Question 1mediummultiple choice
Full question →mediummultiple choiceObjective-mapped
A user's Android tablet was dropped and the glass digitizer cracked, but the LCD display still shows images correctly. The user reports that touch input is unresponsive in several areas of the screen. Which of the following replacement procedures is MOST appropriate?
Answer choices
Why each option matters
Good practice is not just finding the correct option. The wrong answers often show the exact trap the exam wants you to fall into.
A
Best answer
Replace the entire screen assembly (LCD and digitizer together)
The digitizer and LCD are fused in most tablets; replacing the assembly avoids further damage and ensures proper touch function.
B
Distractor review
Replace only the LCD display
The LCD is separate from the digitizer, but replacing it alone will not fix the broken digitizer. Touch would still be unresponsive.
C
Distractor review
Replace only the digitizer (touch panel)
Attempting to separate the digitizer from the LCD is difficult and often results in breaking the LCD. It is not recommended unless the manufacturer designed them as separate layers.
D
Distractor review
Perform a touchscreen recalibration
Calibration can fix alignment issues but cannot repair physical damage to the digitizer. The issue is hardware-related.
Common exam trap
Common exam trap: OSPF can fail even when IP connectivity looks correct
OSPF neighbour formation depends on matching areas, timers, network type, authentication and passive-interface behaviour. Do not choose an answer only because the devices can ping.
Technical deep dive
How to think about this question
OSPF questions usually test the details that control adjacency and route selection. Read the neighbour state, area, router ID and interface configuration before deciding what is wrong.
KKey Concepts to Remember
- OSPF neighbours must agree on key parameters.
- Router ID selection can affect neighbour relationships and LSDB output.
- OSPF cost influences the preferred path.
- A route can appear in OSPF information but not become the installed route.
TExam Day Tips
- Check area mismatch first when OSPF adjacency fails.
- Review passive interfaces when a network is advertised but no neighbour forms.
- Use show ip ospf neighbor and show ip route clues carefully.
Related practice questions
Related 220-1101 practice-question pages
Use these pages to review the topic behind this question. This is how one missed question becomes focused revision.
CompTIA A+ hardware practice questions
Practise 220-1101 questions linked to CompTIA A+ hardware.
CompTIA A+ mobile devices practice questions
Practise 220-1101 questions linked to CompTIA A+ mobile devices.
CompTIA A+ networking practice questions
Practise 220-1101 questions linked to CompTIA A+ networking.
CompTIA A+ operating systems practice questions
Practise 220-1101 questions linked to CompTIA A+ operating systems.
CompTIA A+ security practice questions
Practise 220-1101 questions linked to CompTIA A+ security.
CompTIA A+ software troubleshooting questions
Practise 220-1101 questions linked to CompTIA A+ software troubleshooting questions.
CompTIA A+ operational procedures questions
Practise 220-1101 questions linked to CompTIA A+ operational procedures questions.
More questions from this exam
Keep practising from the same exam bank, or move into a focused topic page if this question exposed a weak area.
Question 1
A user reports intermittent network connectivity on a desktop computer. The technician observes that the Ethernet link light on the NIC turns off for a few seconds and then turns back on. The cable passes a wiremap test, the switch port is verified good with another device, and the NIC driver is updated. The issue occurs more frequently when the computer's case fan runs at high speed. Which of the following is the MOST likely cause?
Question 2
A workstation is unable to connect to the internet. The technician runs the 'ipconfig' command and sees the IPv4 address is 169.254.15.200 with a subnet mask of 255.255.0.0. The workstation can ping other devices on the local subnet but cannot ping the default gateway or any external addresses. Which TWO actions should the technician take to resolve this issue? (Select two.)
Question 3
A workstation is connected to a managed switch. It obtains a valid IP address (192.168.10.50) from the DHCP server, but it cannot ping the default gateway (192.168.10.1). The link light on both the workstation NIC and the switch port are solid green. Other workstations on the same switch CAN ping the default gateway successfully. The technician accesses the switch management interface and finds that the workstation's port is configured as an access port on VLAN 10. The default gateway is located on VLAN 20. An inter-VLAN router is configured but not explicitly allowing VLAN 10 access to VLAN 20. Which of the following is the MOST likely cause of the problem?
Question 4
A company develops a web application that relies on a custom library available only for a specific Linux distribution. They want to deploy the application in the cloud with minimal administrative overhead, but they need full control over the software stack, including the ability to install the custom library and configure the web server. Which cloud service model BEST meets these requirements?
Question 5
A company has a legacy virtual machine running on a deprecated hypervisor (Hyper-V). They want to migrate this VM to a new hypervisor (VMware vSphere) hosted in a private cloud while preserving the VM's configuration, installed applications, and data. The migration must be performed with minimal downtime. Which of the following methods is MOST appropriate?
Question 6
A company hosts a critical database on a virtual machine in a public cloud. The database requires persistent storage that must be retained even if the VM is terminated. The storage must also be accessible from multiple VMs simultaneously for a future high-availability configuration. Which type of cloud storage BEST meets these requirements?
FAQ
Questions learners often ask
What does this 220-1101 question test?
OSPF neighbours must agree on key parameters.
What is the correct answer to this question?
The correct answer is: Replace the entire screen assembly (LCD and digitizer together) — In most modern tablets, the digitizer and LCD are fused together with optical adhesive. It is very difficult to separate them without damaging the LCD. Therefore, the best practice is to replace the entire screen assembly (LCD + digitizer). Replacing only the LCD or only the digitizer is impractical and risky. Touchscreen calibration will not fix physical damage to the digitizer.
What should I do if I get this 220-1101 question wrong?
Then try more questions from the same exam bank and focus on understanding why the wrong options are tempting.
Discussion
Loading comments…
Sign in to join the discussion.