220-1101 Hardware and Network Troubleshooting — Timed 10 Questions

Question 1

A technician is troubleshooting a desktop computer that cannot connect to the internet. The computer has a static IP address of 192.168.1.100 with a subnet mask of 255.255.255.0 and a default gateway of 192.168.1.1. The technician can ping 127.0.0.1 successfully but cannot ping 192.168.1.1. The link lights on the NIC and the switch port are solid. Which of the following should the technician check NEXT?

10 minute time limit — choose an answer to begin.

Accepted Answer

Check the subnet mask configuration. The loopback ping (127.0.0.1) succeeds, confirming the TCP/IP stack is working. The solid link lights indicate Layer 1 connectivity is healthy. Since the technician cannot ping the default gateway (192.168.1.1), the next logical step is to verify the subnet mask. If the subnet mask is misconfigured such that the host considers 192.168.1.1 to be outside its local subnet, the host will not send an ARP request for the gateway's MAC address and will treat the gateway as unreachable; as a result, it cannot forward any traffic off the local segment. Checking the subnet mask configuration is the appropriate next step before replacing hardware or changing firewall settings.

Answer

Replace the network cable

Answer

Run the Windows network troubleshooter

Answer

Disable the Windows firewall

Question 2

A laser printer is printing pages with dark vertical streaks. The technician replaces the toner cartridge and the imaging drum, but the streaks persist. Which of the following components should the technician check NEXT?

Accepted Answer

Fuser assembly. The correct answer is A: Fuser assembly. Dark vertical streaks are typically caused by a damaged or contaminated drum, but if the drum and toner cartridge have been replaced and the issue persists, the fuser assembly is the next most likely culprit. The fuser roller can have a nick, scratch, or debris that creates pressure lines, resulting in dark streaks on the page. The transfer roller, on the other hand, is responsible for transferring toner from the drum to the paper and typically causes light or white streaks when faulty, not dark streaks.

Answer

Transfer roller

Answer

Paper tray rollers

Answer

Laser scanner mirror

Question 3

A user reports that their desktop computer loses network connectivity intermittently. The technician finds that the RJ45 connector on the cable has a broken retention clip, but replacing the cable does not resolve the issue. The computer is connected to a wall jack in the office. The technician uses a cable tester on the wall jack and discovers that pins 4 and 5 are open (no continuity). Which of the following is the MOST likely cause of the intermittent connectivity?

Accepted Answer

Incorrect wiring standard on the wall jack. Pins 4 and 5 correspond to the blue pair (pair 3) in both T568A and T568B wiring. While 10/100BASE-T Ethernet only uses pins 1, 2, 3, and 6, 1000BASE-T requires all four pairs. An open on pins 4 and 5 at the wall jack indicates the blue pair is not properly terminated. Since replacing the computer cable did not resolve the issue, the fault is in the wall jack termination. Intermittent connectivity can occur if the punch-down connection is loose, causing the blue pair to sometimes make contact; when the pair is needed for gigabit operation, the link may flap or fail.

Answer

Faulty network interface card (NIC) in the computer

Answer

Damaged patch cable at the patch panel in the server room

Answer

Malfunctioning switch port

Question 4

A user reports that their desktop computer frequently loses network connectivity for a few seconds, then reconnects. The technician replaces the Ethernet cable and the wall jack, but the problem persists. The computer is connected to a managed switch. The technician checks the switch logs and sees no errors or discards. Which of the following should the technician check NEXT?

Accepted Answer

Check the duplex and speed settings on the NIC and the switch port for a mismatch. The symptom of intermittent connectivity that persists after replacing the cable and wall jack suggests a configuration issue at the NIC or switch port. A duplex mismatch can cause brief outages, but it typically produces interface errors (collisions, CRC, runts) on the affected side. However, such errors may not appear in the switch's event log, since interface counters are separate from logged events. Therefore, the next logical step is to verify that the duplex and speed settings on the NIC and switch port match.

Answer

Disable and re-enable the network adapter in Device Manager

Answer

Update the network adapter driver from the manufacturer's website

Answer

Replace the switch port with a known-working port

Question 5

A laser printer produces light ghost images of previously printed text on the following page. The technician has already replaced the toner cartridge and the imaging drum with new OEM components. The fuser appears to be heating properly. Which of the following is the NEXT component the technician should inspect or replace?

Accepted Answer

Erase lamp. In a laser printer, the erase lamp is responsible for discharging the photoconductive drum after the image is transferred. If it fails, residual latent images from the previous cycle remain and produce light ghost images. The primary charge roller applies a uniform charge to the drum; it does not erase the previous charge pattern. Since the toner cartridge, imaging drum, and fuser have already been ruled out, the next component to inspect/replace is the erase lamp.

Answer

Transfer roller

Answer

Primary charge corona / charge roller

Answer

Laser scanner unit

Question 6

A technician is troubleshooting a desktop computer that cannot connect to the internet. The computer has a static IP address of 192.168.1.100 with a subnet mask of 255.255.255.0 and a default gateway of 192.168.1.1. The technician can ping 127.0.0.1 successfully but cannot ping 192.168.1.1. The link lights on the NIC and the switch port are solid. Which of the following should the technician check NEXT?

10 minute time limit — choose an answer to begin.

Accepted Answer

B. (Clear CMOS) because the symptoms—power-on with all fans spinning, USB power present, but no display despite a solid monitor power LED—indicate a POST failure that persists after reseating the RAM. Since no diagnostic LEDs or speaker are available, the next best step is to clear the CMOS. This resets the BIOS/UEFI settings to default, which can resolve problems caused by incorrect video output configuration, memory timing errors, or overclocking that prevents the system from initializing the display.

Answer

A

Answer

C

Answer

D

Question 7

A user reports that their desktop computer loses network connectivity for several seconds whenever they open a large file transfer program. The technician checks the NIC properties and sees that the link speed is 100 Mbps, but the switch port is set to auto-negotiate and advertises up to 1000 Mbps (full duplex). The cable is a Cat5e cable that runs through the ceiling. Other computers in the same office have gigabit connections to the same switch. Which of the following is the MOST likely cause of the intermittent connectivity?

Accepted Answer

The Ethernet cable is damaged or has excessive length, causing the NIC to negotiate a lower speed.. The most likely cause is a damaged or excessively long Cat5e cable, assuming the switch port is set to auto-negotiate (capable of 1000 Mbps). The cable fault causes the NIC to fall back to 100 Mbps. During high traffic from the file transfer program, the marginal cable produces errors, causing intermittent link drops. The fact that other computers achieve gigabit on the same switch suggests the switch is not the issue, though the specific port configuration should be verified.

Answer

The switch port has a duplex mismatch.

Answer

The file transfer program is using an incompatible protocol.

Answer

The NIC driver is outdated and not compatible with gigabit.

Question 8

A user reports that their desktop computer shuts down randomly after about 10 minutes of use. The technician checks the event log and sees thermal warnings. The technician has verified that all fans are spinning and the CPU heatsink is properly attached. Which of the following should the technician do NEXT?

Accepted Answer

Apply new thermal paste between the CPU and heatsink.. The thermal warnings in the event log indicate that the CPU is overheating despite the fans spinning and the heatsink being properly attached. Over time, thermal paste can dry out or become less effective, reducing heat transfer from the CPU to the heatsink. Applying new thermal paste restores proper thermal conductivity, which is the most likely fix given the symptoms.

Answer

Replace the power supply.

Answer

Update the BIOS firmware.

Answer

Replace the CPU.

Question 9

A user reports that their laptop’s Wi-Fi connection is slow and drops frequently, but only when they are in the break room. Other laptops in the same area have no issues. The technician tests the signal strength in the break room and it is excellent. Which of the following is the most likely cause?

Accepted Answer

Interference from a microwave oven. The issue occurs only in the break room, indicating an environmental factor at that location. Other laptops work fine, so the access point is not overloaded, and the signal strength is excellent, ruling out range problems. A microwave oven is a common source of interference in break rooms, affecting Wi-Fi on the 2.4 GHz band. Since the problem is location-specific and the laptop works elsewhere, a faulty wireless adapter is unlikely.

Answer

The laptop’s wireless adapter is malfunctioning

Answer

The access point is overloaded with too many clients

Answer

The laptop is connected to the 5 GHz band which has shorter range

Question 10

A user reports that their desktop computer shuts down randomly after about 15 minutes of use. A technician checks the event log and finds a critical error related to a thermal event. The technician has verified that the CPU heatsink fan and all case fans are spinning, and the heatsink is securely attached. However, the computer still shuts down. Which of the following should the technician do NEXT?

Accepted Answer

Check the CPU thermal paste application.. The technician has already verified that the CPU heatsink fan and case fans are spinning and the heatsink is securely attached, which rules out a loose cooler or a failed fan. The critical thermal event error indicates the CPU is overheating despite these checks, so the most likely remaining cause is degraded or improperly applied thermal paste, which prevents efficient heat transfer from the CPU die to the heatsink. Reapplying high-quality thermal paste is the standard next step before considering component replacement.

Answer

Replace the power supply unit.

Answer

Update the BIOS firmware.

Answer

Replace the CPU.