N10-009 Practice Test 4 — 10 Questions

Question 1

A network engineer is troubleshooting connectivity issues between two data center switches that are configured to support jumbo frames with an MTU of 9000. The link is a 10 Gigabit Ethernet fiber connection. Large file transfers fail, but small transfers succeed. What is the most likely cause?

Choose an answer to begin — your selection is scored in the full session.

Accepted Answer

C. The most likely cause is that an intermediate device (such as a router or another switch) along the Layer 2 path is not configured for jumbo frames and has a standard MTU of 1500. Since both end switches support an MTU of 9000, large frames are sent but are dropped when they reach the intermediate device that cannot handle them. Small frames (≤1500 bytes) pass through successfully because they fit within the standard MTU.

Answer

A

Answer

B

Answer

D

Question 2

A network administrator is configuring a new switch to carry traffic for multiple VLANs on a single link to a router. Which IEEE standard is used for VLAN tagging on Ethernet trunks?

Accepted Answer

802.1Q. 802.1Q is the IEEE standard that defines VLAN tagging on Ethernet trunks, inserting a 4-byte tag into the Ethernet frame to identify VLAN membership. This allows multiple VLANs to traverse a single link between a switch and a router, enabling inter-VLAN routing without separate physical interfaces.

Answer

802.3af

Answer

802.1D

Answer

802.11ac

Question 3

A user can access a website by its IP address (e.g., 203.0.113.5) but cannot access it by its domain name (example.com). Other users on the same subnet can access the website by domain name. Which of the following should the technician check FIRST?

Accepted Answer

Check the local hosts file. The issue is isolated to a single user who can reach the website by IP but not by domain name, while other users on the same subnet have no problem. This indicates a client-side DNS resolution problem. The first thing to check is the local hosts file (e.g., C:\Windows\System32\drivers\etc\hosts) for any incorrect or outdated entries that might be overriding DNS resolution. If the hosts file has an incorrect mapping for example.com, the browser will use that instead of querying the DNS server, causing the failure. Checking DNS server configuration is appropriate if the hosts file is clean.

Answer

Check the DNS server configuration on the network

Answer

Check the website's DNS records

Answer

Check the user's browser proxy settings

Question 4

A network engineer wants to segment a LAN into multiple broadcast domains without purchasing additional hardware. Which of the following technologies should be implemented?

Accepted Answer

VLANs. VLANs (Virtual Local Area Networks) allow a network engineer to logically segment a single physical LAN switch into multiple isolated broadcast domains without purchasing additional hardware. By assigning switch ports to different VLAN IDs, broadcast traffic is confined to ports within the same VLAN, effectively creating separate Layer 2 networks on the same switch infrastructure.

Answer

Subnetting

Answer

VPN

Answer

NAT

Question 5

A network engineer is reviewing RFC 1918 address ranges to plan a private IP addressing scheme. Which of the following IP addresses falls within the private address space for Class A?

Accepted Answer

10.10.10.1. RFC 1918 defines the Class A private address range as 10.0.0.0/8, which includes all addresses from 10.0.0.0 to 10.255.255.255. 10.10.10.1 falls within this range, making it a valid private IP address for internal network use.

Answer

172.16.0.1

Answer

192.168.1.1

Answer

172.32.0.1

Question 6

A network administrator needs to ensure high availability for a critical server that has two network interfaces connected to two different switches. Which configuration should be implemented to provide failover and load balancing at the network layer?

Accepted Answer

Link aggregation (LACP). Link Aggregation (LACP) allows multiple physical network interfaces to be combined into a single logical link, providing both failover and load balancing at Layer 2. In this scenario, the server's two NICs are connected to two different switches; LACP can be configured across the two switches (if they support Multi-chassis Link Aggregation) or the NICs can be set up in an active/standby team for failover. This satisfies the requirement for high availability and load balancing at the network layer (Layer 2/3 boundary). Virtual IP protocols like VRRP/HSRP are designed for gateway redundancy, not for server NIC failover.

Answer

Virtual IP (VRRP/HSRP)

Answer

Spanning Tree Protocol (STP)

Answer

Port mirroring

Question 7

A switch port is configured as a trunk with native VLAN 99. When a frame tagged with VLAN 99 is received on the trunk, the switch displays an error. What is the most likely issue?

Accepted Answer

The remote switch is tagging frames on the native VLAN. The native VLAN is the VLAN that carries untagged traffic on an 802.1Q trunk. By design, frames belonging to the native VLAN should be sent untagged. When a switch receives a frame tagged with the native VLAN ID (VLAN 99), it indicates a mismatch in native VLAN configuration between the two ends of the trunk. The switch logs an error because it expects native VLAN frames to be untagged, but the remote switch is incorrectly tagging them.

Answer

The trunk is using 802.1Q encapsulation and the remote switch expects ISL

Answer

The remote switch is sending frames on VLAN 99 as untagged

Answer

The allowed VLAN list does not include VLAN 99

Question 8

A network administrator has just connected a new access switch to the core switch via a trunk port. The administrator configured the trunk port on both switches with the same allowed VLAN list. However, hosts on VLAN 10 connected to the new access switch cannot communicate with hosts on VLAN 10 on the core switch. The trunk is operational and shows up/up. What is the most likely cause?

Accepted Answer

A) VLAN 10 has not been created on the new access switch. The most likely cause is that VLAN 10 has not been created on the new access switch. Even though the trunk port is up/up and the allowed VLAN list matches, a switch will not forward traffic for a VLAN that does not exist in its local VLAN database. Without the VLAN being created, the switch drops all frames tagged with VLAN 10, preventing communication between hosts on that VLAN across the trunk.

Answer

B) Native VLAN mismatch on the trunk

Answer

C) Trunk encapsulation mismatch (ISL vs 802.1Q)

Answer

D) STP is blocking the VLAN 10 traffic on the trunk

Question 9

A network administrator is preparing to upgrade the firmware on a critical router. Which document should the administrator consult to understand the steps required to minimize downtime and ensure a successful upgrade?

Accepted Answer

Change management plan. The change management plan documents the approved procedures, rollback steps, and communication protocols for performing maintenance on critical infrastructure. Consulting this plan ensures the administrator follows the organization's predefined steps to minimize downtime and mitigate risks during the firmware upgrade.

Answer

SLA

Answer

Network diagram

Answer

Baseline performance report

Question 10

After replacing a faulty network cable, a user reports that they can access local resources but not the internet. The technician verifies that the user's IP address is 192.168.1.100 with a subnet mask of 255.255.255.0 and a default gateway of 192.168.1.1. The technician can ping the default gateway successfully. Which of the following should the technician check NEXT?

Accepted Answer

A) DNS configuration. The user can access local resources and successfully ping the default gateway, which confirms that Layer 2 and Layer 3 connectivity to the local network is working. The inability to access the internet while local access works points to a name resolution failure, as the browser relies on DNS to translate domain names to IP addresses. Checking DNS configuration is the logical next step because a misconfigured or missing DNS server would prevent internet access even when IP connectivity is intact.

Answer

B) DHCP server

Answer

C) Router's firewall ACLs

Answer

D) Switch port VLAN assignment