350-401 Architecture — Timed 15 Questions

Question 1

Which TWO characteristics are true about Cisco StackWise virtual technology? (Choose two.)

Accepted Answer

It allows multiple physical switches to operate as a single logical switch.. Cisco StackWise Virtual allows two physical switches to be interconnected using regular Ethernet links (not dedicated stacking cables) to operate as a single logical switch. This simplifies management because the stack can be managed via a single IP address. It does not require dedicated cables, does not require identical hardware models (mixed models are allowed), and supports only 2 member switches (not up to 9). Therefore, the correct characteristics are A and C.

Answer

Each member switch must have the same hardware model.

Answer

It requires dedicated stacking cables for interconnectivity.

Answer

It supports up to 9 member switches in a stack.

Question 2

An engineer is troubleshooting intermittent connectivity issues between two data center switches. The link is a 10GE LACP port-channel. Which misconfiguration could cause packet loss?

Accepted Answer

MTU size is set to 1500 on one switch and 9000 on the other.. An MTU mismatch between two switches in a port-channel can cause packet fragmentation or drops. With LACP, both sides must have matching MTU settings to ensure proper frame forwarding. If one switch has an MTU of 1500 and the other 9000 (jumbo frames), packets exceeding 1500 bytes will be dropped by the switch with the smaller MTU, causing intermittent packet loss. In contrast, an active/passive LACP configuration is valid and commonly used; it does not cause packet loss if both sides are properly configured. Passive-passive would prevent the port-channel from forming, but that is not the case here.

Answer

Auto-negotiation is disabled on both ends.

Answer

Spanning-tree BPDU guard is enabled on the port-channel.

Answer

One switch is configured with active LACP and the other with passive LACP.

Question 3

A network engineer is designing a campus network with high availability for critical services. Which Cisco technology enables traffic to be forwarded to an alternate next hop in the event of a first-hop router failure, without requiring any configuration changes on the hosts?

Accepted Answer

HSRP. HSRP (Hot Standby Router Protocol) is a Cisco-proprietary FHRP that allows multiple routers to share a virtual IP and MAC address, providing transparent failover. Hosts are configured with the virtual IP as their default gateway, so when the active router fails, the standby router takes over without any host configuration changes. This directly meets the requirement for high availability without host reconfiguration.

Answer

Static default route with a floating static

Answer

GLBP

Answer

VRRP

Question 4

A company is deploying a wireless network in an office with high client density. Which Cisco architecture is best suited to handle client roaming without requiring a central controller for every roaming event?

Accepted Answer

FlexConnect. FlexConnect (option D) is the correct architecture because it allows client data traffic to be switched locally at the remote site, while the control plane remains centralized. This design eliminates the need for a central controller to process every roaming event, as clients can roam between FlexConnect APs using local switching and 802.11r (Fast Roaming) without requiring a WLC in the data path.

Answer

Mesh networking

Answer

Autonomous APs

Answer

Centralized switching with a WLC

Question 5

An enterprise is using OSPF in a multi-area design. Area 1 is a regular area, and Area 2 is a totally stubby area. Which LSA types are present in Area 2?

Accepted Answer

Type 1, Type 2, Type 3 (including default). In a totally stubby area, the ABR blocks Type 4 and Type 5 LSAs and replaces all Type 3 inter-area routes with a single default route (Type 3 LSA with link-state ID 0.0.0.0). Therefore, only Type 1 (router), Type 2 (network), and the default Type 3 LSAs are present. This matches option A.

Answer

Type 1, Type 2, Type 3, Type 5

Answer

Type 1, Type 2, Type 4, Type 5

Answer

Type 1, Type 2, Type 3 (including default), Type 4

Question 6

A network engineer is troubleshooting a routing loop in an EIGRP network. Which mechanism is designed to prevent routing loops by causing a router to reject routes that are learned from a neighbor that is not the successor?

Accepted Answer

Feasibility condition. The feasibility condition is a loop-prevention mechanism unique to EIGRP. It ensures that a router only accepts a route from a neighbor if that neighbor's reported distance (RD) to the destination is less than the router's own feasible distance (FD). This guarantees that the path through that neighbor is loop-free, effectively rejecting routes learned from any neighbor that is not the successor.

Answer

Split horizon

Answer

Route poisoning

Answer

Hold-down timers

Question 7

A company is implementing QoS in a network where voice traffic must have strict priority over all other traffic. Which queuing mechanism should be used on the outbound interface of a router to ensure voice packets are always sent first?

Accepted Answer

Low Latency Queuing (LLQ). Low Latency Queuing (LLQ) is the correct choice because it combines Class-Based Weighted Fair Queuing (CBWFQ) with a strict priority queue, ensuring that voice traffic (marked with EF or CS5) is always dequeued before any other traffic class. This guarantees low latency and jitter for real-time traffic, which is essential for voice quality.

Answer

Random Early Detection (RED)

Answer

First In First Out (FIFO)

Answer

Class-Based Weighted Fair Queuing (CBWFQ)

Question 8

A network administrator is configuring a new VLAN 100 on a switch and wants to ensure that the VLAN is created and active. Which command is required to create a VLAN in the VLAN database?

Accepted Answer

vlan 100. The 'vlan 100' command is executed in global configuration mode to create a VLAN in the VLAN database on a Cisco IOS switch. This command creates the VLAN and places the switch into VLAN configuration mode, where optional parameters like name can be set. The VLAN is active immediately upon creation, provided the switch is in VTP server or transparent mode.

Answer

interface vlan 100

Answer

name VLAN100

Answer

switchport access vlan 100

Question 9

An engineer is troubleshooting a network where OSPF neighbors are stuck in the EXSTART state. What is the most likely cause?

Accepted Answer

MTU mismatch between the routers. The EXSTART state in OSPF indicates that routers have formed a bidirectional communication (2-Way state) and are now attempting to exchange Database Description (DBD) packets to negotiate the master/slave relationship and the initial sequence number. An MTU mismatch between the routers is the most common cause of neighbors being stuck in EXSTART because the router with the smaller MTU will drop DBD packets that exceed its interface MTU, preventing the exchange from progressing to the Loading state.

Answer

Dead timer mismatch

Answer

Authentication misconfiguration

Answer

Mismatched OSPF area IDs

Question 10

A company is deploying a WAN with MPLS VPN and wants to ensure that customer traffic is isolated from other customers. Which technology is used to maintain separation in the MPLS core?

Accepted Answer

Virtual Routing and Forwarding (VRF). VRF (Virtual Routing and Forwarding) is the technology used in MPLS VPN to maintain customer traffic separation within the MPLS core. Each customer is assigned a unique VRF on the Provider Edge (PE) router, which maintains a separate routing table and forwarding instance, ensuring that traffic from one customer never crosses into another customer's routing domain. This separation is enforced at Layer 3, independent of the MPLS label switching that occurs in the core.

Answer

VLAN tagging

Answer

MPLS labels

Answer

IPsec tunnels

Question 11

Which TWO statements are correct about Cisco SD-Access architecture? (Choose two.)

Accepted Answer

VXLAN encapsulation is used for data plane traffic within the fabric.. VXLAN is the encapsulation protocol used in the Cisco SD-Access fabric to carry data plane traffic between fabric edge nodes. VXLAN provides a Layer 2 overlay over a Layer 3 underlay, enabling scalable segmentation and mobility without VLAN limitations.

Answer

Wireless access points must be directly connected to the fabric edge switches.

Answer

Fabric edge nodes are responsible for connecting the fabric to external networks.

Answer

The fabric uses VLANs to isolate tenant traffic.

Question 12

Which TWO are benefits of using a spine-leaf architecture in a data center? (Choose two.)

Accepted Answer

Predictable latency between any two devices. A is correct because spine-leaf architecture ensures that every leaf switch is connected to every spine switch, creating a full-mesh topology. This design guarantees that traffic between any two leaf switches traverses at most one spine hop, resulting in predictable, consistent latency regardless of which devices are communicating.

Answer

Increased number of single points of failure

Answer

Increased broadcast domain size

Answer

Reduced need for VLANs

Question 13

A large enterprise has a campus network with a collapsed core design. The core switch connects to two distribution switches, each serving several access switches. The network uses OSPF as the IGP. Recently, after a link failure between the core and distribution switch A, the network experienced a 30-second outage before converging. The engineer wants to improve convergence time to under 5 seconds. The budget is limited, so hardware upgrades are not an option. The engineer is considering the following actions:
A. Enable OSPF Fast Hello on all interfaces.
B. Reduce OSPF dead timer to 1 second and hello timer to 333 milliseconds.
C. Implement OSPF LSA throttling with a minimum interval of 0 ms.
D. Use OSPF incremental SPF (iSPF).

Which action will provide the most significant improvement in convergence time for this scenario?

Accepted Answer

Reduce OSPF dead timer to 1 second and hello timer to 333 milliseconds.. Reducing the OSPF dead timer to 1 second and hello timer to 333 milliseconds directly addresses the 30-second outage caused by the link failure. The default dead timer (40 seconds on broadcast networks) is the primary contributor to convergence delay, as OSPF must wait for the dead interval to expire before declaring a neighbor down. By lowering these timers, failure detection drops from 40 seconds to approximately 1 second, which is the most impactful single change for convergence under budget constraints.

Answer

Enable OSPF Fast Hello on all interfaces.

Answer

Implement OSPF LSA throttling with a minimum interval of 0 ms.

Answer

Use OSPF incremental SPF (iSPF).

Question 14

A small business has a single router connected to the internet and a switch for the LAN. They want to implement VLANs to separate guest and corporate traffic. The router has only one physical interface to the switch. The network engineer proposes using subinterfaces with 802.1Q trunking on the router interface. Which configuration step is required on the switch port connected to the router?

Accepted Answer

Configure the port as a trunk port.. The router uses subinterfaces with 802.1Q trunking to carry multiple VLANs over a single physical link. For this to work, the switch port connected to the router must be configured as a trunk port, which tags frames with VLAN IDs as they traverse the link. This allows the router to route between VLANs using its subinterfaces, each associated with a specific VLAN.

Answer

Configure the port as a routed port.

Answer

Configure the port as an access port in VLAN 1.

Answer

Configure the port as a dynamic desirable port.

Question 15

A network engineer is designing a campus network and needs to ensure high availability for the core layer. Which design best practice should be implemented?

Accepted Answer

Deploy two core switches configured with VSS or StackWise.. Deploying two core switches with VSS (Virtual Switching System) or StackWise provides both redundancy and active-active load balancing at the core layer. VSS virtualizes two physical switches into a single logical switch, eliminating the need for Spanning Tree Protocol (STP) on inter-switch links and enabling sub-second failover. This design ensures high availability by removing single points of failure and maximizing throughput between distribution and core layers.

Answer

Use a single distribution switch to simplify management.

Answer

Configure the core layer for Layer 2 switching only.

Answer

Use spanning-tree PortFast on all core switch ports.