220-1201 Timed Practice Test 2 — 10 Questions

Question 1

A technician is deploying 20 new tablets for a hospital's nursing staff. After configuring Wi-Fi and email, they find that the tablets will not connect to the corporate 5 GHz wireless network, only to the 2.4 GHz network. All tablets are the same model. What is the most likely cause?

10 minute time limit — choose an answer to begin.

Accepted Answer

The tablets only support 802.11b/g/n on the 2.4 GHz band and lack 5 GHz hardware support.. This is a common deployment issue where the device's wireless radio supports 2.4 GHz but not 5 GHz, or the 5 GHz channel is not supported. Older or budget tablets may lack 5 GHz capability, or the corporate network may use a 5 GHz channel (e.g., DFS channels) that the tablet's radio cannot use. Checking the tablet's Wi-Fi specifications is the correct first step.

Answer

The 5 GHz SSID is hidden and requires manual entry.

Answer

The corporate 5 GHz network requires 802.1X authentication that is not configured on the tablets.

Answer

The tablets have a defective Wi-Fi antenna.

Question 2

A technician is installing a new power supply in a high-end gaming PC. The PSU has two +12V rails rated at 20A each. The GPU requires a single +12V rail with at least 30A. What potential issue could arise?

Accepted Answer

The GPU may cause overcurrent protection to trip on one rail, causing shutdowns.. Multi-rail PSUs split the +12V output across separate rails, each with its own overcurrent protection. If the GPU draws more than 20A from one rail, it can trip the protection, causing shutdowns. Using a single-rail PSU or ensuring the GPU is connected across both rails (if the PSU allows) would avoid this.

Answer

The PSU will automatically combine the rails to provide 40A to the GPU.

Answer

The PSU will deliver stable power as long as the total wattage is sufficient.

Answer

The GPU will automatically draw power from both rails equally.

Question 3

A customer reports that their desktop computer, which is connected to the network via a wall jack, can access the internet but cannot see other computers on the same local network. The network uses a single switch and a router. What is the most likely misconfiguration causing this issue?

Accepted Answer

The computer's network profile is set to 'Public', disabling Network Discovery.. When a Windows computer's network profile is set to 'Public', the Windows Firewall automatically enables the 'Public' profile rules, which block Network Discovery and file sharing. This prevents the computer from seeing other devices on the local subnet even though internet access (which uses the default gateway) remains functional. The symptom—internet works but LAN visibility fails—is a classic indicator of a network profile misconfiguration.

Answer

The switch is a hub, not a switch.

Answer

The router is blocking multicast traffic.

Answer

The Ethernet cable is a crossover cable.

Question 4

A user is building a new gaming PC and wants to install 32 GB of DDR4 RAM in a dual-channel configuration. They have two 16 GB sticks. Which motherboard slots should they use to ensure dual-channel operation?

Accepted Answer

Slots 2 and 4 (alternating slots).. For dual-channel operation, memory modules must be installed in the correct slots, typically alternating colors or labeled as A2 and B2 (or slots 2 and 4) on most modern motherboards. This ensures the memory controller can access both sticks simultaneously, increasing bandwidth. The user manual or motherboard labeling is the definitive guide, but the common practice is to use the second and fourth slots from the CPU.

Answer

Slots 1 and 2 (adjacent to each other).

Answer

Slots 1 and 3 (alternating slots).

Answer

Any two slots will work; dual-channel is automatic.

Question 5

A customer reports that their external monitor connected via HDMI to a laptop shows a 'No Signal' message, even though the laptop screen works fine. The monitor has been tested with another device and works. What should you check first?

Accepted Answer

Press the function key to toggle display output.. This scenario tests basic display troubleshooting. The monitor works with another device, so the issue is likely with the laptop's video output or connection. The first step is to check if the laptop is set to output to the external display, often via a function key like F4 or F8.

Answer

Replace the HDMI cable.

Answer

Update the graphics driver.

Answer

Check the monitor's power cable.

Question 6

During a routine hardware upgrade, you install a new PCIe x16 graphics card into a desktop motherboard. The system powers on, but the display remains blank. The graphics card's fans are spinning. What should you check first on the motherboard?

Accepted Answer

The monitor cable is connected to the graphics card, not the motherboard. When a dedicated graphics card is installed, the motherboard often disables the integrated graphics port. If the monitor is still connected to the motherboard's video output, it will remain blank. The first step is to ensure the monitor cable is connected to the new graphics card's ports.

Answer

The BIOS settings for primary display adapter

Answer

The graphics card power connectors are properly attached

Answer

The PCIe slot is damaged

Question 7

A technician is configuring a network monitoring tool that uses SNMP to query network devices. Which two ports should be allowed for SNMP communication?

Accepted Answer

Port 161 and 162. SNMP uses UDP port 161 for sending queries and receiving responses between the manager and agents, and UDP port 162 for the agent to send unsolicited traps or informs to the manager. These two ports must be allowed through firewalls for proper SNMP communication.

Answer

Port 22 and 23

Answer

Port 80 and 443

Answer

Port 67 and 68

Question 8

A company's network uses a managed switch with VLANs. Users in VLAN 10 can ping the default gateway but cannot communicate with users in VLAN 20. The switch is connected to a router that handles inter-VLAN routing. What is the most likely misconfiguration?

Accepted Answer

The switch port connecting to the router is configured as an access port instead of a trunk.. The most likely misconfiguration is that the switch port connecting to the router is configured as an access port instead of a trunk. For inter-VLAN routing to work, the router must receive traffic from multiple VLANs on the same physical interface. A trunk port (using 802.1Q tagging) allows frames from VLAN 10 and VLAN 20 to be forwarded to the router, which then routes between them. An access port can only carry traffic for a single VLAN, so frames from VLAN 20 would be dropped or misdirected, preventing communication.

Answer

The router's firewall is blocking traffic between VLANs.

Answer

The default gateway for VLAN 20 is misconfigured.

Answer

The switch has Spanning Tree Protocol enabled, blocking the link.

Question 9

A company has a network with the IP range 172.16.0.0/16. They need to create 8 separate subnets for different departments, each with at least 1000 usable hosts. What subnet mask should be used?

Accepted Answer

255.255.224.0. To support 8 subnets with at least 1000 usable hosts each, you need to borrow enough bits from the host portion to create 8 subnets (2^3 = 8) while leaving at least 10 host bits (2^10 - 2 = 1022 usable hosts). Starting from /16, borrowing 3 bits gives a /19 prefix, which translates to subnet mask 255.255.224.0. This mask provides exactly 8 subnets and 8190 total hosts per subnet (2^13 - 2 = 8190), well exceeding the 1000-host requirement.

Answer

255.255.240.0

Answer

255.255.248.0

Answer

255.255.192.0

Question 10

A technician is setting up a small office network with a router, a switch, and a wireless access point. The router has only one LAN port. The technician needs to connect the switch and the WAP to the router, but the switch has no uplink port. Which hardware component should the technician use to connect both devices to the router?

Accepted Answer

Connect the router to the switch, then connect the WAP to the switch.. This question tests knowledge of network topology and the use of additional switches. Since the router has only one LAN port, a switch is needed to expand the number of available ports. The correct answer is to connect the router to the switch, and then connect the WAP to the switch. The switch's ports are typically all the same, so no special uplink port is required (modern switches use Auto-MDIX).

Answer

Use a crossover cable to connect the router directly to the WAP.

Answer

Use a hub between the router and the switch.

Answer

Configure the switch as a router to connect to the WAP.