220-1201 Display Devices Troubleshooting — Timed 20 Questions

Question 1

A user's 4K monitor is set to 3840x2160 resolution but text and icons appear very small and blurry. The display cable is a standard HDMI cable. What is the most likely cause of the blurriness?

Accepted Answer

The HDMI cable does not support enough bandwidth for 4K resolution. Standard HDMI cables (especially older versions) may not have sufficient bandwidth for 4K at proper refresh rates, leading to chroma subsampling and blurry text. The correct answer identifies bandwidth limitation as the cause, and the solution would be to use a high-speed HDMI or DisplayPort cable.

Answer

The monitor's refresh rate is set too high

Answer

The graphics driver is corrupted

Answer

The monitor's scaling settings are incorrect

Question 2

A technician is setting up a dual-monitor workstation. One monitor is connected via DisplayPort, the other via DVI. The DVI monitor is not detected. The DisplayPort monitor works fine. Which of the following is the most likely cause?

Accepted Answer

The DVI cable is loose or the monitor is not powered on. Many graphics cards require that the DisplayPort monitor be the primary display or that the DVI port is disabled when a DisplayPort is active in certain configurations. However, the most common issue is that the DVI cable is not fully seated or the monitor is not powered on. The correct answer focuses on checking the DVI connection and power, as these are simple to verify.

Answer

The DVI port on the graphics card is faulty

Answer

The graphics card does not support mixed DisplayPort and DVI outputs

Answer

The DVI monitor's resolution is set too high

Question 3

A technician is troubleshooting a display that shows a single vertical line of dead pixels from top to bottom. The monitor is under warranty. Which of the following is the most appropriate resolution?

Accepted Answer

Replace the monitor under warranty. A vertical line of dead pixels indicates a defect in the LCD panel's column driver or bonding, which is a hardware failure. Unlike a few stuck pixels, this cannot be fixed by software or gentle pressure. The correct answer is to replace the monitor under warranty, as this is a manufacturing defect.

Answer

Use a pixel-fixing software to cycle colors rapidly

Answer

Gently massage the affected area with a soft cloth

Answer

Update the graphics card driver

Question 4

A user reports that their LCD monitor intermittently goes black for 2-3 seconds, then returns to normal. This happens randomly, not during any specific activity. The monitor's power LED stays green during the blackouts. Which component is most likely failing?

Accepted Answer

The monitor's backlight or inverter is failing. A green power LED during blackouts indicates the monitor is receiving power and signal, but the backlight is failing. Intermittent backlight failure is a common issue in aging CCFL or LED-backlit LCDs, often due to failing capacitors or inverter. The correct answer identifies the backlight or inverter as the culprit, as the display logic is still working.

Answer

The video cable is loose

Answer

The graphics card is overheating

Answer

The monitor's power supply is failing

Question 5

A customer complains that their LCD monitor has a persistent faint shadow of the previous image visible on the screen, even after changing applications. What is the most likely cause of this issue?

Accepted Answer

Image persistence due to static content. This describes image persistence or burn-in, common in LCD panels left on static images for extended periods. Unlike dead pixels or backlight issues, this is a temporary or permanent ghosting of static content. The correct answer identifies the root cause as static image retention, which can sometimes be reversed with screen refreshers.

Answer

A failing backlight inverter

Answer

A damaged video cable

Answer

Incorrect color calibration settings

Question 6

A technician is troubleshooting a desktop PC that powers on but shows no display on the monitor. The monitor's power LED is amber (standby). The PC has an integrated GPU and a discrete GPU. Which step should be taken FIRST to isolate the issue?

Accepted Answer

Check that the monitor cable is plugged into the discrete GPU, not the motherboard. An amber LED indicates the monitor is not receiving a signal. The most common oversight is connecting the cable to the wrong video port (motherboard vs. GPU). The correct first step is to verify the cable is connected to the discrete GPU's ports, as integrated graphics are often disabled when a dedicated card is installed.

Answer

Reseat the RAM modules

Answer

Replace the CMOS battery

Answer

Test the monitor on another computer

Question 7

A user reports that their external monitor connected via HDMI displays a 'No Signal' message, though the monitor power LED is lit. The laptop's built-in display works fine. Which of the following should be checked FIRST?

Accepted Answer

Ensure the HDMI cable is fully seated at both ends. This question tests the systematic approach to display troubleshooting. The monitor is powered on (LED lit) but not receiving a signal, so the most common cause is a loose or faulty cable connection. Always check physical connections before moving to more complex settings or hardware replacements, as this is the quickest and simplest fix.

Answer

Update the graphics driver

Answer

Replace the monitor

Answer

Adjust the screen resolution in Windows settings

Question 8

A user's projector displays a very dim image, even with the brightness setting at maximum. The lamp hour counter shows 1500 hours, and the projector is three years old. What is the most likely cause?

Accepted Answer

The projector lamp is reaching end of life. Projector lamps dim over time and typically need replacement after 2000-4000 hours. A dim image with max brightness and moderate lamp hours indicates the lamp is nearing end of life. The correct answer identifies lamp aging as the primary cause, not filters or cables.

Answer

The projector's air filter is clogged

Answer

The video cable is damaged

Answer

The input source is set to low brightness

Question 9

After installing a new graphics card, a user's display shows distorted colors and random artifacts during boot. The system POSTs successfully. Which of the following is the most likely cause?

Accepted Answer

The power supply unit is insufficient for the new card. Artifacts and color distortion after a new GPU install typically point to insufficient power delivery or a faulty card. Since the system POSTs, it's not a complete failure but likely a power or driver issue. The correct answer highlights that the power supply may not meet the card's requirements, causing instability.

Answer

The monitor is incompatible with the new card

Answer

The graphics card driver is outdated

Answer

The display cable is loose

Question 10

A user reports that their laptop screen flickers intermittently, but the flickering stops when they adjust the screen angle. What is the most likely hardware issue?

Accepted Answer

A loose or damaged display cable. Flickering that changes with screen angle is a classic symptom of a damaged or loose display cable (LVDS or eDP ribbon) that connects the screen to the motherboard. This is common in laptops due to hinge wear. The correct answer identifies the cable as the likely culprit.

Answer

A failing backlight LED

Answer

A defective graphics chip

Answer

Incorrect display refresh rate setting

Question 11

During a hardware installation, you connect a new 4K monitor to a desktop PC using DisplayPort, but the display is stuck at 1080p resolution. The graphics card supports 4K. What is the most likely cause?

Accepted Answer

The DisplayPort cable is not rated for 4K.. This question tests knowledge of display cable capabilities. DisplayPort cables come in different versions, and older cables may not support 4K at higher refresh rates. The most likely cause is using a DisplayPort cable that does not meet the required bandwidth for 4K.

Answer

The graphics card driver is outdated.

Answer

The monitor's refresh rate is set too high.

Answer

The monitor's input is set to HDMI.

Question 12

A user complains that their LCD monitor has a persistent dark spot in the center of the screen that does not change with different images. What is the most likely issue?

Accepted Answer

There is a stuck pixel.. This scenario describes a stuck or dead pixel, a common LCD defect. A dark spot that remains constant indicates a pixel that is not receiving power or is stuck in the off state. This is a hardware defect, not a software or connection issue.

Answer

The monitor's backlight is failing.

Answer

The graphics card is overheating.

Answer

The video cable is loose.

Question 13

A user reports that their laptop's built-in display shows a dim image that is barely visible even at maximum brightness. An external monitor works perfectly. The laptop uses an LED-backlit screen. What component is most likely failing?

Accepted Answer

The backlight LED driver is failing.. A dim display on a laptop with a working external monitor points to a backlight issue. In LED-backlit screens, the backlight is driven by an LED driver circuit on the display or motherboard. A failing backlight or its driver causes dimness while the LCD panel itself may still function.

Answer

The LCD panel is defective.

Answer

The inverter board is failing.

Answer

The graphics card is outputting a low signal.

Question 14

A technician is troubleshooting a display that shows a 'ghost' image of a previous screen that fades slowly. The monitor is a 4-year-old IPS panel. What is the most likely cause?

Accepted Answer

The LCD panel has image retention or burn-in.. Ghosting or image retention on an IPS panel is often due to burn-in or temporary image persistence. This occurs when static images are displayed for long periods, causing the liquid crystals to not fully relax. It is a hardware defect that may be irreversible.

Answer

The monitor's response time setting is too low.

Answer

The video cable is causing signal interference.

Answer

The monitor's refresh rate is set incorrectly.

Question 15

A technician is troubleshooting a display that shows vertical lines across the entire screen. The lines persist when a different video cable is used, and the monitor works fine when connected to another computer. What is the most likely cause?

Accepted Answer

The graphics card driver is corrupted.. Vertical lines that persist with different cables but disappear on another computer indicate a problem with the graphics card or its driver on the original computer. The monitor is proven good, so the issue is with the video source.

Answer

The monitor's panel is defective.

Answer

The video cable is damaged.

Answer

The monitor's refresh rate is set incorrectly.

Question 16

During a hardware upgrade, you install a new high-end graphics card and connect a 144Hz gaming monitor via DisplayPort. The monitor is set to 144Hz in Windows, but the screen occasionally goes black for a few seconds during gameplay. What is the most likely cause?

Accepted Answer

The monitor's refresh rate is set too high for the cable.. Intermittent black screens at high refresh rates often indicate that the DisplayPort cable does not meet the required bandwidth for 144Hz at the monitor's resolution. This can also be caused by power supply issues or driver problems, but cable bandwidth is a common culprit.

Answer

The graphics card is overheating.

Answer

The power supply unit is insufficient.

Answer

The monitor's firmware is outdated.

Question 17

A technician is configuring a dual-monitor setup for a financial analyst. Both monitors are identical 27-inch 1440p displays. After connecting them, one monitor shows a pink tint across the entire screen. What is the most likely cause?

Accepted Answer

The video cable is not fully seated or has a bent pin.. A pink tint on one monitor while the other looks normal suggests a loose or damaged video cable, specifically a missing blue color channel. VGA cables are prone to this, but even HDMI or DisplayPort cables can have pin issues. Swapping cables can confirm.

Answer

The monitor's color temperature is set incorrectly.

Answer

The graphics card driver is corrupted.

Answer

The monitor's backlight is failing.

Question 18

A user reports that their laptop screen flickers intermittently, especially when the lid is moved. The flickering stops when an external monitor is connected. What is the most likely cause?

Accepted Answer

The display cable is loose or damaged.. Intermittent flickering when moving the lid points to a loose or damaged display cable (LVDS or eDP) connecting the motherboard to the screen. The external monitor works because it bypasses this internal connection.

Answer

The graphics driver is outdated.

Answer

The inverter board is failing.

Answer

The LCD panel is failing.

Question 19

A customer reports that their external monitor connected via HDMI to a laptop shows a 'No Signal' message, even though the laptop screen works fine. The monitor has been tested with another device and works. What should you check first?

Accepted Answer

Press the function key to toggle display output.. This scenario tests basic display troubleshooting. The monitor works with another device, so the issue is likely with the laptop's video output or connection. The first step is to check if the laptop is set to output to the external display, often via a function key like F4 or F8.

Answer

Replace the HDMI cable.

Answer

Update the graphics driver.

Answer

Check the monitor's power cable.

Question 20

A customer brings in a desktop PC with a 4K monitor that displays a blurry image at native resolution. The monitor's settings show 3840x2160 resolution, but text is hard to read. What is the most likely issue?

Accepted Answer

The display scaling is set to 100%.. Blurry text at native resolution on a 4K monitor often indicates incorrect scaling settings in the operating system. Windows scaling should be set to 150% or 200% to make text readable, otherwise it appears too small and blurry due to pixel density.

Answer

The monitor's sharpness setting is too low.

Answer

The HDMI cable does not support 4K.

Answer

The graphics card is overheating.