vlan

Which TWO statements correctly describe interface errors and duplex mismatches on Cisco switches?

A network engineer is reviewing REST API behavior. Which two statements are true?

An API client sends a valid GET request and receives an HTTP 200 response. What does that indicate?

An interface is configured with 10.24.7.158/27. What is the broadcast address of that subnet?

Which three statements about the Spanning Tree Protocol (STP) are true? (Choose three.)

You are connected to R1 via the console. An extended ACL named BLOCK_SMTP has been applied inbound on interface GigabitEthernet0/1, but users on the 192.168.10.0/24 network cannot send email to the SMTP server at 203.0.113.10. Additionally, the ACL is blocking all other traffic that should be permitted. Examine the running configuration and fix the ACL so that SMTP traffic (TCP port 25) from the 192.168.10.0/24 network to the SMTP server is permitted, and all other IP traffic is allowed.

A router is configured as a DHCP server for VLAN 20. Clients on the VLAN can reach the default gateway, but they do not receive leases. Which two configuration issues on the router would directly prevent successful address assignment?

A switchport is configured with sticky MAC learning and a maximum secure MAC value of 2. What is the main benefit of sticky learning in this situation?

A switchport is configured for 802.1X authentication. What is the usual role of the RADIUS server in that design?

Refer to the exhibit. A network administrator is troubleshooting a trunk link between SW1 and SW2. The trunk on interface GigabitEthernet0/0 on SW1 is not passing traffic, and all VLANs are isolated. The administrator issues the command 'show interfaces GigabitEthernet0/0 trunk' on SW1. What is the most likely cause of the issue?

Which TWO statements correctly compare 802.11ac and 802.11ax features?

You are connected to R1. The network has two routers (R1, R2) and a switch (SW1) in between. R1's G0/0 connects to SW1 (192.168.1.1/24), SW1 connects to R2's G0/0 (192.168.1.2/24). R2 has a loopback (Lo0: 203.0.113.1/32) used as a management address. Configure an extended ACL on R1 so that only SSH (TCP/22) traffic from the 10.0.0.0/24 network is permitted to reach R2's loopback; all other traffic to that loopback must be denied. Then apply the ACL in the correct direction on the correct interface.

Match each API or programmability term to its most accurate meaning.

Drag and drop the following steps into the correct order to configure an IPv4 default static route with a floating backup route on a Cisco router.

Drag and drop the 802.11 standards on the left to their correct frequency band and maximum throughput on the right.

Drag and drop the AI/ML concepts on the left to the correct descriptions on the right.

Based on the exhibit, which route will be used for destination 10.1.1.70?

Port security is enabled with a maximum of 2 MAC addresses, but a third device connected through a small hub causes a violation. Which result is expected in restrict mode?

Refer to the exhibit. A network administrator configures NAT overload on R1 to allow internal hosts in the 10.1.1.0/24 subnet to access the Internet. After the configuration, the administrator runs the show ip nat translations verbose command and notices that several internal sessions all appear to use the same inside global port 1024. The administrator is concerned that port conflicts will occur. Based on the output, which statement is correct?

You are connected to R1. Configure IPv4 and IPv6 addressing on R1's GigabitEthernet0/0 and GigabitEthernet0/1 interfaces so that R1 can ping both R2's IPv4 address (203.0.113.2) and R2's IPv6 address (2001:db8:1::2). The current configuration has an incorrect subnet mask on G0/0, missing default gateway, and R1's G0/1 has a duplicate IPv4 address with R3. Also, use EUI-64 for IPv6 on G0/0 and static IPv6 assignment on G0/1. Ensure all issues are resolved and connectivity verified.

Match each common API or data term to its most accurate meaning.

An engineer wants rapid transition to forwarding on end-user switchports while still protecting the topology from accidental switch connections. Which two STP-related features fit that design?

You are connected to R1 via console. R1 and R2 are directly connected via their GigabitEthernet0/0 interfaces. Configure OSPFv3 for IPv6 on both routers so that the loopback0 interface on R2 (with IPv6 address 2001:db8:acad:2::1/64) is reachable from R1. Enable IPv6 unicast routing, enable OSPFv3 on the appropriate interfaces, and verify the neighbor adjacency and routing table. (Note: R2 already has OSPFv3 configured and is waiting for R1 to complete its configuration.)

Which TWO statements correctly describe the behavior of the passive-interface command in single-area OSPFv2?

What prefix length corresponds to the subnet mask 255.255.255.224?

A router has learned route 172.16.50.0/24 from OSPF with cost 20 and also has a static route to the same prefix with administrative distance 5. Which two statements are correct about route selection?

A network technician is troubleshooting a newly installed fiber link between two Cisco Catalyst 9300 switches. The link is up, but the interface shows excessive CRC errors and input errors. The technician runs 'show interfaces' and 'show interfaces transceiver details' on the suspect interface. Based on the output, what is the most likely cause of the errors?

Match each address-related concept to its most accurate meaning.

Based on the exhibit, why does the ACL still allow HTTPS traffic from the branch subnet to the server?

Match each data-structure term to its most accurate meaning.

Why is version control valuable for network automation files?

Which spanning-tree port state listens for BPDUs and participates in STP, but does not learn MAC addresses yet?

Which two statements accurately describe ACL behavior on Cisco devices?

A technician configures OSPF on R1 using the command network 10.0.0.0 0.0.0.255 area 0. R1's GigabitEthernet0/0 interface has IP address 10.0.0.1/30 and is included in the OSPF process. The technician confirms the interface is not passive using the show ip ospf interface GigabitEthernet0/0 command. However, R2 is not forming an OSPF adjacency with R1. What should the technician do next?

Which TWO statements are true about IPv6 link-local addresses?

A network administrator is troubleshooting a wireless connectivity issue in a large office. Users on the 5 GHz band report intermittent disconnections and slow performance, while 2.4 GHz clients are unaffected. The office uses a Cisco 9800 WLC with APs that support 802.11ac Wave 2. The administrator checks the WLC's RF profile and notices a high number of channel utilization reports on channel 36. What is the most likely cause of the problem?

Which two statements accurately describe JSON in network automation contexts?

A network engineer sends an HTTP GET request to a controller API and receives status code 401. What does that response indicate?

Drag and drop the following steps into the correct order to implement DHCP services for clients in VLAN 10 using a centralized DHCP server in VLAN 20 and to protect the network with DHCP snooping.

Which two statements accurately compare TCP and UDP? (Choose two.)

Exhibit: After a new switch was connected, the access-layer port went into err-disabled state immediately. Which feature most likely caused this?

Which two statements accurately describe Syslog in a Cisco network environment?

A network administrator notices that a switchport in access mode with PortFast enabled has transitioned to an err-disabled state. What is the most likely cause?

Which two statements accurately describe API authentication tokens? (Choose two.)

Which OSPF neighbor state indicates that the routers have already exchanged full link-state databases?

Which data format uses key-value pairs and is commonly returned by REST APIs?

A router interface applies this ACL inbound: 10 deny tcp any any eq 80 20 permit ip any any A user reports that web browsing to a server by IP address fails, but ping works. Which statement best explains the behavior?

You are connected to R1, a branch router that must synchronize time with the NTP server at 198.51.100.1 (reachable via G0/0) and send critical syslog messages (severity 0-4) to the logging server at 203.0.113.10. The current configuration has NTP pointing to a wrong server and syslog set to debug level, flooding the server. Correct the NTP server, set the NTP source interface to Loopback0 (10.10.10.1/32), and adjust the syslog trap level so that only emergencies through warnings are logged.

Two switches are connected by an 802.1Q trunk. CDP reports a native VLAN mismatch. Which issue is most likely to appear because of this?

Drag and drop the protocol/model on the left to the correct description on the right.

You are connected to the console of a Catalyst 2960+ switch named SW2. Configure the switch so that the IP phone connected to interface FastEthernet0/5 receives power via PoE and uses VLAN 150 for voice traffic, while the PC connected through the phone uses VLAN 50 for data. Additionally, the access point connected to interface FastEthernet0/10 must receive PoE and be placed in VLAN 100. Assume the interfaces are already correctly configured as access ports in VLAN 50 and VLAN 100, respectively. Verify your configuration using the appropriate show commands.

Why is version control useful for network automation scripts?

A route to 192.168.1.0/24 appears in the routing table from OSPF, but a more specific static route to 192.168.1.128/25 is also configured. Which route is used for traffic to 192.168.1.200?

A switch port connected to an edge host immediately transitions to forwarding and then later goes err-disabled after a BPDU is received. Which feature combination most likely produced this behavior?

A host address is 172.31.9.200/27. Which address is the first usable host in that subnet?

Two switches are connected by an 802.1Q trunk. Hosts in VLAN 30 cannot communicate across the link, but VLAN 10 works. What is the most likely cause?

A switchport connected to another switch should carry VLANs 10, 20, and 30. The interface is operational, but only VLAN 10 works. VLANs 20 and 30 fail. Which explanation is most likely if the port was accidentally configured as an access port in VLAN 10?

An engineer is troubleshooting an OSPF adjacency issue between two Cisco routers, R1 and R2, connected via GigabitEthernet0/0 on both sides. Hosts on R1's LAN cannot ping hosts on R2's LAN. The engineer checks the OSPF neighbor state on R1 and sees the adjacency is stuck in EXSTART/EXCHANGE. The router IDs are 1.1.1.1 on R1 and 2.2.2.2 on R2, and both routers have a network statement for their directly connected subnet. What is the most likely cause of this problem?

A network operations team is implementing an AI-driven automation system that uses an agentic AI agent to handle routine network issues. The agent is configured to detect high CPU utilization on a core router, then automatically execute a series of diagnostic commands and, if a specific pattern is found, trigger a configuration change to reduce load. After the change, the agent re-checks CPU utilization and, if still high, escalates the issue to a human engineer. Which of the following best describes the workflow being used?

Two switches should form an LACP EtherChannel. One side is configured passive, and the other side is also passive. What is the most likely result?

Drag and drop the following steps into the correct order to configure a Cisco IOS-XE router as a DHCP server for a client VLAN and then enable a DHCP relay agent on a different interface to forward client requests to a remote server.

You are connected to R1 via console. R1 and R2 are directly connected via GigabitEthernet0/0. Your task is to configure IPv4 and IPv6 addressing on both routers so that they can ping each other's IPv4 and IPv6 addresses. The current configuration has intentional faults: R1's IPv4 subnet mask is incorrect, R2 is missing its default gateway, and R1's IPv6 address uses EUI-64 but is not working due to a duplicate IP. Correct the IPv4 mask on R1, assign a static IPv6 address on R2, and ensure both routers can reach each other.

Which tool type is most appropriate for turning a variable set of interface values into a reusable configuration template?

A router learns route 198.51.100.0/24 from OSPF with AD 110 and also has a static route to the same prefix configured with AD 150. Which route is installed?

Based on the exhibit, which route will be used for destination 192.168.10.130?

Which three of the following are typical use cases for automation in network security operations? (Choose three.)

A network engineer replaces a failed 1000BASE-LX SFP on a core switch with a new transceiver of the same type. After connecting the single-mode fiber, the link remains down and a 'show interfaces gig1/0/49 transceiver' reveals an Rx power of –30 dBm, while the far-end SFP is transmitting at –3 dBm over a 2 km span. The fiber patch cord shows no visible damage.

R1 is not forming an OSPF adjacency with R2 on GigabitEthernet0/1. Which mismatch below is the most likely cause?

Which TWO statements correctly describe the behavior of Root Guard, Loop Guard, and BPDU Guard in a Rapid PVST+ environment?

Drag and drop the following steps into the correct order to troubleshoot a Windows client that is unable to reach a remote server.

A switchport is configured as an access port in VLAN 10, but a user plugs in a small unmanaged switch and connects multiple devices behind it. Which security feature most directly limits that behavior at the switchport?

A router has a static route for 172.16.10.128/25 and an OSPF-learned route for 172.16.10.0/24. When forwarding traffic to 172.16.10.130, why does the router use the static route instead of the OSPF route?

A router receives a destination prefix from EIGRP with administrative distance 90 and also from OSPF with administrative distance 110. The prefix length is identical. Which route source is preferred?

An administrator wants a switchport connected to an end device to move to forwarding quickly but does not want that setting used on inter-switch links. Which feature is intended for that edge-port behavior?

Drag and drop the following steps into the correct order to configure inter‑VLAN routing between VLANs 10 and 20, using a router‑on‑a‑stick with VLAN 99 as the native VLAN on the trunk link.

A network engineer notices that a switch port connected to a legacy server is experiencing late collisions and the server reports excessive retransmissions. The switch port is configured for auto-negotiation and shows a negotiated speed of 100 Mbps and duplex full. The server's NIC is manually set to 100 Mbps and half-duplex. What is the most likely cause?

A network administrator has configured dynamic NAT on a Cisco router to allow internal hosts to access the Internet. Internal hosts can ping external servers, but external hosts cannot initiate connections to any internal host. The administrator checks the NAT translations. What is the most likely cause of this behavior?

A security policy requires that only one management subnet be able to initiate SSH to a router. Which approach most directly supports that requirement?

A host receives its IP address automatically but cannot resolve hostnames. Which additional service information is most likely missing from its configuration?

A router learns the same destination prefix from OSPF and from a static route configured with administrative distance 90. Which route is preferred by default?

You are connected to R1 via console. R1 has two paths to the Internet: primary via ISP1 (G0/0) and backup via ISP2 (G0/1). The primary route has an administrative distance of 1, and the backup should only be used if the primary fails. Currently, both routes are active. You need to configure a floating static route for the backup.

Drag and drop the following steps into the correct order to send a RESTCONF GET request to retrieve interface configuration from a Cisco IOS-XE device and apply a configuration change based on the response.

In a REST-style API, which method is most commonly associated with retrieving information?

What is a main operational benefit of a controller-based networking architecture?

Which two statements accurately describe REST-based APIs in a network automation context?

A network technician replaced a faulty SFP transceiver on a switch port. After replacement, the port remains in a down/down state. The technician verifies the fiber cable is securely connected at both ends and observes that the remote switch port is also in a down/down state. What should the technician do next?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two redundant links to SW2 (G0/1 and G0/2). The network administrator wants to use both links for load balancing and redundancy by configuring EtherChannel. You need to configure a Layer 2 EtherChannel using LACP on both switches. The port-channel should be in VLAN 1.

Which THREE statements correctly describe the configuration and verification of NAT, PAT, and static NAT?

Match each automation-related term to the description that best fits it.

An engineer is troubleshooting an OSPFv3 adjacency issue between two routers R1 and R2 connected over a serial link. The link is up/up on both sides, and IPv6 is enabled on the interfaces. However, the 'show ipv6 ospf neighbor' command shows no neighbors. The engineer checks the OSPFv3 configuration. What is the most likely cause of the missing adjacency?

You are connected via the console to R1, a Cisco ISR 4331 router. The network administrator reports that the link between R1's GigabitEthernet0/0 and a switch is experiencing high error rates and intermittent connectivity. Upon inspection, you notice that the interface is configured with speed 1000 and duplex full. The switch port is set to auto-negotiate. Your task is to resolve the duplex mismatch by configuring the router interface to match the switch's settings.

What is a common requirement for interfaces to successfully bundle into an EtherChannel?

A host has the address 10.10.10.94/27. Which subnet contains that host?

Exhibit: A collector is receiving traffic metadata from a router, including source IP, destination IP, protocol, and byte counts. Which feature is being used?

Which TWO statements correctly describe the configuration and behavior of a router-on-a-stick setup for inter-VLAN routing?

You are connected to R1. Configure AAA with RADIUS authentication so that SSH users are authenticated first against the RADIUS server (198.51.100.10) and fall back to the local user database if the server is unreachable. Additionally, troubleshoot why an 802.1X-enabled interface (GigabitEthernet0/1) remains in the unauthorized state. The RADIUS server shares a key of 'cisco123' and uses UDP port 1812. The local user 'admin' with secret 'adminpass' must be available as a fallback.

Drag and drop the items on the left to match the descriptions on the right.

A junior network engineer is configuring a new Windows 10 workstation to connect to the corporate network. The network uses a /24 subnet mask and has a default gateway of 192.168.1.1. The workstation obtains its IP address automatically from a DHCP server, but the engineer needs to manually set a static IPv4 address of 192.168.1.50 and ensure the workstation can reach the internet. Which configuration step must the engineer take to satisfy these requirements?

Match each routing concept to its most accurate meaning.

You are connected to SW1. Configure an LACP EtherChannel between SW1 and SW2 using interfaces GigabitEthernet0/1 and GigabitEthernet0/2. The port-channel interface must be configured as a trunk allowing VLANs 10, 20, and 30. Currently, the channel is not forming due to a mismatch in speed/duplex and VLAN configuration on SW2. Troubleshoot and resolve the issue so that the EtherChannel comes up as a Layer 2 trunk.

Drag and drop the following steps into the correct order to configure IPv4 and IPv6 static routes, a default route, and a floating static route with higher administrative distance, then verify the routing tables.

A network engineer wants a static route to be used only when the OSPF-learned route disappears. Which configuration approach meets that goal?

Drag and drop the following steps into the correct order to capture and analyze traffic on IOS-XE using the embedded packet capture feature, and in Wireshark to isolate a Layer 2 or Layer 3 fault.

A subnet uses network address 192.168.200.96/28. Which range contains the usable host addresses?

A switch has DHCP snooping enabled, but users still experience IP-to-MAC spoofing attacks. Which additional feature should be considered to help address that specific problem?

A switch trunk must carry VLANs 10, 20, and 30, but traffic for VLAN 20 is failing. The trunk allowed list on one side is `10,30`. What is the most likely cause?

A switch port is configured with port security using these commands: switchport port-security switchport port-security maximum 1 switchport port-security violation restrict switchport port-security mac-address sticky A user unplugs a company laptop and connects a different unauthorized device. The interface stays up/up, but the new device has no connectivity. Which statement best explains what happened?

A host can reach remote websites by IP address but fails when using their hostnames. Which missing configuration item is the strongest suspect?

Drag and drop the following steps into the correct order to diagnose and resolve a duplex/speed mismatch causing interface errors on a Cisco switch.

What is the main purpose of this configuration? ipv6 route 2001:db8:100::/64 GigabitEthernet0/0

A client PC is receiving an APIPA address (169.254.x.x) instead of a valid IP from the DHCP server. The DHCP server is on the same subnet as the client. The technician runs the command 'show ip dhcp binding' and confirms that the correct scope is configured. The command 'show ip dhcp pool' shows that there are plenty of addresses remaining in the pool. The client's NIC status shows 'connected'. What should the technician do next?

A network administrator receives a call from a user who cannot access any external websites from their wired workstation. The user can ping the default gateway successfully, but fails to ping 8.8.8.8. The administrator runs ipconfig /all on the workstation and sees an IP address of 192.168.1.50, subnet mask 255.255.255.0, and default gateway 192.168.1.1. What is the most likely cause of this issue?

Two switches are bundled with LACP, but only one physical link is forwarding traffic in the port-channel. What is the most likely reason?

Which TWO of the following statements about Spanning Tree Protocol (STP) and Rapid PVST+ are true?

A switch port was configured for sticky MAC learning. Which two statements accurately describe how the feature behaves?

Match each REST API method to the action it most closely represents in a typical network automation workflow.

Which TWO interface error counters indicate a Layer 1 issue?

A network administrator has configured HSRP between RouterA and RouterB for VLAN 10. End hosts using the virtual IP 192.168.1.1 as their default gateway experience intermittent connectivity losses, and pings to 192.168.1.1 often fail. The output of 'show standby brief' on both routers shows the state as Active. What is the most likely cause?

Drag and drop the following steps into the correct order to configure AAA with a RADIUS server and enable 802.1X port authentication on an IOS-XE switch.

Match each REST or API concept to its most accurate description.

Match each common automation term to its most accurate meaning.

An administrator wants to allow HTTPS traffic from a source subnet to a server but deny all Telnet traffic from that same subnet to the same server. Which ACL capability is required to express that policy accurately?

A trunk link between two switches is up, but voice phones connected through one access switch no longer receive the correct voice VLAN treatment. Data users still pass traffic. Which area should be checked first?

A host is configured with 172.16.10.62/27. Which address is the broadcast address for that subnet?

Refer to the exhibit. A network administrator is reviewing the NAT translations on router R1 and notices that the internal host 192.168.1.10 appears in both a static NAT entry (for ports 80 and 443) using global address 203.0.113.10, and a dynamic PAT entry (port 49152) using global address 203.0.113.1. The administrator is concerned this might indicate a misconfiguration. Based on the output, which statement is correct?

A host uses the subnet mask 255.255.255.192. How many usable host addresses exist in each subnet?

R1 and R2 are directly connected. Their interfaces are up/up and belong to the same subnet. R1's OSPF configuration places the interface in area 0, while R2's interface is in area 1. R1 does not show R2 as an OSPF neighbor. What is the most likely cause?

A subnet uses the mask 255.255.255.252. How many usable host addresses are available in each subnet?

A switch port configured with PortFast and BPDU Guard receives a BPDU and transitions to an error-disabled state. Which statement best explains why this is considered useful protection?

Drag and drop the following steps into the correct order to plan, configure, and apply an extended ACL that permits only HTTP traffic from the 192.168.1.0/24 network to the server 10.0.0.10, applied inbound on interface GigabitEthernet0/1.

Which four of the following are best practices for securing network services and devices? (Choose four.)

Drag and drop the cable/transceiver types on the left to the correct descriptions on the right.

A subnet must support at least 126 usable IPv4 host addresses. Which prefix is the longest that meets the requirement?

Which TWO statements about HSRP active/standby election, priority, and preempt are true?

A JSON response from a controller contains a list of interfaces, each with its own name and status fields. Which JSON structure is most likely used to represent that list?

Drag and drop the following steps into the correct order to select and implement a network automation solution using the appropriate tool based on the use cases and differences between Puppet, Chef, Ansible, and Python.

Why is an extended ACL usually placed close to the source of the traffic being filtered?

R1 is an IPv6-only branch router. The administrator wants all unknown IPv6 destinations to be sent to the upstream router at 2001:db8:ff::1. Which command best achieves that goal?

Which two statements accurately describe why structured telemetry and APIs improve operational tooling?

You are connected to R1 via console. R1 must forward traffic to the 203.0.113.0/24 and 2001:db8:1::/48 networks through R2 (10.0.0.2/30, 2001:db8:ff::2/64). The primary path must use a next-hop of 10.0.0.2 for IPv4 and 2001:db8:ff::2 for IPv6. Additionally, configure a floating static default route for IPv4 that uses R3 (192.0.2.2/30) as a backup only when the primary path fails. The current configuration has errors: the IPv4 static route points to a wrong next-hop (10.0.0.5) and the primary default route is missing, causing the floating route (AD 100) to become active instead of serving as a backup. Fix these issues so that both primary and backup routes work correctly.

What prefix length corresponds to the subnet mask 255.255.255.248?

What is a key difference between SNMPv3 and earlier SNMP versions?

A network engineer notices that the system clock on a Cisco IOS-XE router is incorrect, causing syslog timestamps to be unreliable. The router is configured as an NTP client to synchronize with a remote NTP server at 192.168.1.10. However, the show ntp status command indicates the clock is unsynchronized. What is the most likely cause of this issue?

You are connected to R1. Configure HSRP on R1 and R2 so that R1 is the active gateway for VLAN 100 with a virtual IP of 192.0.2.254. R1 should preempt and track its G0/1 interface to decrement priority by 20 if it goes down. Currently, both routers show active for the group, and the virtual IP is incorrectly set. Troubleshoot and fix the configuration on R1 only.

A network engineer is configuring an EtherChannel between two switches. After applying the configuration, the port-channel fails to form. What is the most likely reason?

A network administrator notices that the NTP server on Router R1 is not synchronizing with the upstream NTP server at 192.0.2.1. The router is configured as an NTP client, but show ntp status indicates the clock is unsynchronized and the stratum is 16. There is no firewall between R1 and 192.0.2.1. What is the most likely cause of this issue?

In AAA, what does the second A stand for?

A host is configured with IP address 172.16.100.222/27. Which address is the broadcast address for its subnet?

You are connected to R1. Configure PAT (NAT overload) so that hosts on the 192.168.1.0/24 inside network can reach the Internet through the outside interface GigabitEthernet0/1 using the IP address 203.0.113.1. Additionally, configure static NAT to map internal server 192.168.1.10 to public IP 203.0.113.5. The current configuration has several errors. Identify and correct them.

You are connected to R1, a router that serves as the DNS resolver for the local network 192.168.10.0/24. Users report that they cannot resolve the hostname 'webserver.internal' to its IP address (192.168.10.50), and reverse DNS lookups for that IP return a different name. Additionally, some queries to an external domain 'example.com' time out. Diagnose and fix the DNS configuration on R1 using nslookup and dig commands where applicable, ensuring proper forward and reverse resolution for internal hosts and reachability to external DNS servers.

You are connected to a multilayer switch MLS1. Configure FastEthernet0/1 as an access port for an IP phone and a PC, with voice VLAN 20 and data VLAN 10. Also enable PoE on the port. Then verify the configuration using 'show interfaces switchport' and 'show power inline'.

A switch port is configured with port-security violation mode restrict. Which two statements are true when an unauthorized MAC address appears?

Which TWO commands would a network administrator use to verify that a client has received a valid IP address from a DHCP server and can resolve domain names to IP addresses?

A phone and PC share one switchport. The phone registers successfully, but the workstation receives an address from the wrong subnet. Which explanation is strongest?

Why does traffic to 172.31.80.10 use the RIP route (172.31.80.0/24) instead of the static route (172.31.0.0/16)?

Drag and drop the following troubleshooting steps into the correct order to diagnose a client connectivity issue using the OSI bottom-up method. The client cannot access a web server by its FQDN.

Which two statements accurately describe longest-prefix match in routing?

You are connected to R1. Configure R1 so that it uses a floating static route to reach the 203.0.113.0/24 network via R2 only when the primary route (learned via EIGRP) fails. The primary route has an administrative distance of 90. Currently, R1 has no route to 203.0.113.0/24 because EIGRP is down on the direct link. Ensure the floating static route is installed and used.

You are connected to R1 via console. R1 is a router that needs to provide DHCP services to hosts on VLAN 10 (192.168.10.0/24) and VLAN 20 (192.168.20.0/24). The router has two subinterfaces on GigabitEthernet0/0: G0/0.10 (192.168.10.1/24) and G0/0.20 (192.168.20.1/24) with 802.1Q encapsulation. Configure R1 as a DHCP server for both VLANs, excluding addresses 192.168.10.1-10 and 192.168.20.1-10, with a lease of 1 day. Ensure DNS server 8.8.8.8 is provided.

Which prefix length corresponds to the subnet mask 255.255.255.192?

After configuring a trunk port to allow VLAN 40, a technician finds that VLAN 40 is not listed among the VLANs in spanning tree forwarding state in the show interfaces trunk output. What is the most likely cause?

In a router-on-a-stick design, what is configured on the physical router interface connected to the switch?

A client on VLAN 20 must obtain an IPv4 lease from a DHCP server located on VLAN 100. Which feature is required on the Layer 3 interface for VLAN 20?

A static route is configured as 198.51.100.0/24 via 192.0.2.9, but the connected network to the next hop goes down. What happens to the static route in the routing table?

A network administrator is troubleshooting a user's wired workstation that cannot access the internet. The user reports that the workstation was working earlier today. The administrator runs 'ipconfig /all' on the workstation and sees an IP address of 169.254.10.55. What is the most likely cause of this issue?

Drag and drop the following OSPFv2 neighbor state transitions and DR/BDR election steps into the correct order for a multi-access network with default priority values.

Drag and drop the following steps into the correct order to capture and analyze traffic on IOS-XE using the embedded packet capture feature, then export to Wireshark to isolate a Layer 2 or Layer 3 fault.

When two routes to the same destination are learned by OSPF from different paths, what criterion does OSPF use to select the best path?

A switchport connected to a user workstation is placed in VLAN 30. The administrator also wants to prevent that port from learning more than one MAC address. Which feature should be configured?

PCs in VLAN 40 are not receiving addresses from the centralized DHCP server at 172.16.1.10. What should be configured on the VLAN 40 default gateway interface?

In a controller-based WLAN, what is the main job of the access point?

You are connected to R1 via console. Configure OSPFv3 for IPv6 on both R1 and R2 so that the loopback0 interface on R2 (IPv6 address 2001:db8:1:2::1/64) is reachable from R1. The link between R1 and R2 uses the subnet 2001:db8:1:1::/64 with R1's G0/0 having IPv6 address 2001:db8:1:1::1/64 and R2's G0/0 having 2001:db8:1:1::2/64. OSPFv3 process ID must be 100 and all interfaces must be in area 0. After configuration, verify OSPFv3 neighbors and the IPv6 route to the loopback0 network.

You are connected to the console of R1. The network administrator reports that users cannot communicate with the server at 192.168.2.10. R1 is connected to R2 via a serial link (S0/0/0) with IP 10.0.0.1/30 on R1 and 10.0.0.2/30 on R2. The network uses OSPF for routing. You suspect an interface issue on the serial link.

Which TWO statements accurately describe the encapsulation process in the TCP/IP model as data moves from the application layer to the network access layer?

You are connected to R1 via console. R1 and R2 are configured with EIGRP AS 100. R1's loopback0 (1.1.1.1/32) should be advertised into EIGRP. However, after configuration, R2 does not have a route to 1.1.1.1/32. You need to verify the EIGRP configuration on R1 and R2 to determine why the route is missing. Use show commands to identify the issue.

You are connected to R1 via console. R1's GigabitEthernet0/1 interface connects to a remote site switch over a 2 km fiber link. The current configuration shows speed and duplex set to 1000 Mbps and full, but the interface is down/down due to an SFP mismatch. Review the exhibit, identify the problem, and correct it so that the interface comes up and communicates at the correct speed and duplex. Additionally, ensure the interface is configured to auto-negotiate properly for future cable replacements.

A multilayer switch has SVIs for VLAN 10 and VLAN 20. Hosts in both VLANs can reach their local SVI, but they cannot reach each other. Which additional configuration is most likely required?

A router output shows this neighbor state: Neighbor ID 10.1.1.1 State FULL/DR Address 192.168.12.1 What does the FULL/DR state indicate?

An EtherChannel between SW1 and SW2 is not forming. The technician runs the show etherchannel summary command on both switches and sees that all configured interfaces are in the 'I' (stand-alone) state. Both switches have their interfaces configured with channel-group 1 mode active. What should the technician check next?

You are connected to R1. Configure static routes so that R1 can reach the IPv4 network 203.0.113.0/24 and the IPv6 network 2001:db8:acad:1::/64 via R2 (G0/0 10.0.0.2/30). Additionally, configure a floating static default route (IPv4) with an administrative distance of 200 via R2, and a fully specified IPv6 default route via R2. Then, verify that the IPv4 static route to 203.0.113.0/24 is correctly installed by checking the routing table. The current configuration has an incorrect next-hop causing recursive routing failure for the IPv4 static route.

Which ACL type can filter using source and destination IP addresses as well as TCP or UDP port numbers?

A technician is troubleshooting an OSPF adjacency problem: R1 and R2 are not forming a neighbor relationship. R1's OSPF configuration includes the command 'network 192.168.1.0 0.0.0.255 area 0'. R2's GigabitEthernet0/0 is configured with IP address 10.1.1.1/30 and is participating in OSPF area 0. The engineer verifies that physical connectivity is fine and OSPF is enabled on R2. What is the most likely cause?

A network engineer configures an EtherChannel between two Cisco switches SW1 and SW2 using LACP. After configuration, hosts connected to SW1 report intermittent connectivity to hosts on SW2. The engineer checks the EtherChannel status and sees that the trunk is up but only allows VLAN 1, while the hosts communicate across VLANs 10 and 20. Which command should the engineer apply to both switches to resolve the issue?

R1 and R2 are directly connected. Both are configured in OSPF area 0, and they can successfully ping each other. However, OSPF neighbor adjacency fails. R1's interface is configured with `ip ospf authentication message-digest` and a valid key, while R2's interface has no OSPF authentication configured. What is the most likely cause?

A router has both an OSPF route and a static route to the same destination. The static route has an administrative distance of 200. What is the expected behavior while the OSPF route remains available?

An administrator configured a floating static default route on R1 as a backup to reach 10.10.10.0/24. The primary path is learned via OSPF, and the floating static route uses an administrative distance of 130. After the primary OSPF neighbor fails, traffic to 10.10.10.0/24 is dropped. According to the exhibit, why is the backup default route not being used?

You are connected to R1. The network uses 192.168.1.0/24 for internal hosts and 203.0.113.0/29 for the public IP pool (203.0.113.2 is the outside interface). Configure PAT so that inside hosts can reach the Internet using the pool address 203.0.113.2. Also configure static NAT to map internal server 192.168.1.10 to 203.0.113.3. The initial config has errors; identify and fix them.

Exhibit: R1 shows an OSPF neighbor stuck in EXSTART with R2 on a serial link. What is the most likely cause?

A network administrator is troubleshooting a Windows 10 client that cannot access a web server at 192.168.1.100. The client has an IP address of 192.168.1.50/24 and can ping its default gateway (192.168.1.1) successfully, but ping to 192.168.1.100 fails. Which command should the administrator run next to verify the client's current network connections and identify potential issues with active sessions?

You are connected to R1. The network requires HSRP for default gateway redundancy on subnet 192.168.1.0/24. R2 should be the active router, and R1 the standby. Currently, both routers show as active. Configure R1 with priority 90, enable preempt, ensure the virtual IP is 192.168.1.254, and configure tracking of interface GigabitEthernet0/1 (subnet 203.0.113.0/30) so that if R1's tracked interface goes down, its priority decreases by 20. Verify the final state with 'show standby brief'.

Which WAN technology is most closely associated with establishing a direct point-to-point data-link connection between two routers over a serial link?

A REST API call uses the GET method against a device inventory endpoint. What is the most likely intent of the call?

A router is configured for NAT overload, but translations never appear when inside users browse the internet. Which issue is most likely?

What is version control primarily used for in network automation workflows?

A switch port connected to an end host should forward traffic for one VLAN only and should not negotiate trunking. Which configuration approach best fits that requirement?

Which TWO symptoms are most likely to appear in the output of 'show interfaces' when a duplex mismatch exists between a switch port and a connected host?

A packet destined for 10.1.1.130 arrives at the router. Based on the routing table, which route will be used?

You are connected to R1 via the console. R1 has two directly connected routers: R2 and R3. Currently, R1 cannot reach R2's loopback interface (203.0.113.1/32). Additionally, R3 is IPv6-only and must be reachable from R1 using a statically assigned global unicast address. Configure R1's interfaces and static routes so that: (1) R1 can ping R2's loopback, (2) R1 can ping R3's IPv6 address 2001:db8:acad:2::1/64, and (3) R1's IPv6 address on the link to R3 is derived using EUI-64.

A switch has DHCP snooping enabled and Dynamic ARP Inspection enabled on VLAN 30. A printer with a static IP on VLAN 30 cannot communicate because its ARP packets are being dropped. What is the best fix?

You are connected to R1. The network consists of three routers: R1, R2, and R3. R1 must reach the loopback network 203.0.113.0/24 on R3 via two paths: a primary static route through R2's G0/0 (192.0.2.2) and a floating static route through R2's G0/1 (198.51.100.2) with an administrative distance of 150. Additionally, R1 already has a default route pointing to 192.0.2.2. Configure the two static routes to 203.0.113.0/24 on R1 as described. The default route does not need to be changed. Verify that the primary route is active and the floating route is used only if the primary fails.

Which TWO statements about 802.1Q trunking, native VLANs, and inter-VLAN routing are correct? (Choose two.)

Refer to the exhibit. An administrator has configured NAT on router R1 to allow hosts on the 192.168.1.0/24 LAN to access the Internet. However, users report that they cannot reach external websites. The administrator runs the show ip nat translations command. What is the most likely reason for the problem?

You are connected to R1 via the console. The network operations center (NOC) has asked you to configure R1 as an NTP client of the NTP server at 192.0.2.10 (reachable via VLAN 100, SVI 192.168.1.1/24). They also need all system messages of level 'debug' (level 7) and higher forwarded to the syslog server at 203.0.113.50. The current configuration shows that NTP is not working (stratum 16) and syslog is only sending critical and higher messages. Fix both issues.

Drag and drop the following steps into the correct order to describe the encapsulation of data as it passes down the TCP/IP stack for transmission.

You are troubleshooting connectivity from R1 to the 203.0.113.0/24 network. R1 is a multilayer switch running routed ports. Currently, R1 has two paths to reach that network: one via R2 (192.0.2.2) and one via R3 (198.51.100.2). The path via R2 is preferred, but after a link failure between R1 and R2, traffic should automatically fail over to the R3 path. However, after the failure, traffic is still being sent to R2. Examine the routing table and configuration, then fix the issue so that the floating static route takes over correctly when the primary route is lost.

A host address is 192.168.22.145/28. Which subnet contains that host?

A host is configured with 10.10.10.130/25. What is the network address of its subnet?

What is a northbound API in a controller-based network architecture?

A client can join a corporate SSID and authenticate successfully, but it consistently loses connectivity when moving between floors. Which area is most strongly suggested for deeper investigation?

Which three of the following are characteristics of DHCP snooping? (Choose three.)

Which three of the following are key benefits of integrating AI into network operations? (Choose three.)

A network administrator configured dynamic NAT on a Cisco router to allow internal hosts to access the internet. After the configuration, users report that they can access some websites but not others. The administrator checks the router and discovers that the NAT translation table is full, and new connection attempts are being dropped. What is the most likely cause of this issue?

A router learns 10.10.10.0/24 from OSPF and EIGRP at the same time. OSPF reports a metric of 20, and EIGRP reports a metric of 30720. Which route is installed in the routing table by default?

A switchport is configured as an access port for VLAN 20, but users connected to it cannot reach the default gateway. The switch shows the interface as up/up. Which switch misconfiguration is the most likely cause?

Drag and drop the following steps into the correct order to isolate CRC errors, duplex mismatches, and flapping on a Cisco IOS-XE interface.

You are connected to R1 via the console. R1 connects two networks: GigabitEthernet0/0 (192.168.1.1/24) and GigabitEthernet0/1 (192.168.2.1/24). Create an extended ACL named BLOCK_HTTP that denies HTTP traffic (tcp port 80) from the 192.168.1.0/24 network to the 192.168.2.0/24 network, but permits all other IP traffic. Apply this ACL inbound on GigabitEthernet0/0.

R1 has the following routes installed: O 10.10.10.0/24 via 192.0.2.2 S 10.10.10.128/25 via 198.51.100.2 S* 0.0.0.0/0 via 203.0.113.1 A packet destined for 10.10.10.200 arrives at R1. Which route is used?

A security team wants device administrators to log in with individual named accounts instead of sharing one generic admin account. Which security objective does that most directly improve?

A router has a static default route with administrative distance 250 and also learns a default route through OSPF. What is the main design purpose of the static default route?

An administrator wants an access-layer interface to shut down immediately if another switch is connected accidentally. Which feature best meets that requirement?

A switch interface connects to a user PC and should belong only to VLAN 30. Which command assigns that VLAN after the interface is in access mode?

A router learns 10.0.0.0/8 from OSPF and 10.10.0.0/16 from a static route. Which route is used for traffic to 10.10.20.1?

PCs in VLAN 30 on SwitchA cannot reach PCs in VLAN 30 on SwitchB. VLAN 30 exists on both switches and all other VLANs work across the same link. Based on the exhibit, what is the most likely cause?

Exhibit: A controller returns an authentication token after a successful API login. Why does the client include that token in later requests?

A user types www.example.com into a browser. Which service is used first to resolve that name into an IP address?

You are troubleshooting a client connectivity issue on PC1, which is connected to switch SW1. PC1 reports that it cannot access the internet, but it can ping its default gateway (192.168.1.1). The network uses VLAN 10 for the client subnet. Examine the following show outputs: On PC1, ipconfig shows IP 192.168.1.10, default gateway 192.168.1.1, DNS server 192.168.1.1. On SW1, show running-config includes 'interface Vlan10' with IP 192.168.1.1 255.255.255.0, but no 'ip dns server' and no 'ip name-server' commands. SW1's show ip route displays a default route via 203.0.113.1. Identify the root cause. Configure the necessary fix on the appropriate device to restore full connectivity.

After securing a switch by running 'ip ssh version 2' and generating RSA keys with 'crypto key generate rsa modulus 1024', remote SSH connections fail with a 'key exchange error'. A check of the SSH client’s documentation reveals it requires a minimum 2048-bit RSA key for SSH version 2. What should the technician do next?

A router allows SSH management from anywhere on the internal network. A new policy requires that only the management subnet 10.50.50.0/24 be allowed to initiate SSH to the device. Which approach best enforces that requirement?

You are connected to SW1 via the console. The network uses Rapid-PVST+ and you need to ensure that SW1 becomes the root bridge for VLAN 10 and VLAN 20. Additionally, configure PortFast and BPDU Guard on interface GigabitEthernet0/1, which connects to a workstation. After configuration, the workstation is moved and the port goes err-disabled. Diagnose the cause and recover the port without reloading the switch.

Drag and drop the following steps into the correct order to determine the best route to a destination using a routing table.

A network technician is troubleshooting a connectivity issue for a PC connected to switch port Gi1/0/12. The PC can ping its default gateway (192.168.10.1) but cannot ping a server at 192.168.20.10. The switch is configured with VLAN 10 for the access port and is connected to a router-on-a-stick. The technician runs 'show vlan brief' and 'show interfaces trunk' on the switch. What is the most likely cause of the problem?

Which TWO statements correctly describe EtherChannel configuration and verification with LACP?

What is the operational purpose of configuring the IPv6 route ::/0?

A router has routes to 10.50.0.0/16, 10.50.10.0/24, and 10.50.10.128/25. Which route is used for traffic to 10.50.10.140?

A network administrator is troubleshooting a connectivity issue between two remote sites connected via a WAN link. Hosts on VLAN 10 at Site A (192.168.10.0/24) cannot ping the server at Site B (10.10.20.100). The router at Site A has a default route configured with the next-hop IP address 10.10.10.2. The administrator checks the routing table on Router A and notices that the default route is not installed. What is the most likely cause of the problem?

You are connected to a Multilayer Switch MLS1. Configure the switch so that interface GigabitEthernet1/0/1 is an access port for VLAN 10, with voice VLAN 110 for an IP phone, and enable PoE. Additionally, interface GigabitEthernet1/0/2 must be an access port for VLAN 20 to connect an AP. Verify the configuration using 'show interfaces switchport' and 'show power inline'.

Drag and drop the following steps into the correct order to describe the TCP three-way handshake process between a client and a server.

A host is configured with IP address 10.10.40.78/28. Which subnet contains that host?

Match each REST-style method to the action it most commonly represents.

A branch router has only one WAN link connected to an Ethernet handoff from the provider. Which static default route is generally the better choice?

A named standard ACL is configured to permit only the 192.168.30.0/24 subnet, but users from 192.168.31.0/24 are still passing traffic. What is the most likely reason?

A company wants to reduce the chance that unused switch ports can be exploited. Which action best aligns with that goal?

A network technician notices CDP native VLAN mismatch warnings between switches SW1 and SW2 on their trunk link. The technician runs 'show interfaces trunk' on SW1 and sees native VLAN 1, then on SW2 and sees native VLAN 99. Data traffic is currently passing, but the mismatch can cause broadcast loops. What should the technician do next?

A host is configured with 192.168.60.33/26. Which address is the network address of its subnet?

Which TWO statements accurately describe the use of packet capture tools for troubleshooting Layer 2/3 issues?

You are connected to R1 via console. R1 is a router that has two paths to the Internet: one via ISP1 with next-hop 203.0.113.1, and a backup via ISP2 with next-hop 203.0.113.2. The primary path should be via ISP1, but if it fails, traffic should automatically use ISP2. Currently, R1 has a static default route to ISP1 only. You need to configure a floating static route to ISP2 with an administrative distance of 150 to provide backup connectivity. Additionally, you must ensure that the backup route is only used when the primary route is not available.

Which three statements are true about the operation of Dynamic Host Configuration Protocol (DHCP) in an enterprise network? (Choose three.)

You are troubleshooting a wireless client connectivity issue on the Cisco WLC at 192.168.1.100. The client reports it can see the SSID 'CorpNet' and successfully associates, but cannot obtain an IP address or reach network resources. The WLAN is already configured with WPA3 security, and the SSID should remain hidden. Identify and correct the configuration issue.

Drag and drop the following steps into the correct order to configure an LACP EtherChannel on two Cisco switches using active mode.

Match each switching feature to its most accurate purpose.

Which two statements accurately compare SLAAC and DHCPv6?

Which wireless security method is considered strongest among these choices for modern enterprise WLAN deployments?

You are connected to R1. The network currently permits all HTTP traffic from hosts on the 192.168.1.0/24 LAN to reach the web server at 203.0.113.10, but SSH traffic (TCP port 22) from the same LAN is being blocked. Additionally, you must ensure that no other traffic from the LAN reaches the server. Configure an extended ACL on R1 to allow only HTTP and SSH from the LAN to the server, and apply it inbound on the correct interface. Verify your solution.

A host is configured with 10.10.10.33/27. What is the broadcast address of its subnet?

You are connected to R1 via console. R1 is connected to R2 via GigabitEthernet0/0 and to R3 via GigabitEthernet0/1. OSPF has been configured, but R1 is not forming a full adjacency with R2. You run `show ip ospf neighbor` on R1 and see R2 stuck in EXSTART state. You also run `show ip ospf interface GigabitEthernet0/0` and see the network type is broadcast. You need to identify and resolve the issue.

Drag and drop the wireless terms on the left to the correct descriptions on the right. Options: A: SSID: The network name broadcast by an access point to identify the wireless network. B: BSSID: The MAC address of the access point's radio interface, used to uniquely identify a BSS. C: RSSI: A measurement of the power level of the received radio signal, indicating signal strength. D: DFS: A mechanism that allows wireless devices to avoid interference with radar systems by dynamically selecting channels.

A host reaches websites by IP address but fails when using hostnames. Which service is the strongest suspect?

Exhibit: A switch port connected to an end host is stuck in a blocking state much longer than expected after a reboot. Which configuration change most directly speeds host access while still keeping loop protection elsewhere?

You are connected to R1. Configure IPv4 and IPv6 addressing on interfaces G0/0 and G0/1 so that R1 can reach R2's loopback0 (198.51.100.1/32) and R2 can reach R1's loopback0 (203.0.113.1/32). The current configuration has a wrong subnet mask on R1 G0/0 and a missing default gateway on R2, causing reachability failures. Additionally, configure IPv6 using EUI-64 on R1 G0/1 and static IPv6 on R2 G0/1 to enable IPv6 ping between the two routers. All devices are routers.

Match each network service to its primary function.

Drag and drop the following steps into the correct order to configure OSPFv3 for IPv6 on a Cisco router and verify basic neighbor relationships.

An engineer configures NAT overload on a router for inside users. Which resource is primarily used to let many internal hosts share one public IPv4 address?

A trunk link between two switches is operational, but one side shows a native VLAN mismatch warning. What is the main concern with that condition?

A router is configured with an access list intended to block Telnet from 192.168.10.0/24 to 10.1.1.10, but Telnet still works. What is the most likely reason?

Which four of the following are characteristics of Dynamic Trunking Protocol (DTP) and VLAN Trunking Protocol (VTP) used in Cisco switching? (Choose four.)

A network engineer is configuring HSRP on a pair of Cisco routers to provide first-hop redundancy for a subnet. The goal is to ensure that the router with the highest IPv4 address always becomes the active router, and that it automatically reclaims the active role after a failure. The engineer configures priority 100 on both routers. Which additional configuration is required to meet these objectives?

A host sends a packet larger than the outgoing interface MTU, and the IPv4 header has the Don't Fragment bit set. What will a router do with the packet?

Match each DHCPv4 message in the DORA process to its role.

Exhibit: R1 learns 192.168.50.0/24 from multiple sources. Which two statements are correct about the route that will be installed in the routing table?

Which three options accurately describe characteristics of OSPFv2 in a single area? (Choose three.)

A switch displays the following output: Switch# show interfaces trunk Port Mode Encapsulation Status Native vlan Gi1/0/24 on 802.1q trunking 99 Port Vlans allowed on trunk Gi1/0/24 10,20,30 Port Vlans active in management domain Gi1/0/24 10,20,30,40 Users in VLAN 40 cannot reach resources across this trunk. What is the most likely reason?

Exhibit: A router has both an OSPF-learned default route and a floating static default route. Which route is currently active?

A network administrator has configured a DHCP server on VLAN 100 with an IP address of 192.168.100.10/24. Clients on VLAN 200 (192.168.200.0/24) report that they cannot obtain an IP address via DHCP. The router is configured with a DHCP relay on the VLAN 200 interface. The administrator checks the router configuration and verifies that the relay is in place, but clients still fail to get an address. The switch that the router and clients connect to has DHCP snooping enabled. What is the most likely cause of this issue?

A multilayer switch has SVIs for VLAN 10 and VLAN 20, but hosts in those VLANs still cannot reach each other. The SVIs are up/up. Which additional condition is most likely required?

A junior network engineer configured a floating static route on Router R1 to provide backup connectivity to a remote network 10.10.10.0/24. The primary connection uses OSPF. However, after the primary link fails, hosts on R1 cannot reach the remote network. The OSPF adjacency is down, and the floating static route is not appearing in the routing table. Based on the exhibit, what is the most likely cause of the issue?

You are connected to R1, a multilayer switch acting as the root bridge for VLAN 10. The network has experienced a loop, and interface GigabitEthernet0/1 on R1 is currently in err-disabled state due to a BPDU guard violation. Configure the switch to recover automatically from err-disable state after 300 seconds, then verify that the interface comes back up.

Which TWO statements correctly describe the behavior of PortFast and BPDU Guard on a Cisco switch?

A company wants all routers and switches to use a common time source so log timestamps line up during incident review. Which two statements about NTP are correct?

You are connected to R1. Configure OSPFv3 for IPv6 on R1 and R2 so that the loopback0 interface on R1 (IPv6 address 2001:db8:1::1/64) can ping the loopback0 interface on R2 (IPv6 address 2001:db8:2::1/64). The routers are connected via their GigabitEthernet0/0 interfaces using IPv6 addresses 2001:db8:12::1/64 (R1) and 2001:db8:12::2/64 (R2). OSPFv3 process ID 100 must be used, and all interfaces must be in area 0.

A switch port should allow an IP phone and attached PC to operate correctly. The phone should place voice traffic in VLAN 200 while the PC remains in VLAN 20. Which configuration approach best supports that design?

A network engineer notices that a root port on a switch has transitioned to a loop-inconsistent state. The port was previously receiving BPDUs normally, but after a suspected unidirectional fiber cut, it no longer receives BPDUs. What is the most likely cause?

A router is configured for PAT overload. What does the inside global address represent for an internal PC?

You are connected to SW1 via the console. SW1 is a Layer 2 switch. Port GigabitEthernet0/1 connects to a PC in VLAN 10, and port GigabitEthernet0/2 connects to a server in VLAN 20. Both ports are currently in VLAN 1. Configure SW1 to assign GigabitEthernet0/1 to VLAN 10 and GigabitEthernet0/2 to VLAN 20, and verify the configuration.

Two routers are directly connected and running OSPF. Their IP addresses and hello timers match, but they still do not become neighbors. One side is configured for area 0 and the other for area 1 on the shared link. What is the most likely cause?

Match each programmability term to its most accurate description.

An administrator wants to permit SSH management access but block Telnet access to a device. Which statement best reflects that design goal?

Drag and drop the following steps into the correct order to describe how a router selects the best path and forwards a packet, using the routing table lookup process from destination IP to forwarding decision.

Which TWO statements accurately describe how AI and ML concepts are applied to network operations?

Match each HTTP method to the action it most commonly performs in a REST API.

Match each STP or switch protection feature to the problem it is mainly designed to prevent.

Which two statements accurately compare IPv4 private addresses and public addresses?

Which TWO statements accurately describe the responsibilities of the OSI model's Transport layer?

A network engineer is troubleshooting a connectivity issue between two hosts on different subnets. The sending host has constructed a packet with a destination IP address of 192.168.2.10. As the packet travels down the OSI model layers on the sending host, which Protocol Data Unit (PDU) name is assigned to the data at the Transport layer after TCP segments are created, and at which layer does the IP address get encapsulated?

You are connected to R1, a multilayer switch acting as the STP root bridge. Configure Root Guard on the designated port toward R2 (G0/1), Loop Guard on the uplink port G0/2, and BPDU Guard on PortFast-enabled access port G0/3. After configuration, a superior BPDU is received on G0/1, causing it to be blocked by Root Guard; later, an unauthorized BPDU on G0/3 triggers err-disable. Troubleshoot and verify the expected port states.

Drag and drop the following steps into the correct order to configure NTP with authentication on a Cisco router.

Drag and drop the following steps into the correct order to configure Root Guard on designated ports, Loop Guard on non-designated ports, and BPDU Guard on PortFast ports, and then recover a port that enters err-disabled due to BPDU Guard.

You are connected to R1. The network administrator has partially configured IPv4 and IPv6 on the interfaces. However, PC1 (connected to R1's G0/1) cannot reach PC2 (connected to R2's G0/1). Configure R1 and R2 so that PC1 can ping PC2. Fix any addressing errors. Use IPv4 subnet 192.0.2.0/30 for the link between R1 and R2, and 198.51.100.0/24 for the PC LANs. For IPv6, use 2001:db8:1::/64 on R1's G0/1 and 2001:db8:2::/64 on R2's G0/1, with R1's G0/1 using EUI-64 and R2's G0/1 using a static address 2001:db8:2::1/64.

Why is a northbound API valuable to orchestration systems in a controller-based architecture?

You are connected to R1 via the console. R1 is a router that needs to provide DHCP services for hosts on VLAN 10 (192.168.10.0/24) and VLAN 20 (192.168.20.0/24). The DHCP server is located on VLAN 10 at 192.168.10.100, but hosts on VLAN 20 cannot reach it directly. Configure R1 to forward DHCP broadcasts from VLAN 20 to the DHCP server.

Drag and drop the following steps into the correct order to isolate and resolve interface CRC errors, duplex mismatches, and flapping on a Cisco IOS-XE switch.

Which two statements about OSPF neighbor requirements on a shared Ethernet segment are correct? (Choose two.)

A router shows this output: R1#show ip ospf neighbor Neighbor ID Pri State Dead Time Address Interface 10.1.1.2 1 FULL/DR 00:00:34 192.168.12.2 GigabitEthernet0/0 10.1.1.3 1 2WAY/DROTHER 00:00:39 192.168.12.3 GigabitEthernet0/0 Which statement is correct?

Drag and drop the following steps into the correct order to configure Rapid PVST+ on SW1, make it the root bridge, and enable PortFast with BPDU Guard on all access ports.

A network technician is troubleshooting a link between two Cisco switches, SW1 and SW2, connected via a single-mode fiber optic cable. The interface on SW1 is up/up, but the interface on SW2 remains down/down. The technician has verified that the fiber cable is not damaged and that the SFP modules are correctly seated. Which configuration change should the technician make to resolve the issue?

Drag and drop the following steps into the correct order to configure Router R1 with OSPFv2 process 1 to form neighbor adjacencies only on GigabitEthernet0/1 while preventing OSPF hello packets on all other OSPF-enabled interfaces.

A subnet must support at least 62 usable hosts. Which prefix will create the smallest subnet that meets the requirement?

Match each IPv6 concept to its most accurate description.

Users receive addresses from the correct subnet and can reach destinations by IP address, but they cannot browse by hostname.

Which TWO statements accurately describe the encapsulation process and PDU naming across the OSI and TCP/IP models?

You are connected to SW1. Configure LACP EtherChannel between SW1 and SW2 using interfaces GigabitEthernet0/1 and GigabitEthernet0/2. Ensure the channel forms and passes traffic for VLAN 10. Troubleshoot and fix any issues preventing the channel from coming up.

An engineer successfully authenticates to a controller and receives a token. What is the usual reason for including that token in later API requests?

Drag and drop the syslog severity levels on the left to their corresponding names and meanings on the right.

Which TWO statements about IPv4 and IPv6 static routing are correct?

You are connected to the console of SW1. The network administrator reports that SW1 cannot discover neighbouring devices using CDP. SW1 is connected to R1 via GigabitEthernet0/1. CDP is globally enabled, but still no neighbours are shown.

Drag and drop the following steps into the correct order to plan, configure, and apply an extended ACL that blocks Telnet traffic from the 192.168.1.0/24 network to the 10.0.0.0/24 network, applied inbound on the interface facing the source.

A route to 10.10.10.0/24 is learned through two OSPF paths. Both have the same prefix length and the same administrative distance, but one path has a lower OSPF metric. Which path is preferred?

Which two statements accurately describe ARP in an IPv4 Ethernet network?

Drag and drop the following steps into the correct order to describe the general workflow for AI-assisted network configuration automation: receive intent, decompose into sub-tasks, call tools, validate output, and apply closed-loop remediation.

Drag and drop the following steps into the correct order to configure a secure Cisco switch, from enabling secure management access to implementing advanced dynamic ARP inspection.

Which three of the following are functions of the Dynamic Host Configuration Protocol (DHCP) in a network? (Choose three.)

Which TWO statements correctly describe the behavior of standard ACLs and their placement on interfaces?

A network administrator at a large enterprise notices that the network monitoring system frequently generates false positive alerts for unusual traffic patterns during normal business hours. The administrator wants to reduce these false positives while still detecting genuine security threats. Which AI/ML concept would best address this requirement?

Which THREE statements correctly describe the behavior of LACP modes in an EtherChannel configuration?

A network technician has configured static NAT with the command ip nat inside source static 192.168.1.10 203.0.113.10. The web server at 192.168.1.10 is accessible from the internet on TCP port 80 but not on TCP port 443. The ACL applied to the outside interface permits all IP traffic. What is the most appropriate next step to troubleshoot this issue?

You are connected to R1. The internal network 192.168.1.0/24 must be able to access the Internet via PAT (NAT overload) using the outside interface G0/1 with IP 203.0.113.1. Additionally, a web server at 192.168.1.100 must be reachable from the Internet via static NAT to the same outside interface. The current configuration has errors. Correct the NAT configuration so that inside hosts can browse the web and the server is reachable from outside.

A technician is troubleshooting a dual-stack network where an IPv6-only host cannot reach an IPv4 resource. The technician issues the show ipv6 interface brief command on the local router and notices the interface facing the host has a link-local address but no global unicast address. The technician then checks the running configuration and finds that the command ipv6 unicast-routing is missing. What is the most likely cause?

Which TWO statements are true regarding the configuration and placement of standard and extended ACLs on a router?

Which TWO statements correctly describe characteristics of SNMPv2c and SNMPv3 for network monitoring?

Users complain that log timestamps from several routers do not line up with one another. Which two actions are most appropriate?

Which command or tool would a network engineer use to verify if a client has a duplicate IP address conflict on the local subnet?

Which medium is the most common choice for a 10G uplink between wiring closets on different floors of the same building?

A router learns the same destination prefix from OSPF and EIGRP. The prefix length is identical, and both routes are valid. Which route is preferred by default?

A switch unexpectedly blocks a link toward the distribution layer. Gi1/0/24 shows a path cost of 4 while Gi1/0/23 shows a path cost of 19. Why did interface Gi1/0/24 become the root port instead of Gi1/0/23?

A technician is troubleshooting a network-wide broadcast storm that has caused severe performance issues. The technician notices that BPDU guard is globally enabled on the access layer switch, but no ports are in an err-disabled state. All access ports have PortFast enabled. What is the most likely cause?

Which TWO statements correctly describe the operation of the ip helper-address command in a DHCP relay agent configuration?

Which two statements accurately describe CAPWAP in a controller-based WLAN context?

A network administrator is configuring a new Windows workstation on a small office network that uses IPv4 addressing. The workstation must be able to communicate with devices on other subnets and resolve hostnames via a company DNS server at 10.10.10.5. The administrator has already set the IP address to 10.10.10.10 and the subnet mask to 255.255.255.0. Which additional parameter must be configured to meet both requirements?

Drag and drop the following steps into the correct order to configure gRPC streaming telemetry subscription on a Cisco IOS-XE device, from initial setup to data collection.

You are securing the spanning-tree topology on R1, the root bridge for VLAN 10. Intended configurations: Root Guard on GigabitEthernet1/0/3, Loop Guard on gigabit interfaces 1/0/1 and 1/0/2, and BPDU Guard on all PortFast-enabled interfaces. After initial configuration, a superior BPDU on G1/0/3 blocks the port (expected), and a host on G1/0/5 triggers BPDU Guard, causing err-disable (expected). However, you realize Loop Guard was not applied to the uplinks. Troubleshoot and apply the missing configuration.

Which THREE statements accurately describe the role of AI agents in closed-loop remediation workflows for network automation?

Which traffic type is typically most sensitive to delay and jitter and is commonly prioritized with QoS?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two links to SW2: G0/1 and G0/2. The administrator wants to combine these two links into an EtherChannel using LACP. Configure an EtherChannel on SW1 for these ports and verify.

Drag and drop the following steps into the correct order to configure AAA with a RADIUS server and 802.1X port authentication on an IOS-XE switch.

You are connected to SW1. An EtherChannel between SW1 and SW2 using LACP must be established on interfaces GigabitEthernet0/1 and GigabitEthernet0/2. Currently, the channel is not forming. Inspect the provided configuration and output, then apply the necessary commands on SW1 to resolve the issue and bring up the Port-Channel interface.

An ACL is intended to block Telnet from 10.1.1.0/24 to router VTY access while still allowing SSH from the same subnet. Which statement best explains why an extended ACL is appropriate here?

Refer to the exhibit. A network engineer is troubleshooting a connectivity issue on SW3. A host connected to the same segment as SW3's GigabitEthernet0/0 interface cannot reach any network resources. The engineer issues the show spanning-tree vlan 10 command and receives the output shown. Based on the output, what is the most likely cause?

Which two statements accurately describe OSPF passive interfaces?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with three redundant links to SW2: G0/1, G0/2, and G0/3. The network is experiencing loops, and STP is not configured. You need to enable STP and ensure that SW1 becomes the root bridge for VLAN 1. Configure STP on SW1 and set its priority to 4096 for VLAN 1.

At which OSI layer do routers make forwarding decisions based on logical addressing?

Which command correctly configures an IPv6 default route using next-hop address 2001:db8:1::1?

You are connected to SW1. Configure an LACP EtherChannel between SW1 and SW2 using interfaces GigabitEthernet0/1 and GigabitEthernet0/2. Set the channel-group mode to active on both switches. Verify that the port-channel interface is configured with VLAN 100 as an access port. Then, troubleshoot and fix the issue that prevents the EtherChannel from forming due to a mismatched speed on one of the member links. After correction, verify the EtherChannel is up with 'show etherchannel summary'.

A two-switch EtherChannel bundle is configured with LACP. One side uses active mode on both member links, while the other side uses passive mode on both member links. What is the result?

Match each security concept to its most accurate purpose.

You are connected to R1. Configure PAT (NAT overload) so that hosts on the 192.168.1.0/24 LAN can access the Internet via the outside interface GigabitEthernet 0/1 with IP 203.0.113.2/29. The current configuration has an incorrect inside/outside interface assignment and a missing overload keyword. Fix all issues.

A switch receives a unicast frame for a destination MAC address that is not yet in its MAC address table. What does the switch do?

A subnet uses the prefix /22. How many usable host addresses are available?

A network administrator is troubleshooting slow file transfers between two servers in different access-layer switches. The administrator runs the 'show interface' command on the uplink connecting the two switches and notices a high number of CRC errors on both ends, but a high number of late collisions on only one interface; the other interface reports no late collisions.

Which two statements accurately describe why least privilege and source restriction work well together for administrative access?

Drag and drop the following steps into the correct order to describe the data encapsulation process as it flows down the OSI model from the source host.

Which three of the following are correct statements about VLAN configuration and verification on a Cisco switch? (Choose three.)

Which two statements accurately describe IPv6 link-local addresses?

Why might voice traffic be placed in a priority queue on a WAN link?

Why does a passive interface in OSPF still matter even though it does not send hello packets?

Which TWO actions does DHCP snooping perform by default on a Cisco switch?

When spanning tree elects a root bridge, which value is considered first?

You are connected to SW1 via the console. SW1 is a Layer 2 switch. Ports G0/1 and G0/2 are connected to two PCs that should be in VLAN 10 (Sales). Port G0/3 is a trunk link to another switch. The PCs are currently unable to communicate because the ports are in VLAN 1. Configure the switch to place the ports in the correct VLAN and ensure the trunk is properly configured with 802.1Q encapsulation and native VLAN 99.

You are troubleshooting PAT and static NAT on R1. The inside network 192.168.10.0/24 must be translated to the public IP 203.0.113.1 (interface G0/1) using port address translation. Additionally, the server at 192.168.10.100 must be reachable from the outside via static NAT to 203.0.113.5. The current configuration is not working. Identify and correct the errors in the running config on R1.

Which two statements accurately describe DNS in everyday network use?

You are troubleshooting connectivity from R1 to the 172.16.20.0/24 network. The network engineer configured a floating static route on R1 as a backup for the OSPF-learned route, but after the primary OSPF route fails, the backup does not take over. Examine the current routing table and partial configuration on R1, then fix the issue so that when the OSPF neighbor goes down, R1 can still reach 172.16.20.0/24 via R3.

A technician is troubleshooting a network issue where hosts in VLAN 20 on SW1 cannot communicate with hosts in VLAN 20 on SW2. Both switches are connected by an Ethernet trunk link that is up/up and configured as a trunk. The VLAN databases on both switches include VLAN 20, and the spanning tree for VLAN 20 is in a forwarding state on all ports. Hosts within VLAN 20 on each switch can communicate with each other locally. What is the most likely cause?

Which field in an IPv4 packet is primarily used to prevent packets from looping forever in the network?

You are connected to R1 via console. R1 and R2 are connected via a serial link. OSPFv2 has been configured, but the adjacency is stuck in EXSTART state. You suspect a mismatched MTU. On R1, the interface MTU is currently set to 1400, while R2 uses the default MTU of 1500. You need to verify and fix the issue.

Which two statements accurately describe the relationship between a network address and a broadcast address in IPv4 subnetting?

Refer to the exhibit. A network engineer is troubleshooting a DHCP issue where DHCP clients on the LAN subnet are sending DHCPDISCOVER messages but the DHCP server does not receive them. The output of the show ip dhcp binding command on R1 is shown. What is the most likely cause of the problem?

Which two statements about RESTful APIs are correct? (Choose two.)

Drag and drop the switch port configuration commands on the left to the correct descriptions on the right.

Which TWO commands can a network technician use on a modern Linux host to verify the IP address configuration and test reachability to a remote server?

You are connected to R1 via the console. R1 and R2 are running OSPFv2 in area 0. R1's router ID is 1.1.1.1, and R2's router ID is 2.2.2.2. Both routers are connected via GigabitEthernet0/0 on the 192.168.12.0/30 subnet. You need to ensure that R1 does not send OSPF hello messages out of its Loopback0 interface, while still advertising the loopback network into OSPF.

Which command enables IPv6 routing on a Cisco router?

A network engineer is tasked with monitoring a large enterprise network that requires high-frequency, real-time data collection from thousands of routers and switches. The engineer needs a solution that minimizes CPU overhead on the network devices and supports push-based data delivery. Which technology should the engineer choose for this requirement?

A host sends traffic to a web server on another subnet. Which address is used as the destination MAC address in the first Ethernet frame sent by the host?

Which two statements accurately describe why logs and accounting records both matter in secure operations?

A user connects a small unmanaged switch to an access port, and the port immediately transitions to err-disabled. Which feature most likely caused this behavior?

Which TWO interface issues can be identified by analyzing the output of the 'show interfaces' command?

A network technician is troubleshooting an inter-VLAN routing issue on a multilayer switch. Hosts on VLAN 10 can reach the SVI for VLAN 10 (10.0.10.1) but cannot reach hosts on VLAN 20. The technician has verified that 'ip routing' is enabled and that the 'show ip route' command displays directly connected routes for both VLANs. No static routes are configured. What should the technician do next?

Refer to the exhibit. A network administrator is troubleshooting connectivity to devices in VLAN 10 on a Layer 3 switch. The administrator issues the show ip interface brief command on SW1 and sees the output displayed. What is the most likely reason that the VLAN 10 SVI is not functioning?

A wireless client can see two SSIDs from the same company: Corp and Guest. Which statement best explains what an SSID represents in this situation?

A routing table entry begins with the code C. What does that code indicate?

You are connected via the console to R1, a new Cisco ISR 4321 router. The network team requires that all routers be reachable via SSH for management. R1's management interface is GigabitEthernet0/0 with IP 192.168.1.1/24. You need to configure SSH on R1, including a hostname, domain name, RSA key pair of 1024 bits, local user 'admin' with secret 'cisco123', and enable SSH version 2. Additionally, configure the vty lines to accept only SSH connections and use local authentication.

Which feature helps prevent a rogue DHCP server from handing out addresses on a campus switch network?

Refer to the exhibit. A network administrator is troubleshooting connectivity issues. Hosts on the 192.168.10.0/24 network cannot reach servers on the 192.168.20.0/24 network, but they can successfully reach other networks, including the Internet. The administrator runs the show ip access-lists command on the router (output shown). What is the most likely cause?

A network administrator implements a set of spanning-tree enhancements to secure the switching infrastructure. Later, a help desk ticket reports that a user in a remote office cannot connect to any network resources. While investigating, the administrator notices that the switch port connecting the remote office switch to the distribution switch is in a 'root-inconsistent' state and is blocking traffic. Which protection feature, if misapplied, most likely caused this issue?

Two routers are directly connected over IPv6 and should form an OSPFv3 adjacency, but they do not. Link-local addressing is present on both interfaces. Which issue is most likely to prevent the adjacency?

Two switches are configured for LACP EtherChannel. One side is set to passive and the other side is also set to passive. What is the most likely outcome?

Why is a northbound API generally more useful to orchestration software than a human-readable CLI screen?

Drag and drop the following steps into the correct order to configure Root Guard on designated ports, Loop Guard on non-designated ports, and BPDU Guard on PortFast ports, and then recover a port that enters err-disabled state.

Match the data format to its most accurate characteristic.

Match each wireless term to its most accurate meaning.

Drag and drop the following steps into the correct order to configure AAA with a RADIUS server and 802.1X port authentication on a Cisco IOS-XE switch.

A switch interface connected to another switch must carry VLANs 10, 20, and 30 only. Which command best enforces that requirement on the trunk?

Which TWO statements accurately describe Network Address Translation (NAT) types?

What problem is HSRP designed to solve?

Based on the exhibit, which route will be used to reach 172.20.10.33?

Match each HTTP method to the most accurate action it commonly represents in REST-style APIs.

Why is disabling unused services on network devices considered a sound security practice?

You are connected to the console of R1, a Cisco router that is part of a larger network. The network operations team uses Ansible to manage configurations. You need to write an Ansible playbook that configures an interface description on R1. The playbook should use the ios_config module.

Which two statements accurately describe why SSH is preferred over Telnet for device administration?

Drag each automation or API concept from the left to its corresponding description on the right. Not all descriptions are used. Concepts: - Northbound API - Southbound API - JSON - HTTPS

Two OSPF routers connected on an Ethernet link remain in the INIT state. Which issue is the most likely cause?

You are connected to R1, a Cisco ISR 4331 router running IOS-XE. Your task is to enable SNMP v2c with community string 'public' (read-only) and 'private' (read-write), and configure SNMP v3 with a user 'admin' using SHA authentication (password 'Cisco123') and AES 128 encryption (password 'Cisco456'). Additionally, configure SNMP traps to be sent to a management server at 203.0.113.10 for both v2c and v3. Finally, enable NetFlow export to a collector at 203.0.113.20, using version 9. Verify your configuration using 'show snmp' and 'show ip cache flow'.

An EtherChannel should form using LACP between two switches. One side is configured for LACP active, and the other side is configured for LACP active. What is the expected result if the other link settings also match?

Drag and drop the following steps into the correct order to configure and recover from a BPDU Guard violation on a PortFast-enabled access port using Cisco IOS-XE CLI commands.

You are connected to R1. Configure static NAT for a public web server (198.51.100.10 to 192.168.1.10) and PAT for the 192.168.1.0/24 LAN to use interface GigabitEthernet0/1 with overload. The current configuration has misconfigured NAT that prevents both types from working. Identify and fix the issues so that internal hosts can access the internet and external hosts can reach the internal web server.

Exhibit: A user can ping 8.8.8.8 successfully but cannot browse to www.example.com by name. Which service is the most likely failing component?

Drag and drop the following steps into the correct order to configure a single-area OSPFv2 network on two Cisco routers (R1 and R2) and observe the neighbor state transitions from Down to Full.

Drag and drop the following commands into the correct order to configure OSPFv3 for IPv6 on a Cisco router.

You are connected to R1 via console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to an ISP, and GigabitEthernet0/1 (192.168.1.1/24) connects to the internal LAN. The network administrator needs to monitor R1's system messages. Configure R1 to send syslog messages with severity level 5 (notifications) and above to the syslog server at 10.0.0.2. Also, ensure that logging is enabled and that messages include the timestamp and source interface.

A wireless client can associate to the correct corporate SSID and authenticate successfully, but receives an address from the guest network instead of the employee network. Which troubleshooting area is strongest?

A switch interface connected to a Cisco IP phone with a PC behind it must carry voice and data correctly. Which two switchport commands are appropriate on that access port?

You are connected to R1. Configure SNMPv3 with authentication (SHA) and encryption (AES-128) for user 'monitor' in group 'AdminGroup', and also configure SNMPv2c read-only community string 'cisco123' to send traps to the management server at 192.0.2.100. Additionally, configure NetFlow on interface GigabitEthernet0/0 to export flow data to 198.51.100.50 using version 9. Verify your configuration using the appropriate show commands.

R1 and R2 are directly connected and running OSPF. The IP addressing is correct and both routers are in area 0, but they do not form an adjacency. What is the most likely cause?

A wireless client associates to an AP and successfully authenticates to the correct SSID, but it does not obtain an IP address. The WLC is running in local mode. What should the technician do next?

Which two statements accurately describe why APIs and human-oriented CLIs are both still useful in network operations?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to an ISP router at 10.0.0.2/30. The internal network has a web server at 192.168.1.10 and a mail server at 192.168.1.20. You need to configure NAT so that internal hosts can access the internet (PAT overload) and external users can reach the web server via public IP 203.0.113.10 and the mail server via public IP 203.0.113.11. The inside interface is GigabitEthernet0/1 (192.168.1.1/24) and the outside interface is GigabitEthernet0/0.

Why is route summarization often useful at distribution or area boundaries in larger networks?

A router learns 192.168.30.0/24 from OSPF and also has a static route to 192.168.30.0/24 with administrative distance 200. Which route is installed in the routing table while both are available?

A network administrator recently configured BPDU Guard on all access ports of a switch to protect against rogue switches. After the change, users in VLAN 10 report intermittent connectivity issues and frequent link flaps. The administrator checks the switch and notices that several ports are in an err-disabled state. What is the most likely cause of the problem?

A branch office needs four subnets from the 192.168.50.0/24 network, with each subnet supporting up to 50 hosts. Which prefix length should be used for each subnet?

Which TWO of the following are valid interpretations of errors seen in the output of the 'show interface' command?

You are connected to R1. The network administrator wants to permit only HTTPS traffic (TCP port 443) from the 192.0.2.0/24 network to the 203.0.113.0/24 network, while denying all other IP traffic. Currently, an ACL applied inbound on G0/1 is blocking all traffic, including HTTPS. Identify the issue and correct the ACL configuration so that only HTTPS traffic is permitted.

A router receives two routes to 10.50.0.0/16: one from OSPF and one static route with an administrative distance of 90. Which route is installed by default?

Which TWO statements about network automation tools are true?

A router has routes to 192.168.0.0/16 and 192.168.100.0/24. Which route is used for traffic to 192.168.100.77?

Match each basic IPv4 concept to its most accurate role.

Match each IPv6 address type or concept to its most accurate description.

Why is NTP especially valuable when a network uses centralized Syslog servers?

A wireless client joins the correct SSID and gets an address in the correct employee subnet, but cannot reach only one internal application while everything else works. Which troubleshooting area is the strongest first target?

You are connected to SW1 via console. SW1 is a Layer 2 switch with two ports (G0/1 and G0/2) connected to a host. The host should be able to send and receive traffic on VLAN 10 and VLAN 20. Configure the two ports as a trunk link to the host, but ensure that the trunk only carries VLANs 10 and 20, and set the native VLAN to VLAN 99.

You are troubleshooting a PC connected to switch SW1. The PC cannot access the internet. SW1 is connected to router R1 via port G0/1. R1 provides default gateway and DHCP services. Analyze the provided show output and fix the connectivity issue so that the PC can ping 8.8.8.8. === Show output from R1 === <pre> R1# show ip interface brief Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES manual administratively down down GigabitEthernet0/1 10.0.0.1 YES NVRAM up up </pre> === Show output from PC === <pre> C:\> ipconfig Ethernet adapter Ethernet0: Connection-specific DNS Suffix . : IPv4 Address. . . . . . . . . . : 169.254.123.45 Subnet Mask . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . : </pre> === Show output from SW1 === <pre> SW1# show vlan brief VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Gi0/1, Gi0/2, Gi0/3 </pre>

A routing table contains these entries for the same destination space: 10.1.0.0/16, 10.1.10.0/24, and 0.0.0.0/0. Which route is used for traffic to 10.1.10.44?

Which three options correctly describe how a router processes a packet destined for a remote network? (Choose three.)

Match each common network device or concept to its primary role.

You are connected to R1 via the console. R1 is a Cisco ISR 4321 router running IOS-XE. The network team has recently changed the routing protocol from EIGRP to OSPF, but some routes are missing from the routing table. You need to analyze the OSPF neighbor states and LSDB to identify the issue.

You are connected to R1 via console. The network has a primary link to the ISP via R2 and a backup link via R3. Configure IPv4 and IPv6 floating static default routes on R1 so that the primary path goes through R2 (AD 1) and the backup through R3 (AD 10). Additionally, configure a static route on R1 for the internal LAN 192.168.10.0/24 via R2 (AD 1). The current configuration includes a static default route ip route 0.0.0.0 0.0.0.0 10.0.0.3, which causes a recursive routing failure because 10.0.0.3 is not a valid next-hop address. Identify and fix the issue, then apply the floating static routes.

Drag and drop the following steps into the correct order to configure a router-on-a-stick topology for inter-VLAN routing between VLANs 10 and 20, using 802.1Q trunking with native VLAN 99 for management traffic.

A switch is configured with DHCP snooping and Dynamic ARP Inspection. Hosts suddenly lose connectivity after changing IP settings manually. Which explanation is strongest?

Two switches should form an EtherChannel using LACP. One side is configured active and the other passive. If the port settings otherwise match, what is the expected result?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two VLANs: VLAN 10 (Sales) and VLAN 20 (Engineering). Port G0/1 is connected to a sales PC, and port G0/2 is connected to an engineering PC. You need to ensure that each PC is in the correct VLAN. However, the sales PC is currently unable to ping the engineering PC because they are in different VLANs. You have a router R1 connected to SW1 via port G0/3. Configure inter-VLAN routing using Router-on-a-Stick on R1, and ensure SW1's port G0/3 is properly configured as a trunk.

An engineer is troubleshooting an OSPF adjacency between two directly connected routers, R1 and R2. R1 is configured with a passive-interface default under the OSPF process, and the interface connecting to R2 is not explicitly set to no passive-interface. The engineer runs a show ip ospf neighbor command on R1 and sees no neighbors. What is the most likely reason for the missing adjacency?

A branch router uses PAT for Internet access. Users can browse out, but the administrator wants a specific internal web server to be reachable from outside on a consistent public address. Which design fits that requirement best?

Drag and drop the following steps into the correct order to configure HSRP version 2 on an interface and ensure the router becomes the active router, then verify the HSRP state.

A host sends an IPv4 packet larger than the outgoing interface MTU, and the DF bit is not set. What will a router normally do?

Exhibit: A company wants to export traffic statistics from routers to a collector for visibility into top talkers and application usage. Which two statements are accurate?

Drag and drop the port configuration commands/technologies on the left to their corresponding descriptions on the right.

You are connected to SW1 via the console. SW1 is a multilayer switch with SVIs for VLANs 10 (192.168.10.1/24) and 20 (192.168.20.1/24). Hosts in VLAN 10 can ping their default gateway (192.168.10.1), but cannot ping hosts in VLAN 20. You suspect IP routing is not enabled or the SVIs are not up.

A host is configured with IP address 192.168.70.18/30. Which addresses belong to the same subnet block?

You are connected to R1 via the console. R1 is an NTP client that should synchronize its clock with NTP server 192.168.1.100. The timezone is UTC-5 (Eastern Standard Time). Configure NTP on R1 so that it becomes an NTP client. Additionally, configure the router to log NTP synchronization status messages to the console and buffer logging using the numeric severity level 6 (informational).

An automation script needs to send a bearer token when calling a controller REST API over HTTPS. Where is that token most commonly included?

You are connected to R1, a Cisco IOS-XE router that serves as the DNS resolver for the local network. The router can reach the DNS server at 198.51.100.53, but internal hosts cannot resolve the hostname 'fileserver.courseiva.com' (expected IP 203.0.113.10). Which configuration will resolve the issue?

An OSPF router learns a route with metric 20 and another OSPF route to the same destination with metric 30. The prefix length is the same. Which path is preferred?

A host address is 10.55.8.117/29. Which address is the network address of the subnet?

A REST API query returns this JSON snippet: { "interface": { "name": "GigabitEthernet1", "admin-status": "up", "oper-status": "down" } } What does this indicate?

Which THREE statements accurately describe the characteristics of NETCONF and RESTCONF for programmatic network configuration?

What data format is commonly used in REST API responses because it is lightweight and easy for applications to parse?

A network administrator has configured 802.1X port-based authentication on a Cisco IOS-XE switch for a new access port connected to a user workstation. The workstation is failing to gain network access. The switch port is in the 'authorized' state, but the workstation cannot ping the default gateway. The administrator checks the running configuration and the authentication session details. What is the most likely cause of the issue?

An engineer is allowed to log in to a router but cannot enter configuration mode. Which AAA function most directly explains that outcome?

Which TWO statements correctly describe the configuration and verification of OSPFv3 for IPv6?

In a network running STP, SW2 became the root bridge for VLAN 10. Both SW1 and SW2 have the same bridge priority. Why did SW2 become the root?

A router pair is directly connected, but they do not become OSPF neighbors. IP addressing and area assignment are correct. What is the most likely cause?

Drag and drop the following steps into the correct order to configure a Cisco IOS-XE router as a DHCP server for a VLAN 10 subnet and enable DHCP relay for a remote client on VLAN 20.

Which HTTP method is commonly used to retrieve information from a REST API without modifying the resource?

Drag and drop the following IOS-XE CLI commands into the correct order to configure AAA with a RADIUS server and then enable 802.1X port authentication on an interface.

You are connected to SW1 via the console. SW1 is a Layer 2 switch connected to a PC on port G0/1. The network administrator wants to secure the port by allowing only two MAC addresses and enabling sticky MAC learning. Additionally, if a violation occurs, the port should be put into error-disabled state. Configure port security on G0/1 with maximum MAC addresses of 2, sticky learning, and shutdown violation mode.

You are connected to R1 via console. R1 must reach the remote loopback 2001:db8:1::1/128 on R3 via R2 (2001:db8:0:2::2/64). Currently, IPv6 ping fails. Additionally, configure a floating static default route via R2 (198.51.100.2/30) with an appropriate AD so that it only becomes active if a dynamic default route (with default AD 1) is absent. Identify and fix the recursive routing failure, correct the next-hop, set the correct AD, and ensure the default route is present.

A support engineer is explaining why a host uses ARP before sending a frame on an Ethernet LAN. Which two statements are correct?

Which three of the following are characteristics of Layer 2 Ethernet switches that improve network performance? (Choose three.)

A network engineer has enabled DHCP snooping on a Catalyst switch to prevent rogue DHCP servers. All access ports in VLAN 10 are untrusted. A router attached to a trunk port on the switch acts as the default gateway for VLAN 10 and is configured with the ip helper-address 10.1.2.5, which points to a remote DHCP server. After enabling DHCP snooping, hosts in VLAN 10 cannot obtain IP addresses; packet captures show DHCPDISCOVER messages are sent, but no DHCPOFFER is received. What is the most likely cause?

A user reports that their desk port stopped working immediately after they connected a small switch. The interface shows err-disabled, and the log mentions BPDU Guard. What most likely happened?

Which three options best describe how machine learning models are trained for network anomaly detection? (Choose three.)

Which protocol is most directly responsible for keeping device clocks synchronized across a network?

Drag and drop the following phases into the correct order to configure gRPC streaming telemetry subscription setup and then the NetFlow data path sequence.

You are connected to R1 via console. PC1 is connected to R1's GigabitEthernet0/1 interface and is configured with a static IP address. PC1 cannot reach the internet (203.0.113.1). Identify and resolve the connectivity issue. Configure R1 to restore full connectivity for PC1.

An EtherChannel uses LACP. One side is configured correctly, but the peer side has a different switchport mode on one of the member links. What is the most likely result?

You are troubleshooting a PC (PC-A) connected to switch SW1, which is connected to router R1. PC-A has an APIPA address (169.254.23.45) and cannot reach the internet (203.0.113.1). You confirm that R1 has a correctly configured DHCP pool for the 192.168.10.0/24 subnet, but the DHCP service is not enabled. The network uses VLAN 10 with subnet 192.168.10.0/24. Verify and correct the configuration on PC-A, SW1, and R1 to restore full connectivity.

You are connected to R1. Configure OSPFv3 for IPv6 so that R1 and R2 can exchange IPv6 routes over their directly connected link. Enable IPv6 routing, assign OSPFv3 process and area on the interface, and verify that the neighbor adjacency forms and routes appear in the IPv6 routing table.

A client connects to an employee WLAN using 802.1X authentication. The authentication process completes successfully, but the client fails to obtain an IP address via DHCP. What is the most likely cause?

You are connected to R1 via the console. R1 and R2 are connected via a fiber link using SFPs. The link is not coming up. Configure the correct SFP type on R1's interface GigabitEthernet0/0 to support the required 2 km distance, and fix any auto-negotiation or speed/duplex misconfiguration so that the link becomes operational.

A company wants to connect two sites across an IP network by creating a logical tunnel between the edge routers. Which technology is most directly associated with that requirement?

You are connected to R1 via console. R1 has two interfaces: GigabitEthernet0/0 (10.0.0.1/30, connected to ISP) and GigabitEthernet0/1 (192.168.1.1/24, connected to internal LAN). The LAN hosts (192.168.1.0/24) need to access the internet. Configure dynamic NAT with PAT (overload) on R1 using a NAT pool so that internal hosts share the public IP 10.0.0.1 when accessing the internet. Assume the ISP router is already configured and reachable.

You are connected to R1, a multilayer switch acting as the STP root for VLAN 10. Configure Root Guard on the designated port facing a downstream switch to prevent a rogue switch from becoming root. Also, enable Loop Guard on the uplink port to prevent STP loops, and configure BPDU Guard on a PortFast-enabled access port. Ensure that if a superior BPDU is received on the Root Guard port, it is blocked, and if a BPDU is received on the BPDU Guard port, it goes err-disabled.

You are connected to a multilayer switch MLS1 via the console. Configure MLS1 so that IP phones connected to interface GigabitEthernet0/1 receive power via PoE, use VLAN 10 for data traffic, and use VLAN 20 for voice traffic, while the access port for an AP on GigabitEthernet0/2 should be placed in VLAN 30 and have PoE disabled. Verify your configuration using appropriate show commands.

Which TWO statements correctly describe the behavior of PAT (Port Address Translation) as configured on a Cisco router?

You are connected to R1, a branch router. Configure an extended ACL named BRANCH_IN that permits only HTTP (TCP port 80) traffic from the internal network 192.168.1.0/24 to the web server at 203.0.113.10, and permits ICMP echo-reply from any source to any destination. Apply the ACL inbound on the interface facing the internal network. Then verify that only the specified traffic is allowed.

Which two statements about YANG are correct?

A host address is 192.168.90.33/28. Which address is the last usable host in the subnet?

A network engineer adds a loopback interface Lo0 with IP address 172.16.0.1/32 to router R1. After restarting the OSPF process, the OSPF router-ID changes from 10.1.1.1 to 172.16.0.1, and the neighbor relationship with R2 resets. What should the technician do next to prevent this disruption the next time a loopback is added?

An OSPF-enabled router R1 fails to advertise the 192.168.50.0/24 network to neighbor R2, even though the neighbor relationship is up. Which misconfiguration on R1 would cause this?

A host with address 10.0.0.130/25 needs to identify its subnet. Which subnet is correct?

You are connected to the console of R1. The network administrator reports that R1 cannot discover neighboring devices via CDP. R1 is connected to SW1 via GigabitEthernet0/0. You suspect CDP is disabled globally or on the interface. Your task is to enable CDP and verify neighbor discovery.

A network technician is troubleshooting a DHCP relay issue. The router at the branch office is supposed to forward DHCP requests from local clients to a central DHCP server. Clients connected to Gi0/1 are not receiving IP addresses. The technician verifies that the DHCP server is reachable from the router, that no ACLs are blocking DHCP traffic, and that the DHCP scope on the server has available leases. Upon checking the running configuration, the technician notices that the ip helper-address command is applied to interface Gi0/0 (the WAN link toward the server) instead of Gi0/1. What should the technician do next?

A network engineer has implemented DHCP snooping on a Cisco switch to prevent unauthorized DHCP servers. The switch's VLAN 100 SVI is configured with ip helper-address to relay DHCP requests to a legitimate server in VLAN 200. Clients in VLAN 100 cannot obtain IP leases, even though the DHCP server is reachable from the switch and has available addresses.

Which two statements about ARP on an IPv4 Ethernet network are correct? (Choose two.)

You are connected to R1, a Cisco router running IOS-XE. Configure SNMP v2c with a read-only community string 'publicRW' (note: the string is intentionally misnamed for the task), and SNMP v3 with user 'admin' using MD5 authentication (password 'cisco123') and DES encryption (password 'cisco456'). Ensure SNMP traps for linkUp/linkDown are sent to the management server at 192.0.2.100. Additionally, configure NetFlow export to send version 9 flow records to 192.0.2.200 on UDP port 2055, and ensure that only inbound traffic on GigabitEthernet0/0 is monitored. Finally, verify your configuration using 'show snmp' and 'show ip cache flow'.

Which command places a switch interface into trunking mode directly instead of relying on negotiation?

Drag and drop the following steps into the correct order to retrieve the operational status of interface GigabitEthernet0/0 using NETCONF and the ietf-interfaces YANG model.

A host cannot communicate with its default gateway. The technician uses the show arp command on the host and sees that the ARP entry for the gateway IP is incomplete. The technician has already verified that the Ethernet cable is securely connected and the switch port is active. What should the technician do next?

Which HTTP method is normally used by a REST API client to retrieve data from a resource without changing it?

Exhibit: A router has the following routes in its routing table: - OSPF: 10.1.1.0/24 - Static: 10.1.1.128/25 - Default: 0.0.0.0/0 A packet is destined for 10.1.1.130. Which route does the router use?

A switch stack is running PVST+. Users on VLAN 40 lose connectivity for roughly 30 seconds every time the uplink on SW2 flaps. Based on the exhibit, which change would most directly improve convergence for this VLAN?

Which Cisco IOS command configures a default static route pointing to next hop 203.0.113.1?

A network engineer receives a call that users in VLAN 10 on Switch B cannot ping the default gateway, which is a router on a stick connected to Switch A. The engineer checks the Spanning Tree Protocol state on the interface connecting Switch A to Switch B (GigabitEthernet0/1) and finds it is in a root-inconsistent state. Which command output best explains the cause of the issue?

You are connected to SW1 via console. SW1 is a Layer 2 switch. Port G0/1 connects to a PC that should be allowed only one MAC address. Currently, the port is configured with default settings. You need to enable port security on G0/1, set the maximum MAC addresses to 1, configure the port to shut down if a violation occurs, and ensure that the first learned MAC address is sticky (i.e., saved to the running config).

Which IPv6 address type is automatically created on an interface and used for communication on the local link only?

A network administrator is troubleshooting an IPv6 connectivity issue on a newly deployed router. The router's G0/0/0 interface is configured with an IPv6 address using EUI-64, but hosts on that subnet cannot reach the router's link-local address. The administrator runs 'show ipv6 interface g0/0/0' and sees that the interface is up/up but the IPv6 address is not in the expected format. What is the most likely cause of the problem?

A route to 10.10.20.0/24 disappears when an OSPF adjacency fails. Which design would most directly provide an automatic backup without changing the primary OSPF path during normal operation?

Match each API workflow concept to the description that best fits it.

You are connected to R1. The inside network 192.168.1.0/24 must be translated to the outside interface IP (198.51.100.1) using PAT (NAT overload). Additionally, a static NAT entry must map host 192.168.1.10 to 203.0.113.10. The current configuration is incomplete and contains errors. Correct the configuration so that both translations work properly.

Why is NTP especially valuable when a company uses a centralized Syslog server?

You are connected to R1 via console. R1 is a router that connects two internal subnets (192.168.1.0/24 and 192.168.2.0/24) to the internet via a serial link to ISP. Currently, no ACL is applied. Your task is to configure an extended named ACL on R1 that permits only HTTP (TCP/80) and HTTPS (TCP/443) traffic from the 192.168.1.0/24 subnet to the internet, and denies all other traffic from that subnet. Traffic from 192.168.2.0/24 must be permitted without restriction. Apply the ACL inbound on the interface facing the internal subnets. Additionally, verify that the implicit deny is not blocking necessary traffic by ensuring that the ACL correctly handles the traffic.

A network administrator is troubleshooting connectivity loss in a switched network. All switches run Rapid PVST+. A host connected to an access port on SwitchC can no longer reach the default gateway. The access port is configured with PortFast and BPDU Guard. The administrator checks the interface status and finds it in an err-disabled state. What is the most likely cause of this issue?

Exhibit: R1 has a static default route to 192.0.2.2 and also learns a default route from OSPF. Which default route is installed in the routing table?

You are connected to R1. Configure HSRP so that R1 becomes the active router for VLAN 10, with a virtual IP of 192.168.10.1. Ensure that R1 preempts if it comes back online after a failure. Also, configure R1 to decrement its HSRP priority by 20 if its GigabitEthernet0/1 interface goes down. The current configuration shows both routers as active — identify and fix the issues.

Drag and drop the following steps into the correct order to create VLANs, assign access ports, configure 802.1Q trunks, set the native VLAN, and verify with 'show vlan brief' and 'show interfaces trunk'.

A switch displays the following output: Interface Status VLAN Gi1/0/5 connected 20 Gi1/0/6 notconnect 1 Gi1/0/24 trunk trunk Which interface is operating as an access port in VLAN 20?

A network engineer successfully logs in to a router, but cannot enter configuration mode because the command is rejected by policy. Which AAA function is controlling this behavior?

A network engineer notices that users on VLAN 100 are experiencing intermittent connectivity to the server farm. The switch connecting these users shows no errors on the uplink interface, but the server farm switch reports a high number of input errors on its connected interface. The engineer runs 'show controllers' on the server farm switch. What is the most likely cause of the issue?

Which OSPF component is used to identify routers uniquely inside an OSPF domain?

Drag and drop the following troubleshooting steps into the correct order to diagnose a client connectivity issue using the OSI bottom-up method.

Drag and drop the following steps into the correct order to configure Rapid PVST+ with a designated root bridge, PortFast, and BPDU Guard on access ports.

A trunk link between two switches is up, but hosts in VLAN 30 on opposite switches cannot communicate. VLAN 10 works across the same trunk. Which two causes are the most likely?

Drag and drop the items on the left to match the descriptions on the right.

Drag and drop the following steps into the correct order to replace a faulty fiber optic SFP module and verify the interface on a Cisco IOS-XE switch. Assume the fiber cable is already disconnected from the SFP module.

A switch port is configured with `switchport voice vlan 150` and `switchport access vlan 20`. Which statement best explains the design purpose?

Inside hosts can reach the internet only one at a time. What is the most likely NAT issue?

Two static routes exist for the 203.0.113.0/24 network: one pointing to ISP-A with an administrative distance of 10, and another pointing to ISP-B with an administrative distance of 5. Packets for that subnet are leaving through ISP-B. What explains this behavior?

Match each access-control term to its most accurate meaning.

Drag and drop the following steps into the correct order to configure a Cisco IOS-XE router as a DHCP server for a local subnet and enable a DHCP relay agent on a different interface to forward client requests to that server.

You are connected to SW1. The network has experienced a spanning-tree topology change, and the new root bridge is not the intended core switch. Configure SW1 with a root primary priority, enable PortFast and BPDU Guard on interface GigabitEthernet0/3 (an edge port connected to a server), and verify that a specific port in the topology is blocking. Then, after a BPDU violation occurs on G0/3, recover the interface from err-disable state without reloading the switch.

Match each Layer 2 protection feature to its most accurate purpose.

Which two statements correctly describe syslog severity levels?

Refer to the exhibit. A network administrator notices that newly connected devices on the 192.168.1.0/24 subnet are failing to obtain IP addresses via DHCP and are instead assigning themselves APIPA addresses. The administrator issues the show ip dhcp pool command on the router and receives the output shown. What is the most likely cause of this issue?

In a controller-based network architecture, what is a southbound API typically used for?

Based on the exhibit, why is traffic to host 198.51.100.70 using the OSPF route instead of the static route?

A router is configured as follows: interface g0/1 ip address 172.16.1.1 255.255.255.0 ip helper-address 10.20.20.10 Hosts on 172.16.1.0/24 are not receiving addresses from the DHCP server at 10.20.20.10. The server is reachable by ping from the router. What is the purpose of the ip helper-address command in this scenario?

Refer to the exhibit. A network engineer is troubleshooting an issue where syslog messages at severity 6 (informational) and severity 7 (debugging) are not being sent to the syslog server at 192.168.100.50, even though the device appears to generate these messages locally. Based on the exhibit, what is the most likely cause?

Match each security control or idea to its most accurate purpose.

Exhibit: An administrator wants inside hosts in 192.168.10.0/24 to reach the internet using one public IP address on the edge router. Which feature is being used?

You are connected to R1, a branch router connected to a central NTP server at 203.0.113.10 and a syslog server at 198.51.100.20. Configure R1 as an NTP client using its Loopback0 interface (192.168.1.1/32) as the source, and ensure syslog messages of severity 'informational' and above are sent to the syslog server. Currently, R1 shows 'Clock is unsynchronized, stratum 16'. Identify and fix the NTP issue, then apply the syslog configuration.

Which of the following sequences correctly orders the steps to plan, configure, and apply an extended ACL that permits HTTP traffic from the 192.168.1.0/24 subnet to the server at 10.0.0.1, and deny all other IP traffic, applied inbound on interface GigabitEthernet0/1?

A network engineer configures an EtherChannel between two switches. Switch A's interface is set with channel-group 1 mode active, while Switch B's identical interface is set with channel-group 1 mode auto. When verifying with show etherchannel summary, the engineer observes that the port-channel interface is down and the physical interfaces are not bundled. What is the most likely cause of the problem?

What is the best explanation for why a router chooses the OSPF route to 10.50.0.0/16 instead of the RIP route?

You are connected to R1 via the console. R1 and R2 are directly connected via their GigabitEthernet0/0 interfaces. The link between them is down. Your task is to diagnose and fix the issue: R1's interface is configured for 100 Mbps full-duplex, but R2 is using auto-negotiation. Additionally, the link requires a Gigabit Ethernet connection over a distance of 5 km. Configure R1's interface to match R2's settings (auto-negotiation) and then select and install the correct SFP module to support the 5 km distance requirement.

Why is RIP rarely chosen for large modern enterprise networks?

You are connected to SW1 via console. SW1 is a Layer 2 switch connected to SW2 via three links (G0/1, G0/2, G0/3) that should form an EtherChannel using LACP. Currently, the interfaces are configured as access ports in VLAN 1. Configure the three interfaces as a LACP EtherChannel trunk that carries VLANs 1-100, and ensure the port-channel interface is operational.

Which DHCP message does the client send to formally accept an offered address?

You are connected to WLC-1 via the management interface (192.168.1.100/24). The wireless network 'CustomerNet' uses WPA3-Personal, but clients are failing to associate. The SSID is hidden and the correct VLAN is 30. Configure the WLAN and SSID parameters to allow successful client associations and verify the configuration.

Why is a default route often called a route of last resort?

Based on the exhibit, which command is the best next step to verify whether the floating static route becomes active after the primary route is lost?

Drag and drop the following steps into the correct order for an agentic AI system to remediate a network performance issue using Cisco IOS-XE CLI commands.

You are connected to R1. Configure DHCP services so that hosts on VLAN 10 (192.168.10.0/24) can obtain IP addresses from R1. Additionally, configure the switch SW1 to prevent rogue DHCP server attacks on that VLAN. The current configuration has a misconfigured helper-address and an excluded-address range that is too broad.

Drag and drop the following steps into the correct order to explicitly configure OSPFv3 for IPv6 on a Cisco IOS-XE router, assuming no OSPFv3 routing process exists beforehand.

You are managing a Cisco WLC (WLC-1) with IP 10.10.10.10. A wireless client reports it can see the SSID 'CorpNet' but fails to associate. The SSID is configured for WPA3, but the client only supports WPA2. Additionally, the WLAN is mapped to VLAN 100, but the AP is on VLAN 10, causing a mismatch. Your task: reconfigure the WLAN to use WPA2-PSK with AES encryption, correct the VLAN assignment to 10, and ensure the SSID is hidden. Also, verify that management access via the WLC web UI is restricted to the 192.168.1.0/24 subnet.

A network engineer notices that hosts in the 192.168.2.0/24 network connected to router R1's GigabitEthernet0/1 interface cannot reach the Internet. R1 has a standard ACL 10 configured as 'access-list 10 permit 192.168.1.0 0.0.0.255' and applied inbound on interface GigabitEthernet0/0, which connects to the 192.168.1.0/24 LAN. What is the most likely cause?

You are connected to R1. The link between R1's GigabitEthernet0/0 and R2's GigabitEthernet0/0 should operate at 1 Gbps full duplex, but the interface is showing errors and only negotiating at 100 Mbps half duplex. Diagnose and fix the fault, then verify the link is stable at the correct speed and duplex.

You are verifying OSPF operation on router R1. After confirming that OSPF is configured on the correct interfaces, which command should you use next to directly check whether R1 has established a neighbor adjacency with another OSPF router?

Exhibit: R1 can ping 10.1.23.2 but cannot ping 192.168.3.10 behind R3. The routing table on R1 lacks 192.168.3.0/24. What is the best next check?

Which two statements accurately describe longest-prefix match?

Match each automation term to the best description.

Which THREE of the following best describe how agentic AI is used in network automation, specifically regarding AI agents, tool-calling, and closed-loop remediation workflows?

A network technician is troubleshooting a router-on-a-stick configuration. R1 has sub-interface G0/0.10 with encapsulation dot1q 10 and IP 192.168.10.1/24, and sub-interface G0/0.20 with encapsulation dot1q 20 and IP 192.168.20.1/24. Hosts in VLAN 10 cannot reach hosts in VLAN 20. The physical interface G0/0 is up and no shutdown. Both sub-interfaces show up/up. What should the technician do next?

You are connected to R1. The network currently uses a static default route pointing to ISP1 (198.51.100.1) via GigabitEthernet0/0. However, the backup link to ISP2 (203.0.113.1) via Serial0/0/0 has a floating static default route with an administrative distance of 130. The backup route is not taking over when the primary link fails. Configure the floating static route correctly so that it becomes active when the primary route is lost, and verify that the routing table shows the backup default route with the appropriate next-hop.

Based on the exhibit, what is the most likely reason the PPP link is down?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to the ISP. GigabitEthernet0/1 (192.168.1.1/24) connects to the internal LAN. The security policy requires that only SSH traffic (TCP port 22) from the internal network (192.168.1.0/24) be permitted to reach the router itself, and all other inbound traffic to the router from internal hosts should be blocked. Additionally, the router must be hardened for SSH access: generate RSA keys of 2048 bits, set SSH version 2, enable SSH on vty lines, and disable Telnet. Currently, there is no security configuration. Configure R1 to meet these requirements.

An engineer is deploying a new Cisco Catalyst 9300 switch in a campus wiring closet. The uplink to the distribution switch uses a 1000BASE-LX SFP module. After connecting the fiber, the interface shows 'up/up' but the engineer notices that the 'input errors' counter is incrementing rapidly, with many CRC errors, runts, and giants being reported. What is the most likely cause of these input errors?

Which switch security feature uses DHCP snooping bindings to validate ARP packets and help stop ARP spoofing?

A network technician is troubleshooting a connectivity issue between two hosts on different subnets. During the analysis, the technician captures packets and observes that the data link layer frames are being stripped and rebuilt at each router hop. Which layer of the OSI model is responsible for encapsulating the original data into segments before transmission from the source host?

What metric does RIP use to choose the best path?

An IP phone connected to switch port Gi0/4 is working and receiving calls, but the PC connected to the phone's data port cannot obtain an IP address. The technician confirms that interface Gi0/4 has switchport mode access and shows switchport access vlan 10 and switchport voice vlan 100. What should the technician do next?

You are connected via the console to SW1, a Cisco Catalyst 2960 switch. The network administrator reports that users in VLAN 10 (Sales) cannot ping the default gateway 192.168.10.1, which is on R1's GigabitEthernet0/1 interface. SW1's interface GigabitEthernet0/1 connects to R1 and is configured as an access port in VLAN 10. R1's interface GigabitEthernet0/1 is configured with IP 192.168.10.1/24 and no shutdown. However, the link between them is up but the line protocol is down on both sides.

Match each operations or assurance technology to its most accurate purpose.

Which OSI layer is responsible for end-to-end segmentation, port numbers, and reliability functions such as acknowledgments?

A network engineer notices that an NMS at 10.1.1.200 cannot poll a router that has SNMPv2c configured with community string 'public'. What is causing this issue?

Which two statements accurately describe JSON arrays?

A network team wants centralized logging and also wants log timestamps from different devices to line up accurately. Which combination best supports that goal?

You are connected to R1. The network has R1, R2, and a multilayer switch MLS1. Configure IPv4 and IPv6 addressing on R1's interfaces so that R1 can ping both R2 (198.51.100.2) and MLS1 (203.0.113.2) via IPv4. Additionally, configure IPv6 on G0/1 using EUI-64 with prefix 2001:db8:1::/64 and verify that R1 can ping the IPv6 address of MLS1 (2001:db8:1::2). The current configuration has incorrect subnet masks and missing IPv6 settings, causing reachability failures.

R1 and R2 are directly connected and running OSPF. They can ping each other, the area matches, and the timers match, but they still do not become neighbors. What is the most likely cause?

A switchport on one side of a link is configured as a trunk, but the peer side is configured as an access port. The physical link is up, but VLAN traffic behaves unexpectedly. What is the most likely cause?

A switch port and a host NIC have a duplex mismatch. Which symptom is most likely?

Which TWO interface errors are most likely caused by a mismatch in duplex settings between two connected switches?

A network administrator configures OSPF on two routers, R1 and R2, connected via their Serial0/0/0 interfaces (IP addresses 10.1.1.1/30 and 10.1.1.2/30). They verify that both routers use the same OSPF process ID and area 0, but R1's 'show ip ospf neighbor' shows no adjacencies. Given the partial exhibit from R1, what is the most likely cause of the adjacency failure and its correct solution?

Which TWO statements correctly describe the configuration and effect of Root Guard and BPDU Guard on a Cisco switch?

Which TWO statements accurately describe OSPFv3 configuration and verification for IPv6?

Drag and drop the following steps into the correct order to configure IPv4 and IPv6 static routes, a default route, and a floating static route with a higher administrative distance, then verify with show ip route and show ipv6 route.

You are connected to SW1. A LACP EtherChannel between SW1 and SW2 has already been configured using interfaces GigabitEthernet0/1 and GigabitEthernet0/2 with channel-group 1 mode active on both sides and assigned to VLAN 100. However, the channel is not forming because of a speed/duplex mismatch. The correct interface settings for this network are speed 1000 and duplex full. Interface GigabitEthernet0/1 is already configured with these settings. Only interface GigabitEthernet0/2 needs to be corrected. Identify the configuration change needed to resolve the mismatch and verify the EtherChannel is up with 'show etherchannel summary'.

You are connected to a multilayer switch SW1 via console. SW1 has an IP phone and an access point connected to interfaces GigabitEthernet0/1 and GigabitEthernet0/2 respectively. Configure the access ports so that the IP phone receives a voice VLAN (VLAN 110) and PoE priority critical, and the access point receives PoE priority high. Verify your configuration using show interfaces switchport and show power inline.

Refer to the exhibit. A network engineer expects SW1 to be the root bridge for VLAN 1, but the show spanning-tree vlan 1 output on SW2 shows that SW2 is the root. What is the most likely cause of this issue?

You are connected to R1, a Cisco IOS-XE router acting as the network's DNS client. The network uses a local DNS server at 203.0.113.10 for internal name resolution. Users report that the hostname 'fileserver.courseiva.local' cannot be resolved, while other names work fine. Diagnose and fix the DNS resolution failure so that 'fileserver.courseiva.local' resolves correctly.

Which two statements accurately describe a controller-based WLAN compared with a set of independently managed APs?

Which two practices most improve safety when automating network changes? (Choose two.)

You are connected to SW1. Two switches, SW1 and SW2, are connected via four GigabitEthernet links. Configure LACP EtherChannel between them using interfaces GigabitEthernet0/1 through GigabitEthernet0/4 on SW1. Set the channel-group mode to active on SW1. The port-channel interface must be configured as a trunk, allowing VLANs 10, 20, 30. However, the EtherChannel is not forming. The current configuration is shown below. Identify and fix the issue, then verify the EtherChannel is operational.

An ACL entry reads: access-list 25 permit 192.168.8.0 0.0.0.15 Which address range does this statement match?

A router learns the same prefix from both OSPF and EIGRP. Which route is installed by default?

R1 and R2 are connected via a GigabitEthernet link in the same IPv4 subnet, and both routers have OSPF configured in the same area. However, R1 is not learning any OSPF routes from R2. What is the most likely cause?

Drag and drop the following steps into the correct order to configure a Cisco switch with an IPv4 management address 192.168.1.10/24, an IPv6 address 2001:db8:1::1/64, and a default gateway 192.168.1.1.

Which TWO statements correctly describe how a router selects the best path for a destination network when multiple routing table entries exist?

A user on VLAN 10 reports that they cannot ping the default gateway at 192.168.10.1 from their PC with IP 192.168.10.50/24. The switch interface connecting to the PC is up/up, and the PC shows a valid IP configuration. What is the most likely cause of this connectivity failure?

A network engineer is troubleshooting a connectivity issue between two hosts on different VLANs. The engineer captures traffic on an IOS-XE router's GigabitEthernet0/1 interface using embedded packet capture (EPC). The output shows ARP requests from Host A (192.168.1.10) but no ARP replies from Host B (192.168.2.20). What is the most likely cause of this issue?

Why is centralized logging especially useful when combined with NTP?

A router learns 203.0.113.0/24 through OSPF and 203.0.113.0/25 through a static route. Which route is used for traffic destined to 203.0.113.10?

A switch port connected to a user PC should be placed in VLAN 20 and must not negotiate trunking. Which configuration is the most appropriate?

A host is configured with IP address 192.168.50.94/27. Which subnet contains that host?

You are connected to R1, a Cisco ISR 4321 running IOS-XE. Configure SNMPv2c with a read-only community string 'public' and SNMPv3 with user 'admin' using SHA authentication and AES encryption. Ensure SNMP traps are sent to the management server at 203.0.113.10. Additionally, configure NetFlow export to destination 203.0.113.20 on UDP port 2055 using version 9. Verify your configuration with appropriate show commands. The current running-config is incomplete; you must add the missing commands.

Refer to the exhibit. A network engineer is troubleshooting connectivity to server 10.10.10.130. The routing table contains both a static route and an OSPF route for overlapping prefixes. The engineer examines the specific routing entry for 10.10.10.130. Based on the output, why does the router choose the route via 10.1.1.2 instead of the OSPF route via 10.2.2.2 (for 10.10.10.0/24)?

Which three of the following are characteristics of DHCP snooping on a Cisco switch? (Choose three.)

Which TWO statements accurately describe characteristics of copper and fiber optic cabling used in modern Ethernet networks?

You are connected to R1. The network has two routers: R1 (192.168.1.0/24 LAN) and R2 (Internet gateway). R1's inside LAN (192.168.1.0/24) must be translated to the public IP 203.0.113.1 using PAT (NAT overload) for Internet access. Additionally, the server at 192.168.1.100 must be reachable from the Internet via static NAT to 203.0.113.5. The current configuration is broken. Identify and fix the issues so that both PAT and static NAT work correctly.

Which TWO DNS record types are most commonly used together to verify both forward and reverse DNS mappings for an IPv6 address?

Which of the following shows the correct order of steps to troubleshoot a suspected duplex mismatch and CRC errors on a Cisco IOS-XE interface?

Select the correct sequence of steps to retrieve a specific interface's configuration via RESTCONF and apply a change to the interface description.

An IPv6 host successfully reaches neighbors on its local segment, but it cannot reach remote IPv6 destinations. The host has a global unicast address and a correct prefix length. Which missing item is the strongest suspect?

You are connected to the Cisco WLC (WLC-1) via its management IP 192.168.1.10. The wireless network 'CorpNet' is configured but clients cannot associate. Troubleshoot and resolve the issue: clients report 'Association failed' and the SSID is not visible in site surveys. Ensure that after your fix, the SSID is broadcast, WPA3 is used, and the WLAN is mapped to VLAN 20. Also, verify the WLC management interface is accessible over HTTPS.

Which TWO statements correctly describe the configuration and verification of IPv4 and IPv6 parameters for host connectivity, including default gateway, DNS, and subnet masks?

Two switches should form an EtherChannel with LACP. One side is set to active and the other is set to passive. If the remaining interface settings match, what is the expected result?

Which TWO statements correctly describe the configuration and verification of IPv4 and IPv6 parameters for host connectivity?

A switch receives BPDUs on a user-facing port configured as an edge port, but instead of just blocking the port role it fully error-disables it. Which protection feature most likely explains that behavior?

A host address is 172.16.8.70/26. What is the network address of its subnet?

Drag and drop the following steps into the correct order to sequence the DNS resolution process from a client query to receiving an A-record response, followed by the diagnostic workflow using nslookup and dig to identify a missing or incorrect A-record.

Drag and drop the following steps into the correct order to configure a switch port for data and voice traffic.

Drag and drop the cable types and transceivers on the left to their corresponding distance limits or interface diagnostics on the right.

Drag and drop the syslog severity levels and NTP concepts on the left to their correct descriptions on the right.

Which rule does a router apply first when selecting a route for a destination packet?

A switchport should allow only one learned MAC address and shut down if a different device is connected later. Which port security violation mode and limit combination best fits that goal?

A router has routes to 192.168.100.0/24 and 192.168.100.128/25. Which route is used for traffic to 192.168.100.140?

Based on the exhibit, why is the static route not being used for 172.18.9.10?

Exhibit: A script sends an HTTP GET request to a controller API endpoint. What is the usual purpose of the GET method?

Drag and drop the following steps into the correct order to configure an LACP EtherChannel on Cisco IOS-XE switches.

A router is performing PAT for inside users. Which detail allows multiple inside sessions to share one public IPv4 address at the same time?

Which single OSI model layer is responsible for both end‑to‑end reliable data delivery and segmenting data into smaller units?

Users in VLAN 60 on switch SW2 cannot reach the default gateway located on switch SW1. The trunk between SW1 and SW2 is operational and allows VLAN 60. What is the most likely reason for this issue?

After a hub was connected to interface Gi0/10, the interface immediately entered errdisable state. The following syslog message was generated: '%PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred on interface Gi0/10.' What is the strongest explanation for why Gi0/10 shut down?

You are connected to the multilayer switch MLS1 in a branch network. The DHCP server on router R1 is supposed to serve the 192.168.20.0/24 VLAN 20, but clients in VLAN 20 are not receiving IP addresses. Additionally, a rogue DHCP server has been detected on VLAN 20. Configure MLS1 to enable DHCP snooping on VLAN 20, set the trust state on the uplink port to R1, and limit the rate of DHCP packets on access ports. Then, on R1, correct the DHCP configuration so that the pool for VLAN 20 uses the correct default-router (192.168.20.1) and DNS server (8.8.8.8), and ensure that the excluded-address range is not too large (exclude only the first 10 addresses). Verify the solution.

What is the correct order of steps to capture and analyze traffic on IOS-XE using the embedded packet capture feature, and in Wireshark to isolate a Layer 2 or Layer 3 fault?

Exhibit: A laptop has IP address 10.20.30.44/27. Which address is its directed broadcast for that subnet?

Which two statements accurately describe software-defined networking and network virtualization concepts at a basic CCNA level?

An ACL permits only tcp 10.10.10.0/24 host 192.0.2.10 eq 443 and has no other permit entries. What happens to an ICMP echo request from 10.10.10.5 to 192.0.2.10?

Which three statements about IPv6 routing are correct? (Choose three.)

Exhibit: Clients can see the corporate SSID but fail authentication after entering valid usernames and passwords. Which issue is the best explanation?

Which three of the following statements about Network Address Translation (NAT) are correct? (Choose three.)

Why is NTP especially useful when devices send logs to a centralized Syslog server?

Which two actions are reasonable examples of basic device-hardening practice?

Which service would a client most directly rely on to convert `server.example.com` into an IP address?

Why is R1 not installing the floating static default route into the routing table?

You are connected to the console of R1. The network uses IPv6 with EUI-64. R1's GigabitEthernet0/0 interface has MAC address 001e.4a7b.9c0d. You need to configure an IPv6 address on this interface using EUI-64, with the subnet 2001:db8:abcd:1::/64.

Drag and drop the following steps into the correct order for the router's routing table lookup process when forwarding a packet to a destination IP address, including the best-path selection logic.

A port connected to an end-user PC should not send or expect VLAN tags from the endpoint. Which interface type is appropriate on the switch?

Which two statements accurately describe OSPF route selection or behavior at the CCNA level?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with an access port G0/1 connected to a server. The network administrator has noticed that the server is sending BPDUs, which could cause network instability. You need to configure PortFast and BPDU Guard on port G0/1 to prevent BPDU-related issues and ensure the port transitions to forwarding state immediately.

A controller-based WLAN uses 5 GHz in an open office. Clients keep disconnecting when users roam between APs, but signal strength remains strong. Based on the exhibit, what is the most likely problem?

You are connected to R1. Configure inter-VLAN routing on R1 using router-on-a-stick so that hosts in VLAN 10 (192.168.10.0/24) and VLAN 20 (192.168.20.0/24) can communicate. The switch SW1 is already configured with VLANs and trunking, but R1's current configuration prevents traffic. Identify and fix the issues.

Why is BPDU Guard commonly enabled on PortFast-enabled access ports?

A host address is 192.168.14.222/28. Which address is the broadcast address of its subnet?

Drag and drop the following OSPFv2 neighbor state transitions into the correct order, starting from the initial Down state on a broadcast or point-to-point network (non-NBMA).

An administrator wants to block all Telnet access to a router’s VTY lines and allow only SSH. Which change most directly supports that goal?

A network engineer configures a primary default route via Gi0/0 (next-hop 192.168.12.2) and a floating static default route via Gi0/1 (next-hop 192.168.12.6) with AD 200. To test failover, the engineer issues the shutdown command on Gi0/0. After this, the router does not have a default route in the routing table. Which problem explains this behavior?

Drag and drop the following steps into the correct order to configure and verify OSPFv3 neighbor adjacency using link-local addresses in area 0.

A network administrator is troubleshooting a Windows 10 workstation that cannot access the internet. The workstation receives an IPv4 address starting with 169.254.x.x. The network uses DHCP, and other workstations on the same subnet are working correctly. What is the most likely cause of this issue?

Drag and drop the following steps into the correct order to configure inter-VLAN routing using a router-on-a-stick topology.

Which static route on R1 sends all unknown IPv4 destinations to next-hop address 192.0.2.1?

Match each service to the kind of problem it most directly helps solve.

A trunk link has a native VLAN mismatch between two switches. What is the most likely result?

Which two statements accurately describe subnet masks in IPv4?

A network troubleshooter is using Cisco IOS-XE's embedded packet capture feature to capture traffic on an interface and then analyze it in Wireshark to isolate a Layer 2 or Layer 3 fault. Which of the following sequences represents the correct order of steps?

Which two statements accurately describe why organizations use separate employee and guest WLANs?

A host address is 192.168.50.158/27. Which address is the network address of its subnet?

A device administrator can log in securely over SSH, but the organization still insists on restricting source IP ranges and keeping detailed logs. Which statement best explains that decision?

You are connected to the console of R1. The network uses IPv6 with EUI-64. R1's GigabitEthernet0/0 interface has MAC address 0011.2233.4455. You must configure the interface to generate an IPv6 link-local address using the 'ipv6 enable' command, and also assign a global unicast address 2001:db8:1::/64 using EUI-64. The interface is currently administratively down.

You are connected to R1 via the console. R1 is configured as an NTP client that should synchronize with the NTP server at 203.0.113.1. You need to verify that R1 is synchronizing correctly and also ensure that the system clock is updated. Additionally, configure R1 to act as an NTP server for downstream devices on the internal network 192.168.1.0/24.

Which two statements accurately describe DNS and DHCP?

Drag and drop the following steps into the correct order to configure and verify HSRP with priority and preemption on an interface.

An administrator connects a new access-layer switch to a distribution switch. The link comes up but remains in a blocking state and does not forward frames. The administrator issues the show command shown in the exhibit. What is the most likely reason the link is blocked?

A router has routes to 192.168.0.0/16 and 192.168.50.0/24. Which route is used for traffic to 192.168.50.99?

After a switch replacement, users in VLAN 30 cannot reach devices in other VLANs. The replacement switch has a trunk link to the distribution switch that shows as up/up. What is the most likely cause?

Based on the exhibit, which configuration should be added to restore DHCP service for clients in VLAN 30?

Refer to the exhibit. A network administrator is troubleshooting why not all OSPF neighbors are fully adjacent on a multi-access broadcast segment. After issuing the show ip ospf neighbor command on R1, the output is displayed. What is the most likely cause of the 2WAY/DROTHER state for neighbor 172.16.1.1?

A switch administrator enters the following commands on interface GigabitEthernet1/0/10: interface g1/0/10 switchport mode access switchport access vlan 30 spanning-tree portfast spanning-tree bpduguard enable A user connects a small managed switch to this port, and the access port immediately changes to an err-disabled state. Which feature caused the port to shut down?

A network engineer configures a static route: ip route 192.168.10.0 255.255.255.0 10.1.1.2. The next hop 10.1.1.2 is reachable via OSPF. Later, the engineer notices that the route to 192.168.10.0/24 has disappeared from the routing table. What is the most likely cause?

Which two statements accurately describe the value of named administrative accounts?

Refer to the exhibit. A network engineer is troubleshooting a connectivity issue on R1. The serial link to R2 on interface Serial0/1 is using HDLC encapsulation, and the physical cable has been verified as good. The engineer has confirmed that the encapsulation type matches on both routers and that the clock rate is correctly configured on the DCE end. Based on the output, what is the most likely cause of the line protocol down state on Serial0/1?

A router advertises its LAN network into OSPF, but no OSPF Hellos should be sent toward end-user devices on that LAN. Which configuration approach solves this cleanly?

Match each route source or route type to its most accurate description.

Which OSPF network type on Ethernet performs a DR and BDR election by default?

Which two statements accurately describe why NetFlow is useful for operations teams?

An administrator sees high interface utilization through SNMP graphs but wants to identify which conversations are responsible. Which addition best closes that visibility gap?

Which TWO statements correctly describe the configuration and verification of EtherChannel with LACP?

Why is a default route useful on a small branch router connected to a single upstream provider?

A network technician is troubleshooting connectivity between two directly connected Cisco switches. Hosts on VLAN 10 connected to SwitchA cannot ping the default gateway on SwitchB. The interface on SwitchB shows up/up, but the interface on SwitchA shows up/down. The technician examines the interface configuration and status on SwitchA. What is the most likely cause of this issue?

You are connected to the console of R1. The network administrator reports that hosts on VLAN 10 cannot ping the default gateway (192.168.10.1). R1's GigabitEthernet0/1 is connected to a switch with trunk port allowing VLAN 10 and 20. The interface configuration on R1 appears correct, but the VLAN 10 interface is not operational.

You are connected to R1 via the console. R1 and R2 are configured with EIGRP AS 100. R1 has two paths to the 172.16.1.0/24 network: one via a FastEthernet link to R2 (bandwidth 100 Mbps, delay 100 microseconds) and another via a serial link to R2 (bandwidth 1.544 Mbps, delay 20000 microseconds). The EIGRP metric is calculated using the default K-values. The FastEthernet link is preferred, but you need to make the serial link the backup by adjusting the administrative distance.

A host is configured as 192.168.50.130/25. Which address is the broadcast address for its subnet?

A network engineer queries a REST API and receives data in JSON format. Which statement about JSON is correct?

Match each REST-style method to the most common intent.

Which two statements accurately describe WPA2 and WPA3 in wireless security?

You are connected to R1. The network uses a router-on-a-stick design with a single switch (SW1) and two VLANs (10 and 20). Currently, hosts in VLAN 10 cannot ping hosts in VLAN 20, and the trunk between R1 and SW1 shows a native VLAN mismatch. Examine the provided configuration and output, then apply the necessary corrections to R1 so that inter-VLAN routing works correctly.

You are connected to R1. Configure NTP client so that R1 synchronizes with the NTP server at 198.51.100.10, using its Loopback0 (10.0.0.1/32) as the source interface. Also configure syslog to send messages of severity 5 (notifications) and above to 192.0.2.20. The current configuration shows a misconfigured NTP server address and an incorrect logging trap level. Verify with 'show ntp status' (stratum should not be 16) and 'show logging'.

A router has an OSPF-learned route to a destination prefix and also a directly connected route to a broader supernet that includes that destination. The OSPF route is more specific. Which route is used for the destination?

Which two tasks are strong candidates for network automation? (Choose two.)

Users can reach a server by IP address but not by hostname. Which service should be checked first?

Why is a default route often described as a route of last resort?

A network engineer notices that a newly connected switch-to-switch link is up, but traffic from multiple VLANs is not passing. When issuing the show interfaces trunk command, no trunk ports are listed. Both switch ports are configured with switchport mode dynamic auto. What is the most likely cause?

Two switches, SW1 and SW2, are connected via a trunk link. Hosts in VLAN 50 on SW1 cannot communicate with hosts in VLAN 50 on SW2, while hosts in other VLANs communicate normally. What is the most likely cause?

You have console access to both R1 and R2. Configure OSPFv2 on both routers to establish a single-area adjacency in area 0. The link between R1 and R2 uses 10.0.0.0/30. Currently, OSPF is not configured on either router. After configuration, verify the adjacency forms and routes are exchanged.

Which two statements accurately describe APIs in controller-based networking?

R1 and R2 are directly connected and both configured for OSPF area 0. The IP addresses are correct, but the routers do not become neighbors. What is the most likely cause?

Why are data models such as YANG important in network automation?

Users report that their PCs take over 30 seconds to obtain IP addresses and reach the network after being powered on. A network technician checks a switch port connected to a PC and observes that the port transitions through blocking, listening, learning, and then forwarding states, taking about 30 seconds to complete. The switch is running standard 802.1D STP. The technician confirms the port is an access port and only connects to a PC. What should the technician do next?

You are connected to the console of R1. The output of 'show interfaces serial0/0/0' displays that the interface is administratively down (status: administratively down, line protocol is down). The network administrator reports that the serial link between R1 and R2 was recently configured but is not working. You need to troubleshoot and restore connectivity. The serial interface on R1 is Serial0/0/0, and the link is a point-to-point HDLC connection.

Refer to the exhibit. A network engineer is troubleshooting a connectivity issue between two routers connected via a serial link. The engineer runs the show interfaces Serial0/0/0 command on R1. Based on the output, what is the most likely cause of the problem?

Drag and drop the following steps into the correct order to enable a third-party SFP transceiver and verify its diagnostics on a Cisco switch.

A phone and PC share one switchport. The phone works, but the PC cannot reach its normal data resources. The switchport voice VLAN is configured, and the access VLAN is incorrect. Which explanation is strongest?

You are connected to R1 via console. R1 is connected to R2 via GigabitEthernet0/0 (10.0.0.1/30) and to R3 via GigabitEthernet0/1 (10.0.0.5/30). R1 has a management subnet 192.168.1.0/24 connected to GigabitEthernet0/2. The network administrator wants to ensure that traffic from the management subnet to the Internet (203.0.113.0/24) uses R2 as the primary path and R3 as a backup. Currently, OSPF is running with default metrics. You must configure a floating static route that will be used only if the OSPF route fails.

Which TWO statements correctly describe the behavior of Rapid PVST+ in a Layer 2 network?

Which two actions help protect access-layer switch ports from rogue DHCP servers?

A network administrator is troubleshooting connectivity issues in a switched network. Users on VLAN 10 report intermittent connectivity to the server farm. The network uses Rapid PVST+ as the spanning-tree protocol. The administrator examines the switch that is the root bridge for VLAN 10 and notices that one of the uplink interfaces to an access switch is in a blocking state. What is the most likely cause of this issue?

A network engineer notices that clients in the 192.168.10.0/24 subnet are receiving the IP address 192.168.10.1 from the DHCP server, causing a duplicate IP conflict with the router’s own interface. What is the most likely cause?

A network engineer at a large enterprise observes repeated spikes in latency on the core network every weekday at 10:00 AM, but no corresponding increase in overall bandwidth utilization. The engineer wants to use AI/ML to automatically identify the root cause and take corrective action without manual intervention. Which concept best describes this approach?

A network administrator is troubleshooting an issue where internal hosts can ping the company's web server by IP address (192.0.2.10) but cannot access it using the fully qualified domain name www.example.com. The DNS server (192.0.2.5) is reachable and responds to queries. The administrator runs nslookup www.example.com from a host and receives the following output: C:\> nslookup www.example.com Server: UnKnown Address: 192.0.2.5 Name: www.example.com Address: 192.0.2.20 Based on the output, what is the most likely cause of the problem?

You are connected to R1 via the console. R1 is a Cisco ISR 4321 router running IOS-XE 17.3. The network team has reported intermittent connectivity issues between VLAN 10 hosts and the server at 10.0.0.100. You suspect a routing problem and need to analyze the IP routing table, ARP cache, and interface status to identify the cause. Use the provided outputs to diagnose the issue.

Based on the exhibit, what is the most likely reason PAT is not working correctly?

A host address is 192.168.88.66/27. Which address is the network address of the subnet?

Drag and drop the following steps into the correct order to troubleshoot a suspected duplex mismatch and CRC errors on a Cisco switch interface.

You are connected to R1 via the console. R1 is a Cisco IOS-XE router. The network manager wants to use an Ansible playbook to configure a loopback interface with IP address 10.0.0.1/24 on R1. You need to write the Ansible YAML playbook that connects to R1 and configures this interface. The playbook must not use the 'parents' argument in the ios_config module.

Why does traceroute reveal each router hop along a path?

Which THREE statements correctly describe the configuration of AAA with RADIUS or TACACS+ on Cisco IOS-XE?

Why is HTTPS usually preferred over HTTP when accessing controller APIs?

Drag and drop the following steps into the correct order to troubleshoot a client PC that cannot connect to a remote web server.

Which command places a switch port into access mode directly?

Which two statements accurately describe JSON?

You are connected to R1 via the console. The network has a DNS server at 203.0.113.10 that should resolve www.example.com to 203.0.113.100. However, when you ping www.example.com, it fails. Diagnose and resolve the DNS resolution issue. The DNS server is reachable via ping, but nslookup from R1 returns a server failure. Configure R1 so that it can successfully resolve www.example.com. Additionally, verify that the DNS server is correctly configured for forward and reverse lookups.

Users in 10.10.10.0/24 must be prevented from reaching the web server at 172.16.1.10 over HTTP, but all other traffic should be allowed. Which ACL entry best matches the requirement?

Match the security feature to its main purpose.

Exhibit: OSPF neighbors are not reaching FULL state on an Ethernet segment with multiple routers. The output of show ip ospf neighbor on R2 shows a neighbor in the 2WAY/DROTHER state. What is the most likely reason?

What problem does Spanning Tree Protocol solve in a switched network?

An engineer configures a floating static route to 0.0.0.0/0 with an administrative distance of 200 while OSPF is providing a default route. What is the intended behavior?

Which two statements accurately describe controller-based networking?

Drag and drop the following steps into the correct order to configure a Windows 10 host with a static IPv4 address, subnet mask, and default gateway.

SW1 is the root bridge for VLAN 10. A user switch receives a BPDU on an access port connected to a desk-side unmanaged switch. What should happen if BPDU Guard is enabled on that port?

You are connected to R1. The network administrator reports that hosts on VLAN 10 cannot communicate with the server attached to R2's GigabitEthernet0/1 interface. Troubleshoot and resolve the issue. Identify the root cause and apply the necessary fix on R1.

A router learns the same destination from EIGRP and OSPF. The EIGRP route has a metric of 1000, and the OSPF route has a metric of 10. Which route is installed by default?

Drag and drop the protocols/technologies on the left to the descriptions on the right.

Based on the exhibit, why are clients in VLAN 70 failing to resolve hostnames even though they can reach remote IP addresses?

A router learns 172.16.0.0/16 from OSPF and 172.16.10.0/24 from a static route. Which route is used for traffic to 172.16.10.55?

Match each service or visibility technology to the most appropriate use case.

Drag and drop the following steps into the correct order to configure and verify HSRP on a router interface.

An internal server must always be reachable from outside using the same public IP address. Which translation approach is most appropriate?

Drag and drop the VLAN/trunking commands and terms on the left to their correct descriptions or functions on the right.

Which three of the following are characteristics of wireless LAN (WLAN) operation in the 2.4 GHz and 5 GHz bands? (Choose three.)

Which TWO statements accurately describe the characteristics and deployment considerations for fiber optic cabling in a modern enterprise network?

Why is JSON often preferred over completely unstructured text in API responses?

Exhibit: A wireless client can see the SSID and associates successfully, but it never gets network access. Other users on the same SSID work. Which issue is the best fit?

Which TWO statements correctly describe OSPFv2 router-id selection and verification in a single-area configuration?

A network engineer checks EtherChannel status on a switch and sees the following output: Group Port-channel Protocol Ports ------+-------------+---------+----------------------------- 1 Po1(SD) LACP Gi1/0/1(s) Gi1/0/2(I) What is the most likely reason the EtherChannel is not forwarding traffic?

A host address is 192.168.1.14/29. Which address is the broadcast address for that host’s subnet?

Drag and drop the following steps into the correct order to configure OSPFv3 for IPv6 on a Cisco router.

A host receives a correct IP address and subnet mask from DHCP but still cannot reach remote networks. Local subnet communication works. Which missing DHCP option is the strongest suspect?

You are troubleshooting a wireless client association failure on a Cisco WLC. The client is unable to connect to the corporate SSID 'CorpNet' and reports an authentication error. Review the WLC configuration and fix the issue so that the client can associate and obtain an IP address from VLAN 100. The WLC management IP is 192.168.1.10/24.

A network engineer is troubleshooting an issue where a Windows 10 workstation (Host-A) cannot reach the internet, but can ping the local default gateway. The engineer runs 'ipconfig /all' on Host-A and reviews the output. What is the most likely cause of the problem?

Why are tokens commonly used in API workflows instead of sending raw credentials with every request?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two links to SW2 configured as an EtherChannel using LACP. The EtherChannel is not coming up. Interface G0/2 was accidentally configured as an access port in VLAN 10, while G0/1 is configured as a trunk. The administrator wants to use LACP to bundle the links. Troubleshoot and fix the configuration to bring up the EtherChannel.

You are connected to R1. The link between R1 and R2 is experiencing intermittent connectivity and poor performance. Review the provided show interface output to identify the root cause(s) of the issue, then apply the necessary configuration changes to resolve the problem and restore full connectivity. Output from R1: ``` GigabitEthernet0/0 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is aaaa.bbbb.cccc (bia aaaa.bbbb.cccc) Internet address is 192.168.1.1/30 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Half-duplex, 100Mb/s, link type is auto, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters 00:01:23 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 150 packets input, 1500 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 150 input errors, 150 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 200 packets output, 2000 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out ```

A network team wants routers and switches to have consistent timestamps in logs so event correlation is accurate during an outage. Which service should they verify first?

A network engineer is evaluating monitoring technologies for a large enterprise network that requires high-frequency, low-latency traffic data collection with support for custom fields. The solution must also support encryption and authentication to prevent tampering. Which technology best meets these requirements?

A router is configured with a static NAT mapping for an internal server. What is the main operational advantage of this design for outside clients?

Which TWO statements correctly describe aspects of interpreting packet capture output for Layer 2/3 troubleshooting using Wireshark or embedded packet capture on IOS-XE?

Refer to the exhibit. A network engineer is troubleshooting DHCP issues on a branch office network. Several users report that new devices are unable to obtain IP addresses, even though the DHCP pool configured on R1 appears to have sufficient free addresses. The engineer executes the show ip dhcp conflict command and observes the output. Based on the output, what is the most likely cause of the problem?

SW2 receives the following STP details for VLAN 10: The root bridge ID is 32768:0001.0001.0001 (SW1), and SW2's bridge ID is 32768:0002.0002.0002. Its interface Gi0/1 has a path cost of 4 to the root, while Gi0/2 has a path cost of 19. Based on this information, which statement is correct?

You are connected to SW1 via the console. SW1 is a Layer 2 switch connected to two other switches (SW2 and SW3) via redundant links. All switches run IEEE 802.1D Spanning Tree Protocol. The network administrator wants SW1 to become the root bridge for VLAN 1. Currently, the root bridge is SW2. Configure SW1 to achieve this and ensure that port G0/1, which connects to an end device, immediately transitions to forwarding state upon link up and is protected from BPDU attacks.

You are troubleshooting connectivity between R1 and R2. The link is down, and you need to identify and fix the issue. Examine the provided 'show interfaces' output and running configuration, then apply the necessary commands to restore connectivity.

Which two statements accurately describe why NTP and Syslog are often configured together?

Exhibit: PCs in VLAN 20 are not receiving addresses from a DHCP server in another subnet. The switch SVI for VLAN 20 is up, and routing is working. Which configuration is most likely missing on the gateway for VLAN 20?

Refer to the exhibit. An administrator is trying to access a web server in the DMZ at 192.168.1.10 using HTTPS, but the connection times out. The web server is confirmed to be running and listening on both port 80 and port 443. The administrator examines the access list configuration on the perimeter router. Based on the output of the show access-lists command, what is the most likely cause of the failure?

An administrator wants to prevent users from browsing to one specific web server while still allowing them to reach other web destinations. Which ACL design principle is most important here?

A router learns a route to 172.16.0.0/16 via OSPF (administrative distance 110) and a route to 172.16.10.0/24 via EIGRP (administrative distance 90). No other overlapping routes exist. Which TWO statements about how the router handles these routes are correct?

Match each controller or automation term to its most accurate description.

An engineer wants all devices to send logs to 10.10.10.50 and also stamp those logs with consistent time from 10.10.10.60. Which two configurations are required on a Cisco device?

A user can authenticate successfully to a network device but is denied access to certain commands. Which statement best explains the situation?

A network technician is troubleshooting a connectivity issue where a host cannot communicate with a remote server. The technician notices that frames are being dropped at an intermediate switch. At which OSI model layer does the switch primarily operate, and what is the Protocol Data Unit (PDU) used at that layer?

Which TWO statements about IPv4 and IPv6 static routes, including floating static routes, are correct?

A switch receives superior BPDUs on a port where the design requires that no downstream device ever become the root path for that segment. Which feature is the best fit for that requirement?

A network administrator wants to receive an immediate notification from a device when a significant event occurs, rather than polling the device repeatedly. Which SNMP feature is most associated with that requirement?

You are connected to SW1, a Cisco switch that is experiencing intermittent connectivity issues. The network administrator suspects a duplex mismatch between SW1 and the connected router R1. Use CDP to verify the status and check interface statistics.

A switchport should automatically disable itself if too many MAC addresses are learned beyond the configured secure limit. Which port-security violation mode causes that behavior?

A user can connect to the employee SSID and receive the correct employee IP subnet, but access to one internal application fails only for that WLAN while wired users succeed. Which troubleshooting area is the strongest first focus?

A subnet must support 30 usable IPv4 host addresses. Which prefix is the smallest that meets the requirement?

Exhibit: A standard ACL meant to block host 10.10.10.50 from reaching any remote network was applied inbound on the branch router's LAN interface, but users report that all local traffic from that host is now blocked. What is the better placement?

R1 has the following static route configured: ip route 0.0.0.0 0.0.0.0 203.0.113.1 What does this route accomplish?

Why is the combination of strong authentication and centralized logging better than either control by itself?

A phone and a PC are attached to the same switchport. The intended data VLAN is VLAN 10, and the phone uses voice VLAN 20. The switchport currently has `switchport voice vlan 20` configured. The phone works, but the PC cannot reach the data network. Which command is most likely missing?

Users can browse websites by IP address but not by hostname. The default gateway is reachable and general internet connectivity works. Which two causes are the most likely?

Which two statements accurately describe why DNS issues can look like general connectivity problems to users?

Two switches are connected with EtherChannel using LACP. One side is configured with mode active and the other side with mode passive. What happens?

R1 and R2 are connected via Ethernet and are configured with OSPF, but they fail to form an adjacency. Upon checking the interface configurations, you see that R1’s interface is in OSPF area 0 while R2’s interface is in area 1, and both interfaces use default timers and are in the same subnet. What is the most likely reason?

You are connected to R1, a multilayer switch acting as a DNS forwarder for two VLANs. Users on VLAN 10 report that they cannot resolve 'files.example.com' while VLAN 20 works fine. The DNS server 198.51.100.53 is reachable but returns SERVFAIL for queries from subnet 192.168.10.0/24, while server 203.0.113.53 responds correctly for both VLANs. Diagnose and fix the DNS resolution issue using nslookup and dig, then adjust the IOS-XE configuration to ensure proper name resolution. Choose the best fix that permanently resolves the problem.

A small office wants branch routers to automatically hand out IP addresses, default gateway values, and DNS servers to clients. Which service should be configured?

Two switches are connected using four Gigabit Ethernet interfaces configured as an EtherChannel with LACP. The network administrator notices that only two of the four interfaces are active in the port-channel, and the other two are in a suspended state. Upon further investigation, the administrator finds that the two inactive interfaces correspond to remote interfaces that are configured with the 'on' mode, while the active ones correspond to remote interfaces configured with LACP active/passive. The administrator also verifies that all local interfaces have the same speed, duplex, and VLAN. What is the most likely cause of the suspended interfaces?

Drag and drop the following steps into the correct order to describe the router's routing table lookup process for a destination IP address, including the best-path selection logic (longest prefix match, then administrative distance, then metric) and the final forwarding decision.

You are connected to R1. The inside network 192.168.1.0/24 must be able to reach the internet via PAT (overload) using the public IP 203.0.113.1 on interface GigabitEthernet0/1. Additionally, a web server at 192.168.1.10 must be reachable from the internet via static NAT to 203.0.113.10. The current configuration is not working. Identify and fix all issues.

You are connected to SW1 via console. SW1 is a Layer 2 switch connected to two other switches (SW2 and SW3) via trunk links. The network administrator wants to ensure that SW1 becomes the root bridge for VLAN 10 and VLAN 20. Currently, SW2 is the root for both VLANs. Configure SW1 to become the root bridge for these VLANs using the Cisco-recommended macro STP commands.

A router has a connected route to 192.168.1.0/24 and also has a default route. Which route is used for traffic to 192.168.1.55?

Drag and drop the following steps into the correct order to install a new fiber optic link between two switches, including SFP insertion and basic troubleshooting.

You are connected to a multilayer switch MLS1. Configure Root Guard on switchport GigabitEthernet 0/1 (connected to an unauthorized switch) so that if a superior BPDU is received, the port is blocked instead of causing a topology change. Also enable Loop Guard on uplink GigabitEthernet 0/2 (connected to the root bridge) to prevent unidirectional link issues. Finally, enable BPDU Guard on PortFast-enabled access port GigabitEthernet 0/3 (connected to a host) so that if a BPDU is received, the port goes err-disabled. After configuration, a superior BPDU is received on G0/1 and the port is blocked; a BPDU is received on G0/3 and the port goes err-disabled. Verify these protections are active.

Drag and drop the following steps into the correct order to troubleshoot and resolve excessive interface errors caused by a duplex mismatch on a Cisco switch interface.

You are connected to SW1 via the console. SW1 is a Layer 2 switch connected to multiple PCs. The network administrator wants to implement port security on port G0/1 to allow only one MAC address and to shut down the port if a violation occurs. Additionally, the administrator wants the MAC address to be learned dynamically and added to the running configuration as sticky. Configure port security on G0/1 accordingly.

You are connected to Switch1. Configure an LACP EtherChannel between Switch1 and Switch2 using interfaces GigabitEthernet0/1 and GigabitEthernet0/2. The channel must be in active mode on both sides, and the port-channel interface must have VLAN 10 as the access VLAN. The current configuration has a speed/duplex mismatch and inconsistent VLAN assignments preventing the channel from forming. Verify the channel is up using 'show etherchannel summary'.

Refer to the exhibit. A network administrator is troubleshooting an NTP synchronization issue on R1. The router is configured with the command ntp server 10.1.1.100, but the clock remains unsynchronized. The administrator issues the show ntp status command. What is the most likely cause of the problem?

You are connected to R1 via console. R1 is directly connected to R2 over a 1000BASE-T link that is failing to come up. Configure interface GigabitEthernet0/0 on R1 with the correct speed and duplex settings to match R2's configuration, and then verify the link is operational. Additionally, determine the appropriate SFP type for a new 40 km fiber link between R1 and R2.

Which security concept gives a user only the permissions required to perform assigned tasks and nothing more?

You are managing a Cisco WLC (192.168.1.10) via its web UI. The wireless network 'CorpSecure' has been configured but clients cannot associate. Some report 'wrong password' errors; others see the SSID but fail to connect. Additionally, management access to the WLC web UI is intermittent. Identify and resolve the issues so that wireless clients can successfully associate with 'CorpSecure' using WPA3-Personal and the WLC web UI is reliably accessible from the management VLAN (VLAN 10).

An EtherChannel between two switches is configured for LACP. One switch shows the member interfaces as bundled, while the other shows them as individual interfaces. Which explanation is most likely if both sides are using LACP?

Which three of the following statements about the routing table lookup process on a Cisco router are true? (Choose three.)

Exhibit: SW2 receives superior BPDUs on both uplinks. One uplink becomes the root port and the other becomes alternate. Which factor is considered first when SW2 chooses the root port?

Exhibit: R1 has the static route 'ip route 0.0.0.0 0.0.0.0 192.0.2.2 200' and also learns a default route from OSPF. Which default route will be installed while the OSPF route is present?

Match each automation transport or interaction term to its most accurate description.

R1 and R2 should form an OSPF adjacency on their shared GigabitEthernet link, but they remain stuck in EXSTART. What is the most likely cause?

You are connected to WLC-1 via SSH. A new SSID 'CorpSecure' must be configured for 5 GHz clients using WPA3-Personal. However, after creation, clients can see the SSID but fail to associate. Review the WLC configuration and fix the issue so that clients can successfully associate and obtain an IP address from VLAN 100 (subnet 10.0.100.0/24).

A router shows the following route: O 10.10.40.0/24 [110/20] via 192.0.2.2, 00:00:12, GigabitEthernet0/0 What does the value 110 represent?

Which two statements about NTP are correct? (Choose two.)

A network engineer notices that R1 is using the static route to 192.168.10.0/24 via next-hop 10.1.1.2 instead of the OSPF route via 10.2.2.2, even though the OSPF path has lower latency. What is the most likely cause?

Given the JSON snippet below, what is the value of hostname? { "device": { "hostname": "R1", "mgmt_ip": "192.0.2.10" } }

A network administrator is troubleshooting connectivity issues between two switches. Hosts connected to Switch A cannot ping hosts on Switch B. The link between the switches shows as up/up on both ends, but interface error counters (CRC, runts) are increasing rapidly. What should the administrator do to resolve the issue?

Which two statements about standard and extended IPv4 ACLs are correct?

Drag and drop the following steps into the correct order to configure and recover from a BPDU guard violation on a PortFast-enabled access port.

Which two statements accurately describe why source restriction and logging are often used together for administrative access?

Drag and drop the following steps into the correct order to configure a Cisco IOS-XE router as a DHCP relay agent and verify the DHCP DORA process for a client on a remote subnet. OPTIONS: A: Configure the ip helper-address command on the interface facing the client, then verify connectivity to the DHCP server, and finally capture the DORA process using debug ip dhcp relay. [CORRECT] B: Configure the ip helper-address command on the interface facing the DHCP server, then verify connectivity to the client, and finally capture the DORA process using debug ip dhcp server packet. C: Configure the ip dhcp relay information option command on the interface facing the client, then verify connectivity to the DHCP server, and finally capture the DORA process using debug ip dhcp server packet. D: Configure the ip helper-address command on the interface facing the client, then capture the DORA process using debug ip dhcp server packet, and finally verify connectivity to the DHCP server.

Which field is modified by each router hop in an IPv4 packet to prevent endless forwarding loops?

Which spanning-tree port role receives the best BPDU toward the root bridge on a nonroot switch?

You are connected to SW1 via the console. SW1 is a Layer 2 switch connected to router R1 via trunk link G0/1. R1 performs inter-VLAN routing using subinterfaces. VLANs 10, 20, and 30 exist on SW1. Hosts in VLAN 10 (192.168.10.0/24) can ping R1's subinterface, but cannot communicate with hosts in VLAN 20. You suspect the trunk is not allowing VLAN 20 traffic.

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two VLANs: VLAN 10 (Sales) and VLAN 20 (Engineering). A router R1 is connected to port G0/1 on SW1 for inter-VLAN routing. Currently, the router is not routing between VLANs because the trunk is not configured correctly. Configure the switch port as a trunk and ensure the router can route between VLANs using subinterfaces (Router-on-a-Stick).

The SVI for VLAN 20 has `ip nat outside` and the WAN interface has `ip nat inside`. Hosts in VLAN 20 must reach the internet through PAT, but users report no external connectivity. Which configuration issue best explains the problem?

Drag and drop the following steps into the correct order to configure spanning-tree protection features including BPDU Guard, Root Guard, and Loop Guard on a Cisco switch.

You are connected to R1 via console. R1 connects three subnets: 10.0.1.0/24 (area 0), 10.0.2.0/24 (area 0), and 10.0.3.0/24 (area 0). The serial link to R2 uses IP subnet 10.0.0.0/30 and is in OSPF area 1. The network administrator wants to advertise a single summary route for these three subnets to R2, reducing the OSPF link-state database size in area 1. R1 is already running OSPF with network statements for its connected subnets in their respective areas. You need to configure route summarization on R1 so that only the summary route is advertised to R2 via the serial link.

Drag and drop the following steps into the correct order to sequence the DNS resolution process from a client query to receiving an A-record response, followed by the nslookup and dig diagnostic workflow for troubleshooting missing or wrong DNS records.

Which TWO of the following statements accurately describe the configuration and behavior of Root Guard, Loop Guard, and BPDU Guard in Rapid PVST+ environments?

After hardening SSH by disabling password authentication and restricting access to an ACL permitting only the management subnet 10.1.10.0/24, configuring RADIUS AAA authentication, enabling port security with a maximum of two MAC addresses on all access ports, and implementing DHCP snooping and DAI on VLAN 10, the administrator finds that users in VLAN 10 obtain DHCP addresses and access the network normally, but SSH from the management workstation (10.1.10.20) to the switch fails with timeouts.

You are connected to R1 (192.0.2.1/24, management IP). The network team needs to automate interface configuration using RESTCONF. Construct a valid RESTCONF GET request to retrieve the operational status of GigabitEthernet0/1 using the ietf-interfaces YANG module, and a PATCH request to set the description of that interface to 'Link to R2' using the Cisco-IOS-XE-native YANG module. Identify the error that occurs if the Accept header is set to application/json instead of application/yang-data+json.

Exhibit: SW1 is configured for EtherChannel with LACP, but the bundle does not form. What is the most likely cause?

You are connected to R1 via the console. The network currently uses EIGRP as its IGP, but you recently configured a static default route toward R2 (next-hop 203.0.113.2) to reach the Internet. However, traffic from R1 to the Internet is not taking the expected path. Examine the provided routing table and partial configuration, then fix the issue so that the static default route is used only when the EIGRP-learned default route is unavailable.

Which TWO statements correctly describe the encapsulation process at the OSI model Transport layer?

Which TWO statements correctly describe the differences between RADIUS and TACACS+ when configuring AAA on IOS-XE?

You are connected to R1. The network has two routers (R1 and R2) connected via a serial link (S0/0/0). R1's GigabitEthernet0/0 connects to the 192.168.1.0/24 LAN. An extended ACL must be configured on R1 to permit only HTTPS traffic (TCP port 443) from host 192.168.1.10 to server 203.0.113.5 (reachable via R2), and deny all other traffic from the LAN to the server. Currently, the ACL is applied inbound on G0/0 but valid HTTPS traffic is being blocked. Troubleshoot and fix the configuration.

Which IPv6 protocol function replaces ARP?

You are connected to a multilayer switch MLS1. The network has two other switches: SW2 and SW3. The interface GigabitEthernet0/1 already has PortFast and BPDU Guard enabled. Configure MLS1 as the root bridge for VLAN 10 and VLAN 20 using the root primary command. After configuration, verify that the interface is not in err-disabled state and that the root bridge role is correctly assigned.

Which two statements accurately describe APIs in network automation?

You are connected to R1. Configure OSPFv2 on R1 and R2 so that they form a full adjacency and can exchange routes. The current configuration has mismatched hello/dead timers blocking the adjacency. Adjust only the necessary settings on R1 to match R2's OSPF timers.

An engineer receives API output that starts with curly braces and contains name-value pairs. Which data format is being used?

Which TWO statements about floating static routes and default routes are correct?

A switchport on one side of a link is configured as a trunk, but the peer side is configured as an access port. What is the most likely result?

You are connected to R1. The network uses DNS to resolve hostnames for remote device management. Currently, R1 cannot resolve the hostname 'ServerA' via DNS. Using the nslookup and dig commands, you have gathered the following outputs: nslookup ServerA Server: 203.0.113.1 Address: 203.0.113.1#53 Name: ServerA.example.com Address: 203.0.113.10 dig ServerA ... ;; ->>HEADER<<- opcode: QUERY, status: NXDOMAIN, id: ... ... The show running-config command shows that 'ip domain-lookup' is enabled, the name-server is 203.0.113.1, and no static host entries are configured. Diagnose and fix the DNS resolution failure. Ensure that R1 can successfully resolve 'ServerA' to its intended IP address 198.51.100.10.

Clients on a network can browse the internet by IP address but fail when using hostnames. What is the most likely problem?

On a router performing NAT, where should ip nat inside be applied?

Drag and drop the following steps into the correct order to configure and verify HSRP active/standby election, including priority, preempt, virtual IP, and failover verification.

A host uses the subnet mask 255.255.254.0. Which prefix length does this represent?

A switchport is configured as a trunk on one side and access on the other side of the same physical link. What is the most likely result?

Users in 10.10.10.0/24 must be prevented from reaching the web server at 172.16.1.10 over HTTP, but all other traffic should be allowed. Which ACL entry should appear first in the ACL?

A controller exposes a YANG-modeled interface configuration through an API. Which two statements correctly describe the purpose of YANG in that workflow?

A network engineer is troubleshooting connectivity issues for hosts in VLAN 10. Hosts in VLAN 10 are unable to ping the default gateway at 192.168.10.1. The engineer checks the switch configuration and notices that the SVI for VLAN 10 is configured with an IP address, but the interface is in a down/down state. What is the most likely cause of this issue?

Which TWO statements are true regarding VLAN configuration, 802.1Q trunking, and the native VLAN?

You are connected to R1. Configure AAA with a RADIUS server at 10.0.0.2 using key 'cisco123' for authentication. Then troubleshoot why 802.1X on interface GigabitEthernet0/1 remains in unauthorized state. Ensure that the default login authentication uses RADIUS first, then local fallback, and fix any configuration issues that prevent 802.1X from working.

You are connected to a multilayer switch MLS1. Configure Root Guard on the designated port facing another switch SW2 to prevent it from becoming root, configure Loop Guard on the uplink port to the core, and configure BPDU Guard on a PortFast-enabled access port. After configuration, a superior BPDU arrives on the designated port—confirm it is blocked by Root Guard. Then, simulate a BPDU on the access port to verify it goes err-disabled due to BPDU Guard.

A host can reach other devices on its local subnet, but it cannot reach remote networks. The host has a valid IP address and subnet mask. Which missing item is the strongest suspect?

Drag and drop the following steps into the correct order to troubleshoot a suspected duplex mismatch and CRC errors on a Cisco switch interface using CLI commands.

After enabling Dynamic ARP Inspection on VLAN 20, a network engineer notices that some hosts lose connectivity. The affected hosts have correct IP addresses and MAC addresses, but they cannot ping the default gateway. All other hosts on the same VLAN work fine. Further investigation reveals that the non-functioning hosts are using static IP configurations, while the working hosts are DHCP clients. What is the most likely cause?

Which three of the following are benefits of integrating AI into network operations? (Choose three.)

Why is a northbound API especially useful in a controller-based network architecture?

You are connected to R1 via console. R1 and R2 are directly connected via GigabitEthernet0/0. Configure OSPF process 1 on both routers so that they form a full adjacency. R1's router-id must be 1.1.1.1, and R2's router-id must be 2.2.2.2. Use network statements to advertise the direct link. Ensure that R1 does not send OSPF hellos out of its GigabitEthernet0/1 interface. The current configuration on R1 has mismatched hello and dead timers, and an incorrect network type, preventing adjacency. Fix all issues.

Which of the following correctly describes the sequence of the TCP three-way handshake between a client and a server?

A host is configured as 10.20.30.95/27. Which address is the network address of its subnet?

You are connected to R1 via the console. R1 is a router that connects to the internet via GigabitEthernet0/0 (198.51.100.1/30) and to the internal network via GigabitEthernet0/1 (10.1.1.1/24). You need to implement a security policy that permits HTTP traffic (port 80) from the internal network to a web server at 10.1.1.100, and denies all other traffic from internal hosts to the internet. The ACL should be named 'INTERNET-FILTER' and applied inbound on GigabitEthernet0/1.

Drag and drop the following steps into the correct order to plan, configure, and apply an extended ACL that permits web traffic from the 10.1.1.0/24 network to the server 192.168.2.10 while blocking all other traffic inbound on GigabitEthernet0/1.

Which TWO DHCP snooping trust states are valid on a Cisco switch? (Choose two.)

Based on the exhibit, why is traffic to 192.168.40.200 using the default route instead of the intended static route?

An administrator notices that hosts in VLAN 30 on SW1 cannot communicate with hosts in VLAN 30 on SW2, even though both switches are connected via an 802.1Q trunk. Traffic for VLANs 10 and 20 passes without issues across the same trunk. The trunk is configured to allow all VLANs, and the allowed VLAN list explicitly includes VLAN 30. What is the most likely cause of the problem?

Exhibit: A switch interface connected to an IP phone and PC is configured as an access port in VLAN 10. The PC works, but the phone does not register. What additional configuration is most likely needed?

Two directly connected routers, R1 and R2, are configured with single-area OSPF in Area 0. The administrator notices that they are not forming a full OSPF neighbor adjacency. The exhibit displays relevant portions of the running configurations. What is the most likely cause of the problem?

A network engineer is troubleshooting intermittent connectivity on an access switch port connected to a server. The output of 'show interfaces gigabitEthernet 1/0/24' shows an increasing number of runts and giants, but no CRC errors. The 'show interfaces status' command indicates the port is in 'err-disabled' state every few hours and must be manually re-enabled. What is the most likely cause of this issue?

Exhibit: A client can ping 8.8.8.8 but cannot browse to www.example.com. Which service is most likely failing?

Based on the exhibit, what is the strongest explanation for why clients can browse by IP address but not by hostname?

A small office network uses a single public IP address on its router's WAN interface. The network administrator needs to allow all internal hosts to access the internet, but must also ensure that an internal web server with a private IP address is reachable from the internet. Which NAT configuration should the administrator implement to meet both requirements?

A host is physically connected to switch port Gi0/3. The technician runs 'show mac address-table' but does not find the host's MAC address for Gi0/3. The port status shows 'up/up', and the host was connected only a few minutes ago. What should the technician do next?

Refer to the exhibit. A network engineer is troubleshooting an OSPF adjacency issue between R1 and R2. The output of the show ip ospf neighbor command on R1 shows the neighbor relationship with R2 stuck in the EXSTART/DROTHER state. What is the most likely cause?

Exhibit: A script sends an API request and receives HTTP status code 401. What does that code indicate?

You are connected to R1 via console. R1 has three directly connected subnets: 192.168.1.0/24 (G0/0), 192.168.2.0/24 (G0/1), and 192.168.3.0/24 (G0/2). You need to configure a summary route to be advertised to a neighbor via a static route pointing to Null0 to prevent routing loops. The summary should cover all three subnets.

A branch router learns a route to 10.20.30.0/24 from OSPF with metric 30 and also has a static route to the same prefix with an administrative distance of 5. Which route will appear in the routing table?

Hosts in VLAN 10 need to communicate with hosts in VLAN 20. What is required for that communication to work?

A multilayer switch must route traffic between VLAN 10 and VLAN 20. Which condition is required for that to happen?

A network engineer is troubleshooting a link between two Cisco Catalyst 9300 switches that are connected via a 10GBASE-SR SFP+ module on each end over OM3 multimode fiber. The link is up, but the interface counters show a high number of CRC errors and runts. The engineer runs 'show interfaces Gi1/0/1' and 'show interfaces Gi1/0/1 transceiver details'. What is the most likely cause of the errors?

You are connected to R1 via console. The network consists of R1, R2, and a multilayer switch MLS1. R1's GigabitEthernet0/0 connects to MLS1's GigabitEthernet1/0/1 (VLAN 10), and MLS1's GigabitEthernet1/0/2 connects to R2's GigabitEthernet0/0. The goal is to enable IPv6 communication between R1 and R2 across the layer-3 switch. Currently, R1 and R2 cannot ping each other's IPv6 addresses. Configure R1's G0/0 with the IPv6 prefix 2001:db8:1:10::/64 using EUI-64, and R2's G0/0 with static IPv6 address 2001:db8:1:10::2/64. Also ensure MLS1 has IPv6 routing enabled and an IPv6 address on VLAN 10 (2001:db8:1:10::3/64). Troubleshoot and fix any layer-2 or layer-3 issues preventing connectivity.

You are connected to switch SW1. The network uses Rapid-PVST+ and SW1 has been accidentally configured with a low spanning-tree priority, causing it to become the root bridge for VLAN 10 even though it should not be. Additionally, an edge port connected to a server is repeatedly receiving BPDUs, causing it to go into err-disabled state. Configure SW1 so that it is never the root bridge for VLAN 10, and configure the edge port so that it automatically recovers from err-disabled state after 300 seconds. Finally, verify that SW1 is not the root bridge for VLAN 10.

Refer to the exhibit. A network administrator runs the show vlan brief command on SW2. Interface GigabitEthernet0/2 is intended to be an access port in VLAN 10, but it does not appear in the output. What is the most likely cause?

You are connected to R1 via the console. R1 is a new router that connects to three subnets: 192.168.1.0/24 (connected to GigabitEthernet0/0), 192.168.2.0/24 (connected to GigabitEthernet0/1), and 192.168.3.0/24 (connected to GigabitEthernet0/2). R1 must be able to ping the loopback0 interface of R2 (192.168.100.1/32) which is reachable via R2's Serial0/0/0 interface (10.0.0.2/30). The link between R1 and R2 is 10.0.0.0/30, with R1's interface being 10.0.0.1/30. No dynamic routing protocols are configured. Configure R1 to reach the loopback address of R2 using a host-specific static route (not a default route).

Which protocol is used to resolve a hostname such as www.example.com into an IP address?

Which two statements accurately describe DNS in normal network operation?

What problem does DHCP snooping help prevent?

You are connected to the console of R1. The network administrator reports that hosts in VLAN 10 cannot reach the server at 192.168.1.100. R1 is the default gateway for VLAN 10 via subinterface G0/0.10. The link between R1 and the switch SW1 appears to be up, but pings fail. Your task is to identify and resolve the issue.

Users on the inside network can browse the web, but the company now needs an internal web server at 192.168.10.50 to be reachable consistently from outside using one public IP address. Which design is most appropriate?

A show ip nat translations command displays this entry: Inside global 203.0.113.10:30001 Inside local 192.168.10.25:51514 Outside local 198.51.100.20:443 Outside global 198.51.100.20:443 Which statement is correct?

A network engineer is troubleshooting connectivity between two hosts in different VLANs on the same switch. Host A in VLAN 10 (10.10.10.5/24) cannot ping Host B in VLAN 20 (10.10.20.5/24). The switch is configured as a router-on-a-stick with a trunk port to an external router. The trunk port is up/up, but inter-VLAN routing fails. What is the most likely cause?

Which summary route best represents these four networks? 10.20.0.0/24 10.20.1.0/24 10.20.2.0/24 10.20.3.0/24

A user on a wireless guest network can associate successfully, obtains an IP address, but cannot reach the Internet. Which troubleshooting area should be examined first if the WLAN itself is working?

A DHCP client on VLAN 30 is not receiving an IP address from a DHCP server (10.99.99.20) on another subnet. The SVI for VLAN 30 is configured with an IP address and is up, but the DHCP relay command is missing. Which command should be added to the SVI configuration?

A network engineer must summarize the following routes before advertising them upstream: 172.16.32.0/24 172.16.33.0/24 172.16.34.0/24 172.16.35.0/24 Which summary route should be used?

Users on the inside network can browse the Internet through PAT, but an internal web server must now be reachable from outside on a predictable public IP. Which change best fits the requirement?

Which term describes a string or credential passed to an API to prove the client is allowed to access a resource?

On an 802.1Q trunk, which VLAN is sent untagged by default on many Cisco switches unless changed?

Which TWO statements correctly describe IPv4 and IPv6 host configuration?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to the ISP. GigabitEthernet0/1 (192.168.1.1/24) connects to the internal LAN. The network has an NTP server at 192.168.1.200. R1 must be configured as an NTP client to synchronize its time with the server. Additionally, R1 should serve as an NTP server for internal devices on the LAN with a stratum of 5 to maintain proper hierarchy. The time zone is UTC. No NTP configuration exists. Configure NTP on R1 as specified.

Which TWO statements about IPv4 and IPv6 ACLs are true?

A company wants a server on the inside network to be reachable consistently from outside using one known public IP address. Which NAT approach best fits that goal?

R1 learns three OSPF routes to different destinations: O 10.10.10.0/24 O IA 10.20.20.0/24 O E2 10.30.30.0/24 Which statement is correct about these route types?

A switch should disable an edge port immediately if a BPDU is received on it. Which feature is intended for that specific behavior?

A network administrator is troubleshooting a connectivity issue between two hosts on different subnets. The administrator captures packets on the source host and notices that the frames contain the correct source and destination MAC addresses but the encapsulated packets have incorrect source and destination IP addresses. According to the OSI model, which layer is most likely responsible for this issue?

A multilayer switch has working SVIs for VLAN 10 and VLAN 20, but traffic between the VLANs fails. Hosts can ping their own gateway interfaces. Which misconfiguration is most strongly suggested if the SVIs themselves are correct?

A wireless site reports that users can connect to the SSID, but performance drops sharply around the conference area whenever the room fills up. Based on the exhibit, what is the most likely cause?

Drag and drop the following steps into the correct order to describe the router's routing table lookup process for a destination IP address, including best-path selection using longest prefix match, administrative distance, and metric.

Exhibit: Users report that they can see the corporate SSID but fail authentication immediately after entering credentials. Guest wireless works on the same access point. Which issue is most likely?

Two switches are connected by a trunk. VLAN 50 exists on both switches, but traffic still fails across the link. The allowed VLAN list is correct. Which additional item should be checked next?

Drag and drop the following steps into the correct order to configure an LACP EtherChannel on two Cisco switches using active mode.

A network administrator is troubleshooting an issue where hosts on VLAN 10 cannot ping the default gateway at 192.168.10.1. The router (R1) has an SVI for VLAN 10 with IP 192.168.10.1/24. The administrator captures traffic on the router's G0/0/0 interface (trunk to the switch) and reviews the embedded packet capture output. What is the root cause of the problem?

You are connected to Multilayer Switch SW1. Configure LACP EtherChannel between SW1 and SW2 using ports GigabitEthernet0/1 and GigabitEthernet0/2. Ensure the channel is formed and active. The current configuration has mismatched VLAN assignments and speed/duplex settings preventing the channel from coming up. Verify the channel state using 'show etherchannel summary'.

A router interface is configured with 192.0.2.97/28. What is the network address of the subnet?

A router has a static route to 10.20.20.0/24 and also has a default route. Which route is used for traffic to 10.20.20.8?

You are connected to R1 via the console. Configure single-area OSPFv2 on R1 and R2 so that they form a full adjacency. The link between R1 and R2 uses 203.0.113.0/30. R1 has G0/0 203.0.113.1/30 and R2 has G0/0 203.0.113.2/30. R1's router-id must be 1.1.1.1, and R2's router-id must be 2.2.2.2. R1's GigabitEthernet0/0 interface is configured as a passive interface under OSPF, preventing OSPF hello messages from being sent out of that interface. Ensure that R1 does not send OSPF hellos out of its loopback0 interface (203.0.113.129/32). After configuration, verify the adjacency is established and OSPF routes are exchanged.

Which two statements accurately describe route summarization?

Refer to the exhibit. A network engineer notices that traffic from R1 to the 10.1.0.0/16 network is taking a longer path than expected despite OSPF being the only routing protocol. The engineer examines the OSPF LSDB on R1 to investigate. Based on the output, what is the most likely cause of the suboptimal routing?

A network engineer is automating the configuration of a new branch office router. The engineer needs a protocol that uses a YANG data model, supports both configuration and operational state retrieval, and operates over SSH for secure transport. Which protocol should the engineer use?

A user reports that the corporate SSID is visible and accepts the correct password, but the client always lands in a quarantined remediation network. Which troubleshooting area is strongest?

Why is administratively shutting down unused switch ports considered a useful hardening practice?

A user reports that websites can be opened by IP address but not by hostname. Which service is the strongest suspect?

Hosts on the inside network can reach the internet, but return traffic is failing after a new router was installed. The router's configuration shows that the LAN-facing interface has been configured with 'ip nat outside' and the WAN-facing interface with 'ip nat inside'. What configuration mistake is the most likely cause?

A host uses the subnet mask 255.255.255.240. How many usable host addresses exist in each subnet?

An enterprise network uses an IPv6 dual-stack design. Router R1 has a primary default route ::/0 via 2001:db8:1::1 with AD 1 and a floating default route with AD 10 via link-local address fe80::2. After the primary link fails, the floating route fails to install, and R1 loses all external connectivity. The administrator confirms the backup interface is up/up.

A network administrator needs to configure VLANs and access ports on 200 managed switches across multiple locations. The administrator requires a solution that uses a push‑based deployment model, does not require any agent software to be installed on the switches, and can be executed from a central control node. Which automation tool is most suitable for this task?

Refer to the exhibit. A network technician is troubleshooting router R1, which cannot reach hosts on the internet. R1 is connected to an ISP router at 203.0.113.1. The exhibit shows the output of the show ip route command. What is the most likely cause of the issue?

Dynamic ARP Inspection is most effective at preventing which attack?

An automation script must retrieve the current configuration state of a device from a REST API without modifying anything. Which HTTP method should it use?

A network administrator notices that file transfers to a server are extremely slow, and on the switch interface connecting to the server, the output of 'show interfaces' indicates a high number of runts and CRC errors, but no collisions. Which of the following is the most likely cause?

A router has this command configured: `ip nat inside source static 192.168.1.50 203.0.113.50`. What is the main effect of this configuration?

Which port-security violation mode drops frames from unauthorized MAC addresses but keeps the interface up and does not send an SNMP trap or syslog message?

R1 has routes to 172.16.10.0/24 from multiple sources. Which route will be installed?

Drag and drop the following steps into the correct order to configure a new WLAN on a Cisco WLC using IOS-XE CLI, including WPA3-Personal security, and to complete a wireless client association with DHCP.

Which two conditions must match on two switch ports before they can successfully form a Layer 2 EtherChannel? (Choose two.)

A network technician is troubleshooting a connectivity issue between two hosts. Host A sends a web request to Host B. The technician captures packets on the link between the two hosts and sees the data as '01010101...'. At which layer of the OSI model is this data being transmitted, and what is the correct PDU name for this layer?

Which three options are true regarding the operation of Dynamic ARP Inspection (DAI) on a Cisco switch? (Choose three.)

Which two statements accurately describe controller-based networking at the CCNA level?

Which option performs the RESTCONF operations correctly?

A user says the phone connected to a switch port works, but the attached PC does not get network access. What is the most likely switch-side issue?

A host uses subnet mask 255.255.255.224. How many total addresses exist in each subnet block?

Drag and drop the following steps into the correct order to describe the router's routing table lookup process from receiving a packet with a destination IP address to making the forwarding decision, including best-path selection criteria.

Which TWO statements correctly describe differences between 802.11ac (Wi-Fi 5) and 802.11ax (Wi-Fi 6)?

Drag and drop the following steps into the correct order to configure a WPA3 SSID on a Cisco WLC and complete a wireless client association.

Which TWO statements correctly describe the behavior of standard ACLs when applied to an interface?

Which data format is commonly used with REST APIs to represent objects, arrays, and key-value pairs?

A technician is troubleshooting an issue where internal hosts can successfully ping internet addresses but cannot establish HTTP sessions. The router is configured with PAT (overload) and uses an access list to define the inside local addresses. Recently, the internal network was renumbered from 192.168.0.0/24 to 10.0.0.0/24. What is the most likely cause?

A switch has a root port and an alternate port for the same VLAN. Which statement best explains the operational role of the alternate port?

An IPv6 host has a global unicast address and a correct default route learned from a router advertisement, but the next-hop entry shown on the host uses a link-local address rather than a global unicast address. What is the best explanation?

Based on the exhibit, why is the ACL not meeting the requirement to block only HTTPS traffic to the server?

Which statement correctly describes a feature of WPA3 security in wireless LANs?

A router shows the following routing table entries for the same destination: O 10.10.50.0/24 [110/20] via 192.168.12.2, GigabitEthernet0/0 D 10.10.50.0/24 [90/30720] via 192.168.13.2, GigabitEthernet0/1 Which route will become the active route in the routing table?

A trunk between two switches is up, but users in VLAN 40 cannot communicate across it. The output shows both sides allow VLAN 40. What is another likely trunk-related cause to check next?

You are connected to a multilayer switch MLS1. The network has two other switches SW1 and SW2 forming a triangle topology. Currently, SW1 is the root bridge but it should be SW2. Additionally, configure PortFast and BPDU Guard on interface GigabitEthernet0/2 of MLS1, which connects to a host. Simulate a BPDU violation on that port and then recover the port from err-disabled state.

You are connected to R1. The link between R1 and R2 is experiencing packet loss and slow performance. Examine the following partial show interface output: R1# show interfaces gigabitEthernet 0/0 GigabitEthernet0/0 is up, line protocol is up Duplex: Full, Speed: Auto, 100Mb/s Input errors: 12345, CRC: 5000, frame: 0, overrun: 0, ignored: 0 R2# show interfaces gigabitEthernet 0/0 GigabitEthernet0/0 is up, line protocol is up Duplex: Half, Speed: Auto, 100Mb/s Input errors: 0, CRC: 0, collisions: 5000, late collisions: 0 Identify the root cause of the issue, and apply the necessary fix on R1 to resolve the problem.

A static default route is configured on R1 toward ISP-A, and a second default route toward ISP-B is configured with a higher administrative distance. Which two statements are correct during normal operation and after ISP-A failure?

Drag and drop the following steps into the correct order to plan, configure, and apply an extended ACL that permits only HTTP traffic from the 192.168.1.0/24 network to the server at 10.0.0.100, and then verify the configuration.

Why is DHCP often preferred over manual addressing on larger user networks?

Exhibit: Users on SW2 in VLAN 30 can reach local devices but not hosts in VLAN 30 on SW1. What is the most likely reason?

A network administrator has several access points. All APs except one have successfully joined the wireless controller. The administrator verifies the failing AP’s IP address, subnet mask, and controller IP address are correctly configured. What is the most likely reason the AP cannot join the controller?

Which TWO statements correctly describe the configuration and verification of AAA with RADIUS/TACACS+ and 802.1X port-based authentication on IOS-XE?

Which three of the following are valid features of Enhanced Interior Gateway Routing Protocol (EIGRP)? (Choose three.)

Refer to the exhibit. A network engineer notices that a user connected to GigabitEthernet0/5 cannot access the network. The engineer issues the show port-security interface GigabitEthernet0/5 command. Based on the output, what is the most likely cause of the issue?

An engineer is comparing data serialization formats used by controllers and automation tools. Which two statements correctly describe JSON?

You are connected to R1, a router that must establish OSPFv3 adjacency with R2 over the directly connected link G0/0. The current configuration is incomplete: OSPFv3 process is configured but not enabled on the interface, and global IPv6 unicast routing is missing. Configure R1 so that it becomes an OSPFv3 neighbor with R2 and learns the loopback route 2001:db8:1:2::/64 via OSPFv3. Then verify neighbor state and routing table.

Exhibit: An OSPFv2 adjacency between two routers on Ethernet is not forming. Which two mismatches would directly prevent the routers from becoming neighbors?

Refer to the exhibit. A network administrator is troubleshooting an OSPF adjacency on R1's GigabitEthernet0/0 interface connected directly to R2. R2 is powered on and shows correct OSPF configuration, but the adjacency is stuck in the INIT or DOWN state. Based on the output, what is the most likely cause of the failure?

Drag and drop the following steps into the correct order to implement a basic network monitoring workflow using telemetry and streaming analytics on Cisco IOS-XE.

Drag and drop the following steps into the correct order to set up gRPC streaming telemetry subscription on a Cisco IOS-XE device.

A host has a valid IP address and subnet mask from DHCP but cannot reach remote networks because no gateway was provided. What is the best explanation?

You are connected to R1 via console. R1 is connected to three routers (R2, R3, R4) over Ethernet links, all in OSPF area 0. Due to network topology, R1 should not become the Designated Router (DR) or Backup Designated Router (BDR) on any of its interfaces. You need to configure R1's OSPF priority appropriately to ensure it never participates in DR/BDR elections.

An ACL on R1 contains only these entries: access-list 101 permit tcp 10.10.10.0 0.0.0.255 any eq 443 access-list 101 permit icmp any any What happens to an HTTP packet sourced from 10.10.10.25 and destined for 198.51.100.10 if ACL 101 is applied in the traffic path?

Drag and drop the following steps into the correct order to configure a Cisco switch as a DHCP relay agent with DHCP snooping, where the DHCP server is located on a remote router.

You are connected to R1 via console. R1 connects two networks: GigabitEthernet0/0 (10.0.0.1/30) to the ISP, and GigabitEthernet0/1 (172.16.1.1/24) to an internal network. The internal hosts (172.16.1.0/24) need to communicate with a server at 10.0.0.2 (ISP side) using a static NAT mapping. Configure static NAT so that internal host 172.16.1.100 is mapped to public IP 10.0.0.3 (which is not assigned to any interface; assume ISP routes 10.0.0.3 to R1). Also configure a static route to reach 10.0.0.3 via the ISP router (next-hop 10.0.0.2).

A network engineer notices that traffic from the router to server 192.168.10.5 is being sent over a slow backup link, even though the primary high-speed link is up. The routing table has an OSPF route for 192.168.10.0/24 via the primary link and a static host route to 192.168.10.5/32 via the backup link. Why is the backup link used for traffic to the server?

An OSPF-enabled router has two paths to the same destination network, and both paths have the same OSPF cost. What is the most likely default behavior?

Refer to the exhibit. An administrator has configured PAT for internal hosts to access the internet, but users report that they cannot reach external websites. The administrator suspects a NAT issue and runs the show ip nat statistics command. What is the most likely cause of the problem?

Which command output would be the best next step to verify whether the port-channel is operational after configuration changes?

An API call returns HTTP status code 401. What does that usually mean?

Exhibit: R1 has a default route pointing to 10.1.1.2. Users lose internet access when that next hop fails, even though a floating static backup exists. Why is the backup not installed?

A host with IP address 172.16.50.130 and mask 255.255.255.192 needs to reach 172.16.50.190. Which statement is correct?

Which TWO statements about fiber optic cables and SFP/SFP+ transceivers are correct?

A subnet must support at least 62 usable IPv4 host addresses. Which prefix is the most restrictive that meets the requirement?

A network administrator is configuring a new Windows 10 workstation on a network that uses DHCP. The workstation receives an IPv4 address of 169.254.10.20 with a subnet mask of 255.255.0.0 and no default gateway. The user cannot access the internet or other subnets. What is the most likely cause of this issue?

You are connected to SW1. Configure an LACP EtherChannel between SW1 and SW2 using ports GigabitEthernet0/1 and GigabitEthernet0/2. Set the channel-group mode to active on both sides. The port-channel interface should be configured as a trunk allowing VLANs 10, 20, and 30. Initially, the EtherChannel fails to form due to mismatched speed/duplex on one link. Identify and correct the issue, then verify the channel is up and operational.

Users can reach an internal server by IP address but not by hostname. What is the most likely cause?

R1 loses its route to 192.168.20.0/24 whenever R2's GigabitEthernet0/0 interface flaps. The network engineer has configured a floating static route with an administrative distance of 200. The OSPF route has an AD of 110. After R2's G0/0 interface recovers, the floating static route appears in the routing table instead of the OSPF route. What should the technician do next?

A network requires at least 500 usable host addresses in one IPv4 subnet. Which prefix is the smallest that meets the requirement?

An engineer is reviewing transport protocols for a new application. Which two characteristics are associated with TCP rather than UDP?

A packet is larger than the outgoing interface MTU and the DF bit is set in the IPv4 header. What should the router do?

You are connected to R1. Configure DHCP server on R1 to assign addresses from 192.168.50.0/24 to hosts on VLAN 50, excluding 192.168.50.1-192.168.50.20, with default-router 192.168.50.1 and DNS server 8.8.8.8. On switch SW1, configure DHCP snooping globally and on VLAN 50, and enable trusted ports on the uplink to R1. Then, a host on VLAN 50 reports it received an incorrect IP address; troubleshoot and fix the issue: the wrong helper-address is configured on SW1, the excluded range is too large, and a rogue DHCP server is present on port Fa0/5.

If a host has a valid IP address and subnet mask but no default gateway, what is the most likely result?

An AP broadcasts the correct SSID, but many clients on one floor experience poor performance while the same SSID works well on another floor. Which category of issue is most strongly suggested first?

Why might a controller return interface information as a JSON array instead of a single JSON object?

A host uses address 192.168.5.126/25. Which address is the broadcast address for its subnet?

A trunk is up between two switches, but traffic for VLAN 40 fails while other VLANs work. Which output item should be checked first?

An engineer wants a static route to be used only if the OSPF route to the same network disappears. What should be configured?

Users in a branch office can reach internal networks but cannot browse the Internet. The router has a correct default route and PAT is configured. Which missing item is the most likely cause if inside hosts are still using private source addresses on the WAN?

A client receives an IP address but cannot reach remote networks. Which DHCP option is most likely missing or incorrect?

A network automation script sends this HTTP request to a controller API: POST /api/v1/devices What does the POST method typically indicate in a RESTful API?

A company wants unauthorized devices plugged into unused wall ports to have as little chance of gaining access as possible. Which action most directly supports that goal?

A switchport connected to another switch is configured with `switchport mode dynamic auto` on both ends. What is the most likely outcome if neither side actively negotiates trunking?

Refer to the exhibit. A network engineer is troubleshooting an ACL that is not filtering traffic as expected. The engineer runs the show access-lists 110 command and notices that all access control entries (ACEs) show zero matches, even though traffic that should match the permit or deny statements is traversing the network. The engineer then checks the interface configuration. What is the most likely cause?

Why is administratively shutting down unused switch ports considered a useful hardening measure?

A non-root switch has two uplinks toward the root bridge. One path has a lower total STP cost than the other. What role will the lower-cost uplink have?

You are connected to R1 (192.0.2.1/24). Use RESTCONF to query the operational state of GigabitEthernet0/0 using the ietf-interfaces YANG module. Then, send a PATCH request to disable the interface (set 'enabled' to false) using the Cisco-IOS-XE-native YANG module. Identify the error when a PATCH request is sent with the wrong Content-Type header (application/json instead of application/yang-data+json) and when the PATCH URI uses an incorrect YANG path (ietf-interfaces instead of Cisco-IOS-XE-native).

Clients in VLAN 30 are not receiving addresses from the DHCP server located in VLAN 99. Which configuration change should be made on the Layer 3 interface for VLAN 30?

Drag and drop the route types on the left to the correct administrative distance and use case descriptions on the right.

You are connected to R1 via console. R1 is a new router connecting two subnets: 192.168.1.0/24 on G0/0 and 192.168.2.0/24 on G0/1. You need to configure IPv6 static routes so that hosts on these subnets can reach the IPv6 Internet via R2 (2001:db8:1::2). R1's G0/0 has IPv6 address 2001:db8:1::1/64, and R2 is the next-hop. Also configure a default IPv6 route toward R2.

Drag and drop the following steps into the correct order to configure PAT (Port Address Translation) on a Cisco IOS-XE router and describe the translation process for an outbound packet.

A subnet has the network address 192.168.20.128/26. What is the broadcast address?

Drag and drop the following steps into the correct order to configure BPDU Guard, Loop Guard, and Root Guard on a Cisco switch.

A host at 192.168.50.10/24 needs to send traffic to 192.168.60.20. Which MAC address will it normally place in the Ethernet destination field for the first frame?

Refer to the exhibit. A network engineer is troubleshooting a missing route on R1. The router R3 is configured to advertise network 192.168.30.0/24 via OSPF, but the route is not present in the OSPF routing table of R1 when issuing the show ip route ospf command. What is the most likely cause?

Refer to the exhibit. A network administrator is troubleshooting connectivity issues for hosts on VLAN 50 on SW1. The hosts on VLAN 50 cannot reach any devices outside SW1, even though the trunk link between SW1 and SW2 is up. The administrator issues the 'show interfaces GigabitEthernet0/1 trunk' command on SW1. Based on the output, what is the most likely cause of the issue?

You are connected to the console of SW1. The network administrator reports that a workstation connected to interface FastEthernet0/1 cannot communicate with the rest of the network. The workstation is configured for VLAN 10, but the interface is in VLAN 1.

Refer to the exhibit. An administrator is troubleshooting connectivity from a branch router R1 to the internet. A ping to 8.8.8.8 from R1 fails. The output of the show ip route command is shown. What is the most likely cause?

Why is SSH preferred over Telnet for remote device administration?

A branch LAN requires 50 usable IPv4 host addresses. What is the most efficient subnet mask that provides at least 50 usable hosts?

Two directly connected routers running OSPFv3 do not form an adjacency. Both interfaces have valid IPv6 addresses and can ping each other using link-local addresses. What is the most likely cause?

You are connected to R1. The link between R1 and R2 is down. The output of 'show interfaces gigabitEthernet0/0' on R1 shows: 'GigabitEthernet0/0 is administratively down, line protocol is down (disabled)', with IP address 203.0.113.1/30, MTU 1500, and no input/output errors. Determine the root cause and configure the necessary fix to bring the interface up and restore connectivity.

You are connected to R1 via console. Configure OSPFv3 for IPv6 on R1 and R2 so that IPv6 loopback interfaces on both routers can communicate. R1's GigabitEthernet0/0 and R2's GigabitEthernet0/1 are directly connected. Ensure OSPFv3 is enabled on the correct interfaces and verify neighbors and routes.

A switch port connected to an end host is configured with both PortFast and BPDU Guard. What is the most likely outcome if a small switch is connected there and starts sending BPDUs?

Match each trunking or switchport term to its most accurate description.

A host is configured with 10.1.1.34/30. Which address is the broadcast address for its subnet?

A network technician connects a new Cisco switch to an existing access switch using a Category 5e copper patch cable. The link fails to come up, and the interface status shows 'err-disabled'. The technician checks the interface diagnostics and the running configuration. What action should the technician take to resolve the problem?

Which term refers to a lightweight data-interchange format that is easy for humans to read and write, and easy for machines to parse and generate?

A network engineer is troubleshooting a link between two Cisco Catalyst 9300 switches that are connected via a single-mode fiber optic cable. The link is up, but the interface counters show a high number of CRC errors and frame check sequence (FCS) errors. The interface is configured for 1000 Mbps and full duplex on both ends. What is the most likely cause of these errors?

Which two statements accurately describe common uses of NTP in network operations?

Which TWO statements about SFP transceivers and fiber optic cabling are correct?

You are connected to R1 via the console. R1 has two directly connected interfaces: G0/0 to R2 (IPv4 only) and G0/1 to a LAN switch (dual stack). Your task: configure IPv4 and IPv6 default routes on R1 pointing to R2 (next-hop 10.0.0.2 and 2001:db8:1::2). Also configure a floating static route to 192.0.2.0/24 via R2 with an administrative distance of 10 (so it is used only if the directly connected route fails). The current running-config shows an incorrect static route that causes recursive routing failure. Identify and fix the issue.

You are connected to R1 via the console. R1 is a Cisco ISR 4321 router running IOS-XE. The network manager wants to monitor interface utilization changes. Use RESTCONF to retrieve the operational state of GigabitEthernet0/0/0 on R1. The device has RESTCONF enabled with username 'admin' and password 'cisco'. The management IP is 192.168.1.1.

Refer to the exhibit. A network administrator connects an IP phone to interface GigabitEthernet1/0/1 on a Cisco Catalyst switch. The PC connected through the phone works normally on the data VLAN, but the phone cannot obtain an IP address and fails to register with the call server. Which action will resolve the problem?

A user reports that they cannot access the company's internal web server at 'intranet.company.local' from their workstation. The workstation can ping the web server's IP address 192.168.10.50 successfully, and other internal services like email (mail.company.local) are reachable. Which DNS record issue is most likely causing this problem?

A network engineer notices that an uplink port on a distribution switch has moved to a root-inconsistent state and is blocking traffic. The port is configured with Root Guard and is connected to a new access switch. The new access switch has a lower bridge priority than the current root bridge. What is the most likely cause?

A PC connected to switch port Gi0/10 should be in VLAN 20 but receives broadcasts only from VLAN 1. Which switchport setting is most likely wrong?

After connecting a new switch to interface GigabitEthernet1/0/1 on a distribution switch, a network engineer notices that the interface is in err-disable state. The engineer checks the configuration and finds that spanning-tree portfast and spanning-tree bpduguard enable are applied to the interface. What is the most likely cause of the err-disable state?

A switch displays this output: Port Name Status Vlan Fa0/1 connected 10 Fa0/2 connected 10 Fa0/24 connected trunk Which port should be checked first if a user in VLAN 20 cannot reach the distribution switch over the uplink?

A branch router should automatically learn the IP address of a time source so logs from all devices show matching timestamps. Which service provides that function?

A switch should automatically disable any access port that receives a BPDU from an attached device. Which feature directly provides that behavior?

Match each basic automation term to its most accurate meaning.

Which TWO statements correctly describe the OSI model layers and their corresponding PDU names during encapsulation?

You are connected to R1. The inside network 192.168.1.0/24 must be able to access the internet using PAT (NAT overload) with the outside interface G0/1 IP 203.0.113.1. Additionally, the internal server at 192.168.1.10 must be reachable from the internet via static NAT to 203.0.113.10. The current configuration is incomplete and contains errors. Identify and fix all issues so that both PAT and static NAT work correctly.

A switch trunk is carrying several VLANs, but VLAN 99 traffic is failing. The trunk allowed list includes VLAN 99 on both sides. Which statement best explains why a VLAN can still fail even when it is allowed?

You are connected to a multilayer switch MLS1. Configure a static default route for IPv4 that points to next-hop 192.0.2.2, but also configure a floating static default route with an administrative distance of 10 that uses next-hop 198.51.100.2. Additionally, configure a static host route for IPv6 host 2001:db8:1::10/128 via next-hop 2001:db8:1::1. The current configuration has a recursive routing failure for the IPv4 default route because the next-hop 192.0.2.2 is not reachable; you must first fix that by adding a directly connected static route. Ensure the floating route becomes active only when the primary route fails.

An administrator wants to permit HTTP and HTTPS from 10.1.10.0/24 to a web server at 198.51.100.20 and deny everything else from that subnet. Which ACL type is required?

You are connected to R1. Configure R1 as a DHCP server for VLAN 20 clients (192.168.20.0/24) with DNS server 203.0.113.10 and default gateway 192.168.20.1. On switch SW1, enable DHCP snooping globally and on VLAN 20, configure the uplink to R1 as trusted, and ensure that the DHCP server is reachable via ip helper-address on the VLAN 20 SVI. Currently, clients are not receiving IP addresses because of misconfigurations: the excluded-address range on R1 is too large (excluding the entire subnet), the helper-address on SW1 points to a wrong IP (192.0.2.99), and a rogue DHCP server is connected to port Fa0/3 on SW1. Fix all issues so that clients can get addresses securely.

A host is configured as 172.16.20.190/26. Which range contains the usable host addresses for that subnet?

You are connected to SW1. The network has three switches (SW1, SW2, SW3) running Rapid-PVST+. SW1 should be the root bridge for VLAN 10. PortFast and BPDU Guard must be enabled on all edge ports connected to end hosts. An err-disabled port (G0/1) has occurred due to a BPDU violation on an edge port. Recover the port and ensure it is configured correctly to prevent recurrence.

Drag and drop the following steps into the correct order to interpret packet capture output for L2/L3 troubleshooting.

Which three statements accurately describe the role of Cisco's AI-powered security features (such as Cisco AI Network Analytics, Stealthwatch, or DNA Center's AI-Enhanced Analytics) in network security operations? (Choose three.)

A router has the following routes in its routing table: a static route to 10.60.4.16/28, an OSPF route to 10.60.4.0/24, and an EIGRP route to 10.60.0.0/16. Which route will be used for a packet destined to 10.60.4.17?

A network operations team is implementing an automated system to detect and remediate interface flapping on core switches. The system must be able to query the network device for interface status and execute commands to disable or reconfigure the interface if a pattern of flapping is detected. Which protocol or technology enables the system to programmatically interact with the network device for both monitoring and configuration changes?

A switch port connected to a user PC is configured as a trunk. The PC cannot communicate normally. What is the best explanation?

A host is assigned 192.168.10.33/28. Which subnet contains that host?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to R2 (10.0.0.2/30). Hosts on the LAN (192.168.1.0/24) need DHCP services. The DHCP server is located at 172.16.1.100 on a different subnet reachable via R2. Configure R1 to forward DHCP broadcasts to the DHCP server.

An operations team wants a monitoring platform to periodically read interface counters and CPU statistics from routers. Which technology is most closely associated with that requirement?

You are connected to R1. The network team reports intermittent connectivity between R1 and R2. Examine the following `show interface` output from R1 to identify the root cause of the issue. Then apply the necessary configuration commands on R1 to resolve the problem. GigabitEthernet0/0 is up, line protocol is up Internet address is 10.0.0.1/30 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 100 packets input, 8000 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 100 input errors, 100 CRC, 0 frame, 0 overrun, 0 ignored 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out

A network technician is troubleshooting a router that cannot be accessed via SSH. The router responds to Telnet but SSH attempts return 'connection refused'. The technician confirmed that 'ip ssh version 2' is configured and 'show ip ssh' indicates SSH is enabled. The output of 'show line vty 0 4' shows 'transport input telnet'. What should the technician do next?

Which option correctly matches an IP service symptom to the most likely service involved?

A subnet has the network address 192.168.30.0/26. What is the broadcast address?

You are connected to SW1 via the console. The network has three switches connected in a triangle: SW1 (G0/1 to SW2 G0/1), SW1 (G0/2 to SW3 G0/1), and SW2 (G0/2 to SW3 G0/2). SW1 is the root bridge. A PC is connected to SW3's G0/3 port, which should be an edge port. However, the PC has been sending BPDUs, causing the port to go err-disabled. Configure SW3 to prevent this in the future: enable PortFast and BPDU Guard on G0/3. Then, verify that the port recovers from err-disabled state and that a specific blocked port on SW2 is identified. Use the provided show output to determine the current state and necessary commands.

You are connected to R1. Configure IPv4 and IPv6 static routes, default routes, and floating static routes so that R1 can reach the Internet via R2 (IPv4 and IPv6). The primary route to the Internet should use next-hop 203.0.113.2 (IPv4) and 2001:db8:203:0:113::2 (IPv6). A backup floating static route with administrative distance 200 must exist for IPv4 only, using next-hop 198.51.100.2. Ensure the default routes are correctly configured and troubleshoot any recursive routing failure. Note: R1 currently has an incorrect IPv6 default route pointing to 2001:db8:198:51:100::2 that must be removed.

A controller-based WLAN is deployed across multiple floors. Users can associate to the SSID on both floors, but their experience improves when moving between APs compared with a poorly designed standalone deployment. Which wireless concept is most closely related to that client movement experience?

A network administrator is troubleshooting connectivity from a PC (192.168.1.10/24) to a server at 10.0.0.5/24. The PC's default gateway is 192.168.1.1. Router R1 has a directly connected route to 10.0.0.0/24 via interface GigabitEthernet0/1, which is connected to another VLAN. The server is actually located on the 10.0.0.0/16 network, reachable via a static route through 192.168.1.2. What is the most likely cause of the connectivity issue?

You are troubleshooting connectivity for a wireless client connected to the home network shown below. The client has obtained an APIPA address (169.254.x.x), indicating DHCP failure. Verify the DHCP server configuration on R1 and correct the issue so that the client receives a valid IP address from the 192.168.1.0/24 subnet.

You are troubleshooting a link between R1 (G0/0) and R2 (G0/0). The link is up but experiencing packet loss. You suspect an interface speed/duplex mismatch or SFP issue. Configure R1's interface to match the correct speed and duplex, and replace the SFP module if necessary to support a required distance of 40 km over single-mode fiber.

Which two statements correctly describe a RESTful API used by network controllers? Choose two.

Match each networking concept to its most accurate role.

A network engineer configures OSPF between R1 and R2, but the routers never become neighbors on GigabitEthernet0/0. Based on the exhibit, what is the most likely cause?

A network team wants an ACL that permits HTTPS from 10.1.50.0/24 to a web server at 203.0.113.10 and denies all Telnet traffic from that subnet to any destination. Which two ACEs are required?

A router has a static route and a RIP route for the same destination prefix. What is the primary reason the static route is preferred over the RIP route?

You are connected to R1, a multilayer switch acting as an HSRP active gateway for VLAN 100. The network requires R1 to be the active router with a virtual IP of 192.168.100.1. Currently, both R1 and the peer router R2 show as active in 'show standby brief', and the virtual IP is misconfigured. Configure HSRP on R1 to fix these issues: set priority to 110, enable preempt, correct the virtual IP, and track interface GigabitEthernet0/1 (decrement priority by 20 if it goes down).

After configuring a static discard route with the command 'ip route 0.0.0.0 0.0.0.0 Null0 254' on R1, a network engineer finds that traffic to destinations that are not in the routing table is still being forwarded out to the ISP instead of being dropped. What is the most likely cause?

A router is configured with PAT for inside users. Which symptom most strongly suggests the NAT inside/outside roles are reversed on the interfaces?

Which VLAN is used by default for most switch ports on a new Cisco switch?

You are connected to R1 via console. R1 is a router that should restrict SSH access to only the management station at 192.168.1.100. Currently, SSH is enabled but any IP can connect. Configure a standard named ACL called 'SSH_ACL' to permit only the management station, and apply it to the VTY lines to filter incoming SSH connections. Ensure the VTY lines use SSH only (no Telnet). The SSH version should be set to 2.

You are troubleshooting a network connectivity issue on R1. The network 192.168.10.0/24 behind R2 must be reachable from R1 via the primary path through R2 (192.0.2.2). A backup path via R3 (198.51.100.2) should automatically take over if the primary fails. Currently, traffic to 192.168.10.0/24 is incorrectly using the backup path even though the primary path is operational. Analyze the routing table and configuration, then fix the issue so that the primary path is preferred when available.

A switch port connected to a workstation is configured with sticky MAC learning and a maximum secure MAC count of 1. What is the main operational benefit of sticky learning in this case?

You are connected to R1. The network uses private IP 10.10.10.0/24 on the inside and must reach the Internet via the outside interface G0/1 with public IP 203.0.113.1/29. Configure PAT (NAT overload) so that inside hosts can access the Internet, and also configure a static NAT for the internal server 10.10.10.100 to public IP 203.0.113.2. The current configuration has errors: the inside and outside interfaces are swapped, the ACL is incorrectly defined, and the overload keyword is missing. Fix all issues.

A network engineer is troubleshooting a link between two Cisco switches that are connected via a 1000BASE-LX SFP transceiver. Hosts on VLAN 10 on Switch A cannot ping the default gateway on Switch B. The interface on Switch A is up, but the engineer notices CRC errors incrementing. What should the engineer do to resolve this issue?

Which TWO statements accurately describe wireless LAN fundamentals for CCNA 200-301 v2.0? (Choose two.)

Which two statements accurately describe why BGP is often relevant at an Internet or multi-provider edge?

Which TWO commands are required to configure a switch port to support both a desktop PC and a VoIP phone using voice VLAN?

A router has routes to 172.20.0.0/16, 172.20.10.0/24, and 172.20.10.64/26. Which route is used for traffic to 172.20.10.70?

Drag and drop the following steps into the correct order to sequence the TCP three-way handshake between a client and a server.

You are connected to R1. R1 has OSPF configured on GigabitEthernet0/0 with network 10.0.0.0 0.0.0.3 area 1, ip ospf hello-interval 10, and ip ospf dead-interval 40. R2 has OSPF configured on its GigabitEthernet0/0 with network 10.0.0.0 0.0.0.3 area 0, ip ospf hello-interval 5, and ip ospf dead-interval 20. Correct these mismatches so that R1 and R2 become OSPF neighbors.

Which TWO statements about fiber optic cable types and SFP transceivers are correct?

A host is configured as 192.168.100.65/26. What is the valid host range for its subnet?

Which two statements accurately describe UDP compared with TCP?

A network administrator is configuring a Layer 2 EtherChannel between two switches. Switch A uses 'channel-group 1 mode active', and Switch B uses 'channel-group 1 mode desirable'. All member interfaces are trunk ports with identical allowed VLANs. The EtherChannel fails to form. What is the most likely cause?

Which four of the following are true statements regarding the operation of DHCP snooping on a Cisco switch? (Choose all that apply. There are four correct answers.)

What problem do first-hop redundancy protocols such as HSRP solve?

A router has routes for 10.10.0.0/16, 10.10.20.0/24, and a default route. Which route is used for destination 10.10.20.55?

A router has a static route to 10.30.5.128/25, an OSPF route to 10.30.5.0/24, and a default route 0.0.0.0/0 in its routing table. Which route will the router use for destination 10.30.5.130?

Which wireless design objective is achieved by using nonoverlapping channels in adjacent cells?

You are connected to SW1. The current configurations of interfaces GigabitEthernet0/1 and GigabitEthernet0/2 are as follows: Gi0/1: speed 100, duplex half, switchport access vlan 10 Gi0/2: speed 1000, duplex full, switchport access vlan 20 The port-channel interface 1 does not exist. Configure a LACP EtherChannel between SW1 and SW2 using these two interfaces, with port-channel 1 and mode active on both sides. Ensure the channel forms by resolving any speed/duplex or VLAN mismatches. After configuration, verify with 'show etherchannel summary'.

You are connected to R1 via the console. The link between R1 and R2 is experiencing intermittent connectivity. A 'show interfaces GigabitEthernet0/0' output shows the interface is up/up, line protocol up, Full-duplex, 1000Mb/s, but there are 1234 input errors, including 567 CRC errors. Identify the root cause of the issue, and apply the necessary configuration fix to restore full connectivity.

Drag and drop the following steps into the correct order to capture and analyze traffic for L2/L3 troubleshooting.

You are connected to R1, a router that must send SNMP traps to a management server at 203.0.113.10 and export NetFlow data to a collector at 203.0.113.20. Currently, SNMPv2c traps are not being sent, and SNMPv3 is not configured for read-only access with authentication and privacy. Additionally, NetFlow export is missing the destination and version configuration. Configure the necessary commands on R1 to enable SNMPv2c traps (community string 'public'), configure SNMPv3 user 'admin' with SHA authentication and AES 128 encryption (password 'cisco123' for both auth and priv), and set NetFlow export to version 9.

A subnet must support 14 usable hosts. Which prefix is the smallest that meets the requirement?

You are connected to a multilayer switch MLSW1. PortFast and BPDU Guard have already been enabled on interface GigabitEthernet0/1, which connects to an end device, and a BPDU received on that interface placed it in the err-disabled state. Configure Rapid PVST+ so that MLSW1 becomes the root bridge for VLAN 10 with a priority of 4096. Recover the interface by re-enabling it. Finally, verify which port is blocking on VLAN 10 by connecting to MLSW2 and executing the appropriate show command.

Refer to the exhibit. An administrator notices that all interfaces on R1 are in an administratively down state. The administrator issues the show version command and sees the following output. What is the most likely cause of the issue?

You are connected to SW1 via console. SW1 is a multilayer switch with SVIs for VLAN 10 (192.168.10.1/24) and VLAN 20 (192.168.20.1/24). Hosts in VLAN 10 and VLAN 20 need to communicate with each other. Currently, inter-VLAN routing is not working. You need to enable routing on SW1 and verify that the SVIs are operational.

Exhibit: Users on the inside network can open connections to a web server in the DMZ, but return traffic is denied by an ACL on the outside interface. Which statement best explains the issue?

Refer to the exhibit. A network engineer notices that on a four-link EtherChannel bundle between two switches, all traffic from a particular VLAN is being forwarded over only one physical link, while the other three links remain idle. The engineer suspects a load-balancing issue and issues the show etherchannel load-balance command, the output of which is shown. What is the most likely cause of the uneven traffic distribution?

In AAA, which function determines what an authenticated user is allowed to do after login?

Which TWO statements correctly describe the encapsulation and de-encapsulation process at the transport layer of the OSI model?

A switchport connected to another switch is configured as an access port by mistake. Which symptom is most likely in a multi-VLAN design?

After enabling DHCP snooping on VLAN 10, a technician finds that clients in that VLAN are no longer receiving IP addresses from the DHCP server. The server is connected to port Gi0/24. What is the most likely cause?

You are connected to SW1, a multilayer switch. Configure DHCP snooping and an IP helper-address so that clients in VLAN 20 receive IP addresses from the DHCP server at 10.0.0.2. The DHCP server is already configured with a pool for 192.168.20.0/24, but clients are not getting addresses. Identify and correct the issues in the current configuration.

Which TWO statements are true about configuring and verifying VLANs, 802.1Q trunking, native VLAN, and inter-VLAN routing with router-on-a-stick?

A network engineer is troubleshooting a wireless performance issue in a dense office environment. Clients on the 5 GHz band are experiencing low throughput even though they are close to the AP. The AP is a Cisco 9130AXI running IOS-XE 17.9. What is the most likely cause of the poor performance?

Why might an automation script prefer a token-based API session over repeatedly prompting a human operator for credentials?

A user joins the employee SSID successfully and can browse internal resources, but VoIP over Wi-Fi calls fail only while roaming between floors. Which troubleshooting area is the strongest first focus?

Which TWO statements are true about OSPFv2 neighbor adjacency, network statements, and passive interfaces?

Refer to the exhibit. An engineer expects all traffic destined to the 10.10.10.0 network to be forwarded via 10.1.1.2. However, when testing connectivity to host 10.10.10.64, traffic is being sent to 10.2.2.2 instead. What is the most likely cause?

A router learns 172.16.40.0/24 from OSPF with AD 110 and metric 20. It also learns the same prefix from EIGRP with AD 90 and feasible distance 30720. Which route is installed?

Why is PortFast typically enabled on switch ports connected to end devices?

A network administrator connects an IP phone to interface Gi0/1 and a PC to the phone's PC port. Users report that the phone cannot register with the call manager and the PC does not obtain an IP address. The administrator verifies the configuration shown in the exhibit. What is the most likely cause of the problem?

Which TWO statements correctly describe NTP stratum levels and syslog severity levels in a Cisco IOS-XE environment?

A network team wants to collect flow-level traffic statistics from routers to identify top talkers and bandwidth consumers. Which two statements about NetFlow are correct?

Drag and drop the following steps into the correct order to configure a Layer 3 switch to perform DHCP relay agent and DHCP snooping for a remote DHCP server.

Drag and drop the following steps into the correct order to capture and analyze traffic on IOS-XE using the embedded packet capture feature, and in Wireshark to isolate a Layer 2 or Layer 3 fault.

Which protocol is preferred over Telnet for remote CLI management because it encrypts the session?

A network administrator is troubleshooting a Windows 10 client that cannot reach the internet. The client is connected to a Cisco switch port configured as an access port in VLAN 100. The administrator runs ipconfig on the client and sees an IP address of 169.254.10.15 with a subnet mask of 255.255.0.0. The switch port shows status up/up. What is the most likely cause of the issue?

A router interface is configured for OSPF, but neighbors do not form. The engineer checks the interface and sees Hello 10 and Dead 40. The neighbor on the same segment uses Hello 30 and Dead 120. What is the most likely cause of the OSPF adjacency failure?

A router has these routes installed. Which path will be chosen for traffic to 172.16.10.200?

Why is route summarization useful at a distribution layer or area boundary?

Which three statements accurately describe the role of AI in software-defined networking (SDN) and intent-based networking (IBN)? (Choose three.)

A static default route is configured with an administrative distance of 250. What is the most likely design intention?

A switch port connected to an IP phone and a PC should separate voice traffic from data traffic while still using one physical edge connection. Which feature best supports that design?

You are connected to R1 via the console. Configure single-area OSPFv2 on R1, R2, and R3 so that all three routers can exchange routes. The current configuration has mismatched hello/dead timers on the link between R1 and R2, and an area mismatch on the link between R2 and R3. Correct these issues and ensure OSPF adjacencies form.

Which two statements accurately describe passive interfaces in OSPF?

A PC in VLAN 30 must obtain an address from a DHCP server in VLAN 99. Which feature is required on the Layer 3 interface for VLAN 30?

Which TWO of the following are essential IPv4 host parameters that must be correctly configured for a host to communicate with devices on remote networks?

A network administrator is troubleshooting connectivity between two directly connected Cisco switches. Hosts on VLAN 10 connected to Switch A cannot ping the default gateway on Switch B. The interface on Switch A shows 'up/up' but there are excessive CRC errors and runts. The administrator checks the interface configuration on both switches. What is the most likely cause of the issue?

Exhibit: R3 learns 10.50.0.0/16 by OSPF through two equal-cost paths. What will R3 do by default?

A branch router uses PPP on a serial WAN link. Which additional PPP capability most directly improves access security on that link?

Which cable type is commonly used to connect a switch to a router when using standard Ethernet interfaces on modern devices with auto-MDIX support?

Drag and drop the following steps into the correct order to capture and analyze traffic on IOS-XE using the embedded packet capture feature, and in Wireshark to isolate a Layer 2 or Layer 3 fault.

Which TWO statements are true regarding HSRP active/standby election, priority, and preemption?

Match each basic networking service to its most accurate role.

A branch office uses PAT overload on the edge router. Inside users can reach the internet, but return traffic for a newly deployed server must be mapped to a specific inside host. Which two statements are correct?

You are connected to the console of R1, a Cisco IOS-XE router. The network operations team needs to automate the backup of the running configuration to a TFTP server using a Python netmiko script. However, the script is failing. Your task is to write the correct netmiko commands to connect to R1 and save the configuration to the TFTP server at 192.168.1.100.

A host with address 192.168.1.130/26 needs to identify its local subnet. Which subnet does it belong to?

A user can reach a remote web server by IP address but not by hostname. Which service should be checked first?

An administrator configures an EtherChannel between SW1 and SW2. The port-channel interfaces are physically up, but the EtherChannel bundle fails to come up. On SW1, the channel-group is set to mode active; on SW2, it is set to mode on. What is the most likely cause?

A network technician is troubleshooting a connectivity issue between two directly connected switches, SW1 and SW2. Hosts on VLAN 10 connected to SW1 can ping each other but cannot ping the default gateway or any host on VLAN 10 connected to SW2. The interface on SW1 is up/up, but the interface on SW2 is up/down. What is the most likely cause of the problem?

Two switches are connected by a trunk. VLAN 50 exists on both switches, but hosts in VLAN 50 cannot communicate across the link. All other VLANs work. Based on the exhibit, what is the most likely cause?

A router has a default route and a specific route to 203.0.113.0/24. Which route is used for traffic to 203.0.113.25?

You are connected to SW1 via the console. SW1 is a Layer 2 switch connected to router R1 via trunk port G0/1. The trunk is currently using VLAN 1 as native VLAN, but the network administrator wants to change the native VLAN to VLAN 99 for security. Configure the trunk on G0/1 to use native VLAN 99 and verify.

Refer to the exhibit. Users on the inside network can browse the web, but return traffic is failing for some sessions. A partial configuration shows: interface GigabitEthernet0/0 ip address 192.168.10.1 255.255.255.0 ip nat outside ! interface GigabitEthernet0/1 ip address 203.0.113.10 255.255.255.0 ip nat inside ! ip nat inside source list 1 interface GigabitEthernet0/1 overload access-list 1 permit 192.168.10.0 0.0.0.255 Based on this configuration, which change is required to make PAT work correctly?

A network engineer needs a floating static route to back up an OSPF-learned route. Which two configurations are necessary for the static route to remain unused until OSPF fails?

You are connected to R1, a multilayer switch acting as the STP root for VLAN 10. Configure Root Guard on port GigabitEthernet0/1 (designated port) to protect against superior BPDUs from an unauthorized switch, Loop Guard on uplink GigabitEthernet0/2 to prevent forwarding loops on unidirectional links, and BPDU Guard on PortFast-enabled GigabitEthernet0/3 to shut down the port if a BPDU is received. After configuration, troubleshoot the scenario: a superior BPDU is received on G0/1, causing it to be blocked by Root Guard, and an unauthorized switch sends a BPDU to G0/3, placing it in err-disable state. Verify the final configuration and state.

Exhibit: A host has address 192.168.14.77/27. Which address is its valid default gateway if the first usable address in the subnet is chosen for the router interface?

A network administrator notices that a workstation connected to a Cisco switch port cannot communicate with other devices on the same VLAN. The switch port is up/up, but the workstation reports slow performance and intermittent connectivity. What is the most likely cause of this issue?

A host address is 2001:db8:100:20::25/64. Which portion identifies the network prefix?

Drag and drop the following steps into the correct order to troubleshoot a link-down issue on a GigabitEthernet interface using an SFP transceiver.

Which four of the following are characteristics or functions of a stateless firewall, such as an extended access control list (ACL) on a Cisco router? (Choose four.)

A host on a guest WLAN can browse the Internet but cannot reach internal corporate resources, while employees on another SSID can. Which statement best explains why that can be a correct design outcome?

Exhibit: A branch router receives time from an NTP server, but the show output marks the server with a tilde instead of an asterisk. What does that mean?

A company wants private IPv4 addressing that can be routed internally but not on the public Internet. Which range meets that requirement?

A network administrator has configured 802.1X port-based authentication on a Cisco IOS-XE switch port connected to a single PC. The port is in the 'authorized' state, but the PC cannot reach any network resources beyond its directly connected switch. The switch is configured to use RADIUS for authentication. What is the most likely cause of this issue?

Drag and drop the items on the left to the correct descriptions on the right.

Exhibit: R1 has learned 10.50.0.0/24 through OSPF and also has a floating static route to the same prefix with administrative distance 130. Which route is installed while OSPF is healthy?

Why is Telnet generally discouraged for network device administration?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (192.168.1.1/24) connects to the management network, and GigabitEthernet0/1 (10.0.0.1/30) connects to the core. You need to restrict SSH access to R1 from only the management subnet 192.168.1.0/24. Additionally, SSH should be configured with a domain name 'example.com' and a modulus of 2048 bits. The username 'admin' with password 'Cisco123' should be created for SSH login.

You are troubleshooting DNS resolution issues from R1. Using nslookup and dig commands, diagnose why the router cannot resolve the hostname 'fileserver.courseiva.com' to an IP address, and why reverse lookup for IP address 198.51.100.10 fails. Determine the appropriate fix to ensure successful forward and reverse DNS resolution.

You are connected to SW1 via the console. The network uses VLANs 10 (Sales) and 20 (Engineering). A new switch SW2 is connected to SW1 via G0/1. You need to enable CDP to discover neighbor devices and verify that SW1 sees SW2. Currently, CDP is disabled globally.

Which three of the following are characteristics of Layer 2 Ethernet switches that support VLANs? (Choose three.)

A branch office uses PAT for user Internet access. The administrator notices that inside users can browse out, but an internal server still cannot be reached consistently from outside. Which change is most appropriate?

Why is shutting down unused switch ports considered a useful hardening measure?

Select the options that correctly pair the security principle or control with its meaning.

Refer to the exhibit. A network engineer is troubleshooting a serial link between two routers that is not coming up. The engineer issues the show controllers command on one router and sees the output shown. What is the most likely cause of the issue?

A network administrator has recently upgraded the corporate wireless LAN to support 802.11ax (Wi-Fi 6) and is using WPA3-Enterprise with a central WLC. Several users with new 802.11ax laptops report that they can connect to the SSID, but after a few minutes their connections drop and then re-establish, while legacy 802.11ac clients work without issues. Which action will resolve this problem?

Drag and drop the following steps into the correct order to configure HSRP on a Cisco IOS-XE router, including priority, preempt, virtual IP, and then verify the active/standby election and failover process.

Which two statements correctly describe JSON?

Which of the following is the correct order to plan, configure, and apply an extended ACL that blocks Telnet traffic from the 192.168.1.0/24 network to the 10.0.0.0/24 network, applied inbound on the router's G0/0 interface?

Which three of the following are security best practices for implementing AAA on a Cisco router? (Choose three.)

Which two statements accurately describe floating static routes?

Two routers are in the same OSPF area and on the same subnet, but they do not form an adjacency. One interface uses a hello interval of 10 seconds and the other uses 5 seconds. What is the most likely cause?

You are connected to R1, a Catalyst 3650 multilayer switch running IOS-XE. Configure Root Guard on all designated ports, Loop Guard on uplink interfaces, and BPDU Guard on all PortFast-enabled ports. Troubleshoot the current issue: one port is receiving a superior BPDU and is being blocked by Root Guard, and a different PortFast port has gone err-disabled after BPDU Guard triggered. Verify that Root Guard is active on port Gi1/0/1, Loop Guard is active on Gi1/0/2, and BPDU Guard is enabled on Gi1/0/3.

Drag and drop the following steps into the correct order to install a new fiber optic cable and SFP module on a Cisco switch, then verify the interface status.

Drag and drop the following steps into the correct order to configure a switch port for a VoIP phone (voice VLAN + data VLAN), an AP trunk, and a PoE-powered IoT device.

Which two statements accurately describe good management-plane security practice on network devices?

A switch shows this output from the "show interfaces trunk" command: Gi0/1 on 802.1q trunking 1 Gi0/2 auto 802.1q not-trunking 1 Which statement is correct?

A branch router is running single-area OSPF. An engineer wants an interface to advertise its connected network into OSPF but must prevent hello packets from being sent on that LAN segment. Which two actions achieve that goal?

Exhibit: A static route to 172.16.40.0/24 is configured, but traffic still follows the default route. Which two explanations are plausible?

Which IPv6 prefix is used for link-local addresses?

On a broadcast multiaccess segment, R3 has an OSPF priority of 255, but it is in the DROTHER state. Which explanation best fits OSPF behavior?

A network engineer notices that a new switch, SW3, was connected to port GigabitEthernet0/1 on SW1, but the port immediately went into an err-disabled state. The network uses Rapid PVST+ with BPDU Guard enabled globally on all access ports. The engineer checks the logs and sees 'bpduguard error detected' messages. What is the most likely cause of the err-disabled state?

You are connected to R1 via the console. R1 is the DHCP server for the 192.168.50.0/24 LAN. Configure DHCP on R1 to assign addresses from 192.168.50.10 to 192.168.50.200, with default gateway 192.168.50.1 and DNS server 8.8.8.8. Also, configure R1 to act as a DHCP relay agent for the 10.0.0.0/30 link to reach a remote DHCP server at 203.0.113.10. Then, troubleshoot and fix a misconfiguration that causes clients on VLAN 50 to not receive IP addresses.

PCs in VLAN 30 on SwitchA cannot reach servers in VLAN 30 on SwitchB. All other VLANs work across the trunk. What is the most likely cause?

Users on VLAN 20 are not receiving IPv4 addresses from the centralized DHCP server at 10.50.0.10. Users in other VLANs are working normally. Based on the exhibit, which change should fix the issue for VLAN 20 clients?

Two switches are configured to form an EtherChannel, but the bundle never comes up. Which explanation best describes this scenario?

Drag and drop the following steps into the correct order to configure an IPv4 static address on a Windows host, generate an IPv6 EUI-64 address on a Cisco router, verify the router's IPv6 EUI-64 address, and confirm connectivity from the Windows host.

Which two statements accurately describe a default gateway from a host perspective?

Refer to the exhibit. A network engineer is troubleshooting intermittent connectivity between a branch router and the upstream switch. The switch port is manually configured for full-duplex, and the Ethernet cable has been tested and is working properly. The engineer runs the show interfaces GigabitEthernet0/0 command on the router and receives the output shown. Based on the output, what is the most likely cause of the problem?

Which two statements accurately describe good design thinking for wireless guest access?

Drag and drop the following steps into the correct order to configure single‑area OSPFv2 on a router, advertise the 192.168.10.0/24 and 10.0.0.0/24 networks in area 0, and set the GigabitEthernet0/0 interface as passive.

A network team wants visibility into which flows are consuming the most bandwidth between internal subnets. Which technology is most directly associated with that goal?

Drag and drop the following steps into the correct order to configure Root Guard on designated ports, Loop Guard on non-designated ports, and BPDU Guard on PortFast ports, and to recover a port that enters err-disabled due to a BPDU guard violation.

A network administrator is troubleshooting an issue where hosts in the 192.168.20.0/24 subnet cannot reach the Internet, while hosts in 192.168.10.0/24 can. The router is configured for PAT overload using a dynamic pool on the outside interface. The administrator collects the configuration shown in the exhibit. What is the most likely cause of the connectivity problem for the 192.168.20.0/24 subnet?

Why is idempotency valuable in network automation?

Which TWO statements accurately describe the behavior and configuration of floating static routes?

A switchport connected to another switch should carry multiple VLANs, but it was manually configured as an access port. What is the most likely operational result?

Which two statements accurately describe the purpose of least privilege in administration and operations?

An engineer applies this command on an access interface connected to a user PC: switchport port-security violation restrict. What happens if a second unauthorized MAC address appears on the port?

You are connected to R1 via the console. R1's GigabitEthernet0/0 (10.0.0.1/30) connects to ISP router, and GigabitEthernet0/1 (192.168.1.1/24) connects to the internal LAN. The internal network uses 192.168.1.0/24 and needs to access the internet. Configure NAT overload on R1 so that internal hosts are translated to the IP address of GigabitEthernet0/0 when accessing the internet.

A port connected to an end host is configured with PortFast and BPDU Guard. What is the most likely result if a small unmanaged switch is connected and starts sending BPDUs?

A network administrator receives a report that a user on a Windows laptop cannot connect to the internet, although other devices on the same subnet are working. The administrator runs `ipconfig` on the laptop and sees an IP address of 169.254.15.22 with a subnet mask of 255.255.0.0 and no default gateway. Based on this output, what is the most likely cause of the connectivity issue?

A network engineer notices that Host A in VLAN 10 (10.10.10.50/24) can successfully ping its default gateway 10.10.10.1, but cannot ping the VLAN 20 SVI (10.20.20.1) or any hosts in VLAN 20. The SVIs for both VLAN 10 and VLAN 20 are in an up/up state, and the switch's trunk ports are correctly allowing both VLANs. What is the most likely cause?

Which TWO statements correctly describe the causes or implications of CRC errors, runts, giants, or output errors as seen in the output of 'show interface' or 'show interface status'?

Drag and drop the following steps into the correct order to configure Root Guard on a designated port, Loop Guard on a non-designated port, and BPDU Guard on a PortFast port, along with the recovery steps when a port enters err-disabled state.

You are connected to R1. The network consists of R1, SW1, and two hosts (Host-A on VLAN 10, Host-B on VLAN 20). SW1 has two access ports (one per VLAN) and a trunk to R1. Configure R1 for router-on-a-stick inter-VLAN routing. The current configuration has a native VLAN mismatch and a missing subinterface for VLAN 20. Fix these issues so that Host-A and Host-B can ping each other.

You are connected to R1. Configure IPv4 and IPv6 addressing on R1's interfaces and verify reachability to R2. The current configuration has a wrong subnet mask on G0/0, missing default gateway for IPv4, and R1's IPv6 address is configured using EUI-64 while R2 uses a static IPv6 address. Fix these issues so that R1 can ping both R2's IPv4 and IPv6 addresses.

A controller API returns this data: { "device": { "hostname": "Dist-1", "interfaces": [ {"name": "Gig0/0", "status": "up"}, {"name": "Gig0/1", "status": "down"} ] } } Which statement is correct?

A developer is interacting with a REST API exposed by a network controller. Which two statements correctly describe common REST behavior?

A router interface is configured with the prefix 2001:db8:acad:12::/64 and uses EUI-64 to build the interface ID. What is the main purpose of EUI-64 in this context?

You are connected to R1 via console. R1 and R2 are connected via two serial links: Serial0/0/0 (10.0.0.1/30) and Serial0/0/1 (10.0.0.5/30). OSPF is configured on both links. However, the OSPF neighbor adjacency is stuck in EXSTART/EXCHANGE state. You suspect a mismatch in OSPF parameters. You need to identify and fix the issue.

A host address is 10.77.4.141/28. Which address is the network address of the subnet?

A network engineer is troubleshooting an OSPFv3 adjacency issue between two directly connected routers. Both routers are configured for OSPFv3 in area 0 on their GigabitEthernet0/0 interfaces. The engineer checks the OSPFv3 neighbor status on R1 and sees that the neighbor state is stuck in EXSTART. The engineer verifies that both interfaces are up and have IPv6 link-local addresses. What is the most likely cause of this problem?

Drag and drop the following steps into the correct order to troubleshoot an end-to-end connectivity issue using a bottom-up approach.

A network engineer notices that after removing a standard ACL that was applied inbound on the internet-facing interface, the router is now receiving IP packets from the internet with source IP addresses in the 10.0.0.0/8 range, which were previously blocked. What is the most likely cause?

A packet is destined for 192.168.40.130. The routing table contains 192.168.40.0/24, 192.168.40.128/25, and 0.0.0.0/0. Which route is used?

Two OSPF routers connected over Ethernet fail to become neighbors. Their interfaces are up/up and in the same IPv4 subnet. One router uses area 0 and the other uses area 1 on the connecting interfaces. What is the most likely cause?

Exhibit: Hosts on the inside network can reach the internet, but inbound connections to a published web server fail. Static NAT is configured. What is the most likely missing piece?

An administrator configures a GRE tunnel interface on a router with the following: interface Tunnel0, tunnel source GigabitEthernet0/0, tunnel destination 192.168.2.2. What is the main purpose of this configured tunnel?

You are connected to the console of R1. The network team wants to secure remote access. R1 currently has no SSH configuration. The domain name is 'example.com' and you need to generate an RSA key pair of 2048 bits and enable SSH version 2 on vty lines.

A company wants an internal web server to be reachable consistently from the Internet using one known public IPv4 address. Which NAT approach best fits that requirement?

A network engineer has configured an LACP EtherChannel between Switch1 and Switch2 by assigning interfaces to channel-group 1 with the mode passive on both switches. The engineer issues the show etherchannel summary command on Switch1 and sees the output below. The Port-channel interface remains down. Which action resolves the issue?

Refer to the exhibit. A network engineer is investigating intermittent connectivity complaints on a gigabit uplink between two distribution switches. The engineer runs the show interfaces GigabitEthernet0/0 command on one of the switches. Based on the output, what is the most likely cause of the errors?

A PC connected to SW1 cannot reach the default gateway. The access port is assigned to VLAN 20, and the switch output shows that VLAN 20 is inactive. What is the most likely cause?

You are connected to SW1, a Layer 2 switch. Port G0/1 connects to a PC in VLAN 10. Management requires that only one MAC address is allowed on this port, and if a violation occurs, the port should shut down and a log message should be generated. Additionally, you need to ensure that the port enables rapidly and does not wait for STP convergence. Currently, the PC has MAC address aaaa.bbbb.cccc.

A network operations team wants centralized logging from routers and switches and also wants meaningful severity filtering. Which two statements about syslog are correct?

Which TWO statements accurately describe how AI/ML concepts are applied to network operations in modern enterprise networks?

Which security concept is most closely associated with ensuring data has not been altered in an unauthorized way?

A team wants to know which internal hosts are sending the most traffic to a specific data center subnet. Which technology is most directly associated with that visibility goal?

After configuring DHCP snooping on VLAN 10 to prevent rogue DHCP servers, all clients in the VLAN stop receiving DHCP offers from the legitimate DHCP server that is connected to port Gi0/1. The administrator verifies the DHCP server is operational and reachable. What should the technician do next?

Match each HTTP method to its common REST API action.

Drag and drop the following steps into the correct order to configure AAA with a RADIUS server and enable 802.1X port authentication on a Cisco IOS-XE switch.

An engineer wants users to get fast link-up on access ports but also wants the switch to disable a port if another switch is connected and sends BPDUs. Which combination of features best meets that requirement?

A router performing PAT is using a single public IPv4 address for many inside hosts. Which value most often distinguishes one inside flow from another on the same outside address?

Drag and drop the following OSPFv2 neighbor state transitions into the correct order, starting from the initial state when no neighbor information has been received.

Which HTTP method is typically used to retrieve data from a REST API without modifying the resource?

Exhibit: A network engineer wants to identify which applications are consuming most WAN bandwidth over time. Which feature should be enabled on the router?

Which four of the following correctly describe how AI/ML techniques can improve network operations in a modern enterprise? (Choose all that apply.)

Why is traffic to 10.10.10.200 using the EIGRP route instead of the OSPF route, given that both routes have the same prefix length?

Which TWO switch port configurations are required when connecting a Cisco IP phone and a desktop PC to a single access port?

Which TWO statements about IPv4/IPv6 static routing are true?

A small office uses PAT for user Internet access. What mechanism does PAT use to allow many users to share one public address while keeping their sessions distinct?

A network engineer notices that after adding a new switch to the network, a different switch unexpectedly becomes the STP root bridge, disrupting all VLANs. The new switch has the default priority (32768) but has a lower MAC address than all existing switches. What is the most likely cause?

Based on the exhibit, what is the most likely reason the PPP link is failing to authenticate?

A user reports that they cannot access a remote server at IP address 10.10.20.50. The user's PC has IP address 192.168.1.25/24, and the default gateway is 192.168.1.1. The user can successfully ping the default gateway and other hosts on the local subnet. However, pings to 10.10.20.50 fail, and a traceroute shows only the first hop (192.168.1.1) followed by timeouts. Which of the following is the most likely cause?

A DHCP server is located on a different VLAN from the clients. Which feature is required so the clients can still receive addresses?

Two switches are connected via an IEEE 802.1Q trunk. Hosts in VLAN 30 on opposite sides cannot communicate, yet hosts in VLAN 10 communicate normally. Both switches have VLAN 30 in their VLAN database, and the trunk link is operational. What is the most likely cause?

Drag and drop the following steps into the correct order to configure and apply an extended ACL that permits only HTTP traffic from the 192.168.1.0/24 network to the server at 10.0.0.1, with the ACL applied inbound on the router's GigabitEthernet0/0 interface, and then verify the configuration.

In a controller-based design, which statement best describes a northbound API?

A subnet requires 200 usable host addresses. Which prefix is the smallest that meets the requirement?

Which term in the CIA triad refers to ensuring systems and data remain accessible when needed?

Which TWO statements correctly describe the configuration and use of a voice VLAN on a Cisco switch port?

You are connected to SW1, a Layer 2 switch. The network administrator wants to prevent unauthorized switches from being connected to access ports. Port G0/1 is an access port in VLAN 10. You need to configure BPDU Guard on this port to protect against STP loops caused by rogue switches. Additionally, enable PortFast for immediate transition to forwarding.

Which STP port state on a classic 802.1D switch listens for BPDUs and prepares to participate in the topology, but does not yet learn MAC addresses?

You are connected to R1, a Cisco IOS-XE router. Configure SNMP v2c with read-only community 'NetOpsRO' and SNMP v3 with user 'AdminUser' using SHA authentication (password: AuthPass1) and AES-128 encryption (password: PrivPass2). Also enable SNMP traps to the NMS at 192.0.2.10 with community 'TrapComm'. Additionally, configure NetFlow export to 192.0.2.20 using version 9, and ensure the flow exporter is applied to GigabitEthernet0/0. Verify your configuration using 'show snmp' and 'show ip cache flow'.

A network technician configures a Windows 10 PC with a static IPv6 address of 2001:db8:acad:1::100/64 and a default gateway of 2001:db8:acad:2::1. The PC can communicate with other hosts in the 2001:db8:acad:1::/64 subnet, but it cannot access any resources on other subnets, even though IPv4 connectivity through the same network works normally. What is the most likely reason for this issue?

A host is configured as 10.10.20.190/26. Which range contains usable host addresses for that subnet?

A technician is troubleshooting a connection between two routers, R1 and R2, connected back-to-back using Ethernet cables. Both routers have their interfaces configured and are in an 'up/up' state. R1's interface uses 192.168.1.1/24, and R2's interface uses 192.168.2.1/24. When the technician attempts to ping R2 from R1, the ping fails. What is the most likely cause?

Which TWO commands would a network engineer use to verify that a Windows client has received an IP address from a DHCP server and can resolve a domain name to an IP address?

R1 receives an OSPF route to 10.55.0.0/16 and already has a static route to 10.55.10.0/24. Which route will be used for traffic sent to 10.55.10.25?

A switch interface is configured as `dynamic desirable`, and the peer interface is configured as `dynamic auto`. What is the most likely result?

Drag and drop the cable/transceiver types on the left to the correct distance and speed descriptions on the right.

Refer to the exhibit. An engineer configured PortFast on interface GigabitEthernet0/1, which connects to a server that does not participate in spanning tree. However, the port remains in the listening state for the full forward delay period before transitioning to forwarding. The engineer issues the show spanning-tree vlan 10 detail command. Based on the output, what is the most likely cause?

Drag and drop the following steps into the correct order to configure and recover from a BPDU guard violation on a PortFast-enabled access port in RSTP.

A router has the following routes in its table: 172.16.0.0/16, 172.16.20.0/24, and 172.16.20.128/25. Which route is used for traffic to 172.16.20.200?

Which STP role identifies the port on a non-root switch that has the best path back to the root bridge?

A router has a directly connected route to 10.1.1.0/24 and a static default route. Which route is used for traffic to 10.1.1.200?

You are connected to R1 via the console. R1 is a newly deployed router that connects two subnets: 192.168.1.0/24 on GigabitEthernet0/0 and 192.168.2.0/24 on GigabitEthernet0/1. There is a default route to the Internet via ISP router at 203.0.113.1, but the network policy requires that traffic from 192.168.1.0/24 to the Internet must exit via a different next-hop 203.0.113.2. You need to implement policy-based routing on R1 to forward traffic from source 192.168.1.0/24 to 203.0.113.2, while all other traffic uses the default route via 203.0.113.1.

Which two statements accurately describe the role of a switch MAC address table?

You are connected to R1, a multilayer switch acting as the STP root for VLAN 10. Configure Root Guard on port GigabitEthernet0/1 (designated port) to protect against superior BPDUs from an unauthorized switch, Loop Guard on uplink GigabitEthernet0/2 to prevent loops, and BPDU Guard on PortFast-enabled GigabitEthernet0/3. After configuration, a superior BPDU arrives on G0/1, blocking the port; verify the Root Guard state and ensure BPDU Guard triggers err-disable on G0/3.

A subnet uses the mask 255.255.255.224. How many usable host addresses does it provide?

Refer to the exhibit. A network engineer is verifying OSPF routing on R1. All routers in the topology are expected to reside in OSPF area 0, and the network 172.16.0.0/16 should be advertised from R2 within the same area. The engineer issues the show ip route 172.16.0.0 command on R1 and sees the output in the exhibit. The engineer expected to see an intra-area route (O) instead of an inter-area route (O IA). What is the most likely cause of this discrepancy?

A standard ACL and an extended ACL are both available for a design. Which requirement most strongly indicates that an extended ACL is needed?

R1 and R2 are connected via a shared Ethernet segment. Both routers are configured in OSPF area 0 and are on the same IP subnet. OSPF authentication is enabled on both interfaces, but the adjacency is not forming. What is the most likely reason?

R3 has the static route 'ip route 172.20.8.0 255.255.255.0 192.168.1.1'. Packets destined for 172.20.8.0/24 are being dropped. What is the most likely cause?

A user connects a Cisco IP Phone with a PC attached to the phone's PC port to switch interface GigabitEthernet0/5. The PC obtains an IP address and can reach the network, but the phone displays "Configuring IP" and never registers. Based on the exhibit outputs, what is the most likely cause?

Why is the combination of strong authentication and centralized logging generally better than using either one alone?

What is an autonomous system in basic BGP terminology?

A host address is 10.100.12.94/26. Which address is the broadcast address for that subnet?

You are connected to R1, a multilayer switch acting as a DNS client and DNS server for the local network. The network uses 192.168.1.0/24 for internal hosts. Users report that hostnames like 'server1.example.com' fail to resolve. Diagnose and fix the DNS resolution issue using nslookup and dig. Ensure that R1 can resolve both forward and reverse DNS queries correctly.

A branch router is acting as a DHCP server. Which two parameters can it provide directly to clients through DHCP?

An administrator needs to configure an ACL to block HTTP traffic from subnet 10.10.10.0/24 to the web server at 172.16.1.10 while permitting all other traffic. Which ACL entry should be placed first?

An administrator wants to prevent a specific subnet from using Telnet to reach network devices, while still allowing SSH from that same subnet. What is the strongest reason a standard ACL is not enough by itself?

Which three statements about Power over Ethernet (PoE) and PoE+ standards are correct? (Choose three.)

Which NAT design is most appropriate when many inside users need outbound Internet access through one public IPv4 address, but no inbound server publishing is required?

Exhibit: Users complain of slow wireless performance in a dense office even though signal strength is strong. Multiple APs are using channels 1, 2, and 3 on 2.4 GHz. Which change is most appropriate?

Drag and drop the following steps into the correct order to configure HSRP on an interface and verify the active/standby election process, including failover and verification.

A switch shows a clock that is several minutes off from other devices even though an NTP server has been configured. Which issue is the most likely cause?

Users on a new access switch can reach devices in their own VLAN but cannot reach the default gateway on the distribution switch. Based on the exhibit, what is the most likely cause?

A network engineer notices that the router interface GigabitEthernet0/1 is in an 'administratively down' state in the output of the show ip interface brief command, preventing connectivity to the subnet connected to that interface. What is the most likely cause?

Drag and drop the following OSPFv2 neighbor state transitions and DR/BDR election steps into the correct order for a multi-access network where a new router joins an existing OSPF area.

An engineer wants remote administrative access to remain available but also wants session contents protected in transit. Which management choice best supports that goal?

A network engineer enters the following configuration on R1 and R2, but R1 cannot form an OSPF adjacency with R2 on interface GigabitEthernet0/0. R1# show running-config interface GigabitEthernet0/0 interface GigabitEthernet0/0 ip address 10.0.0.1 255.255.255.0 ip ospf hello-interval 10 ip ospf dead-interval 40 ip ospf 1 area 0 ! R2# show running-config interface GigabitEthernet0/0 interface GigabitEthernet0/0 ip address 10.0.0.2 255.255.255.0 ip ospf hello-interval 5 ip ospf dead-interval 20 ip ospf 1 area 0 What is the most likely cause of the failure?

Why is HTTPS preferred over HTTP when accessing sensitive controller APIs?

An API response returns a list of interface objects in JSON. Which structure most likely represents that list?

A subnet uses the prefix /29. How many usable host addresses are available in each subnet?

A network engineer needs to automate the configuration of multiple Cisco IOS XE routers in a data center. The team requires a standard, vendor-neutral data modeling language to define the configuration parameters, and they need a protocol that uses XML-based remote procedure calls over SSH for secure, reliable configuration transactions. Which combination of technologies best meets these requirements?

A network engineer notices that internal hosts (192.168.1.0/24) can reach external servers on the internet, but replies from external servers never reach the internal hosts. The router R1 is configured with dynamic NAT to translate the internal subnet to a pool of public IPs (203.0.113.10-203.0.113.20). The engineer runs 'show ip nat translations' and sees only a few stale translations. What is the most likely cause of the issue?

You are connected to a Cisco 9800 WLC (WLC1) via its management interface. A wireless client reports association failures with SSID 'CorpNet'. The client uses WPA3-Personal, but the WLAN is configured for WPA2. Additionally, the SSID is hidden and the client is on the wrong VLAN (VLAN 20 instead of VLAN 100). Fix these issues so the client can associate successfully with WPA3, on VLAN 100, and with the SSID broadcast enabled.

An administrator has just configured OSPF in a single area between router R1 and router R2, which are directly connected via their Gi0/0 interfaces with IP addresses 10.0.0.1/30 and 10.0.0.2/30. On R1, the command show ip ospf neighbor shows no entries, and a further check on R2 with show ip ospf interface gi0/0 indicates that the interface is passive. Which configuration error is most likely causing the adjacency failure?

A Layer 2 switch port connected to an end host should move to forwarding quickly but also shut down if a BPDU is received. Which pair of features best supports that design?

After configuring the area 0 range 10.0.0.0 255.255.0.0 command on an OSPF ABR, a technician finds that a host at 10.0.5.100 in Area 1 cannot reach hosts in Area 0. The ABR’s OSPF database shows only the summary 10.0.0.0/16 in Area 0, and no individual /24 routes. What is the most likely cause?

You are connected to R1 via the console. The network administrator reports that PC1 (connected to R1's GigabitEthernet0/1) cannot reach the internet. Troubleshoot the issue step by step. The current configuration and show outputs are provided.

You are connected to R1 via console. R1 has two upstream paths to the Internet: a primary via ISP1 (G0/0 10.1.1.1/30) and a backup via ISP2 (G0/1 10.2.2.1/30). The backup path should only be used when the primary fails. The default route to ISP1 has been configured, but you must now configure a floating static default route to ISP2 with an administrative distance of 200.

A user reports that their computer cannot access the network. The technician checks the computer's IP configuration and finds an APIPA address (169.254.x.x). The computer is connected to a switch port on VLAN 20. The DHCP server is located on VLAN 1. The technician then examines the router's interfaces using 'show ip interface brief' and sees that all interfaces shown are up/up. What should the technician do next?

Drag and drop the following steps into the correct order to describe how data is encapsulated as it travels down the OSI model layers.

A network administrator has configured a switch port to support a VoIP phone and a desktop PC. Users report that the desktop PC cannot obtain an IP address via DHCP, while the VoIP phone registers successfully. The switch port is up/up, and the desktop is connected to the phone's PC port. What is the most likely cause of the issue?

Why is multifactor authentication generally stronger than password-only access?

A technician is troubleshooting an OSPF network. On a broadcast segment, R1 is the DR and R2 is the BDR. R1's interface GigabitEthernet0/0 is shut down for maintenance. The technician expects that R2 will assume the DR role, but instead a new DR election occurs and another router is elected DR. What is the most likely cause?

A script authenticates to a controller API and receives a token that it presents in later requests. Which two statements about that token-based workflow are correct?

Based on the exhibit, which action is most likely required to allow AP-22 to join the controller successfully?

A host is configured with 192.168.10.129/25. Which subnet contains that host?

Exhibit: An access switch shows Gi1/0/10 as err-disabled shortly after an IP phone and a workstation are connected through the same wall jack. What is the most likely cause?

You are connected to R1. Configure SNMP v2c with a read-only community string 'monitorRO' and a read-write community string 'controlRW', and enable SNMP traps for link status to the management server at 203.0.113.100. Additionally, configure NetFlow to export version 9 flow records to the same server on UDP port 2055, and ensure that only traffic from the 10.10.10.0/24 network is monitored. Finally, verify your configurations with the appropriate show commands.

A network technician is troubleshooting a connectivity issue where a user's email client cannot send messages, but the client can receive emails. The technician uses a protocol analyzer and sees that the client is successfully resolving the mail server's domain name to an IP address and establishing a TCP connection, but the server responds with an application-layer error. At which layers of the OSI model are the problem and the successful operations occurring, respectively?

Which three of the following are correct steps in the process of CDP (Cisco Discovery Protocol) neighbor discovery? (Choose three.)

Drag and drop the following steps into the correct order to configure a WLAN for WPA3-Enterprise on a Cisco WLC and sequence a wireless client association process.

Match each NAT term to its most accurate description.

Why is a northbound API valuable to orchestration tools in a controller-based network?

Which two features commonly strengthen access-switch security for user-facing ports? (Choose two.)

Exhibit: A user reports intermittent connectivity after a new switch was connected to an access port. Which feature would have prevented this by immediately disabling the port when a BPDU was received?

You are connected to R1 via console. The link between R1 and R2 is experiencing packet loss and CRC errors. Configure interface speed and duplex on R1's GigabitEthernet0/0 to match R2's settings, then replace the SFP module with one that supports the required 2 km distance. Finally, verify the interface is operational without errors.

A monitoring system already collects Syslog and SNMP data. The network team now wants visibility into which applications or host conversations are driving link utilization. What is the strongest addition?

A host address is 172.22.14.99/27. Which address is the broadcast address of the subnet?

An administrator deploys a new WLAN on a Cisco 9800 WLC using WPA3-Personal (SAE) with AES encryption. A single 802.11ax laptop running Windows 10 fails to connect, displaying an authentication timeout despite entering the correct passphrase. Other clients, including legacy 802.11ac devices, connect without issue.

You are connected to a single switch, SW1, which is a Cisco Catalyst 2960 running Cisco IOS. Configure port GigabitEthernet0/1 as an access port for a Cisco IP phone and a PC on the same VLAN (Voice VLAN 20, Data VLAN 10). The switch must provide PoE to the phone. Additionally, configure GigabitEthernet0/2 as an access port for a wireless access point (AP) that requires PoE. Verify both configurations using the appropriate show commands. The current running-config is incomplete; you must add the necessary commands.

Which data format is most commonly used in REST APIs because it is lightweight and easy for applications to parse?

A switchport connected to an IP phone and a PC must carry user traffic and voice traffic separately. Which feature is designed for that purpose on a Cisco access port?

Two routers, R1 and R2, are connected via a serial link. The interface on R1 shows 'Serial0/0 is up, line protocol is down' and no pings succeed across the link. You check the configuration and notice R1 has 'encapsulation ppp' but R2's serial interface was mistakenly left at the default encapsulation hdlc.

R1 and R2 are directly connected via Ethernet on interface G0/0. Both interfaces are in the same subnet and configured for OSPF area 0. After enabling OSPF, R1's G0/0 is stuck in the INIT state in the OSPF neighbor table. What is the most likely cause?

Drag and drop the following steps into the correct order to configure a Cisco switch access port with a data VLAN and a voice VLAN.

Which two statements accurately describe DHCP?

As a general rule, where should an extended ACL be placed?

A router has a static route configured: ip route 10.200.0.0 255.255.0.0 GigabitEthernet0/1. The output of show ip interface brief shows that interface GigabitEthernet0/1 is administratively down. Why is the route to 10.200.0.0/16 present in the running configuration but absent from the routing table?

A network engineer is troubleshooting OSPFv3 adjacency between two directly connected Cisco routers, R1 and R2, both running IOS-XE. The engineer configures OSPFv3 on both routers but notices that the adjacency does not form. The engineer runs 'show ospfv3 neighbor' on R1 and sees no neighbors. What is the most likely cause of this issue?

You are connected to R1, a Cisco IOS-XE router that provides connectivity for the 192.168.10.0/24 network. The network operations team uses a Python script with netmiko to push configuration changes. However, the script fails to connect to R1. You need to verify the SSH configuration on R1.

A route table shows both a default route and a more specific route to 192.168.50.0/24. Which two statements describe how packets destined for 192.168.50.25 are handled?

A router is configured for PAT using the WAN interface address. Which command element is most directly associated with allowing many internal users to share that single outside address?

A technician is troubleshooting a connectivity issue where a workstation connected to a Cisco switch port cannot ping other hosts that are in the same VLAN 10 segment. The technician runs the show mac address-table command and notices that the workstation's MAC address is listed on VLAN 1, not VLAN 10. What is the most likely cause?

Which TWO statements about interpreting routing table output are true? (Choose two.)

Exhibit: Users report no internet access after PAT was configured. The inside and outside interfaces are marked correctly. Which missing configuration is the most likely cause?

Drag and drop the following steps into the correct order to configure and apply an extended IPv4 ACL on a Cisco router to block Telnet traffic from subnet 192.168.1.0/24 to host 10.0.0.1 and permit all other IP traffic.

A company wants internal users to share one public IPv4 address for outbound Internet access, while keeping sessions separate. Which NAT approach best meets that requirement?

Exhibit: A host on VLAN 10 can ping the local SVI but not a server in VLAN 20. The Layer 3 switch has both VLAN interfaces up. What is the next item to verify first?

You are connected to R1 via the console. SNMP v2c community strings (public RO, private RW) are already configured. The network has a management server at 10.1.1.100 and a NetFlow collector at 10.1.1.200. Configure SNMP traps to the management server for link status changes. Also configure NetFlow on interface GigabitEthernet0/0 to export version 9 to the collector, with a source interface of Loopback0 (10.255.255.1/32).

A host address is 10.10.10.14/29. Which address is the broadcast address for its subnet?

A switch should learn one MAC address on an access port and shut the port down if a second unauthorized device appears. Which two port-security settings support that requirement?

A network administrator wants to secure remote CLI access to a Cisco router, moving beyond simple username/password authentication. Which approach best achieves this goal?

You are connected to R1. The network uses a single router with two subnets: 192.168.1.0/24 (connected to GigabitEthernet0/0) and 10.0.0.0/30 (connected to GigabitEthernet0/1). Configure an extended named ACL called 'FILTER_HTTP' that permits HTTP traffic (TCP port 80) from the 192.168.1.0/24 subnet to any destination, and includes an explicit deny statement to deny all other IP traffic. Apply the ACL inbound on GigabitEthernet0/0. Then verify that HTTP traffic is allowed and all other traffic is blocked.

A user reports that a laptop can connect to the correct SSID but repeatedly fails authentication when joining the WLAN. Which category of issue is most strongly indicated?

Based on the exhibit, why is the ACL blocking more traffic than intended?

You are connected to SW1 via the console. SW1 is a Layer 2 switch with two VLANs (10 - Sales, 20 - Engineering). Port G0/1 is connected to a PC in VLAN 10, and port G0/2 is connected to a PC in VLAN 20. The switch needs to be configured to allow inter-VLAN communication using an external router connected to port G0/3. Currently, the PCs cannot communicate across VLANs. Configure the switch to support Router-on-a-Stick with VLAN 10 as the native VLAN on the trunk.

Exhibit: An engineer wants a device to send only warning messages and more critical events to a syslog server. Which logging level should be configured?

A host with address 172.16.5.10/23 wants to determine whether 172.16.6.20 is on the same local network. What is the correct conclusion?

You are connected to R1. Use RESTCONF to retrieve all operational interface statistics from the ietf-interfaces YANG module, then modify the description of GigabitEthernet0/1 to 'Link to R2 via RESTCONF' using a PATCH request. The device is reachable at 203.0.113.1 with port 443, username 'admin', password 'cisco123'. Identify the error that would occur if you used a PATCH with Content-Type: application/json instead of application/yang-data+json.

Refer to the exhibit. A network engineer is troubleshooting an EtherChannel on R1 that is not passing traffic. The output of the show etherchannel summary command is displayed. What is the most likely cause?

You are connected to the console of R1. The network has a point-to-point serial link between R1 and R2. The link is down and the line protocol is down. The cable is a DCE/DTE crossover, and R1 is the DCE. The initial configuration shows the interface with an IP address but no clock rate set.

Which pairing is correct?

Why is HTTPS usually preferred over HTTP when accessing a controller API?

Which two statements accurately describe the value of source restriction on administrative access?

Match each IPv4-related concept to its most accurate role.

Which IPv6 address type is automatically created on an interface and used for link-local communication?

A network administrator notices that syslog messages from a core router are arriving at the syslog server with timestamps that are hours behind other devices. The router’s NetFlow exports also show incorrect start and end times for flows, making traffic analysis unreliable. The administrator verifies that all router interfaces are up and that the SNMP community strings on the router match the NMS.

Why does DNS make networks easier for people to use?