2          1/3           Gi0/0      Up            3000(3)        Gi0/0

Session state is UP and not using echo function.
OurAddr: 10.1.1.1
Handle: 1
Local Diag: 0, Demand mode: 0, Poll bit: 0
MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
Received MinRxInt: 1000000, Received Multiplier: 3
Holddown (hits): 3000(0)
Rx Count: 100, Tx Count: 100

Based on this output, what is the BFD session's remote discriminator?

Accepted Answer

The remote discriminator is 3.. The remote discriminator is the RD value shown in the output. In this case, it is 3.

Answer

The remote discriminator is 1.

Answer

The remote discriminator is 10.1.1.2.

Answer

The remote discriminator is 10.1.1.1.

Question 19

Consider the following partial configuration on a router:

interface GigabitEthernet0/1
 ip address 10.1.1.1 255.255.255.252
 bfd interval 100 min_rx 100 multiplier 3
!
router ospf 1
 network 10.1.1.0 0.0.0.3 area 0
!

What is the effect of this configuration?

Accepted Answer

BFD is configured on the interface but will not be used by OSPF unless the 'bfd all-interfaces' command is added under router ospf.. The BFD configuration is applied under the interface, but OSPF must be explicitly configured to use BFD via the 'bfd all-interfaces' command under the OSPF routing process. Without this, BFD will not be used for OSPF neighbor failure detection.

Answer

BFD is enabled for OSPF on this interface and will detect failures faster than OSPF's hello/dead timers.

Answer

BFD will only be used if the neighbor also has BFD configured with the same timer values.

Answer

The BFD configuration is invalid because the interval and min_rx values must be identical on both sides.

Question 20

Examine the following configuration:

interface GigabitEthernet0/0
 ip address 192.168.1.1 255.255.255.0
 bfd interval 50 min_rx 50 multiplier 5
!
router eigrp TEST
 network 192.168.1.0
 bfd interface GigabitEthernet0/0
!

Which statement is true about BFD operation on this interface?

Accepted Answer

BFD will detect a failure in 250 ms (5 x 50 ms).. The 'bfd interface' command under EIGRP enables BFD for that specific interface. The BFD session will negotiate timers; the multiplier of 5 means the session will declare a neighbor down after 5 * max(min_rx, negotiated interval) = 5 * 50 = 250 ms of missed packets.

Answer

BFD will detect a failure in 50 ms because the interval is set to 50 ms.

Answer

BFD is enabled but only for EIGRP; it will not affect any other routing protocol.

Answer

The configuration is missing 'bfd all-interfaces' under EIGRP, so BFD will not work.