220-1101 Cabling — Timed 10 Questions

Question 1

A customer reports that their new Gigabit Ethernet connection is only achieving 100 Mbps speeds. The cable run is about 75 meters through a drop ceiling. You verify the switch and NIC are both Gigabit-capable. Which cable issue is most likely causing the speed limitation?

Accepted Answer

The cable is a Cat5 cable.. This question tests knowledge of Ethernet cabling standards and speed limitations. Cat5e and Cat6 cables support Gigabit Ethernet up to 100 meters, but using an older Cat5 cable (which only supports 100 Mbps) will cap the speed. The correct answer identifies the cable category as the likely culprit.

Answer

The cable is a Cat5e patch cable.

Answer

The cable is a Cat6a cable.

Answer

The cable is a Cat6 cable.

Question 2

A customer wants to connect two switches in different buildings about 150 meters apart. The link must support at least 1 Gbps. Which cabling solution is most appropriate?

Accepted Answer

Single-mode fiber optic cable.. This question tests the understanding of Ethernet distance limitations and when to use fiber optic cabling. Copper Ethernet (Cat6) is limited to 100 meters, so a 150-meter run requires fiber optic cable, which can support Gigabit speeds over longer distances. The correct answer identifies fiber as the solution.

Answer

Cat6a copper cable.

Answer

Cat5e copper cable with a repeater.

Answer

Coaxial cable with a balun.

Question 3

A technician is troubleshooting a network where one workstation intermittently loses connectivity. The cable run is 85 meters and passes through a conduit with several sharp bends. The cable tester shows intermittent shorts. Which cabling issue is most likely?

Accepted Answer

The cable is being pinched or crushed in the conduit.. This question tests understanding of physical cable damage due to improper installation. Sharp bends can exceed the cable's bend radius, causing internal wire damage or shorts. The correct answer identifies this as the root cause.

Answer

The cable is too long for the network standard.

Answer

The cable is unshielded and picking up EMI.

Answer

The cable is a flat patch cable used for a permanent run.

Question 4

A technician is installing a new network drop in a warehouse where the cable must run near high-voltage machinery. The run is 60 meters. Which type of cable should be used to minimize interference?

Accepted Answer

STP Cat6a cable.. This question tests understanding of shielded cabling and its application in high-EMI environments. STP (shielded twisted pair) reduces electromagnetic interference, making it suitable for runs near machinery. The correct answer emphasizes the shielding benefit.

Answer

UTP Cat6 cable.

Answer

Coaxial RG-6 cable.

Answer

Fiber optic cable.

Question 5

A small office is installing new network drops in a drop ceiling for employee workstations. The IT manager wants to minimize future troubleshooting. Which cabling practice should be followed during installation?

Accepted Answer

Label both ends of each cable with a unique identifier.. This question tests best practices for structured cabling, specifically labeling and documentation. Proper labeling at both ends of each cable run simplifies future troubleshooting and maintenance. The correct answer emphasizes this fundamental practice.

Answer

Use crossover cables for all workstation connections.

Answer

Run cables parallel to electrical wiring to save space.

Answer

Use flat ribbon cables for all long runs.

Question 6

A customer reports that their new Cat6a installation passes a cable certifier test but the link only negotiates at 100 Mbps. The cable run is 90 meters and uses standard T568B terminations. What is the most likely cause of the speed limitation?

Accepted Answer

The patch cables are Cat5e instead of Cat6a.. This question tests advanced knowledge of cable certification and speed negotiation. A cable certifier tests for compliance, but if the cable passes, the issue may be with the patch cables or connectors, which can degrade performance even if the permanent link is good. The correct answer identifies the patch cables as the likely weak point.

Answer

The cable run exceeds the maximum length for Cat6a.

Answer

The switch port is configured for 100 Mbps only.

Answer

The cable is terminated in T568A instead of T568B.

Question 7

A user complains that their VoIP phone intermittently loses connectivity. The phone is connected to a switch via a 50-meter run of solid-core Cat6 cable. You suspect interference from nearby fluorescent lights. Which cabling characteristic is most relevant to this issue?

Accepted Answer

The cable is not shielded (STP).. This question tests understanding of electromagnetic interference (EMI) and how it affects network cabling. Unshielded twisted pair (UTP) cable is susceptible to EMI from sources like fluorescent lights, causing intermittent connectivity. The correct answer highlights the lack of shielding as the key factor.

Answer

The cable is not properly terminated with RJ45 connectors.

Answer

The cable length exceeds the maximum for Cat6.

Answer

The cable is a crossover cable.

Question 8

A technician is troubleshooting a network drop that was working yesterday but now has no link light at the switch. The cable run is 80 meters and passes through a conduit. Which tool should be used first to isolate the problem?

Accepted Answer

A cable tester.. This question tests the use of basic cable testing tools in a troubleshooting scenario. A cable tester can quickly identify faults like breaks, shorts, or miswiring. The correct answer prioritizes the most direct tool for the symptom.

Answer

A tone generator and probe.

Answer

A multimeter.

Answer

A time-domain reflectometer (TDR).

Question 9

A company is upgrading its network to support 10 Gbps connections between server racks. The distance between racks is 25 meters. Which cabling standard is most appropriate for this upgrade?

Accepted Answer

Cat6a cable.. This question tests knowledge of cabling standards for high-speed Ethernet. Cat6a is rated for 10 Gbps up to 100 meters, making it suitable for this distance. The correct answer distinguishes Cat6a from Cat6, which has shorter 10 Gbps support.

Answer

Cat5e cable.

Answer

Cat6 cable.

Answer

Cat7 cable.

Question 10

A user reports that their computer connected to a wall jack works fine, but when they move the computer to a different desk and plug into a different wall jack, there is no network connectivity. The switch port shows no link light. What is the most likely cause?

Accepted Answer

The wall jack is terminated incorrectly.. This question tests understanding of cable termination and wiring standards. A faulty termination at the wall jack or patch panel is a common cause of intermittent or no connectivity. The correct answer focuses on the physical connection at the new location.

Answer

The computer's NIC is faulty.

Answer

The patch cable is not a crossover cable.

Answer

The switch port is administratively down.